Hi, I've a GA-7N400 Pro and a GA-7N400 Pro 2 that have this same controller, but I can't compile the driver modules. I receive lots of erros, missing headers, missing declarations, etc... I've get the v.145 driver... How do you make it compile? ATS, -- Alexandre Cavalcante Alencar (Skarmeth) alexandre@xxxxxxxxxxxxx skarmeth@xxxxxxxxxxxxx http://people.debian-ce.org/skarmeth/ Grupo de Usuários GNU/Linux e de Software Livre do Ceará - Debian-CE http://www.debian-ce.org http://listas.cipsga.org.br/cgi-bin/mailman/listinfo/debian-ce Projeto Software Livre Ceará - PSL-CE http://psl-ce.softwarelivre.org http://listas.softwarelivre.org/mailman/listinfo/psl-ce Linux Registred User....: 260571 ICQ Instant Message.....: 87355854 Yahoo Instant Message...: Skarmeth Skype IP Telephony......: Skarmeth On Sat, 2004-11-13 at 07:02, Mile Davidovic wrote: > Hi Folks > > Is anyone succedd to use ITE8212 Raid controler (on Gigabyte boards called > GigaRaid) on FC3? > I have some problem with building modules but dmesg shows: > Found Controller: IT8212 UDMA/ATA133 RAID Controller > FindDevices: device 0 is IDE > FindDevices: device 1 is IDE > Channel[0] BM-DMA at 0xA400-0xA407 > Channel[1] BM-DMA at 0xA408-0xA40F > scsi2 : ITE RAIDExpress133 > Vendor: ITE Model: IT8212F Rev: 1.3 > Type: Direct-Access ANSI SCSI revision: 00 > SCSI device sdb: 488397166 512-byte hdwr sectors (250059 MB) > sdb: asking for cache data failed > sdb: assuming drive cache: write through > sdb: sdb1 > Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0 > Vendor: ITE Model: IT8212F Rev: 1.3 > Type: Direct-Access ANSI SCSI revision: 00 > SCSI device sdc: 488397166 512-byte hdwr sectors (250059 MB) > sdc: asking for cache data failed > sdc: assuming drive cache: write through > sdc:<4>atkbd.c: Unknown key pressed (translated set 2, code 0x0 on > isa0060/serio0). > atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known. > atkbd.c: Unknown key pressed (translated set 2, code 0x0 on > isa0060/serio0). > atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known. > sdc1 > Attached scsi disk sdc at scsi2, channel 0, id 1, lun 0 > > [root@beowulf scsi]# mount /dev/sdb1 /mnt/ > atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0). > atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known. > ... > atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0). > atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known. > kjournald starting. Commit interval 5 seconds > atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0). > atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known. > EXT3 FS on sdb1, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0). > atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known. > > Best regards > Mile Davidovic, B.Sc. > -- > Mile.Davidovic@xxxxxxxxxxxxxxx > MicronasNIT LLC. > http://www.micronasnit.com > Fruskogorska 11a, 21000 Novi Sad, Serbia & Montenegro > Phone (1) : +381 (0)21 475 00 24 (ext. 111) > Phone (2) : +381 (0)21 475 00 28 (ext. 112) > Fax : +381 (0)21 450 721 >
