New (updated) version of ethernet driver for cris v10.
- First steps to simplify and make the MII code more similar
between the etrax100 and etraxfs ports.
- Start the transmit queue before enabling tx interrupts
to avoid race with the first frame.
- Flip the comparition statement to stick to physical addresses
to avoid phys_to_virt mapping a potential null pointer.
This was not an error but the change simplifies debugging
of address-space mappings.
- Made myPrevRxDesc local to e100_rx since it was only used there.
Fixed out of memory handling in e100_rx. If dev_alloc_skb() fails
persistently the system is hosed anyway but at least it won't
loop in an interrupt handler.
- Correct some code formatting issues.
- Add defines SET_ETH_ENABLE_LEDS, SET_ETH_DISABLE_LEDS
and SET_ETH_AUTONEG used in new cris v10 ethernet driver.
Signed-off-by: Jesper Nilsson <[email protected]>
---
drivers/net/cris/eth_v10.c | 430 ++++++++++++++++++++++++++++----------------
include/asm-cris/ethernet.h | 3
2 files changed, 280 insertions(+), 153 deletions(-)
diff -urBb -X /h/jespern/.exclude_files clean_linux-2.6.23/drivers/net/cris/eth_v10.c linux-2.6.23/drivers/net/cris/eth_v10.c
--- clean_linux-2.6.23/drivers/net/cris/eth_v10.c 2007-10-09 22:31:38.000000000 +0200
+++ linux-2.6.23/drivers/net/cris/eth_v10.c 2007-10-23 10:44:11.000000000 +0200
@@ -250,6 +39,7 @@
#include <asm/bitops.h>
#include <asm/ethernet.h>
#include <asm/cache.h>
+#include <asm/arch/io_interface_mux.h>
//#define ETHDEBUG
#define D(x)
@@ -279,6 +69,9 @@
* by this lock as well.
*/
spinlock_t lock;
+
+ spinlock_t led_lock; /* Protect LED state */
+ spinlock_t transceiver_lock; /* Protect transceiver state. */
};
typedef struct etrax_eth_descr
@@ -295,8 +88,6 @@
void (*check_duplex)(struct net_device* dev);
};
-struct transceiver_ops* transceiver;
-
/* Duplex settings */
enum duplex
{
@@ -307,7 +98,7 @@
/* Dma descriptors etc. */
-#define MAX_MEDIA_DATA_SIZE 1518
+#define MAX_MEDIA_DATA_SIZE 1522
#define MIN_PACKET_LEN 46
#define ETHER_HEAD_LEN 14
@@ -332,8 +123,8 @@
/*Intel LXT972A specific*/
#define MDIO_INT_STATUS_REG_2 0x0011
-#define MDIO_INT_FULL_DUPLEX_IND ( 1 << 9 )
-#define MDIO_INT_SPEED ( 1 << 14 )
+#define MDIO_INT_FULL_DUPLEX_IND (1 << 9)
+#define MDIO_INT_SPEED (1 << 14)
/* Network flash constants */
#define NET_FLASH_TIME (HZ/50) /* 20 ms */
@@ -344,8 +135,8 @@
#define NO_NETWORK_ACTIVITY 0
#define NETWORK_ACTIVITY 1
-#define NBR_OF_RX_DESC 64
-#define NBR_OF_TX_DESC 256
+#define NBR_OF_RX_DESC 32
+#define NBR_OF_TX_DESC 16
/* Large packets are sent directly to upper layers while small packets are */
/* copied (to reduce memory waste). The following constant decides the breakpoint */
@@ -367,7 +158,6 @@
static etrax_eth_descr *myNextRxDesc; /* Points to the next descriptor to
to be processed */
static etrax_eth_descr *myLastRxDesc; /* The last processed descriptor */
-static etrax_eth_descr *myPrevRxDesc; /* The descriptor right before myNextRxDesc */
static etrax_eth_descr RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned(32)));
@@ -377,7 +167,6 @@
static etrax_eth_descr TxDescList[NBR_OF_TX_DESC] __attribute__ ((aligned(32)));
static unsigned int network_rec_config_shadow = 0;
-static unsigned int mdio_phy_addr; /* Transciever address */
static unsigned int network_tr_ctrl_shadow = 0;
@@ -411,7 +200,7 @@
static void e100_tx_timeout(struct net_device *dev);
static struct net_device_stats *e100_get_stats(struct net_device *dev);
static void set_multicast_list(struct net_device *dev);
-static void e100_hardware_send_packet(char *buf, int length);
+static void e100_hardware_send_packet(struct net_local* np, char *buf, int length);
static void update_rx_stats(struct net_device_stats *);
static void update_tx_stats(struct net_device_stats *);
static int e100_probe_transceiver(struct net_device* dev);
@@ -434,7 +223,10 @@
static void e100_set_network_leds(int active);
static const struct ethtool_ops e100_ethtool_ops;
-
+#if defined(CONFIG_ETRAX_NO_PHY)
+static void dummy_check_speed(struct net_device* dev);
+static void dummy_check_duplex(struct net_device* dev);
+#else
static void broadcom_check_speed(struct net_device* dev);
static void broadcom_check_duplex(struct net_device* dev);
static void tdk_check_speed(struct net_device* dev);
@@ -443,16 +235,28 @@
static void intel_check_duplex(struct net_device* dev);
static void generic_check_speed(struct net_device* dev);
static void generic_check_duplex(struct net_device* dev);
+#endif
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void e100_netpoll(struct net_device* dev);
+#endif
+
+static int autoneg_normal = 1;
struct transceiver_ops transceivers[] =
{
+#if defined(CONFIG_ETRAX_NO_PHY)
+ {0x0000, dummy_check_speed, dummy_check_duplex} /* Dummy */
+#else
{0x1018, broadcom_check_speed, broadcom_check_duplex}, /* Broadcom */
{0xC039, tdk_check_speed, tdk_check_duplex}, /* TDK 2120 */
{0x039C, tdk_check_speed, tdk_check_duplex}, /* TDK 2120C */
{0x04de, intel_check_speed, intel_check_duplex}, /* Intel LXT972A*/
{0x0000, generic_check_speed, generic_check_duplex} /* Generic, must be last */
+#endif
};
+struct transceiver_ops* transceiver = &transceivers[0];
+
#define tx_done(dev) (*R_DMA_CH0_CMD == 0)
/*
@@ -471,14 +275,22 @@
int i, err;
printk(KERN_INFO
- "ETRAX 100LX 10/100MBit ethernet v2.0 (c) 2000-2003 Axis Communications AB\n");
+ "ETRAX 100LX 10/100MBit ethernet v2.0 (c) 1998-2007 Axis Communications AB\n");
- dev = alloc_etherdev(sizeof(struct net_local));
- np = dev->priv;
+ if (cris_request_io_interface(if_eth, cardname)) {
+ printk(KERN_CRIT "etrax_ethernet_init failed to get IO interface\n");
+ return -EBUSY;
+ }
+ dev = alloc_etherdev(sizeof(struct net_local));
if (!dev)
return -ENOMEM;
+ np = netdev_priv(dev);
+
+ /* we do our own locking */
+ dev->features |= NETIF_F_LLTX;
+
dev->base_addr = (unsigned int)R_NETWORK_SA_0; /* just to have something to show */
/* now setup our etrax specific stuff */
@@ -498,14 +310,22 @@
dev->do_ioctl = e100_ioctl;
dev->set_config = e100_set_config;
dev->tx_timeout = e100_tx_timeout;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ dev->poll_controller = e100_netpoll;
+#endif
+
+ spin_lock_init(&np->lock);
+ spin_lock_init(&np->led_lock);
+ spin_lock_init(&np->transceiver_lock);
/* Initialise the list of Etrax DMA-descriptors */
/* Initialise receive descriptors */
for (i = 0; i < NBR_OF_RX_DESC; i++) {
- /* Allocate two extra cachelines to make sure that buffer used by DMA
- * does not share cacheline with any other data (to avoid cache bug)
+ /* Allocate two extra cachelines to make sure that buffer used
+ * by DMA does not share cacheline with any other data (to
+ * avoid cache bug)
*/
RxDescList[i].skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE + 2 * L1_CACHE_BYTES);
if (!RxDescList[i].skb)
@@ -541,7 +362,6 @@
myNextRxDesc = &RxDescList[0];
myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1];
- myPrevRxDesc = &RxDescList[NBR_OF_RX_DESC - 1];
myFirstTxDesc = &TxDescList[0];
myNextTxDesc = &TxDescList[0];
myLastTxDesc = &TxDescList[NBR_OF_TX_DESC - 1];
@@ -562,10 +382,11 @@
current_speed = 10;
current_speed_selection = 0; /* Auto */
speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL;
- duplex_timer.data = (unsigned long)dev;
+ speed_timer.data = (unsigned long)dev;
speed_timer.function = e100_check_speed;
clear_led_timer.function = e100_clear_network_leds;
+ clear_led_timer.data = (unsigned long)dev;
full_duplex = 0;
current_duplex = autoneg;
@@ -574,7 +395,6 @@
duplex_timer.function = e100_check_duplex;
/* Initialize mii interface */
- np->mii_if.phy_id = mdio_phy_addr;
np->mii_if.phy_id_mask = 0x1f;
np->mii_if.reg_num_mask = 0x1f;
np->mii_if.dev = dev;
@@ -585,6 +405,9 @@
/* unwanted addresses are matched */
*R_NETWORK_GA_0 = 0x00000000;
*R_NETWORK_GA_1 = 0x00000000;
+
+ /* Initialize next time the led can flash */
+ led_next_time = jiffies;
return 0;
}
@@ -595,7 +418,7 @@
static int
e100_set_mac_address(struct net_device *dev, void *p)
{
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
struct sockaddr *addr = p;
int i;
@@ -690,6 +513,25 @@
goto grace_exit2;
}
+ /*
+ * Always allocate the DMA channels after the IRQ,
+ * and clean up on failure.
+ */
+
+ if (cris_request_dma(NETWORK_TX_DMA_NBR,
+ cardname,
+ DMA_VERBOSE_ON_ERROR,
+ dma_eth)) {
+ goto grace_exit3;
+ }
+
+ if (cris_request_dma(NETWORK_RX_DMA_NBR,
+ cardname,
+ DMA_VERBOSE_ON_ERROR,
+ dma_eth)) {
+ goto grace_exit4;
+ }
+
/* give the HW an idea of what MAC address we want */
*R_NETWORK_SA_0 = dev->dev_addr[0] | (dev->dev_addr[1] << 8) |
@@ -704,6 +546,7 @@
*R_NETWORK_REC_CONFIG = 0xd; /* broadcast rec, individ. rec, ma0 enabled */
#else
+ SETS(network_rec_config_shadow, R_NETWORK_REC_CONFIG, max_size, size1522);
SETS(network_rec_config_shadow, R_NETWORK_REC_CONFIG, broadcast, receive);
SETS(network_rec_config_shadow, R_NETWORK_REC_CONFIG, ma0, enable);
SETF(network_rec_config_shadow, R_NETWORK_REC_CONFIG, duplex, full_duplex);
@@ -723,8 +566,7 @@
SETS(network_tr_ctrl_shadow, R_NETWORK_TR_CTRL, crc, enable);
*R_NETWORK_TR_CTRL = network_tr_ctrl_shadow;
- save_flags(flags);
- cli();
+ local_irq_save(flags);
/* enable the irq's for ethernet DMA */
@@ -756,12 +598,13 @@
*R_DMA_CH0_FIRST = 0;
*R_DMA_CH0_DESCR = virt_to_phys(myLastTxDesc);
+ netif_start_queue(dev);
- restore_flags(flags);
+ local_irq_restore(flags);
/* Probe for transceiver */
if (e100_probe_transceiver(dev))
- goto grace_exit3;
+ goto grace_exit5;
/* Start duplex/speed timers */
add_timer(&speed_timer);
@@ -770,10 +613,14 @@
/* We are now ready to accept transmit requeusts from
* the queueing layer of the networking.
*/
- netif_start_queue(dev);
+ netif_carrier_on(dev);
return 0;
+grace_exit5:
+ cris_free_dma(NETWORK_RX_DMA_NBR, cardname);
+grace_exit4:
+ cris_free_dma(NETWORK_TX_DMA_NBR, cardname);
grace_exit3:
free_irq(NETWORK_STATUS_IRQ_NBR, (void *)dev);
grace_exit2:
@@ -784,12 +631,20 @@
return -EAGAIN;
}
-
+#if defined(CONFIG_ETRAX_NO_PHY)
+static void
+dummy_check_speed(struct net_device* dev)
+{
+ current_speed = 100;
+}
+#else
static void
generic_check_speed(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_ADVERTISE);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE);
if ((data & ADVERTISE_100FULL) ||
(data & ADVERTISE_100HALF))
current_speed = 100;
@@ -801,7 +656,10 @@
tdk_check_speed(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_TDK_DIAGNOSTIC_REG);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MDIO_TDK_DIAGNOSTIC_REG);
current_speed = (data & MDIO_TDK_DIAGNOSTIC_RATE ? 100 : 10);
}
@@ -809,7 +667,10 @@
broadcom_check_speed(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_AUX_CTRL_STATUS_REG);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MDIO_AUX_CTRL_STATUS_REG);
current_speed = (data & MDIO_BC_SPEED ? 100 : 10);
}
@@ -817,46 +678,62 @@
intel_check_speed(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_INT_STATUS_REG_2);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MDIO_INT_STATUS_REG_2);
current_speed = (data & MDIO_INT_SPEED ? 100 : 10);
}
-
+#endif
static void
e100_check_speed(unsigned long priv)
{
struct net_device* dev = (struct net_device*)priv;
+ struct net_local *np = netdev_priv(dev);
static int led_initiated = 0;
unsigned long data;
int old_speed = current_speed;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMSR);
+ spin_lock(&np->transceiver_lock);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMSR);
if (!(data & BMSR_LSTATUS)) {
current_speed = 0;
} else {
transceiver->check_speed(dev);
}
+ spin_lock(&np->led_lock);
if ((old_speed != current_speed) || !led_initiated) {
led_initiated = 1;
e100_set_network_leds(NO_NETWORK_ACTIVITY);
+ if (current_speed)
+ netif_carrier_on(dev);
+ else
+ netif_carrier_off(dev);
}
+ spin_unlock(&np->led_lock);
/* Reinitialize the timer. */
speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL;
add_timer(&speed_timer);
+
+ spin_unlock(&np->transceiver_lock);
}
static void
e100_negotiate(struct net_device* dev)
{
- unsigned short data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_ADVERTISE);
+ struct net_local *np = netdev_priv(dev);
+ unsigned short data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MII_ADVERTISE);
/* Discard old speed and duplex settings */
data &= ~(ADVERTISE_100HALF | ADVERTISE_100FULL |
ADVERTISE_10HALF | ADVERTISE_10FULL);
switch (current_speed_selection) {
- case 10 :
+ case 10:
if (current_duplex == full)
data |= ADVERTISE_10FULL;
else if (current_duplex == half)
@@ -865,7 +742,7 @@
data |= ADVERTISE_10HALF | ADVERTISE_10FULL;
break;
- case 100 :
+ case 100:
if (current_duplex == full)
data |= ADVERTISE_100FULL;
else if (current_duplex == half)
@@ -874,7 +751,7 @@
data |= ADVERTISE_100HALF | ADVERTISE_100FULL;
break;
- case 0 : /* Auto */
+ case 0: /* Auto */
if (current_duplex == full)
data |= ADVERTISE_100FULL | ADVERTISE_10FULL;
else if (current_duplex == half)
@@ -884,35 +761,44 @@
ADVERTISE_100HALF | ADVERTISE_100FULL;
break;
- default : /* assume autoneg speed and duplex */
+ default: /* assume autoneg speed and duplex */
data |= ADVERTISE_10HALF | ADVERTISE_10FULL |
ADVERTISE_100HALF | ADVERTISE_100FULL;
+ break;
}
- e100_set_mdio_reg(dev, mdio_phy_addr, MII_ADVERTISE, data);
+ e100_set_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE, data);
/* Renegotiate with link partner */
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMCR);
+ if (autoneg_normal) {
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
data |= BMCR_ANENABLE | BMCR_ANRESTART;
-
- e100_set_mdio_reg(dev, mdio_phy_addr, MII_BMCR, data);
+ }
+ e100_set_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR, data);
}
static void
e100_set_speed(struct net_device* dev, unsigned long speed)
{
+ struct net_local *np = netdev_priv(dev);
+
+ spin_lock(&np->transceiver_lock);
if (speed != current_speed_selection) {
current_speed_selection = speed;
e100_negotiate(dev);
}
+ spin_unlock(&np->transceiver_lock);
}
static void
e100_check_duplex(unsigned long priv)
{
struct net_device *dev = (struct net_device *)priv;
- struct net_local *np = (struct net_local *)dev->priv;
- int old_duplex = full_duplex;
+ struct net_local *np = netdev_priv(dev);
+ int old_duplex;
+
+ spin_lock(&np->transceiver_lock);
+ old_duplex = full_duplex;
transceiver->check_duplex(dev);
if (old_duplex != full_duplex) {
/* Duplex changed */
@@ -924,13 +810,22 @@
duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL;
add_timer(&duplex_timer);
np->mii_if.full_duplex = full_duplex;
+ spin_unlock(&np->transceiver_lock);
}
-
+#if defined(CONFIG_ETRAX_NO_PHY)
+static void
+dummy_check_duplex(struct net_device* dev)
+{
+ full_duplex = 1;
+}
+#else
static void
generic_check_duplex(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_ADVERTISE);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE);
if ((data & ADVERTISE_10FULL) ||
(data & ADVERTISE_100FULL))
full_duplex = 1;
@@ -942,7 +837,10 @@
tdk_check_duplex(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_TDK_DIAGNOSTIC_REG);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MDIO_TDK_DIAGNOSTIC_REG);
full_duplex = (data & MDIO_TDK_DIAGNOSTIC_DPLX) ? 1 : 0;
}
@@ -950,7 +848,10 @@
broadcom_check_duplex(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_AUX_CTRL_STATUS_REG);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MDIO_AUX_CTRL_STATUS_REG);
full_duplex = (data & MDIO_BC_FULL_DUPLEX_IND) ? 1 : 0;
}
@@ -958,38 +859,51 @@
intel_check_duplex(struct net_device* dev)
{
unsigned long data;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_INT_STATUS_REG_2);
+ struct net_local *np = netdev_priv(dev);
+
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id,
+ MDIO_INT_STATUS_REG_2);
full_duplex = (data & MDIO_INT_FULL_DUPLEX_IND) ? 1 : 0;
}
-
+#endif
static void
e100_set_duplex(struct net_device* dev, enum duplex new_duplex)
{
+ struct net_local *np = netdev_priv(dev);
+
+ spin_lock(&np->transceiver_lock);
if (new_duplex != current_duplex) {
current_duplex = new_duplex;
e100_negotiate(dev);
}
+ spin_unlock(&np->transceiver_lock);
}
static int
e100_probe_transceiver(struct net_device* dev)
{
+#if !defined(CONFIG_ETRAX_NO_PHY)
unsigned int phyid_high;
unsigned int phyid_low;
unsigned int oui;
struct transceiver_ops* ops = NULL;
+ struct net_local *np = netdev_priv(dev);
+
+ spin_lock(&np->transceiver_lock);
/* Probe MDIO physical address */
- for (mdio_phy_addr = 0; mdio_phy_addr <= 31; mdio_phy_addr++) {
- if (e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMSR) != 0xffff)
+ for (np->mii_if.phy_id = 0; np->mii_if.phy_id <= 31;
+ np->mii_if.phy_id++) {
+ if (e100_get_mdio_reg(dev,
+ np->mii_if.phy_id, MII_BMSR) != 0xffff)
break;
}
- if (mdio_phy_addr == 32)
+ if (np->mii_if.phy_id == 32)
return -ENODEV;
/* Get manufacturer */
- phyid_high = e100_get_mdio_reg(dev, mdio_phy_addr, MII_PHYSID1);
- phyid_low = e100_get_mdio_reg(dev, mdio_phy_addr, MII_PHYSID2);
+ phyid_high = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_PHYSID1);
+ phyid_low = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_PHYSID2);
oui = (phyid_high << 6) | (phyid_low >> 10);
for (ops = &transceivers[0]; ops->oui; ops++) {
@@ -998,6 +912,8 @@
}
transceiver = ops;
+ spin_unlock(&np->transceiver_lock);
+#endif
return 0;
}
@@ -1092,13 +1009,14 @@
static void
e100_reset_transceiver(struct net_device* dev)
{
+ struct net_local *np = netdev_priv(dev);
unsigned short cmd;
unsigned short data;
int bitCounter;
- data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMCR);
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
- cmd = (MDIO_START << 14) | (MDIO_WRITE << 12) | (mdio_phy_addr << 7) | (MII_BMCR << 2);
+ cmd = (MDIO_START << 14) | (MDIO_WRITE << 12) | (np->mii_if.phy_id << 7) | (MII_BMCR << 2);
e100_send_mdio_cmd(cmd, 1);
@@ -1116,7 +1034,7 @@
static void
e100_tx_timeout(struct net_device *dev)
{
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
unsigned long flags;
spin_lock_irqsave(&np->lock, flags);
@@ -1138,8 +1056,7 @@
e100_reset_transceiver(dev);
/* and get rid of the packets that never got an interrupt */
- while (myFirstTxDesc != myNextTxDesc)
- {
+ while (myFirstTxDesc != myNextTxDesc) {
dev_kfree_skb(myFirstTxDesc->skb);
myFirstTxDesc->skb = 0;
myFirstTxDesc = phys_to_virt(myFirstTxDesc->descr.next);
@@ -1165,7 +1082,7 @@
static int
e100_send_packet(struct sk_buff *skb, struct net_device *dev)
{
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
unsigned char *buf = skb->data;
unsigned long flags;
@@ -1178,7 +1095,7 @@
dev->trans_start = jiffies;
- e100_hardware_send_packet(buf, skb->len);
+ e100_hardware_send_packet(np, buf, skb->len);
myNextTxDesc = phys_to_virt(myNextTxDesc->descr.next);
@@ -1201,13 +1118,15 @@
e100rxtx_interrupt(int irq, void *dev_id)
{
struct net_device *dev = (struct net_device *)dev_id;
- struct net_local *np = (struct net_local *)dev->priv;
- unsigned long irqbits = *R_IRQ_MASK2_RD;
+ struct net_local *np = netdev_priv(dev);
+ unsigned long irqbits;
- /* Disable RX/TX IRQs to avoid reentrancy */
- *R_IRQ_MASK2_CLR =
- IO_STATE(R_IRQ_MASK2_CLR, dma0_eop, clr) |
- IO_STATE(R_IRQ_MASK2_CLR, dma1_eop, clr);
+ /*
+ * Note that both rx and tx interrupts are blocked at this point,
+ * regardless of which got us here.
+ */
+
+ irqbits = *R_IRQ_MASK2_RD;
/* Handle received packets */
if (irqbits & IO_STATE(R_IRQ_MASK2_RD, dma1_eop, active)) {
@@ -1223,7 +1142,7 @@
* allocate a new buffer to put a packet in.
*/
e100_rx(dev);
- ((struct net_local *)dev->priv)->stats.rx_packets++;
+ np->stats.rx_packets++;
/* restart/continue on the channel, for safety */
*R_DMA_CH1_CMD = IO_STATE(R_DMA_CH1_CMD, cmd, restart);
/* clear dma channel 1 eop/descr irq bits */
@@ -1237,9 +1156,8 @@
}
/* Report any packets that have been sent */
- while (myFirstTxDesc != phys_to_virt(*R_DMA_CH0_FIRST) &&
- myFirstTxDesc != myNextTxDesc)
- {
+ while (virt_to_phys(myFirstTxDesc) != *R_DMA_CH0_FIRST &&
+ (netif_queue_stopped(dev) || myFirstTxDesc != myNextTxDesc)) {
np->stats.tx_bytes += myFirstTxDesc->skb->len;
np->stats.tx_packets++;
@@ -1248,19 +1166,15 @@
dev_kfree_skb_irq(myFirstTxDesc->skb);
myFirstTxDesc->skb = 0;
myFirstTxDesc = phys_to_virt(myFirstTxDesc->descr.next);
+ /* Wake up queue. */
+ netif_wake_queue(dev);
}
if (irqbits & IO_STATE(R_IRQ_MASK2_RD, dma0_eop, active)) {
- /* acknowledge the eop interrupt and wake up queue */
+ /* acknowledge the eop interrupt. */
*R_DMA_CH0_CLR_INTR = IO_STATE(R_DMA_CH0_CLR_INTR, clr_eop, do);
- netif_wake_queue(dev);
}
- /* Enable RX/TX IRQs again */
- *R_IRQ_MASK2_SET =
- IO_STATE(R_IRQ_MASK2_SET, dma0_eop, set) |
- IO_STATE(R_IRQ_MASK2_SET, dma1_eop, set);
-
return IRQ_HANDLED;
}
@@ -1268,7 +1182,7 @@
e100nw_interrupt(int irq, void *dev_id)
{
struct net_device *dev = (struct net_device *)dev_id;
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
unsigned long irqbits = *R_IRQ_MASK0_RD;
/* check for underrun irq */
@@ -1290,7 +1204,6 @@
SETS(network_tr_ctrl_shadow, R_NETWORK_TR_CTRL, clr_error, clr);
*R_NETWORK_TR_CTRL = network_tr_ctrl_shadow;
SETS(network_tr_ctrl_shadow, R_NETWORK_TR_CTRL, clr_error, nop);
- *R_NETWORK_TR_CTRL = IO_STATE(R_NETWORK_TR_CTRL, clr_error, clr);
np->stats.tx_errors++;
D(printk("ethernet excessive collisions!\n"));
}
@@ -1303,12 +1216,13 @@
{
struct sk_buff *skb;
int length = 0;
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
unsigned char *skb_data_ptr;
#ifdef ETHDEBUG
int i;
#endif
-
+ etrax_eth_descr *prevRxDesc; /* The descriptor right before myNextRxDesc */
+ spin_lock(&np->led_lock);
if (!led_active && time_after(jiffies, led_next_time)) {
/* light the network leds depending on the current speed. */
e100_set_network_leds(NETWORK_ACTIVITY);
@@ -1318,9 +1232,10 @@
led_active = 1;
mod_timer(&clear_led_timer, jiffies + HZ/10);
}
+ spin_unlock(&np->led_lock);
length = myNextRxDesc->descr.hw_len - 4;
- ((struct net_local *)dev->priv)->stats.rx_bytes += length;
+ np->stats.rx_bytes += length;
#ifdef ETHDEBUG
printk("Got a packet of length %d:\n", length);
@@ -1340,7 +1255,7 @@
if (!skb) {
np->stats.rx_errors++;
printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name);
- return;
+ goto update_nextrxdesc;
}
skb_put(skb, length - ETHER_HEAD_LEN); /* allocate room for the packet body */
@@ -1358,15 +1273,15 @@
else {
/* Large packet, send directly to upper layers and allocate new
* memory (aligned to cache line boundary to avoid bug).
- * Before sending the skb to upper layers we must make sure that
- * skb->data points to the aligned start of the packet.
+ * Before sending the skb to upper layers we must make sure
+ * that skb->data points to the aligned start of the packet.
*/
int align;
struct sk_buff *new_skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE + 2 * L1_CACHE_BYTES);
if (!new_skb) {
np->stats.rx_errors++;
printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name);
- return;
+ goto update_nextrxdesc;
}
skb = myNextRxDesc->skb;
align = (int)phys_to_virt(myNextRxDesc->descr.buf) - (int)skb->data;
@@ -1381,9 +1296,10 @@
/* Send the packet to the upper layers */
netif_rx(skb);
+ update_nextrxdesc:
/* Prepare for next packet */
myNextRxDesc->descr.status = 0;
- myPrevRxDesc = myNextRxDesc;
+ prevRxDesc = myNextRxDesc;
myNextRxDesc = phys_to_virt(myNextRxDesc->descr.next);
rx_queue_len++;
@@ -1391,9 +1307,9 @@
/* Check if descriptors should be returned */
if (rx_queue_len == RX_QUEUE_THRESHOLD) {
flush_etrax_cache();
- myPrevRxDesc->descr.ctrl |= d_eol;
+ prevRxDesc->descr.ctrl |= d_eol;
myLastRxDesc->descr.ctrl &= ~d_eol;
- myLastRxDesc = myPrevRxDesc;
+ myLastRxDesc = prevRxDesc;
rx_queue_len = 0;
}
}
@@ -1402,7 +1318,7 @@
static int
e100_close(struct net_device *dev)
{
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
printk(KERN_INFO "Closing %s.\n", dev->name);
@@ -1430,6 +1346,9 @@
free_irq(NETWORK_DMA_TX_IRQ_NBR, (void *)dev);
free_irq(NETWORK_STATUS_IRQ_NBR, (void *)dev);
+ cris_free_dma(NETWORK_TX_DMA_NBR, cardname);
+ cris_free_dma(NETWORK_RX_DMA_NBR, cardname);
+
/* Update the statistics here. */
update_rx_stats(&np->stats);
@@ -1447,18 +1366,11 @@
{
struct mii_ioctl_data *data = if_mii(ifr);
struct net_local *np = netdev_priv(dev);
+ int rc = 0;
+ int old_autoneg;
spin_lock(&np->lock); /* Preempt protection */
switch (cmd) {
- case SIOCGMIIPHY: /* Get PHY address */
- data->phy_id = mdio_phy_addr;
- break;
- case SIOCGMIIREG: /* Read MII register */
- data->val_out = e100_get_mdio_reg(dev, mdio_phy_addr, data->reg_num);
- break;
- case SIOCSMIIREG: /* Write MII register */
- e100_set_mdio_reg(dev, mdio_phy_addr, data->reg_num, data->val_in);
- break;
/* The ioctls below should be considered obsolete but are */
/* still present for compatability with old scripts/apps */
case SET_ETH_SPEED_10: /* 10 Mbps */
@@ -1467,60 +1379,47 @@
case SET_ETH_SPEED_100: /* 100 Mbps */
e100_set_speed(dev, 100);
break;
- case SET_ETH_SPEED_AUTO: /* Auto negotiate speed */
+ case SET_ETH_SPEED_AUTO: /* Auto-negotiate speed */
e100_set_speed(dev, 0);
break;
- case SET_ETH_DUPLEX_HALF: /* Half duplex. */
+ case SET_ETH_DUPLEX_HALF: /* Half duplex */
e100_set_duplex(dev, half);
break;
- case SET_ETH_DUPLEX_FULL: /* Full duplex. */
+ case SET_ETH_DUPLEX_FULL: /* Full duplex */
e100_set_duplex(dev, full);
break;
- case SET_ETH_DUPLEX_AUTO: /* Autonegotiate duplex*/
+ case SET_ETH_DUPLEX_AUTO: /* Auto-negotiate duplex */
e100_set_duplex(dev, autoneg);
break;
+ case SET_ETH_AUTONEG:
+ old_autoneg = autoneg_normal;
+ autoneg_normal = *(int*)data;
+ if (autoneg_normal != old_autoneg)
+ e100_negotiate(dev);
+ break;
default:
- return -EINVAL;
+ rc = generic_mii_ioctl(&np->mii_if, if_mii(ifr),
+ cmd, NULL);
+ break;
}
spin_unlock(&np->lock);
- return 0;
+ return rc;
}
-static int e100_set_settings(struct net_device *dev,
- struct ethtool_cmd *ecmd)
+static int e100_get_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
{
- ecmd->supported = SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII |
- SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full;
- ecmd->port = PORT_TP;
- ecmd->transceiver = XCVR_EXTERNAL;
- ecmd->phy_address = mdio_phy_addr;
- ecmd->speed = current_speed;
- ecmd->duplex = full_duplex ? DUPLEX_FULL : DUPLEX_HALF;
- ecmd->advertising = ADVERTISED_TP;
-
- if (current_duplex == autoneg && current_speed_selection == 0)
- ecmd->advertising |= ADVERTISED_Autoneg;
- else {
- ecmd->advertising |=
- ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full |
- ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full;
- if (current_speed_selection == 10)
- ecmd->advertising &= ~(ADVERTISED_100baseT_Half |
- ADVERTISED_100baseT_Full);
- else if (current_speed_selection == 100)
- ecmd->advertising &= ~(ADVERTISED_10baseT_Half |
- ADVERTISED_10baseT_Full);
- if (current_duplex == half)
- ecmd->advertising &= ~(ADVERTISED_10baseT_Full |
- ADVERTISED_100baseT_Full);
- else if (current_duplex == full)
- ecmd->advertising &= ~(ADVERTISED_10baseT_Half |
- ADVERTISED_100baseT_Half);
- }
+ struct net_local *np = netdev_priv(dev);
+ int err;
- ecmd->autoneg = AUTONEG_ENABLE;
- return 0;
+ spin_lock_irq(&np->lock);
+ err = mii_ethtool_gset(&np->mii_if, cmd);
+ spin_unlock_irq(&np->lock);
+
+ /* The PHY may support 1000baseT, but the Etrax100 does not. */
+ cmd->supported &= ~(SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full);
+ return err;
}
static int e100_set_settings(struct net_device *dev,
@@ -1564,7 +1463,8 @@
static int
e100_set_config(struct net_device *dev, struct ifmap *map)
{
- struct net_local *np = (struct net_local *)dev->priv;
+ struct net_local *np = netdev_priv(dev);
+
spin_lock(&np->lock); /* Preempt protection */
switch(map->port) {
@@ -1616,7 +1522,6 @@
es->collisions +=
IO_EXTRACT(R_TR_COUNTERS, single_col, r) +
IO_EXTRACT(R_TR_COUNTERS, multiple_col, r);
- es->tx_errors += IO_EXTRACT(R_TR_COUNTERS, deferred, r);
}
/*
@@ -1626,8 +1531,9 @@
static struct net_device_stats *
e100_get_stats(struct net_device *dev)
{
- struct net_local *lp = (struct net_local *)dev->priv;
+ struct net_local *lp = netdev_priv(dev);
unsigned long flags;
+
spin_lock_irqsave(&lp->lock, flags);
update_rx_stats(&lp->stats);
@@ -1647,7 +1553,7 @@
static void
set_multicast_list(struct net_device *dev)
{
- struct net_local *lp = (struct net_local *)dev->priv;
+ struct net_local *lp = netdev_priv(dev);
int num_addr = dev->mc_count;
unsigned long int lo_bits;
unsigned long int hi_bits;
@@ -1651,9 +1557,9 @@
int num_addr = dev->mc_count;
unsigned long int lo_bits;
unsigned long int hi_bits;
+
spin_lock(&lp->lock);
- if (dev->flags & IFF_PROMISC)
- {
+ if (dev->flags & IFF_PROMISC) {
/* promiscuous mode */
lo_bits = 0xfffffffful;
hi_bits = 0xfffffffful;
@@ -1683,9 +1589,10 @@
struct dev_mc_list *dmi = dev->mc_list;
int i;
char *baddr;
+
lo_bits = 0x00000000ul;
hi_bits = 0x00000000ul;
- for (i=0; i<num_addr; i++) {
+ for (i = 0; i < num_addr; i++) {
/* Calculate the hash index for the GA registers */
hash_ix = 0;
@@ -1712,8 +1619,7 @@
if (hash_ix >= 32) {
hi_bits |= (1 << (hash_ix-32));
- }
- else {
+ } else {
lo_bits |= (1 << hash_ix);
}
dmi = dmi->next;
@@ -1728,10 +1634,11 @@
}
void
-e100_hardware_send_packet(char *buf, int length)
+e100_hardware_send_packet(struct net_local *np, char *buf, int length)
{
D(printk("e100 send pack, buf 0x%x len %d\n", buf, length));
+ spin_lock(&np->led_lock);
if (!led_active && time_after(jiffies, led_next_time)) {
/* light the network leds depending on the current speed. */
e100_set_network_leds(NETWORK_ACTIVITY);
@@ -1741,6 +1648,7 @@
led_active = 1;
mod_timer(&clear_led_timer, jiffies + HZ/10);
}
+ spin_unlock(&np->led_lock);
/* configure the tx dma descriptor */
myNextTxDesc->descr.sw_len = length;
@@ -1758,6 +1666,11 @@
static void
e100_clear_network_leds(unsigned long dummy)
{
+ struct net_device *dev = (struct net_device *)dummy;
+ struct net_local *np = netdev_priv(dev);
+
+ spin_lock(&np->led_lock);
+
if (led_active && time_after(jiffies, led_next_time)) {
e100_set_network_leds(NO_NETWORK_ACTIVITY);
@@ -1765,6 +1678,8 @@
led_next_time = jiffies + NET_FLASH_PAUSE;
led_active = 0;
}
+
+ spin_unlock(&np->led_lock);
}
static void
@@ -1785,19 +1700,25 @@
#else
LED_NETWORK_SET(LED_OFF);
#endif
- }
- else if (light_leds) {
+ } else if (light_leds) {
if (current_speed == 10) {
LED_NETWORK_SET(LED_ORANGE);
} else {
LED_NETWORK_SET(LED_GREEN);
}
- }
- else {
+ } else {
LED_NETWORK_SET(LED_OFF);
}
}
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void
+e100_netpoll(struct net_device* netdev)
+{
+ e100rxtx_interrupt(NETWORK_DMA_TX_IRQ_NBR, netdev, NULL);
+}
+#endif
+
static int
etrax_init_module(void)
{
diff -urBb -X /h/jespern/.exclude_files clean_linux-2.6.23/include/asm-cris/ethernet.h linux-2.6.23/include/asm-cris/ethernet.h
--- clean_linux-2.6.23/include/asm-cris/ethernet.h 2007-10-09 22:31:38.000000000 +0200
+++ linux-2.6.23/include/asm-cris/ethernet.h 2007-10-23 10:47:08.000000000 +0200
@@ -15,4 +15,7 @@
#define SET_ETH_DUPLEX_AUTO SIOCDEVPRIVATE+3 /* Auto neg duplex */
#define SET_ETH_DUPLEX_HALF SIOCDEVPRIVATE+4 /* Full duplex */
#define SET_ETH_DUPLEX_FULL SIOCDEVPRIVATE+5 /* Half duplex */
+#define SET_ETH_ENABLE_LEDS SIOCDEVPRIVATE+6 /* Enable net LEDs */
+#define SET_ETH_DISABLE_LEDS SIOCDEVPRIVATE+7 /* Disable net LEDs */
+#define SET_ETH_AUTONEG SIOCDEVPRIVATE+8
#endif /* _CRIS_ETHERNET_H */
/^JN - Jesper Nilsson
--
Jesper Nilsson -- [email protected]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
