Re: x86_64 dynticks not working prev: cpuidle, dynticks compatible or no?

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



System is idle now, previously it was doing something i couldn't halt at the time. I'm looking at "Local timer interrupts" in the "Loc:" section of /proc/interrupts. Across 1 second while the system is pretty much idle, i still get 300 interrupts. My HZ variable is set to 300 in the kernel config, so this is expected but I was under the assumption that dynticks/tickless being compiled in would cause that to be much lower.

Am I reading the wrong section of /proc/interrupts to verify if dynticks is working or not? Again, i see no difference in cpu temp at all.

In case it helps, this is an athlon64 x2 with apic functioning and both cores active in 64bit mode. dmesg is below.
not related :
Some additional notes: it87 is my lm_sensor, it doesn't work in this kernel, yet it did in 2.6.22. Perhaps enabling high precision timers changed something in acpi land.

I enabled tcp dma offloading in this kernel, i get debugging output related to it, error is at the last line. No corruption or otherwise bad behavior. Transferring via cifs at 9.7MB/sec "incoming" took about 15% of one cpu... I never bothered to check if that is the norm but i suspect i'll be removing that feature as it seems to not play nice with the kernel.



kernel: klogd 1.5.0#1, log source = /proc/kmsg started.
) (gcc version 4.2.3 20071123 (prerelease) (Debian 4.2.2-4)) #1 SMP PREEMPT Wed Dec 5 21:49:34 EST 2007
kernel: Command line: root=/dev/sda1 ro console=tty0 libata.atapi_enabled=1
kernel: BIOS-provided physical RAM map:
kernel:  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
kernel:  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
kernel:  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
kernel:  BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
kernel:  BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
kernel:  BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
kernel:  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
kernel:  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
kernel: end_pfn_map = 1048576
kernel: DMI 2.3 present.
kernel: ACPI: RSDP 000F7580, 0014 (r0 Nvidia)
kernel: ACPI: RSDT 7FFF3040, 0034 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) kernel: ACPI: FACP 7FFF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) kernel: ACPI: DSDT 7FFF3180, 65F2 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E)
kernel: ACPI: FACS 7FFF0000, 0040
kernel: ACPI: SSDT 7FFF9880, 0188 (r1 PTLTD POWERNOW 1 LTP 1) kernel: ACPI: MCFG 7FFF9A80, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 0) kernel: ACPI: APIC 7FFF97C0, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
kernel: Zone PFN ranges:
kernel:   DMA             0 ->     4096
kernel:   DMA32        4096 ->  1048576
kernel:   Normal    1048576 ->  1048576
kernel: Movable zone start PFN for each node
kernel: early_node_map[2] active PFN ranges
kernel:     0:        0 ->      159
kernel:     0:      256 ->   524272
kernel: Nvidia board detected. Ignoring ACPI timer override.
kernel: If you got timer trouble try acpi_use_timer_override
kernel: ACPI: PM-Timer IO Port: 0x4008
kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
kernel: Processor #0 (Bootup-CPU)
kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
kernel: Processor #1
kernel: ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
kernel: ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
kernel: ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
kernel: IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
kernel: ACPI: BIOS IRQ0 pin2 override ignored.
kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
kernel: Setting APIC routing to flat
kernel: Using ACPI (MADT) for SMP configuration information
kernel: Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
kernel: SMP: Allowing 2 CPUs, 0 hotplug CPUs
kernel: PERCPU: Allocating 32696 bytes of per cpu data
kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515935 kernel: Kernel command line: root=/dev/sda1 ro console=tty0 libata.atapi_enabled=1
kernel: Initializing CPU#0
kernel: PID hash table entries: 4096 (order: 12, 32768 bytes)
kernel: TSC calibrated against PM_TIMER
kernel: Marking TSC unstable due to TSCs unsynchronized
kernel: time.c: Detected 2010.305 MHz processor.
kernel: Console: colour VGA+ 80x25
kernel: console [tty0] enabled
kernel: Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
kernel: Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
kernel: Checking aperture...
kernel: CPU 0: aperture @ 8640000000 size 32 MB
kernel: No AGP bridge found
kernel: Memory: 2059736k/2097088k available (2695k kernel code, 36256k reserved, 1069k data, 204k init) kernel: SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 kernel: Calibrating delay using timer specific routine.. 4023.79 BogoMIPS (lpj=6703675)
kernel: Mount-cache hash table entries: 256
kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
kernel: CPU: L2 Cache: 512K (64 bytes/line)
kernel: CPU: Physical Processor ID: 0
kernel: CPU: Processor Core ID: 0
kernel: SMP alternatives: switching to UP code
kernel: ACPI: Core revision 20070126
kernel: Using local APIC timer interrupts.
kernel: Detected 12.564 MHz APIC timer.
kernel: SMP alternatives: switching to SMP code
kernel: Booting processor 1/2 APIC 0x1
kernel: Initializing CPU#1
kernel: Calibrating delay using timer specific routine.. 4022.15 BogoMIPS (lpj=6701043)
kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
kernel: CPU: L2 Cache: 512K (64 bytes/line)
kernel: CPU: Physical Processor ID: 0
kernel: CPU: Processor Core ID: 1
kernel: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
kernel: Brought up 2 CPUs
kernel: net_namespace: 176 bytes
kernel: NET: Registered protocol family 16
kernel: ACPI: bus type pci registered
kernel: PCI: Using configuration type 1
kernel: ACPI: Interpreter enabled
kernel: ACPI: (supports S0 S5)
kernel: ACPI: Using IOAPIC for interrupt routing
kernel: PCI: MCFG configuration 0: base 3758096384 segment 0 buses 0 - 255
kernel: PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
kernel: PCI: Using MMCONFIG at e0000000 - efffffff
kernel: PCI: No mmconfig possible on device 00:18
kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
kernel: PCI: Transparent bridge - 0000:00:09.0
kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
kernel: ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 *10 11 12 14 15)
kernel: ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
kernel: ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 *7 9 10 11 12 14 15)
kernel: ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 7 9 10 11 12 14 15)
kernel: ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. kernel: ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
kernel: ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15)
kernel: ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
kernel: ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
kernel: ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
kernel: ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
kernel: ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
kernel: ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
kernel: ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
kernel: pnp: PnP ACPI init
kernel: ACPI: bus type pnp registered
kernel: pnp: PnP ACPI: found 9 devices
kernel: ACPI: ACPI bus type pnp unregistered
kernel: SCSI subsystem initialized
kernel: usbcore: registered new interface driver usbfs
kernel: usbcore: registered new interface driver hub
kernel: usbcore: registered new device driver usb
kernel: PCI: Using ACPI for IRQ routing
kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
kernel: ACPI: RTC can wake from S4
kernel: system 00:01: ioport range 0x4000-0x407f has been reserved
kernel: system 00:01: ioport range 0x4080-0x40ff has been reserved
kernel: system 00:01: ioport range 0x4400-0x447f has been reserved
kernel: system 00:01: ioport range 0x4480-0x44ff has been reserved
kernel: system 00:01: ioport range 0x4800-0x487f has been reserved
kernel: system 00:01: ioport range 0x4880-0x48ff has been reserved
kernel: system 00:02: ioport range 0x4d0-0x4d1 has been reserved
kernel: system 00:02: ioport range 0x800-0x87f has been reserved
kernel: system 00:02: ioport range 0x290-0x297 has been reserved
kernel: system 00:07: iomem range 0xe0000000-0xefffffff could not be reserved
kernel: system 00:08: iomem range 0xf0000-0xf3fff could not be reserved
kernel: system 00:08: iomem range 0xf4000-0xf7fff could not be reserved
kernel: system 00:08: iomem range 0xf8000-0xfbfff could not be reserved
kernel: system 00:08: iomem range 0xfc000-0xfffff could not be reserved
kernel: system 00:08: iomem range 0x7fff0000-0x7fffffff could not be reserved
kernel: system 00:08: iomem range 0xffff0000-0xffffffff has been reserved
kernel: system 00:08: iomem range 0x0-0x9ffff could not be reserved
kernel: system 00:08: iomem range 0x100000-0x7ffeffff could not be reserved
kernel: system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
kernel: system 00:08: iomem range 0xfee00000-0xfeefffff could not be reserved
kernel: system 00:08: iomem range 0xfefff000-0xfeffffff has been reserved
kernel: system 00:08: iomem range 0xfff80000-0xfff80fff has been reserved
kernel: PCI: Bridge: 0000:00:09.0
kernel:   IO window: disabled.
kernel:   MEM window: disabled.
kernel:   PREFETCH window: c8000000-c80fffff
kernel: PCI: Bridge: 0000:00:0b.0
kernel:   IO window: disabled.
kernel:   MEM window: disabled.
kernel:   PREFETCH window: disabled.
kernel: PCI: Bridge: 0000:00:0c.0
kernel:   IO window: disabled.
kernel:   MEM window: disabled.
kernel:   PREFETCH window: disabled.
kernel: PCI: Bridge: 0000:00:0d.0
kernel:   IO window: disabled.
kernel:   MEM window: disabled.
kernel:   PREFETCH window: disabled.
kernel: PCI: Bridge: 0000:00:0e.0
kernel:   IO window: disabled.
kernel:   MEM window: c0000000-c7ffffff
kernel:   PREFETCH window: b0000000-bfffffff
kernel: NET: Registered protocol family 2
kernel: Time: acpi_pm clocksource has been installed.
kernel: IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
kernel: TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
kernel: TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
kernel: TCP: Hash tables configured (established 262144 bind 65536)
kernel: TCP reno registered
kernel: fuse init (API version 7.9)
kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
kernel: io scheduler noop registered
kernel: io scheduler cfq registered (default)
kernel: PCI: Found disabled HT MSI Mapping on 0000:00:0b.0
kernel: PCI: Found enabled HT MSI Mapping on 0000:00:00.0
kernel: PCI: Linking AER extended capability on 0000:00:0b.0
kernel: PCI: Found disabled HT MSI Mapping on 0000:00:0c.0
kernel: PCI: Found enabled HT MSI Mapping on 0000:00:00.0
kernel: PCI: Linking AER extended capability on 0000:00:0c.0
kernel: PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
kernel: PCI: Found enabled HT MSI Mapping on 0000:00:00.0
kernel: PCI: Linking AER extended capability on 0000:00:0d.0
kernel: PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
kernel: PCI: Found enabled HT MSI Mapping on 0000:00:00.0
kernel: PCI: Linking AER extended capability on 0000:00:0e.0
kernel: assign_interrupt_mode Found MSI capability
last message repeated 3 times
kernel: ACPI: Thermal Zone [THRM] (40 C)
kernel: Real Time Clock Driver v1.12ac
kernel: Linux agpgart interface v0.103
kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
kernel: ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
kernel: ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23 kernel: forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x5043 @ 9, addr 00:13:d4:d4:66:e8
kernel: forcedeth 0000:00:0a.0: highdma csum timirq gbit lnktim desc-v3
kernel: ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
kernel: ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22
kernel: sata_nv 0000:00:08.0: Using ADMA mode
kernel: scsi0 : sata_nv
kernel: scsi1 : sata_nv
kernel: ata1: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xd400 irq 22
kernel: ata2: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xd408 irq 22
kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
kernel: ata1.00: ATA-7: Maxtor 6L200S0, BACE1G10, max UDMA/133
kernel: ata1.00: 398297088 sectors, multi 1: LBA48 NCQ (depth 31/32)
kernel: ata1.00: configured for UDMA/133
kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
kernel: ata2.00: ATA-7: Maxtor 6L200S0, BACE1G10, max UDMA/133
kernel: ata2.00: 398297088 sectors, multi 1: LBA48 NCQ (depth 31/32)
kernel: ata2.00: configured for UDMA/133
kernel: scsi 0:0:0:0: Direct-Access ATA Maxtor 6L200S0 BACE PQ: 0 ANSI: 5 kernel: ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
kernel: sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
kernel: sd 0:0:0:0: [sda] Write Protect is off
kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel: sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
kernel: sd 0:0:0:0: [sda] Write Protect is off
kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel:  sda: sda1 sda2
kernel: sd 0:0:0:0: [sda] Attached SCSI disk
kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
kernel: scsi 1:0:0:0: Direct-Access ATA Maxtor 6L200S0 BACE PQ: 0 ANSI: 5 kernel: ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
kernel: sd 1:0:0:0: [sdb] 398297088 512-byte hardware sectors (203928 MB)
kernel: sd 1:0:0:0: [sdb] Write Protect is off
kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel: sd 1:0:0:0: [sdb] 398297088 512-byte hardware sectors (203928 MB)
kernel: sd 1:0:0:0: [sdb] Write Protect is off
kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel:  sdb: sdb1 sdb2
kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0
kernel: scsi2 : pata_amd
kernel: scsi3 : pata_amd
kernel: ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
kernel: ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
kernel: ata3.00: ATA-7: Maxtor 6Y120P0, YAR41VW0, max UDMA/133
kernel: ata3.00: 240121728 sectors, multi 1: LBA
kernel: ata3.00: configured for UDMA/133
kernel: ata4.00: ATAPI: PLEXTOR DVDR   PX-712A, 1.09, max MWDMA2
kernel: ata4.00: configured for MWDMA2
kernel: scsi 2:0:0:0: Direct-Access ATA Maxtor 6Y120P0 YAR4 PQ: 0 ANSI: 5
kernel: sd 2:0:0:0: [sdc] 240121728 512-byte hardware sectors (122942 MB)
kernel: sd 2:0:0:0: [sdc] Write Protect is off
kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel: sd 2:0:0:0: [sdc] 240121728 512-byte hardware sectors (122942 MB)
kernel: sd 2:0:0:0: [sdc] Write Protect is off
kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel:  sdc: sdc1
kernel: sd 2:0:0:0: [sdc] Attached SCSI disk
kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0
kernel: scsi 3:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.09 PQ: 0 ANSI: 5
kernel: sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
kernel: Uniform CD-ROM driver Revision: 3.20
kernel: sr 3:0:0:0: Attached scsi generic sg3 type 5
kernel: ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
kernel: ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 21 (level, low) -> IRQ 21
kernel: ehci_hcd 0000:00:02.1: EHCI Host Controller
kernel: ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
kernel: ehci_hcd 0000:00:02.1: debug port 1
kernel: ehci_hcd 0000:00:02.1: irq 21, io mem 0xfeb00000
kernel: ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
kernel: usb usb1: configuration #1 chosen from 1 choice
kernel: hub 1-0:1.0: USB hub found
kernel: hub 1-0:1.0: 10 ports detected
kernel: ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
kernel: ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, low) -> IRQ 20
kernel: ohci_hcd 0000:00:02.0: OHCI Host Controller
kernel: ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
kernel: ohci_hcd 0000:00:02.0: irq 20, io mem 0xc8103000
kernel: usb usb2: configuration #1 chosen from 1 choice
kernel: hub 2-0:1.0: USB hub found
kernel: hub 2-0:1.0: 10 ports detected
kernel: PNP: No PS/2 controller found. Probing ports directly.
kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
kernel: mice: PS/2 mouse device common for all mice
kernel: rtc_cmos: probe of 00:04 failed with error -16
kernel: Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
kernel: md: raid0 personality registered for level 0
kernel: cpuidle: using governor ladder
kernel: cpuidle: using governor menu
kernel: usb 2-2: new low speed USB device using ohci_hcd and address 2
kernel: usb 2-2: configuration #1 chosen from 1 choice
kernel: usb 2-4: new low speed USB device using ohci_hcd and address 3
kernel: usb 2-4: configuration #1 chosen from 1 choice
kernel: input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input0 kernel: input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:02.0-2 kernel: input: HID 1267:0103 as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input1
kernel: input: USB HID v1.10 Keyboard [HID 1267:0103] on usb-0000:00:02.0-4
kernel: input: HID 1267:0103 as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.1/input/input2
kernel: input: USB HID v1.10 Device [HID 1267:0103] on usb-0000:00:02.0-4
kernel: usbcore: registered new interface driver usbhid
kernel: drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
kernel: Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC).
kernel: ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 23
kernel: ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 23 (level, low) -> IRQ 23
kernel: intel8x0_measure_ac97_clock: measured 49914 usecs
kernel: intel8x0: clocking to 46825
kernel: ALSA device list:
kernel:   #0: NVidia CK804 with ALC850 at irq 23
kernel: TCP cubic registered
kernel: powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ processors (2 cpu cores) (version 2.20.00)
kernel: powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x8
kernel: powernow-k8:    1 : fid 0xa (1800 MHz), vid 0xa
kernel: powernow-k8:    2 : fid 0x2 (1000 MHz), vid 0x12
kernel: drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
kernel: md: Autodetecting RAID arrays.
kernel: md: Scanned 2 and added 2 devices.
kernel: md: autorun ...
kernel: md: considering sdb2 ...
kernel: md:  adding sdb2 ...
kernel: md:  adding sda2 ...
kernel: md: created md0
kernel: md: bind<sda2>
kernel: md: bind<sdb2>
kernel: md: running: <sdb2><sda2>
kernel: md0: setting max_sectors to 128, segment boundary to 32767
kernel: raid0: looking at sdb2
kernel: raid0:   comparing sdb2(195237824) with sdb2(195237824)
kernel: raid0:   END
kernel: raid0:   ==> UNIQUE
kernel: raid0: 1 zones
kernel: raid0: looking at sda2
kernel: raid0:   comparing sda2(195237824) with sdb2(195237824)
kernel: raid0:   EQUAL
kernel: raid0: FINAL 1 zones
kernel: raid0: done.
kernel: raid0 : md_size is 390475648 blocks.
kernel: raid0 : conf->hash_spacing is 390475648 blocks.
kernel: raid0 : nb_zone is 1.
kernel: raid0 : Allocating 8 bytes for hash.
kernel: md: ... autorun DONE.
kernel: kjournald starting.  Commit interval 5 seconds
kernel: EXT3-fs: mounted filesystem with ordered data mode.
kernel: VFS: Mounted root (ext3 filesystem) readonly.
kernel: Freeing unused kernel memory: 204k freed
kernel: NET: Registered protocol family 1
kernel: i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
kernel: i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
kernel: EXT3 FS on sda1, internal journal
kernel: it87: Found IT8712F chip at 0x290, revision 7
kernel: it87: in3 is VCC (+5V)
kernel: it87: in7 is VCCH (+5V Stand-By)
kernel: ACPI: Device needs an ACPI driver
kernel: kjournald starting.  Commit interval 5 seconds
kernel: EXT3 FS on sdb1, internal journal
kernel: EXT3-fs: mounted filesystem with ordered data mode.
kernel: kjournald starting.  Commit interval 5 seconds
kernel: EXT3 FS on md0, internal journal
kernel: EXT3-fs: mounted filesystem with ordered data mode.
kernel: kjournald starting.  Commit interval 5 seconds
kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kernel: EXT3 FS on sdc1, internal journal
kernel: EXT3-fs: mounted filesystem with ordered data mode.
kernel: eth0: no link during initialization.
kernel: eth0: link up.
lpd[3227]: restarted
kernel: warning: `ntpd' uses 32-bit capabilities (legacy support in use)
kernel: Clocksource tsc unstable (delta = -76657464 ns)
kernel: warning: process `nvidia-installe' used the deprecated sysctl system call with 1.23. kernel: warning: process `nvidia-installe' used the deprecated sysctl system call with 1.23.
kernel: nvidia: module license 'NVIDIA' taints kernel.
kernel: ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
kernel: ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 kernel: NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007 kernel: warning: process `nvidia-installe' used the deprecated sysctl system call with 1.23.
kernel: WARNING: at net/ipv4/tcp_input.c:2518 tcp_fastretrans_alert()

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux