Hi, thanks for the reply. :)
Bartlomiej Zolnierkiewicz wrote:
Hi,
On Monday 12 November 2007, Andrew Morton wrote:
On Fri, 09 Nov 2007 11:22:41 +0100 Jonas Stare <[email protected]> wrote:
Hi.
This week I ran into a strange hardware problem. During boot I got a 35
second delay while waiting for IDE-disks that weren't there to report
With what chipset and host driver does this happen?
I am not sure about the chip-set but I think it was vt82c686b. It used
the via82cxxx-driver, but only _after_ using the generic ide-code to
probe/wait (a long time) for the disks. (This was in Suse 10.1 SP 1.)
that they were not in a BSY state. The problem was most likely in the
hardware but this patch enables you to ignore waiting for disks by
setting hdX=noprobe (and not setting the geometry by hand) as a kernel
option.
If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for that
drive. Even if there would be a drive there and it is still BSY
afterwards it should not matter since it isn't probed for later.
There are other ways to get around the "35-seconds-of-waiting-in-vain",
like actually fix the hardware, insert a second drive that works or
recompile the kernel with edd-support builtin (atleast I've seen that
solution on a forum) and possibly others. But this patch would allow
people to get Linux to boot quickly on wonky hardware without having to
recompile anything.
(The code also honors the MAX_DRIVES variable instead of assuming that
ther will be 2 drives on the bus.)
I keep on hearing about problems with boot-time IDE probing. It's public
enemy #1 with the embedded guys.
The problem is that we are not hearing about them.
Please forward the reports to [email protected].
It does seem that operator intervention is needed in some fashion.
I will be happy for all the comments I can get. :) But be gentle, this
is my first patch...
Jonas, could you also put printk() dumping content of 'stat' in
ide-iops.c::ide_wait_not_busy() so we can verify that it is not
some problem with ide_wait_not_busy() itself.
Sorry. :( I don't have access to the hardware anymore (which is a
"home-made" embedded machine). But from what I could get from poking
around was that the BSY-bit on the slave (that never has or ever will
exists) was set, probably because those who built the thing wanted to
save money and/or space on that "billionth of a cent"-resistor that Alan
Cox talked about.
Best regards
Jonas Stare
Signed-off-by: Jonas Stare <[email protected]>
--
diff -u linux-2.6.23.1-orig/drivers/ide/ide-probe.c
linux-2.6.23.1/drivers/ide/ide-probe.c
--- linux-2.6.23.1-orig/drivers/ide/ide-probe.c 2007-10-12
18:43:44.000000000 +0200
+++ linux-2.6.23.1/drivers/ide/ide-probe.c 2007-11-09
10:43:16.000000000 +0100
@@ -643,6 +643,7 @@
static int wait_hwif_ready(ide_hwif_t *hwif)
{
int rc;
+ int unit;
printk(KERN_DEBUG "Probing IDE interface %s...\n", hwif->name);
@@ -659,20 +660,24 @@
return rc;
Hmm, so the first ide_wait_not_busy() (for the currently
selected device) is OK and doesn't stall?
It didn't stall for me... But even if it had, probe_hwif() will ignore
the entire controller if you set "idex=noprobe".
(From drivers/ide/ide-probe.c)
static void probe_hwif(ide_hwif_t *hwif, void (*fixup)(ide_hwif_t *hwif))
{
unsigned int unit;
unsigned long flags;
unsigned int irqd;
if (hwif->noprobe)
return;
/* Now make sure both master & slave are ready */
- SELECT_DRIVE(&hwif->drives[0]);
- hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
- mdelay(2);
- rc = ide_wait_not_busy(hwif, 35000);
- if (rc)
- return rc;
- SELECT_DRIVE(&hwif->drives[1]);
- hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
- mdelay(2);
- rc = ide_wait_not_busy(hwif, 35000);
+ for (unit = 0; unit < MAX_DRIVES; ++unit) {
+ /* Ignore disks that we will not probe for later. */
+ if (!hwif->drives[unit].noprobe ||
+ hwif->drives[unit].forced_geom) {
It is better to check for ->present
(->forced_geom implies that ->present is set).
Great comment. :) I'll change that right away...
+ SELECT_DRIVE(&hwif->drives[unit]);
+ hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
+ mdelay(2);
+ rc = ide_wait_not_busy(hwif, 35000);
+ /* Exit function with master selected (let's be
sane) */
+ SELECT_DRIVE(&hwif->drives[0]);
This changes the previous behavior adding an extra SELECT_DRIVE()
before trying the slave drive.
Mmmm, yes, I know. But I couldn't come up with a clean and nice way to
be sure that the first drive is selected. Maybe I could move it inside
the if-statement below?
+ if (rc)
+ return rc;
+ } else {
+ printk(KERN_DEBUG "Skip ide_wait_not_busy for
%s:%d\n",
+ hwif->name, unit);
+ }
+ }
- /* Exit function with master reselected (let's be sane) */
- SELECT_DRIVE(&hwif->drives[0]);
-
return rc;
}
Maybe that's the fix, maybe not - I'll defer to others on that (please).
Your email client is wordwrapping the text, and replaces tabs with spaces.
Most of them seem to do this nowadays. For thunderbird, please see
http://mbligh.org/linuxdocs/Email/Clients/Thunderbird
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
