Re: Problems with Aironet 350 card

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Thomas

Many thanks for your time. I should have been more
specific, I'm using a PCMCIA card, not a mini-PCI.

I'll keep looking...
Cheers,
Alex
 
 --- Thomas Munck Steenholdt <tmus@xxxxxxxxxx> wrote:
> > Hi all,
> >
> > I'd be most grateful if someone could provide help
> > with setting this up. I've tried everything and am
> > about to give up...
> >
> > I have it all configured and what seems to fail is
> the
> > DHCP request:
> > Dec 20 14:39:46 localhost kernel: Setting key 0
> > Dec 20 14:39:46 localhost kernel: airo:  WEP_PERM
> set
> > 12106
> > Dec 20 14:39:46 localhost kernel: ip_tables: (C)
> > 2000-2002 Netfilter core team
> > Dec 20 14:39:46 localhost dhclient: wifi0: unknown
> > hardware address type 801
> > Dec 20 14:39:47 localhost dhclient: wifi0: unknown
> > hardware address type 801
> > Dec 20 14:39:49 localhost dhclient: DHCPDISCOVER
> on
> > eth1 to 255.255.255.255 port 67 interval 6
> > Dec 20 14:39:55 localhost dhclient: DHCPDISCOVER
> on
> > eth1 to 255.255.255.255 port 67 interval 16
> > Dec 20 14:40:11 localhost dhclient: DHCPDISCOVER
> on
> > eth1 to 255.255.255.255 port 67 interval 17
> > Dec 20 14:40:28 localhost dhclient: DHCPDISCOVER
> on
> > eth1 to 255.255.255.255 port 67 interval 10
> > Dec 20 14:40:38 localhost dhclient: DHCPDISCOVER
> on
> > eth1 to 255.255.255.255 port 67 interval 10
> > Dec 20 14:40:48 localhost dhclient: DHCPDISCOVER
> on
> > eth1 to 255.255.255.255 port 67 interval 2
> > Dec 20 14:40:50 localhost dhclient: No DHCPOFFERS
> > received.
> >
> > It works on eth0 (network card) and I do know the
> WiFi
> > card works fine under W2K. I have installed the
> Cisco
> > utilities, have used the network configuration
> > utilities, even manually editing the files and
> all's
> > fine! Just that it doesn't work.
> >
> > The funny thing is the card seems to be up, and
> even
> > the interface seems to be up:
> > [root@localhost root]# /sbin/ifconfig eth1
> > eth1      Link encap:Ethernet  HWaddr
> > 00:40:96:41:C4:D0
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500
> > Metric:1
> >           RX packets:0 errors:1023 dropped:0
> > overruns:0 frame:1023
> >           TX packets:12 errors:12 dropped:0
> overruns:0
> > carrier:12
> >           collisions:0 txqueuelen:1000
> >           RX bytes:0 (0.0 b)  TX bytes:3960 (3.8
> Kb)
> >           Interrupt:3 Base address:0x100
> >
> > But it's not.
> >
> > Any help?
> >
> 
> Looks to my like, maybe your WAP key or driver or
> something isn't working
> quite right! You have no packets sent without
> failure and you havn't
> recieved a single byte of data on the interface,
> only a fair amount of
> errors again!
> > RX packets:0 errors:1023 dropped:0 overruns:0
> frame:1023
>              ^        ^^^^
> > TX packets:12 errors:12 dropped:0 overruns:0
> carrier:12
>                        ^^
> There's a couple of things to do AFTER compiling and
> installing the driver!
> 
> 1. Make sure your firmware version i 5.00.01 or
> 5.00.03 those versions are
> the only one that will work with the linux driver...
> I'm using the .01 and
> never tried .03.
> 
> 2. Using the ACU utility, set your adapter up for
> using WAP, then set the
> wap key(will have to be entered as hex values)
> 
> 3. If you want this to work on boot you'll have to
> add a couple of lines
> into your /etc/modules.conf:
> Something like this should work:
> 
> alias eth1 mpi350
> post-install mpi350 /opt/cisco/bin/bcard
> 
> 4. Make sure your eth1 card is set for DHCP... (see
> /etc/sysconfig/network-scripts/ifcfg-eth1)
> 
> 5. Now ifup eth1 and it really should work!!! It
> does for me, and has at
> least in RH9 and FC1 (didn't have and mpi350 before
> RH9)
> 
> On FC1, though - I've installed the airo-mpi driver
> from
> http://bellet.info/~bellet/laptop/
> Check the readme here
> http://bellet.info/~bellet/laptop/airo_mpi.HOWTO.txt
> 
> In my oppinion, the airo-mpi is at least as good and
> stable as the cisco
> driver, and the handeling is linux-standard stuff...
> configuration goes in
> ifcfg-eth1, nothing else... no need to call bcard
> and stuff like that!
> very nice! But both should work!
> 
> Hope it helps!
> 
> Thomas
> 
> 
> --
> fedora-list mailing list
> fedora-list@xxxxxxxxxx
> To unsubscribe:
http://www.redhat.com/mailman/listinfo/fedora-list 

=====
"Beauty is the purgation of superfluities" - Michelangelo

________________________________________________________________________
Want to chat instantly with your online friends?  Get the FREE Yahoo!
Messenger http://mail.messenger.yahoo.co.uk




[Index of Archives]     [Current Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Yosemite News]     [Yosemite Photos]     [KDE Users]     [Fedora Tools]     [Fedora Docs]

  Powered by Linux