Angelo Machils wrote:
Hello there!
I have an AMD Athlon XP 2600+ with the INI 9400u SCSI card. On this
card there is only one device attached, a HP DLT4000 tape unit (2 HP
DDS-3 tape units are supposed to be added later). In my
/var/log/messages file I keep seeing these entries:
Feb 21 12:56:41 imhotep kernel: sda: test WP failed, assume Write
Enabled
Feb 21 12:56:41 imhotep kernel: sda: assuming drive cache: write through
Feb 21 12:56:43 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:43 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:43 imhotep kernel: sda: test WP failed, assume Write
Enabled
Feb 21 12:56:43 imhotep kernel: sda: assuming drive cache: write through
Feb 21 12:56:45 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:45 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:45 imhotep kernel: sda: test WP failed, assume Write
Enabled
Feb 21 12:56:45 imhotep kernel: sda: assuming drive cache: write through
Feb 21 12:56:47 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:47 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:47 imhotep kernel: sda: test WP failed, assume Write
Enabled
Feb 21 12:56:47 imhotep kernel: sda: assuming drive cache: write through
Feb 21 12:56:49 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:49 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:49 imhotep kernel: sda: test WP failed, assume Write
Enabled
Feb 21 12:56:49 imhotep kernel: sda: assuming drive cache: write through
Feb 21 12:56:51 imhotep kernel: sddr09: could not read card info
Feb 21 12:56:51 imhotep kernel: sddr09: could not read card info
An sda entry would mean there is a SCSI drive attached, but there is
none. What is meant with sddr09 I have no idea! When I go into the
BIOS of the card, it only sees the DLT drive.
What's in /proc/scsi/scsi ?
Paul.
Hi!
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: Sandisk Model: ImageMate SDDR-0 Rev: 0208
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 02 Lun: 00
Vendor: Quantum Model: DLT4000 Rev: DA97
Type: Sequential-Access ANSI SCSI revision: 02
The SanDisk is actually a USB cardreader.
Fine. The system is checking the write enable status of the SanDisk.
Until you put media in it, you'll continue to see those messages. The
system treats USB card reader/writer devices as though they were SCSI
disks--in this case with removable media.
SCSI tape devices are named "/dev/st0" (ST for "SCSI Tape"). I'll bet
if you do an "mt -f /dev/st0 status", you'll see the tape whirr and get
a status message about the drive and/or media.
Remember, "/dev/sd" = "SCSI Disk", "/dev/st" = "SCSI TAPE", "/dev/sr" =
"SCSI Removable" (CD-ROM/CD-RW/DVD/DVD-RW)
----------------------------------------------------------------------
- Rick Stevens, Senior Systems Engineer rstevens@xxxxxxxxxxxxxxx -
- VitalStream, Inc. http://www.vitalstream.com -
- -
- Heisenberg _may_ have slept here -
----------------------------------------------------------------------
