Hi All on the list,
I'm trying to perform a backup on HP Colorado 8Gb but I was unable to get it working on last FC1 kernel. I've the same problem on another box with an HP Colorado 14Gb, both have the same kernel. I've tested both IDETAPE unit and as expect they are working well on standard LK 2.4.19. Does any one know how can I get it working on FC1 ?
Thanks in advance.
Below there is my dmesg log:
Linux version 2.4.22-1.2197.nptl (bhcompile@xxxxxxxxxxxxxxxxxxxxxxx) (gcc version 3.2.3 20030422 (Red Hat Linux 3.2.3-6)) #1 Thu Jul 1 15:14:28 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fffd000 (usable)
BIOS-e820: 000000000fffd000 - 000000000ffff000 (ACPI data)
BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 65533
zone(0): 4096 pages.
zone(1): 61437 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 00 and too old
You can enable it with acpi=force
ACPI: RSDP (v000 ASUS ) @ 0x000f7980
ACPI: RSDT (v001 ASUS P2B 0x58582e31 ASUS 0x31303030) @ 0x0fffd000
ACPI: FADT (v001 ASUS P2B 0x58582e31 ASUS 0x31303030) @ 0x0fffd080
ACPI: BOOT (v001 ASUS P2B 0x58582e31 ASUS 0x31303030) @ 0x0fffd040
ACPI: DSDT (v001 ASUS P2B 0x00001000 MSFT 0x01000001) @ 0x00000000
Kernel command line: ro root=LABEL=/
Initializing CPU#0
Detected 350.805 MHz processor.
Console: colour VGA+ 80x25
[... snip ...]
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 4D040H2, ATA DISK drive
blk: queue c0402f40, I/O limit 4095Mb (mask 0xffffffff)
hdc: SAMSUNG CD-ROM SC-152G, ATAPI CD/DVD-ROM drive
hdd: HP COLORADO 8GB, ATAPI TAPE drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=4982/255/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3
ide: late registration of driver.[... snip ...]
hdd: attached ide-tape driver.
ide-tape: hdd <-> ht0: HP COLORADO 8GB rev 2.04
ide-tape: hdd: overriding capabilities->speed (assuming 650KB/sec)
ide-tape: hdd: overriding capabilities->max_speed (assuming 650KB/sec)
ide-tape: hdd <-> ht0: 650KBps, 16*32kB buffer, 6336kB pipeline, 100ms tDSC, DMA
ide-tape: Block location is unknown to the tape
ide-tape: Block location is unknown to the tape
ide-tape: ht0: I/O error, pc = 0, key = 4, asc = 40, ascq = b2
ide-tape: ht0: drive not ready
Roberto Fichera.
