On Mon, 2005-06-06 at 16:58 -0500, Jeff Vian wrote: > On Mon, 2005-06-06 at 05:35 -0400, Marcus O. White wrote: > > G'day All, > > > > Finally upgraded remaining RHL 9.0 workstation to FC3. Now when I > > attempt to access my Sony Mavica CD-1000 digital camera via USB it no > > longer works. Whereas it worked under RHL 9.0. The system recognizes the > > camera, as can seen from the following: > > > > Jun 6 05:21:22 tbird kernel: usb 4-1: new full speed USB device using > > uhci_hcd and address 3 > > Jun 6 05:21:24 tbird kernel: SCSI subsystem initialized > > Jun 6 05:21:24 tbird kernel: Initializing USB Mass Storage driver... > > Jun 6 05:21:24 tbird kernel: scsi0 : SCSI emulation for USB Mass > > Storage devices > > Jun 6 05:21:24 tbird kernel: usbcore: registered new driver usb-storage > > Jun 6 05:21:24 tbird kernel: USB Mass Storage support registered. > > Jun 6 05:21:29 tbird kernel: Vendor: SONY Model: DSC DDX-G2000 > > Rev: 1.17 > > Jun 6 05:21:29 tbird kernel: Type: CD-ROM > > ANSI SCSI revision: 02 > > Jun 6 05:21:29 tbird scsi.agent[9551]: cdrom > > at /devices/pci0000:00/0000:00:10.2/usb4/4-1/4-1:1.0/host0/target0:0:0/0:0:0:0 > > Jun 6 05:21:30 tbird kernel: sr0: scsi3-mmc drive: 8x/8x writer > > xa/form2 cdda pop-up > > sr0 is the driver > > > Jun 6 05:21:30 tbird fstab-sync[9614]: added mount > > point /media/cdrecorder2 for /dev/scd0 > > Jun 6 05:21:30 tbird kernel: cdrom: This disc doesn't have any tracks I > > recognize! > > > > Normal message for a usb attached cdrom with no disk in the drive. It > sees the drive but can't access the disk. > > Everything up to this point seems normal > > > > When I attempt to mount it I see the following messages: > > [root@tbird ~]# mount -t udf /dev/sr0 /media/cdrecorder2 > > You are trying to mount /dev/sr0 (the driver). In the message about the > mount point above it says the device is /dev/scd0. Thus it cannot be > mounted with your command. > > Since the fstab entry has been made, if you have need to manually mount > it the command (as root) would be "mount /media/cdrecorder2". The rest > of the data is taken from the fstab entry. Media device by default will > automount when a disk is available. > > Did you even look at /media/cdrecorder2 to see if the content was > already mounted? Mine shows an icon on the desktop when I attach a > media device (cdrom, camera, flash disk, etc.) and it auto-mounts. > > Also, you need to have a disk in the drive with a recognized filesystem > to do the mount. Verify that is the case. > > A friend had a Sony camera that used a cdrom for the pictures. The > pictures were not actually in a filesystem until he told the camera to > close the session and thus could not be read directly on another cdrom > drive. I never tried to connect it to my linux machine so I don't know > if it would have been mountable while in the camera or not. > > I tried the /dev/scd0 and /dev/sr0 (after manually creating it). Yes, I checked to see if it had already mounted. This camera uses a 3" CD to store the photos. I've heard that some users had to "finalize" the CD, but that defeats the purpose of accessing it from the camera. I last used this very same camera and CD a few days ago prior to upgrading to FC3... Maybe I need to downgrade it or at least load the last kernel rpm... Any other ideas? -- Marcus O. White <1lnxraider@xxxxxxxxxxx>
