Re: wrong NUMA detection on HP385 G2

[Pavel Krauz <krauz@cncz.cz>]

>> my HP 385 G2 - 2x dual core Opteron 2216 running 2.6.23.1 with NUMA support says the following: 
>
> Can you post a full boot log? 

Here it is.

Further I have a problem with booting the kernel on 4x dual core Opteron (HP585). It prints lot of panics on boot to console but not to the log. (without NUMA support it boots OK).
If you tell me how to get the first panic message I will sent it to you.

On HP385 booted with mem=3072M when I try to bind a program to node1 the kernel panics - again there are lots of messages. With 4GB it runs OK.

b.r.
Pavel

Linux version 2.6.23.1 (root@tcom.domain.local) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #2 SMP Thu Nov 15 10:31:53 CET 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
 BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000cfe50000 (usable)
 BIOS-e820: 00000000cfe50000 - 00000000cfe58000 (ACPI data)
 BIOS-e820: 00000000cfe58000 - 00000000d0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 000000012ffff000 (usable)
Node: 0, start_pfn: 0, end_pfn: 159
  Setting physnode_map array to node 0 for pfns:
  0 
Node: 0, start_pfn: 256, end_pfn: 851536
  Setting physnode_map array to node 0 for pfns:
  256 65792 131328 196864 262400 327936 393472 459008 524544 590080 655616 721152 786688 
Node: 0, start_pfn: 1048576, end_pfn: 1245183
  Setting physnode_map array to node 0 for pfns:
  1048576 1114112 1179648 
get_memcfg_from_srat: assigning address to rsdp
RSD PTR  v2 [HP    ]
Begin SRAT table scan....
CPU 0x00 in proximity domain 0x00
CPU 0x01 in proximity domain 0x00
Memory range 0x0 to 0xA0 (type 0x1) in proximity domain 0x00 enabled
Memory range 0x100 to 0x80000 (type 0x1) in proximity domain 0x00 enabled
CPU 0x02 in proximity domain 0x01
CPU 0x03 in proximity domain 0x01
Memory range 0x80000 to 0xD0000 (type 0x1) in proximity domain 0x01 enabled
Memory range 0x100000 to 0x130000 (type 0x1) in proximity domain 0x01 enabled
acpi20_parse_srat: Entry length value is zero; can't parse any further!
pxm bitmap: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
Number of logical nodes in system = 2
Number of memory chunks in system = 4
chunk 0 nid 0 start_pfn 00000000 end_pfn 000000a0
Entering add_active_range(0, 0, 160) 0 entries of 256 used
chunk 1 nid 0 start_pfn 00000100 end_pfn 00080000
Entering add_active_range(0, 256, 524288) 1 entries of 256 used
chunk 2 nid 1 start_pfn 00080000 end_pfn 000d0000
Entering add_active_range(1, 524288, 851968) 2 entries of 256 used
chunk 3 nid 1 start_pfn 00100000 end_pfn 00130000
Entering add_active_range(1, 1048576, 1245184) 3 entries of 256 used
Node: 0, start_pfn: 0, end_pfn: 524288
  Setting physnode_map array to node 0 for pfns:
  0 65536 131072 196608 262144 327680 393216 458752 
Node: 1, start_pfn: 524288, end_pfn: 1245184
  Setting physnode_map array to node 1 for pfns:
  524288 589824 655360 720896 786432 851968 917504 983040 1048576 1114112 1179648 
Reserving 4608 pages of KVA for lmem_map of node 0
Shrinking node 0 from 524288 pages to 519680 pages
Reserving 6144 pages of KVA for lmem_map of node 1
Shrinking node 1 from 1245183 pages to 1239039 pages
Shrinking node 1 further by 511 pages for proper alignment
Reserving total of 10752 pages for numa KVA remap
kva_start_pfn ~ 218112 find_max_low_pfn() ~ 229376
max_pfn = 1245183
3967MB HIGHMEM available.
896MB LOWMEM available.
min_low_pfn = 2158, max_low_pfn = 229376, highstart_pfn = 229376
Low memory ends at vaddr f8000000
node 0 will remap to vaddr f5400000 - f9200000
node 1 will remap to vaddr f6600000 - faa00000
High memory starts at vaddr f8000000
found SMP MP-table at 000f4f80
NX (Execute Disable) protection: active
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->  1245183
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0:        0 ->      160
    0:      256 ->   519680
    1:   524288 ->   851968
    1:  1048576 ->  1238528
On node 0 totalpages: 519584
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3968 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 2268 pages used for memmap
  HighMem zone: 288036 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
On node 1 totalpages: 517632
  DMA zone: 0 pages used for memmap
  Normal zone: 0 pages used for memmap
  HighMem zone: 5580 pages used for memmap
  HighMem zone: 512052 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F4F00, 0024 (r2 HP    )
ACPI: XSDT CFE50780, 005C (r1 HP     A09             2   Ò     162E)
ACPI: FACP CFE50800, 00F4 (r3 HP     A09             2   Ò     162E)
ACPI: DSDT CFE50900, 4D3B (r1 HP         DSDT        1 INTL 20030228)
ACPI: FACS CFE50100, 0040
ACPI: SPCR CFE50140, 0050 (r1 HP     SPCRRBSU        1   Ò     162E)
ACPI: MCFG CFE501C0, 003C (r1 HP     ProLiant        1             0)
ACPI: HPET CFE50200, 0038 (r1 HP     A09             2   Ò     162E)
ACPI: SPMI CFE50240, 0040 (r5 HP     ProLiant        1   Ò     162E)
ACPI: APIC CFE50280, 00EA (r1 HP     00000083        2             0)
ACPI: SRAT CFE50380, 0110 (r1 AMD    HAMMER          1 AMD         1)
ACPI: PM-Timer IO Port: 0x920
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 15:1 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x09] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 9, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x0a] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 10, version 17, address 0xfec02000, GSI 32-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 3 I/O APICs
ACPI: HPET id: 0x1166a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d4000000 (gap: d0000000:2ec00000)
Built 2 zonelists in Zone order.  Total pages: 1027576
Policy zone: HighMem
Kernel command line: ro root=LABEL=/
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec01000)
mapped IOAPIC to ffff8000 (fec02000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07e3000 soft=c07c3000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2400.147 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Initializing HighMem for node 0 (00038000:0007ee00)
Initializing HighMem for node 1 (00080000:0012e600)
Memory: 4097176k/4980732k available (2420k kernel code, 49956k reserved, 1132k data, 264k init, 3230016k highmem)
virtual kernel memory layout:
    fixmap  : 0xffc54000 - 0xfffff000   (3756 kB)
    pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
    vmalloc : 0xf8800000 - 0xff9fe000   ( 113 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc077e000 - 0xc07c0000   ( 264 kB)
      .data : 0xc065d2d8 - 0xc07786a4   (1132 kB)
      .text : 0xc0400000 - 0xc065d2d8   (2420 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Calibrating delay using timer specific routine.. 4802.71 BogoMIPS (lpj=2401359)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Core 0
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: AMD Dual-Core AMD Opteron(tm) Processor 2216 HE stepping 03
Mapping cpu 0 to node 0
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07e4000 soft=c07c4000
Initializing CPU#1
Mapping cpu 1 to node 0
Calibrating delay using timer specific routine.. 4800.20 BogoMIPS (lpj=2400101)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Core 1
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Dual-Core AMD Opteron(tm) Processor 2216 HE stepping 03
SMP alternatives: switching to SMP code
Booting processor 2/2 eip 3000
CPU 2 irqstacks, hard=c07e5000 soft=c07c5000
Initializing CPU#2
Mapping cpu 2 to node 0
Calibrating delay using timer specific routine.. 4800.35 BogoMIPS (lpj=2400178)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2(2) -> Core 0
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: AMD Dual-Core AMD Opteron(tm) Processor 2216 HE stepping 03
SMP alternatives: switching to SMP code
Booting processor 3/3 eip 3000
CPU 3 irqstacks, hard=c07e6000 soft=c07c6000
Initializing CPU#3
Mapping cpu 3 to node 0
Calibrating delay using timer specific routine.. 4800.12 BogoMIPS (lpj=2400061)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3(2) -> Core 1
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: AMD Dual-Core AMD Opteron(tm) Processor 2216 HE stepping 03
Total of 4 processors activated (19203.39 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 4 CPUs
khelper used greatest stack depth: 3264 bytes left
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at d0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0072, last bus=74
PCI: Using configuration type 1
Setting up standard PCI resources
khelper used greatest stack depth: 3152 bytes left
ACPI: EC: Look up EC in DSDT
ACPI: SSDT CFE58000, 046C (r2 HP     PNOWSSDT        2 HP          1)
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: PXH quirk detected, disabling MSI for SHPC device
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXB0.PXH0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXB1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXB4._PRT]
ACPI: PCI Root Bridge [PCI1] (0000:40)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.EXBA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.EXBB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.EXBD._PRT]
ACPI: PCI Interrupt Link [IUSB] (IRQs *5)
ACPI: PCI Interrupt Link [IN00] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN01] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN02] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN03] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN04] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN05] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN06] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN07] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN08] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN09] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN10] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN11] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN12] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN13] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN14] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN15] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN16] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN17] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN18] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN19] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN20] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN21] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN22] (IRQs 7 *10 11)
ACPI: PCI Interrupt Link [IN23] (IRQs *7 10 11)
ACPI: PCI Interrupt Link [IN24] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN25] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN26] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN27] (IRQs 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [IN28] (IRQs *7 10 11)
ACPI: PCI Interrupt Link [IN29] (IRQs 7 10 *11)
ACPI: PCI Interrupt Link [IN30] (IRQs 7 *10 11)
ACPI: PCI Interrupt Link [IN31] (IRQs 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
Time: hpet clocksource has been installed.
pnp: 00:01: ioport range 0x408-0x40f has been reserved
pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:01: iomem range 0xd0000000-0xdfffffff has been reserved
PCI: Bridge: 0000:01:0d.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:05:00.0
  IO window: disabled.
  MEM window: f9e00000-f9ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0f.0
  IO window: disabled.
  MEM window: f9d00000-f9ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:10.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:11.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:12.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:03:00.0
  IO window: disabled.
  MEM window: f6000000-f7ffffff
  PREFETCH window: e0000000-e00fffff
PCI: Bridge: 0000:00:13.0
  IO window: disabled.
  MEM window: f6000000-f7ffffff
  PREFETCH window: e0000000-e00fffff
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 42 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0f.0 to 64
PCI: Setting latency timer of device 0000:05:00.0 to 64
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 38 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:10.0 to 64
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 39 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:11.0 to 64
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 40 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:12.0 to 64
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 41 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:13.0 to 64
PCI: Setting latency timer of device 0000:03:00.0 to 64
PCI: Bridge: 0000:40:0f.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:40:10.0
  IO window: 4000-4fff
  MEM window: fde00000-fdffffff
  PREFETCH window: e0200000-e02fffff
PCI: Bridge: 0000:40:11.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:41:00.0
  IO window: disabled.
  MEM window: fa000000-fbffffff
  PREFETCH window: e0300000-e03fffff
PCI: Bridge: 0000:40:12.0
  IO window: disabled.
  MEM window: fa000000-fbffffff
  PREFETCH window: e0300000-e03fffff
PCI: Bridge: 0000:40:13.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:40:0f.0[A] -> GSI 36 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:40:0f.0 to 64
ACPI: PCI Interrupt 0000:40:10.0[A] -> GSI 32 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:40:10.0 to 64
ACPI: PCI Interrupt 0000:40:11.0[A] -> GSI 33 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:40:11.0 to 64
ACPI: PCI Interrupt 0000:40:12.0[A] -> GSI 34 (level, low) -> IRQ 24
PCI: Setting latency timer of device 0000:40:12.0 to 64
PCI: Setting latency timer of device 0000:41:00.0 to 64
ACPI: PCI Interrupt 0000:40:13.0[A] -> GSI 35 (level, low) -> IRQ 25
PCI: Setting latency timer of device 0000:40:13.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1280k freed
khelper used greatest stack depth: 3084 bytes left
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1195568280.526:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:03.0
pci 0000:00:04.4: HCRESET not completed yet!
PCI: MSI quirk detected. MSI deactivated.
PCI: Setting latency timer of device 0000:00:0f.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0f.0:pcie00]
PCI: Setting latency timer of device 0000:00:10.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:10.0:pcie00]
PCI: Setting latency timer of device 0000:00:11.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:11.0:pcie00]
PCI: Setting latency timer of device 0000:00:12.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:12.0:pcie00]
PCI: Setting latency timer of device 0000:00:13.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:13.0:pcie00]
PCI: Setting latency timer of device 0000:40:0f.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:40:0f.0:pcie00]
PCI: Setting latency timer of device 0000:40:10.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:40:10.0:pcie00]
PCI: Setting latency timer of device 0000:40:11.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:40:11.0:pcie00]
PCI: Setting latency timer of device 0000:40:12.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:40:12.0:pcie00]
PCI: Setting latency timer of device 0000:40:13.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:40:13.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0818): AE_NOT_FOUND, Processor Device is not present [20070126]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
ACPI: PCI Interrupt 0000:46:00.0[A] -> GSI 32 (level, low) -> IRQ 22
cciss: MSI-X init failed -22
cciss0: <0x3230> at PCI 0000:46:00.0 IRQ 22 using DAC
      blocks= 286677120 block_size= 512
      heads=255, sectors=32, cylinders=35132

      blocks= 286677120 block_size= 512
      heads=255, sectors=32, cylinders=35132

 cciss/c0d0: p1 p2
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.6.5 (September 20, 2007)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 41 (level, low) -> IRQ 20
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f6000000, IRQ 20, node addr 001cc456bda2
ACPI: PCI Interrupt 0000:42:00.0[A] -> GSI 34 (level, low) -> IRQ 24
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 24, node addr 001cc456bda0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks HT1000: IDE controller at PCI slot 0000:00:06.1
SvrWks HT1000: chipset revision 0
SvrWks HT1000: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1840-0x1847, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
hda: TEAC DV-W28ECW, ATAPI CD/DVD-ROM drive
hda: selected mode 0x22
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 Dual-Core AMD Opteron(tm) Processor 2216 HE processors (4 cpu cores) (version 2.00.00)
powernow-k8:    0 : fid 0x10 (2400 MHz), vid 0xc
powernow-k8:    1 : fid 0xe (2200 MHz), vid 0xe
powernow-k8:    2 : fid 0xc (2000 MHz), vid 0x10
powernow-k8:    3 : fid 0xa (1800 MHz), vid 0x10
powernow-k8:    4 : fid 0x2 (1000 MHz), vid 0x12
powernow-k8:    0 : fid 0x10 (2400 MHz), vid 0xc
powernow-k8:    1 : fid 0xe (2200 MHz), vid 0xe
powernow-k8:    2 : fid 0xc (2000 MHz), vid 0x10
powernow-k8:    3 : fid 0xa (1800 MHz), vid 0x10
powernow-k8:    4 : fid 0x2 (1000 MHz), vid 0x12
Using IPI No-Shortcut mode
Freeing unused kernel memory: 264k freed
Write protecting the kernel read-only data: 783k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:04.4[B] -> GSI 45 (level, low) -> IRQ 26
uhci_hcd 0000:00:04.4: UHCI Host Controller
uhci_hcd 0000:00:04.4: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:04.4: port count misdetected? forcing to 2 ports
uhci_hcd 0000:00:04.4: HCRESET not completed yet!
uhci_hcd 0000:00:04.4: irq 26, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
insmod used greatest stack depth: 2440 bytes left
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [IUSB] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [IUSB] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:07.0: OHCI Host Controller
ohci_hcd 0000:00:07.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:07.0: irq 5, io mem 0xf5ee0000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.1[A] -> Link [IUSB] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:07.1: OHCI Host Controller
ohci_hcd 0000:00:07.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:07.1: irq 5, io mem 0xf5ed0000
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: PS/2 Generic Mouse as /class/input/input1
insmod used greatest stack depth: 2368 bytes left
ACPI: PCI Interrupt 0000:00:07.2[A] -> Link [IUSB] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:07.2: EHCI Host Controller
ehci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:07.2: irq 5, io mem 0xf5ec0000
ehci_hcd 0000:00:07.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
usb 1-1: configuration #1 chosen from 1 choice
input: HP Virtual Keyboard as /class/input/input2
input: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:00:04.4-1
input: HP Virtual Keyboard as /class/input/input3
input: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:00:04.4-1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-2: new full speed USB device using uhci_hcd and address 3
audit(1195568284.624:2): enforcing=1 old_enforcing=0 auid=4294967295
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 7 ports detected
security:  3 users, 6 roles, 1587 types, 172 bools, 1 sens, 1024 cats
security:  59 classes, 49762 rules
security:  class dccp_socket not defined in policy
security:  class memprotect not defined in policy
security:  permission dccp_recv in class node not defined in policy
security:  permission dccp_send in class node not defined in policy
security:  permission dccp_recv in class netif not defined in policy
security:  permission dccp_send in class netif not defined in policy
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev cciss/c0d0p1, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1195568284.819:3): policy loaded auid=4294967295
hostname used greatest stack depth: 2180 bytes left
uname used greatest stack depth: 2080 bytes left
mount used greatest stack depth: 1376 bytes left
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: not running at top speed; connect to a high speed hub
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ipmi message handler version 39.1
IPMI System Interface driver.
ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
piix4_smbus 0000:00:06.0: Found 0000:00:06.0 device
Floppy drive(s): fd0 is 1.44M
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
ipmi: Found new BMC (man_id: 0x00000b,  prod_id: 0x0000, dev_id: 0x11)
IPMI kcs interface initialized
ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
ipmi_si: duplicate interface
ACPI: PCI Interrupt 0000:00:04.6[A] -> GSI 46 (level, low) -> IRQ 27
ipmi_si: Trying PCI-specified kcs state machine at mem address 0xf5ef0000, slave address 0x0, irq 27
  Using irq 27
ipmi: interfacing existing BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11)
IPMI kcs interface initialized
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
lp: driver loaded but no devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
EXT3 FS on cciss/c0d0p1, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 4096564k swap on /dev/cciss/c0d0p2.  Priority:-1 extents:1 across:4096564k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
rc.sysinit used greatest stack depth: 1192 bytes left
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
Clocksource tsc unstable (delta = -254144931 ns)
ADDRCONF(NETDEV_UP): eth0: link is not ready
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
bnx2: eth1 NIC Copper Link is Up, 1000 Mbps full duplex
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
audit(1195568307.893:4): audit_pid=2804 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
eth0: no IPv6 routers present
eth1: no IPv6 routers present
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts

Attachment: .config.gz
Description: GNU Zip compressed data