john... just out of curiousity... did you call phoenix??? given that it's a phoenix bios.. their cust support might have some pointers to give you? also, what about intel directly? as an aside... when you do get the soln, would you mind writing up the prob/solution, and posting it back to this list!!! good luck, probs like these can be a pain!!! -bruce -----Original Message----- From: fedora-list-bounces@xxxxxxxxxx [mailto:fedora-list-bounces@xxxxxxxxxx]On Behalf Of John Rowan Sent: Saturday, August 20, 2005 6:30 AM To: For users of Fedora Core releases Subject: Re: SuperMicro 5013 Joel Jaeggli wrote: > > On Fri, 19 Aug 2005, John Rowan wrote: > >> One of my customers was tired of the noise levels from the Proliant >> 6400R in his office. He wanted something that would be quieter but >> also faster. TigerDirect sent him an email saying the 3GHz SuperMicro >> 5013 1U was the device he longed for. He ordered the 3GHz 1Gigabyte >> RAM dual 120 gigabyte SATA disk unit since the web site said it >> worked with Linux. I tried installing Fedora Core 4 which said it >> was successful but upon rebooting the machine it hung at a GRUB >> prompt for 30 seconds then rebooted. > > > The supermicro 5013 is a chassis, Which supermicro mainboard is > actually in this chassis. It sounds like a single p4 mainboard with > sata but that narrows it down to about half the 5013 variants. rh9 is > going to be too old by far for this system, the sweet spot for getting > it working is going to be in the fc2-fc4 range (2.6 kernel) once we > know that motherboard variant and therefore chipset, it would be > easier to recomend a course of action. > >> I reverted to RH 9.0 but it doesn't have drivers for the SATA RAID >> controller. I also tried SuSE Pro 9.1 but that also does not have >> drivers for this RAID controller. I've done 9 installs with FC4, >> RH9 or SuSE Pro 9.1 today all failing. FC4 has drivers for the >> controller but after installation it fails to boot. RH9 and SuSE do >> not recognize the drivers I've downloaded from SuperMicro.com. Does >> anyone know where I can get drivers for RH9 or SuSE, or why the >> machine hangs for 30 seconds after reboot with a GRUB prompt on the >> screen? >> >> >> > When I boot the system it displays Phoenix - Award BIOS V6.00PG SuperMicro P4SCA/P4SCE BIOS 1.3A On the bottom of the initial screen on left side it says 4/14/2005 - Canterwood - 6A79BSX9C-00 Pressing CTRL-I brings up the screen to configure the level of RAID (0 or 1) On top of that screen it says Intel RAID for Serial ATA V3.5.0.3003 The front of the case says SuperMicro but on the top (slide off) cover it says Visionman. I've been to both SuperMicro.com and Visionman.com web sites but neither has a Linux driver for Intel. They have drivers they say are for RH 9 with specific kernel versions but neither of those work. I don't understand why the Fedora Core 4 installation (which recognized the RAID controller and loaded the correct driver) failed to boot after it said the installation was complete. I'm in the process of installing FC4 for the fifth time now to see if there is some way to salvage this hardware. It's looking more and more like I'll be getting an RMA from TigerDirect.com for this one. -- John Rowan Rownetco, Inc. Office: 973 697 8019 Fax: 973 697 4443 Cell: 973 229 5742 E-Mail: rowan@xxxxxxxxxxxx Web: http://www.rownetco.com -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
