On Thursday 14 June 2007 13:48:28 antonio montagnani wrote: > I am running a D-Link G-650 that was o.k on FC6. > I made afresh installation, I installed madwifi from freshrpms, then I > rebooted. Now if I open the Network administration page I do not see the > wifi-card (no ath0, no wifi0), but > the output of lspi is: > > 03:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 > 802.11abg NIC (rev 01) > > the output of lsmod is: > Module Size Used by > wlan_tkip 15872 0 > wlan_ccmp 11776 0 > wlan_scan_sta 16512 1 > ath_pci 92832 0 > ath_rate_sample 15744 1 > wlan 186052 6 > wlan_tkip,wlan_ccmp,wlan_scan_sta,ath_rate_sample,ath_pci > ath_hal 195408 3 ath_rate_sample,ath_pci > > so all necessary modules are loaded... > > If I issue an ipconfig I get: > > ifconfig > ath0 Link encap:Ethernet HWaddr 00:15:E9:2F:EE:A7 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:14 errors:0 dropped:0 overruns:0 frame:0 > TX packets:76 errors:1 dropped:1 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:2145 (2.0 KiB) TX bytes:15878 (15.5 KiB) > > eth0 Link encap:Ethernet HWaddr 00:03:0D:04:A3:10 > inet addr:192.168.0.20 Bcast:192.168.0.255 Mask:255.255.255.0 > inet6 addr: fe80::203:dff:fe04:a310/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:1571 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1549 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:1155014 (1.1 MiB) TX bytes:430040 (419.9 KiB) > Interrupt:16 Base address:0x2000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:14 errors:0 dropped:0 overruns:0 frame:0 > TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1036 (1.0 KiB) TX bytes:1036 (1.0 KiB) > > wifi0 Link encap:UNSPEC HWaddr > 00-15-E9-2F-EE-A7-78-19-00-00-00-00-00-00-00-00 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:20649 errors:0 dropped:0 overruns:0 frame:11548 > TX packets:687 errors:0 dropped:1 overruns:0 carrier:0 > collisions:0 txqueuelen:199 > RX bytes:2750101 (2.6 MiB) TX bytes:52867 (51.6 KiB) > Interrupt:16 > > > How can I have an wifi0 or ath0 that I do not see in the Network > configuration window???? > > Tnx for help > What happen if you try to configure your wireless network using iwconfig, I mean, from the CLI? Does it work? -- Manuel Arostegui Ramirez. Electronic Mail is not secure, may not be read every day, and should not be used for urgent or sensitive issues.
