I am trying to use PXE/kickstart to load FC7 on an appliance. My
initrd.img and vmlinuz are from FC7 and are loading but my console
output looks like the following:
Linux version 2.6.21-1.3194.fc7
(kojibuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2
20070502 (Red Hat 4.1.2-12)) #1 SMP Wed May 23 22:35:01 EDT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end:
000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end:
00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end:
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000003f6f0000 end:
000000003f7f0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000003f7f0000 size: 0000000000003000 end:
000000003f7f3000 type: 4
copy_e820_map() start: 000000003f7f3000 size: 000000000000d000 end:
000000003f800000 type: 3
copy_e820_map() start: 00000000fec00000 size: 0000000001400000 end:
0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7f0000 (usable)
BIOS-e820: 000000003f7f0000 - 000000003f7f3000 (ACPI NVS)
BIOS-e820: 000000003f7f3000 - 000000003f800000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f53b0
Using x86 segment limits to approximate NX protection
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 260080
early_node_map[1] active PFN ranges
0: 0 -> 260080
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F7060, 0014 (r0 IntelR)
ACPI: RSDT 3F7F3000, 002C (r1 IntelR AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 3F7F3040, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 3F7F30C0, 3BE4 (r1 INTELR AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 3F7F0000, 0040
ACPI: APIC 3F7F6CC0, 005C (r1 IntelR AWRDACPI 42302E31 AWRD 0)
ACPI: PM-Timer IO Port: 0x408
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f800000:bf400000)
Built 1 zonelists. Total pages: 258049
Kernel command line: load_ramdisk=1
ks=nfs:10.254.13.1:/home/tftpboot/kickstart/10.254.13.113-kickstart
initrd=initrd-2.6.21-1.3194.fc7.img dd ksdevice=eth0
console=ttyS0,38400n8 BOOT_IMAGE=vmlinuz
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c077c000 soft=c075c000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2000.495 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1022916k/1040320k available (2066k kernel code, 16712k reserved,
1092k data, 240k init, 122816k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc071b000 - 0xc0757000 ( 240 kB)
.data : 0xc0604a4a - 0xc0715cb4 (1092 kB)
.text : 0xc0400000 - 0xc0604a4a (2066 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4003.06 BogoMIPS
(lpj=2001531)
Security Framework v1.0.0 initialized
SELinux: Initializing.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Celeron(R) CPU 2.00GHz stepping 09
Total of 1 processors activated (4003.06 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
Time: 9:44:25 Date: 10/08/107
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb310, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:00: iomem range 0xcd800-0xcffff has been reserved
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
pnp: 00:03: ioport range 0x400-0x4bf could not be reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: a000-afff
MEM window: ec000000-ec0fffff
PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3477k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1194515064.774:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ksign: Installing public key data
Loading keyring
- Added public key 65F8109C338BBD41
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is
not present [20070126]
ACPI: Thermal Zone [THRM] (23 C)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Magic number: 15:268:727
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 820k
Red Hat nash version 6.0.9 starting
Mounting proc filesystem
Mounting sysfs filesystem
Creating /dev
Creating initial device nodes
Setting up hotplug.
input: PS/2 Generic Mouse as /class/input/input2
Creating block device nodes.
Loading uhci-hcd.ko module
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000b800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000b000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Loading ohci-hcd.ko module
Loading ehci-hcd.ko module
Loading mbcache.ko module
Loading jbd.ko module
Loading ext3.ko module
Loading scsi_mod.ko module
SCSI subsystem initialized
Loading sd_mod.ko module
Loading libata.ko module
Loading ata_generic.ko module
Loading ata_piix.ko module
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001cc00
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001cc08
irq 15
scsi0 : ata_piix
ata1.00: ata_hpa_resize 1: sectors = 78165360, hpa_sectors = 78165360
ata1.00: ATA-6: WDC WD400JB-00JJA0, 05.01C05, max UDMA/100
ata1.00: 78165360 sectors, multi 16: LBA
ata1.00: ata_hpa_resize 1: sectors = 78165360, hpa_sectors = 78165360
ata1.00: configured for UDMA/33
scsi1 : ata_piix
scsi 0:0:0:0: Direct-Access ATA WDC WD400JB-00JJ 05.0 PQ: 0 ANSI: 5
SCSI device sda: 78165360 512-byte hdwr sectors (40021 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sda: 78165360 512-byte hdwr sectors (40021 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
Waiting for driver initialization.
Loading dm-mod.ko module
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@xxxxxxxxxx
Loading dm-mirror.ko module
Loading dm-zero.ko module
Loading dm-snapshot.ko module
Making device-mapper control node
Scanning logical volumes
Reading all physical volumes. This may take a while...
Found volume group "VolGroup00" using metadata type lvm2
Activating logical volumes
2 logical volume(s) in volume group "VolGroup00" now active
Trying to resume from /dev/VolGroup00/LogVol01
No suspend signature on swap, not resuming.
Creating root device.
Mounting root filesystem.
mount: could not find filesystem '/dev/root'
Setting up other filesystems.
Setting up new root fs
setuproot: moving /dev failed: No such file or directory
no fstab.sys, mounting internal defaults
setuproot: error mounting /proc: No such file or directory
setuproot: error mounting /sys: No such file or directory
Switching to new root and running init.
umounting old /dev
umounting old /proc
umounting old /sys
switchroot: mount failed: No such file or directory
Booting has failed.
Kernel panic - not syncing: Attempted to kill init!
Any and all thoughts would be greatly appreciated!
