I've seen the same problem on F7 install. It most likely has to do with
nvidia drivers, and most definitely video drivers in general.
As a workaround, you can set the mouse pointer to software rendered mode
(normally, the pointer is hardware-accelerated)
Tom Diehl wrote:
Hi,
I just installed f7 on a new box. Once the machine is up and running the
mouse pointer disappears. The mouse is working because if I move it
carefully I can use it to navigate the menus at the top of the screen. I
was
able to turn on the option to highlight the mouse when the ctrl key is
pressed
which allows me to kind of operate the machine.
I have installed all of the updates but I cannot figure out how to get the
mouse pointer to show up. Does anyone have any ideas how to fix this.
I am not running any of the nVidia propriatory modules and I would like to
avoid that if possible.
Below is the output of lspci:
[root@tigger2 pts0 ~]# lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:05.0 VGA compatible controller: nVidia Corporation C51G [GeForce
6100] (rev a2)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a3)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev f1)
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller
(rev f1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio
(rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
03:05.0 Communication controller: Conexant HSF 56k Data/Fax Modem
03:08.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788
Gigabit Ethernet (rev 03)
[root@tigger2 pts0 ~]#
Suggestions?
Regards,
