what is a good gui to create dao audio cds directly from wav? the built in nautilus cd creator works ok when i want to burn data to a disc, but i can't seem to find any options to create dao audio discs. i went ahead and installed gcombust, but it gives me the following error when i left the defaults alone: -------------- scsidev: '0,6,0' scsibus: 0 target: 6 lun:0 /usr/bin/cdrecord: No such file or directory. Cannot open '/dev/pg6'. Cannot open SCSI driver. /usr/bin/cdrecord: For possible targets try 'cdrecord -scanbus'. /usr/bin/cdrecord: For possible transport specifiers try 'cdrecord dev=help'. --------------- so here is the output when i run cdrecord -scanbus: --------------- $ cdrecord -scanbus Cdrecord-Clone 2.01-dvd (--) Copyright (C) 1995-2004 Jörg Schilling Note: This version is an unofficial (modified) version with DVD support Note: and therefore may have bugs that are not present in the original. Note: Please send bug reports or support requests to http://bugzilla.redhat.com/bugzilla Note: The author of cdrecord should not be bothered with problems in this version. scsidev: 'ATA' devname: 'ATA' scsibus: -2 target: -2 lun: -2 Linux sg driver version: 3.5.27 Using libscg version 'schily-0.8'. cdrecord: Warning: using inofficial libscg transport code version (schily - Red Hat-scsi-linux-sg.c-1.83-RH '@(#)scsi-linux-sg.c 1.83 04/05/20 Copyright 1997 J. Schilling'). scsibus0: 0,0,0 0) 'HP ' 'CD-Writer+ 8100 ' '1.0g' Removable CD-ROM 0,1,0 1) 'Compaq ' 'DVD-ROM DVD-114 ' '1.14' Removable CD-ROM 0,2,0 2) * 0,3,0 3) * 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) * ---------------------------- and here is the output when i run cdrecord dev=help: ----------------------------- $ cdrecord dev=help Cdrecord-Clone 2.01-dvd (--) Copyright (C) 1995-2004 Jörg Schilling Note: This version is an unofficial (modified) version with DVD support Note: and therefore may have bugs that are not present in the original. Note: Please send bug reports or support requests to http://bugzilla.redhat.com/bugzilla Note: The author of cdrecord should not be bothered with problems in this version. Supported SCSI transports for this platform: Transport name: sg Transport descr.: Generic transport independent SCSI Transp. layer ind.: Target specifier: bus,target,lun Target example: 1,2,0 SCSI Bus scanning: supported Open via UNIX device: not supported Transport name: pg Transport descr.: SCSI transport for ATAPI over Parallel Port Transp. layer ind.: Target specifier: bus,target,lun Target example: 1,2,0 SCSI Bus scanning: supported Open via UNIX device: not supported Transport name: ATA Transport descr.: ATA Packet specific SCSI transport Transp. layer ind.: ATAPI: Target specifier: bus,target,lun Target example: ATAPI:1,2,0 SCSI Bus scanning: supported Open via UNIX device: not supported Transport name: ATA Transport descr.: ATA Packet specific SCSI transport using sg interface Transp. layer ind.: ATA: Target specifier: bus,target,lun Target example: 1,2,0 SCSI Bus scanning: supported Open via UNIX device: not supported Transport name: RSCSI Transport descr.: Remote SCSI Transp. layer ind.: REMOTE: Target specifier: rscsi@host:bus,target,lun Target example: REMOTE:rscsi@host:1,2,0 SCSI Bus scanning: supported Open via UNIX device: not supported ----------------------------------- The only setting a messed with after that were the CD-Recorder device options...I tried setting SCSI-bus=0, Target=0 & Lun=0, based on the output of cdrecord -scanbus, but this pretty much generated the same error. So i'm clueless on where to go next. Thanks!
