On Mon, 2005-07-18 at 02:37 +0530, Rahul Sundaram wrote: > Hi > > > > > When I run Desktop || System Setting || Network on the GNOME toolbar > > and try to add a a new wireless device, a box called "Select Wireless > > Device" comes up which only lists "Other wireless card." When I select > > this, a box comes up which says "Select Ethernet Adapter" with a list > > of adapter types but none of which I recognize as equivalent to my > > Dell Wireless card. > > whats the output of lspci. One would need to know the exact model to > suggest something > > regards > Rahul > I have not used the lspci command before; I am not sure which information from it would be most helpful. Here is the output from lspci -bvv: ======================================================= 00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) Subsystem: Dell: Unknown device 015f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at e0000000 (32-bit, prefetchable) Capabilities: [40] Vendor Specific Information Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1 00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) Subsystem: Dell: Unknown device 015f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) Subsystem: Dell: Unknown device 015f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:01.0 PCI bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to AGP Controller (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fc000000-fdffffff Prefetchable memory behind bridge: e8000000-efffffff Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- 00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell: Unknown device 015f Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at bf80 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell: Unknown device 015f Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at bf40 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell: Unknown device 015f Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at bf20 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Dell: Unknown device 015f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 0: Memory at f4fffc00 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000d000-0000efff Memory behind bridge: f6000000-fbffffff Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Dell: Unknown device 015f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 0 Region 0: I/O ports at 01f0 Region 1: I/O ports at 03f4 Region 2: I/O ports at 0170 Region 3: I/O ports at 0374 Region 4: I/O ports at bfa0 Region 5: Memory at 20000000 (32-bit, non-prefetchable) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) Subsystem: Dell: Unknown device 015f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 0: I/O ports at b800 Region 1: I/O ports at bc40 Region 2: Memory at f4fff800 (32-bit, non-prefetchable) Region 3: Memory at f4fff400 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf [FireGL 9000] (rev 01) (prog-if 00 [VGA]) Subsystem: Dell: Unknown device 0149 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min), Cache Line Size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at e8000000 (32-bit, prefetchable) Region 1: I/O ports at c000 Region 2: Memory at fcff0000 (32-bit, non-prefetchable) Capabilities: [58] AGP version 2.0 Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01) Subsystem: Dell: Unknown device 015f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 11 Region 0: Memory at faffe000 (32-bit, non-prefetchable) Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 02:02.0 Network controller: Broadcom Corporation BCM4309 802.11a/b/g (rev 03) Subsystem: Dell Truemobile 1450 MiniPCI Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 11 Region 0: Memory at faffc000 (32-bit, non-prefetchable) 02:04.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02) Subsystem: Dell: Unknown device 015f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size 20 Interrupt: pin A routed to IRQ 255 Region 0: Memory at 20001000 (32-bit, non-prefetchable) Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 20400000-207ff000 (prefetchable) Memory window 1: 20800000-20bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 02:04.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller (prog-if 10 [OHCI]) Subsystem: Dell: Unknown device 015f Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at faffb800 (32-bit, non-prefetchable) Region 1: Memory at faff4000 (32-bit, non-prefetchable) Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot +,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ ======================================================= Thanks for your help. (And sorry about the long signatures and HTML code in previous emails.) ===== May the peace of the Lord be with you! Jeff Falter, jfalter@xxxxxxxx
