- support BF54x SPI0
- clean up some code
- will support multiports in the future
Signed-off-by: Bryan Wu <[email protected]>
---
drivers/spi/spi_bfin5xx.c | 130 +++++++++++------------
include/asm-blackfin/mach-bf548/defBF54x_base.h | 17 +++
2 files changed, 80 insertions(+), 67 deletions(-)
diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index f540ed7..2992ada 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1,17 +1,20 @@
/*
- * File: drivers/spi/bfin5xx_spi.c
- * Based on: N/A
- * Author: Luke Yang (Analog Devices Inc.)
+ * File: drivers/spi/bfin5xx_spi.c
+ * Maintainer:
+ * Bryan Wu <[email protected]>
+ * Original Author:
+ * Luke Yang (Analog Devices Inc.)
*
- * Created: March. 10th 2006
- * Description: SPI controller driver for Blackfin 5xx
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * Created: March. 10th 2006
+ * Description: SPI controller driver for Blackfin BF5xx
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
*
* Modified:
* March 10, 2006 bfin5xx_spi.c Created. (Luke Yang)
* August 7, 2006 added full duplex mode (Axel Weiss & Luke Yang)
+ * July 17, 2007 add support for BF54x SPI0 controller (Bryan Wu)
*
- * Copyright 2004-2006 Analog Devices Inc.
+ * Copyright 2004-2007 Analog Devices Inc.
*
* This program is free software ; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -31,28 +34,27 @@
#include <linux/init.h>
#include <linux/module.h>
+#include <linux/delay.h>
#include <linux/device.h>
+#include <linux/io.h>
#include <linux/ioport.h>
+#include <linux/irq.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
#include <linux/workqueue.h>
-#include <linux/errno.h>
-#include <linux/delay.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/delay.h>
#include <asm/dma.h>
-
+#include <asm/portmux.h>
#include <asm/bfin5xx_spi.h>
-MODULE_AUTHOR("Luke Yang");
-MODULE_DESCRIPTION("Blackfin 5xx SPI Contoller");
+MODULE_AUTHOR("Bryan Wu, Luke Yang");
+MODULE_DESCRIPTION("Blackfin BF5xx SPI Contoller Driver");
MODULE_LICENSE("GPL");
+#define DRV_NAME "bfin-spi-master"
#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0)
#define DEFINE_SPI_REG(reg, off) \
@@ -125,6 +127,7 @@ struct chip_data {
u16 flag;
u8 chip_select_num;
+ u8 chip_select_requested;
u8 n_bytes;
u8 width; /* 0 or 1 */
u8 enable_dma;
@@ -189,53 +192,37 @@ static void restore_state(struct driver_data *drv_data)
bfin_spi_disable(drv_data);
dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n");
-#if defined(CONFIG_BF534) || defined(CONFIG_BF536) || defined(CONFIG_BF537)
- dev_dbg(&drv_data->pdev->dev,
- "chip select number is %d\n", chip->chip_select_num);
-
- switch (chip->chip_select_num) {
- case 1:
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3c00);
- SSYNC();
- break;
-
- case 2:
- case 3:
- bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PJSE_SPI);
- SSYNC();
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3800);
- SSYNC();
- break;
-
- case 4:
- bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PFS4E_SPI);
- SSYNC();
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3840);
- SSYNC();
- break;
+ if (!chip->chip_select_requested) {
- case 5:
- bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PFS5E_SPI);
- SSYNC();
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3820);
- SSYNC();
- break;
+ dev_dbg(&drv_data->pdev->dev,
+ "chip select number is %d\n", chip->chip_select_num);
- case 6:
- bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PFS6E_SPI);
- SSYNC();
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3810);
- SSYNC();
- break;
+ switch (chip->chip_select_num) {
+ case 1:
+ peripheral_request(P_SPI0_SSEL1, DRV_NAME);
+ break;
+ case 2:
+ peripheral_request(P_SPI0_SSEL2, DRV_NAME);
+ break;
+ case 3:
+ peripheral_request(P_SPI0_SSEL3, DRV_NAME);
+ break;
+ case 4:
+ peripheral_request(P_SPI0_SSEL4, DRV_NAME);
+ break;
+ case 5:
+ peripheral_request(P_SPI0_SSEL5, DRV_NAME);
+ break;
+ case 6:
+ peripheral_request(P_SPI0_SSEL6, DRV_NAME);
+ break;
+ case 7:
+ peripheral_request(P_SPI0_SSEL7, DRV_NAME);
+ break;
+ }
- case 7:
- bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PJCE_SPI);
- SSYNC();
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3800);
- SSYNC();
- break;
+ chip->chip_select_requested = 1;
}
-#endif
/* Load the registers */
write_CTRL(chip->ctl_reg);
@@ -278,7 +265,7 @@ static void null_reader(struct driver_data *drv_data)
static void u8_writer(struct driver_data *drv_data)
{
- dev_dbg(&drv_data->pdev->dev,
+ dev_dbg(&drv_data->pdev->dev,
"cr8-s is 0x%x\n", read_STAT());
while (drv_data->tx < drv_data->tx_end) {
write_TDBR(*(u8 *) (drv_data->tx));
@@ -317,7 +304,7 @@ static void u8_cs_chg_writer(struct driver_data *drv_data)
static void u8_reader(struct driver_data *drv_data)
{
- dev_dbg(&drv_data->pdev->dev,
+ dev_dbg(&drv_data->pdev->dev,
"cr-8 is 0x%x\n", read_STAT());
/* clear TDBR buffer before read(else it will be shifted out) */
@@ -404,7 +391,7 @@ static void u8_cs_chg_duplex(struct driver_data *drv_data)
static void u16_writer(struct driver_data *drv_data)
{
- dev_dbg(&drv_data->pdev->dev,
+ dev_dbg(&drv_data->pdev->dev,
"cr16 is 0x%x\n", read_STAT());
while (drv_data->tx < drv_data->tx_end) {
@@ -817,7 +804,7 @@ static void pump_transfers(unsigned long data)
/* full duplex mode */
BUG_ON((drv_data->tx_end - drv_data->tx) !=
(drv_data->rx_end - drv_data->rx));
- cr = (read_CTRL() & (~BIT_CTL_TIMOD));
+ cr = (read_CTRL() & (~BIT_CTL_TIMOD));
cr |= CFG_SPI_WRITE | (width << 8) |
(CFG_SPI_ENABLE << 14);
dev_dbg(&drv_data->pdev->dev,
@@ -835,7 +822,7 @@ static void pump_transfers(unsigned long data)
cr = (read_CTRL() & (~BIT_CTL_TIMOD));
cr |= CFG_SPI_WRITE | (width << 8) |
(CFG_SPI_ENABLE << 14);
- dev_dbg(&drv_data->pdev->dev,
+ dev_dbg(&drv_data->pdev->dev,
"IO write: cr is 0x%x\n", cr);
write_CTRL(cr);
@@ -850,7 +837,7 @@ static void pump_transfers(unsigned long data)
cr = (read_CTRL() & (~BIT_CTL_TIMOD));
cr |= CFG_SPI_READ | (width << 8) |
(CFG_SPI_ENABLE << 14);
- dev_dbg(&drv_data->pdev->dev,
+ dev_dbg(&drv_data->pdev->dev,
"IO read: cr is 0x%x\n", cr);
write_CTRL(cr);
@@ -862,7 +849,7 @@ static void pump_transfers(unsigned long data)
}
if (!tranf_success) {
- dev_dbg(&drv_data->pdev->dev,
+ dev_dbg(&drv_data->pdev->dev,
"IO write error!\n");
message->state = ERROR_STATE;
} else {
@@ -917,8 +904,8 @@ static void pump_messages(struct work_struct *work)
"got a message to pump, state is set to: baud %d, flag 0x%x, ctl 0x%x\n",
drv_data->cur_chip->baud, drv_data->cur_chip->flag,
drv_data->cur_chip->ctl_reg);
-
- dev_dbg(&drv_data->pdev->dev,
+
+ dev_dbg(&drv_data->pdev->dev,
"the first transfer len is %d\n",
drv_data->cur_transfer->len);
@@ -1194,6 +1181,15 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev)
dev_err(&pdev->dev, "can not alloc spi_master\n");
return -ENOMEM;
}
+
+ if (peripheral_request(P_SPI0_SCK, DRV_NAME) ||
+ peripheral_request(P_SPI0_MISO, DRV_NAME) ||
+ peripheral_request(P_SPI0_MOSI, DRV_NAME) ) {
+
+ dev_err(&pdev->dev, ": Requesting Peripherals failed\n");
+ goto out_error_queue_alloc;
+ }
+
drv_data = spi_master_get_devdata(master);
drv_data->master = master;
drv_data->master_info = platform_info;
diff --git a/include/asm-blackfin/mach-bf548/defBF54x_base.h b/include/asm-blackfin/mach-bf548/defBF54x_base.h
index 895ddd4..56f0a76 100644
--- a/include/asm-blackfin/mach-bf548/defBF54x_base.h
+++ b/include/asm-blackfin/mach-bf548/defBF54x_base.h
@@ -1637,8 +1637,25 @@
#define RESTART 0x20 /* Work Unit Transitions */
#define DI_SEL 0x40 /* Data Interrupt Timing Select */
#define DI_EN 0x80 /* Data Interrupt Enable */
+
#define NDSIZE 0xf00 /* Flex Descriptor Size */
+#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */
+#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */
+#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */
+#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */
+#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */
+#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */
+#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */
+#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */
+#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */
+#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */
+
#define DMAFLOW 0xf000 /* Next Operation */
+#define DMAFLOW_STOP 0x0000 /* Stop Mode */
+#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */
+#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */
+#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */
+#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */
/* Bit masks for DMAx_IRQ_STATUS, MDMA_Sx_IRQ_STATUS, MDMA_Dx_IRQ_STATUS */
--
1.5.3.4
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
