Basically the disk is detected, sda is assigned to it, then a error is thrown. It may be as the result of kudzu doing something. If I knew what it was I would try to stop it.
Once the system boots an fdisk /dev/sda fails to find a devices. This is because the modules is not loaded at this point.
The thing is if I reload the module after boot I can fdisk, mkfs and mount the disk.
I am running Fedora core 2 with the latest fedora kernel. The motherboard is a Chaintech Summit SKT600. It is advertised as having SATA with no RAID, although lspci says it has the 6420 controller. Perhaps raid is just turned off. I actually was looking for the nonRAID sata as I prefer the Linux raid.
Below are all the particulars. The lspci output, the initial boot messages for the device and the messages I get when I load the module from the command line. Any suggestions on how I could get the module to stick on boot would be greatly appreciated.
Thank you,
Terrence
uname -a
Linux multi 2.6.7-1.494.2.2 #1 Tue Aug 3 09:39:58 EDT 2004 i686 athlon i386 GNU/Linux
Here is what lspci says about the devices
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
Here is the boot message
Aug 15 09:59:35 multi kernel: SCSI subsystem initialized
Aug 15 09:59:35 multi kernel: libata version 1.02 loaded.
Aug 15 09:59:35 multi kernel: sata_via version 0.20
Aug 15 09:59:35 multi kernel: ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 11 (level, low) -> IRQ 11
Aug 15 09:59:35 multi kernel: sata_via(0000:00:0f.0): routed to hard irq line 11
Aug 15 09:59:35 multi kernel: ata1: SATA max UDMA/133 cmd 0xE200 ctl 0xE302 bmdma 0xE600 irq 11
Aug 15 09:59:36 multi kernel: ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE502 bmdma 0xE608 irq 11
Aug 15 09:59:36 multi kernel: ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01 87:4003 88:407f
Aug 15 09:59:36 multi kernel: ata1: dev 0 ATA, max UDMA/133, 390721968 sectors: lba48
Aug 15 09:59:36 multi kernel: ata1: dev 0 configured for UDMA/133
Aug 15 09:59:36 multi kernel: scsi0 : sata_via
Aug 15 09:59:36 multi kernel: ata2: no device found (phy stat 00000000)
Aug 15 09:59:36 multi kernel: scsi1 : sata_via
Aug 15 09:59:36 multi kernel: Vendor: ATA Model: ST3200822AS Rev: 3.01
Aug 15 09:59:36 multi kernel: Type: Direct-Access ANSI SCSI revision: 05
Aug 15 09:59:36 multi kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
Aug 15 09:59:36 multi kernel: SCSI device sda: drive cache: write back
Aug 15 09:59:36 multi kernel: sda: unknown partition table
Aug 15 09:59:36 multi kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Aug 15 09:59:36 multi kernel: Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Aug 15 09:59:36 multi kernel: kudzu: Using deprecated /dev/sg mechanism instead of SG_IO on the actual device
Aug 15 09:59:36 multi kernel: Synchronizing SCSI cache for disk sda: <4>FAILED
Aug 15 09:59:36 multi kernel: status = 0, message = 00, host = 1, driver = 00
Aug 15 09:59:36 multi kernel:
Here is the command line module load...
Aug 14 22:00:12 multi kernel: libata version 1.02 loaded.
Aug 14 22:00:12 multi kernel: sata_via version 0.20
Aug 14 22:00:12 multi kernel: ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 11 (level, low) -> IRQ 11
Aug 14 22:00:12 multi kernel: sata_via(0000:00:0f.0): routed to hard irq line 11
Aug 14 22:00:12 multi kernel: ata1: SATA max UDMA/133 cmd 0xE200 ctl 0xE302 bmdma 0xE600 irq 11
Aug 14 22:00:12 multi kernel: ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE502 bmdma 0xE608 irq 11
Aug 14 22:00:13 multi kernel: ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01 87:4003 88:407f
Aug 14 22:00:13 multi kernel: ata1: dev 0 ATA, max UDMA/133, 390721968 sectors: lba48
Aug 14 22:00:13 multi kernel: ata1: dev 0 configured for UDMA/133
Aug 14 22:00:13 multi kernel: scsi2 : sata_via
Aug 14 22:00:13 multi kernel: ata2: no device found (phy stat 00000000)
Aug 14 22:00:13 multi kernel: scsi3 : sata_via
Aug 14 22:00:13 multi kernel: Vendor: ATA Model: ST3200822AS Rev: 3.01
Aug 14 22:00:13 multi kernel: Type: Direct-Access ANSI SCSI revision: 05
Aug 14 22:00:13 multi kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
Aug 14 22:00:13 multi kernel: SCSI device sda: drive cache: write back
Aug 14 22:00:13 multi kernel: sda: unknown partition table
Aug 14 22:00:13 multi kernel: Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Aug 14 22:00:13 multi kernel: Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0
Aug 14 22:01:00 multi kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
Aug 14 22:01:00 multi kernel: SCSI device sda: drive cache: write back
Aug 14 22:01:00 multi kernel: sda: sda1
Aug 14 22:01:02 multi kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
Aug 14 22:01:02 multi kernel: SCSI device sda: drive cache: write back
Aug 14 22:01:02 multi kernel: sda: sda1
Aug 14 22:11:24 multi kernel: XFS mounting filesystem sda1
Aug 14 22:11:24 multi kernel: Ending clean XFS mount for filesystem: sda1
Aug 14 22:16:47 multi kernel: spurious 8259A interrupt: IRQ7.
