Paolo,
Here are the items you requested:
New Disk
========
Disk /dev/had: 30.7GB, 30750031872 bytes
/dev/hda: 255 heads, 63 sectors, 3738 cylinders
Units = cylinders of 16065 * 512 bytes = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 62 497983+ 83 Linux
/dev/hda2 63 3428 27037395 83 Linux
/dev/hda3 3429 3738 2490075 82 Linux swap
Old Disk
========
Disk /dev/hda: 255 heads, 63 sectors, 784 cylinders
Units = cylinders of 16065 * 512 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 13 104391 83 Linux
/dev/hda2 14 719 5670945 83 Linux
/dev/hda3 720 784 522112+ 82 Linux swap
[root@SRINS015 root]#
grub.conf
=========
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this
file
# NOTICE: You have a /boot partition. This means that
# all kernel and initrd paths are relative to /boot/, eg.
# root (hd0,0)
# kernel /vmlinuz-version ro root=/dev/hda2
# initrd /initrd-version.img
#boot=/dev/hda
default=0
timeout=10
splashimage=(hd0,0)/grub/splash.xpm.gz
title Red Hat Linux (2.4.20-28.8)
root (hd0,0)
kernel /vmlinuz-2.4.20-28.8 ro root=LABEL=/
initrd /initrd-2.4.20-28.8.img
title Red Hat Linux (2.4.20-20.8)
root (hd0,0)
kernel /vmlinuz-2.4.20-20.8 ro root=LABEL=/
initrd /initrd-2.4.20-20.8.img
title Red Hat Linux (2.4.20-18.8)
root (hd0,0)
kernel /vmlinuz-2.4.20-18.8 ro root=LABEL=/
initrd /initrd-2.4.20-18.8.img
title Red Hat Linux (2.4.20-13.8)
root (hd0,0)
kernel /vmlinuz-2.4.20-13.8 ro root=LABEL=/
initrd /initrd-2.4.20-13.8.img
title Red Hat Linux (2.4.18-27.8.0)
root (hd0,0)
kernel /vmlinuz-2.4.18-27.8.0 ro root=LABEL=/
initrd /initrd-2.4.18-27.8.0.img
title Red Hat Linux (2.4.18-26.8.0)
root (hd0,0)
kernel /vmlinuz-2.4.18-26.8.0 ro root=LABEL=/
initrd /initrd-2.4.18-26.8.0.img
title Red Hat Linux (2.4.18-24.8.0)
root (hd0,0)
kernel /vmlinuz-2.4.18-24.8.0 ro root=LABEL=/
initrd /initrd-2.4.18-24.8.0.img
title Red Hat Linux (2.4.18-19.8.0)
root (hd0,0)
kernel /vmlinuz-2.4.18-19.8.0 ro root=LABEL=/
initrd /initrd-2.4.18-19.8.0.img
title Red Hat Linux (2.4.18-14)
root (hd0,0)
kernel /vmlinuz-2.4.18-14 ro root=LABEL=/
initrd /initrd-2.4.18-14.img
device.map
==========
[root@SRINS015 grub]# cat device.map
# this device map was generated by anaconda
(fd0) /dev/fd0
(hd0) /dev/hda
Thank you.
John Rumball
>
> John Rumball said:
> > Further to my last post, I was able to mount my partitions from the
> > linux rescue command shell. Although I struggled abit, I was able to
> > run the "grub-install /dev/hda" command successfully. When I
rebooted
> > the machine, this time I get past the GRUB message, but it stops at
> > the "grub>" prompt. Why is it stopping here? My grub.conf looked
good
> > to me. Where do I go from here?
>
> Can you please post your grub.conf, device.map and the output of
fdisk -l ?
>
> Paolo
>
>
> --
> fedora-list mailing list
> fedora-list@xxxxxxxxxx
> To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
>
>
--
