Hi all, I'm having quite a challenge getting my Acer TM6460 to resume from suspend with kernel 2.6.22.1-27 (and-33) and using the vesa driver for X. It worked fine with up-to-date FC6: - suspend works with # pm-suspend --quirk-s3-mode - resume fails. The screen remains black (no backlit) and the HD led comes on the first time but from a similar problem with an Acer Ferrari 4005 I know it must flicker afterward which it does not. So I went to the pages at: http://people.freedesktop.org/~hughsient/quirk/quirk-suspend-index.html and followed the advice. The debug info is: [root@localhost ~]# cat dmesg.txt | grep "hash matches" hash matches drivers/base/power/resume.c:28 hash matches device 0000:09:04.1 This device is the cardbus bridge: [root@localhost ~]# cat dmesg.txt | grep "0000:09:04.1" PCI: Bus 10, cardbus bridge: 0000:09:04.1 PCI: Enabling device 0000:09:04.1 (0080 -> 0083) ACPI: PCI Interrupt 0000:09:04.1[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:09:04.1 to 64 Yenta: CardBus bridge found at 0000:09:04.1 [1025:010d] hash matches device 0000:09:04.1 I have no idea if this indicates a problem with the cardbus or not. Afaict the module list below shows no related module. Modules loaded before issuing the pm-suspend --quirk-s3-mode command: [root@localhost ~]# lsmod Module Size Used by snd_hda_intel 243416 1 snd_seq_dummy 7877 0 snd_seq_oss 33473 0 snd_seq_midi_event 11073 1 snd_seq_oss snd_seq 50609 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 11981 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 43457 0 snd_mixer_oss 19521 1 snd_pcm_oss snd_pcm 74949 2 snd_hda_intel,snd_pcm_oss snd_timer 24901 2 snd_seq,snd_pcm snd 53317 10 snd_hda_intel,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer tg3 104901 0 soundcore 11681 1 snd snd_page_alloc 13769 2 snd_hda_intel,snd_pcm sr_mod 20837 0 cdrom 37089 1 sr_mod sg 37469 0 ata_generic 11589 0 ata_piix 18757 3 libata 119985 2 ata_generic,ata_piix sd_mod 31297 4 scsi_mod 140621 4 sr_mod,sg,libata,sd_mod ext3 125513 2 jbd 59881 1 ext3 mbcache 12485 1 ext3 [root@localhost ~]# cat /etc/pm/config.d/unload_modules SUSPEND_MODULES="iwl3945 mac80211 cfg80211 kvm kvm_intel fw_ohci fw_core ehci_hcd ohci_hcd uhci_hcd i2c_i801 i2c_core acpi_cpufreq cpufreq_ondemand" [root@localhost ~]# cat /etc/modprobe.d/blacklist [snip] blacklist video blacklist sbs blacklist button blacklist bay blacklist dock blacklist battery blacklist ac blacklist loop blacklist kvm_intel blacklist kvm blacklist arc4 blacklist firewire_ohci blacklist ecb blacklist blkcipher blacklist firewire_core blacklist irda blacklist crc_itu_t blacklist rtc_cmos blacklist ehci_hcd blacklist ohci_hcd blacklist uhci_hcd [snip] [root@localhost ~]# cat /etc/modprobe.conf [snip] alias video off alias sbs off alias button off alias bay off alias dock off alias battery off alias ac off alias loop off alias kvm_intel off alias kvm off alias arc4 off alias ecb off alias blkcipher off [snip] The results of booting with various parameters are: Boot param result ---------------------------------------------------------------------- vga=792 no working resume vga=normal no working resume maxcpus=1 no working resume noapic no working resume nolapic no working resume noapic nolapic no working resume nolapic_timer no working resume nohz=off no working resume ec_burst=1 no working resume nolapic ec_burst=1 no working resume acpi=noirq ec_burst=1 no working resume >From the Acer Ferrari days I remember booting with parameters like (iirc) noapic acpi_irq_balance irqfixup pci=noacpi. This did not result in a working resume on the TM6460 either. Anyone have a suggestion what else I can try to get resume going? Thanks! Patrick
