On Wed, 2006-11-29 at 15:10 -0700, Don Raikes wrote: > I ran: > > modprobe sky2 > > and got some good feedback. > I then ran > > ifup eth0 > > no output. > > I ran: > > ifconfig and got: > eth0 Link encap:Ethernet HWaddr 00:11:11:B2:ED:CC > inet addr:192.168.0.125 Bcast:192.168.0.125 Mask:255.255.255.255 That's your problem. Try "ifconfig eth0 netmask 255.255.255.0" and try pinging your router then. Also fix /etc/sysconfig/ifcfg-eth0 and fix the netmask there for future boots. > inet6 addr: fe80::211:11ff:feb2:edcc/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:31 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:5702 (5.5 KiB) > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:56 errors:0 dropped:0 overruns:0 frame:0 > TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:10761 (10.5 KiB) TX bytes:10761 (10.5 KiB) > > vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:144 errors:0 dropped:0 overruns:0 frame:0 > TX packets:4774 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:14876 (14.5 KiB) TX bytes:1471983 (1.4 MiB) > > xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:4469 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1371625 (1.3 MiB) TX bytes:0 (0.0 b) > > Finally, I ran > > ping 192.168.0.1 (my router) > > I got unable to reach network. > > I feel like there is a step I forgot. > -----Original Message----- > From: fedora-list-bounces@xxxxxxxxxx > [mailto:fedora-list-bounces@xxxxxxxxxx]On Behalf Of GérardMilmeister > Sent: Wednesday, November 29, 2006 2:36 PM > To: For users of Fedora > Subject: Re: FC6 and Marvell Yukon network card > > > On Wed, 2006-11-29 at 14:20 -0700, Don Raikes wrote: > > Hello, > > > > I just installed FC6 on my gateway computer. The computer has a Marvell Yukon 88E8050 network chipset, and now I have no network support. > > > > I found a copy of the sk98lin driver for fc6 in rpm format, but it was for the upgraded kernel 2.6.18-1.2849fc6, but my installed kernel is 2.6.18-1.2798fc6. > > > > I downloaded the manufacturer's installation package, but when I try to compile it I keep getting errors saying that there are problems with the kernel headers. > > > > I downloaded and installedthe kernel sources as discussed at: > > http://www.g-loaded.eu/2005/12/14/the-complete-fedora-kernel-headers/ > The sk98lin is obsolete, I think. You should try with sky2. > -- > Gérard Milmeister > Langackerstrasse 49 > CH-8057 Zürich > > -- > fedora-list mailing list > fedora-list@xxxxxxxxxx > To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list > ---------------------------------------------------------------------- - Rick Stevens, Senior Systems Engineer rstevens@xxxxxxxxxxxxxxx - - VitalStream, Inc. http://www.vitalstream.com - - - - Grabel's Law: 2 is not equal to 3--not even for large values of 2. - ----------------------------------------------------------------------
