[PATCH 5/9] Blackfin SPI driver: update spi driver to support multi-ports

[Bryan Wu <bryan.wu@analog.com>]

update spi driver to support multi-ports by add platform_resource,
tested on STAMP537+SPI_MMC, other boards need more testing

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
---
 drivers/spi/spi_bfin5xx.c |  124 ++++++++++++++++++++++++++++++---------------
 1 files changed, 83 insertions(+), 41 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 1a83656..891d263 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -13,6 +13,8 @@
  *	March 10, 2006  bfin5xx_spi.c Created. (Luke Yang)
  *      August 7, 2006  added full duplex mode (Axel Weiss & Luke Yang)
  *      July  17, 2007  add support for BF54x SPI0 controller (Bryan Wu)
+ *      July  30, 2007  add platfrom_resource interface to support multi-port
+ *                      SPI controller (Bryan Wu)
  *
  * Copyright 2004-2007 Analog Devices Inc.
  *
@@ -50,18 +52,25 @@
 #include <asm/portmux.h>
 #include <asm/bfin5xx_spi.h>
 
-MODULE_AUTHOR("Bryan Wu, Luke Yang");
-MODULE_DESCRIPTION("Blackfin BF5xx SPI Contoller Driver");
+#define DRV_NAME	"bfin-spi"
+#define DRV_AUTHOR	"Bryan Wu, Luke Yang"
+#define DRV_DESC	"Blackfin BF5xx on-chip SPI Contoller Driver"
+#define DRV_VERSION	"1.0"
+
+MODULE_AUTHOR(DRV_AUTHOR);
+MODULE_DESCRIPTION(DRV_DESC);
 MODULE_LICENSE("GPL");
 
-#define DRV_NAME	"bfin-spi-master"
 #define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0)
 
+static u32 spi_dma_ch;
+static u32 spi_regs_base;
+
 #define DEFINE_SPI_REG(reg, off) \
 static inline u16 read_##reg(void) \
-	{ return bfin_read16(SPI0_REGBASE + off); } \
+	{ return bfin_read16(spi_regs_base + off); } \
 static inline void write_##reg(u16 v) \
-	{bfin_write16(SPI0_REGBASE + off, v); }
+	{bfin_write16(spi_regs_base + off, v); }
 
 DEFINE_SPI_REG(CTRL, 0x00)
 DEFINE_SPI_REG(FLAG, 0x04)
@@ -573,10 +582,10 @@ static irqreturn_t dma_irq_handler(int irq, void *dev_id)
 	struct chip_data *chip = drv_data->cur_chip;
 
 	dev_dbg(&drv_data->pdev->dev, "in dma_irq_handler\n");
-	clear_dma_irqstat(CH_SPI);
+	clear_dma_irqstat(spi_dma_ch);
 
 	/* Wait for DMA to complete */
-	while (get_dma_curr_irqstat(CH_SPI) & DMA_RUN)
+	while (get_dma_curr_irqstat(spi_dma_ch) & DMA_RUN)
 		continue;
 
 	/*
@@ -586,12 +595,12 @@ static irqreturn_t dma_irq_handler(int irq, void *dev_id)
 	 * register until it goes low for 2 successive reads
 	 */
 	if (drv_data->tx != NULL) {
-		while ((bfin_read_SPI_STAT() & TXS) ||
-		       (bfin_read_SPI_STAT() & TXS))
+		while ((read_STAT() & TXS) ||
+		       (read_STAT() & TXS))
 			continue;
 	}
 
-	while (!(bfin_read_SPI_STAT() & SPIF))
+	while (!(read_STAT() & SPIF))
 		continue;
 
 	bfin_spi_disable(drv_data);
@@ -610,8 +619,8 @@ static irqreturn_t dma_irq_handler(int irq, void *dev_id)
 	/* free the irq handler before next transfer */
 	dev_dbg(&drv_data->pdev->dev,
 		"disable dma channel irq%d\n",
-		CH_SPI);
-	dma_disable_irq(CH_SPI);
+		spi_dma_ch);
+	dma_disable_irq(spi_dma_ch);
 
 	return IRQ_HANDLED;
 }
@@ -726,19 +735,19 @@ static void pump_transfers(unsigned long data)
 	if (drv_data->cur_chip->enable_dma && drv_data->len > 6) {
 
 		write_STAT(BIT_STAT_CLR);
-		disable_dma(CH_SPI);
-		clear_dma_irqstat(CH_SPI);
+		disable_dma(spi_dma_ch);
+		clear_dma_irqstat(spi_dma_ch);
 		bfin_spi_disable(drv_data);
 
 		/* config dma channel */
 		dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n");
 		if (width == CFG_SPI_WORDSIZE16) {
-			set_dma_x_count(CH_SPI, drv_data->len);
-			set_dma_x_modify(CH_SPI, 2);
+			set_dma_x_count(spi_dma_ch, drv_data->len);
+			set_dma_x_modify(spi_dma_ch, 2);
 			dma_width = WDSIZE_16;
 		} else {
-			set_dma_x_count(CH_SPI, drv_data->len);
-			set_dma_x_modify(CH_SPI, 1);
+			set_dma_x_count(spi_dma_ch, drv_data->len);
+			set_dma_x_modify(spi_dma_ch, 1);
 			dma_width = WDSIZE_8;
 		}
 
@@ -753,9 +762,10 @@ static void pump_transfers(unsigned long data)
 			/* no irq in autobuffer mode */
 			dma_config =
 			    (DMAFLOW_AUTO | RESTART | dma_width | DI_EN);
-			set_dma_config(CH_SPI, dma_config);
-			set_dma_start_addr(CH_SPI, (unsigned long)drv_data->tx);
-			enable_dma(CH_SPI);
+			set_dma_config(spi_dma_ch, dma_config);
+			set_dma_start_addr(spi_dma_ch,
+					(unsigned long)drv_data->tx);
+			enable_dma(spi_dma_ch);
 			write_CTRL(cr | CFG_SPI_DMAWRITE | (width << 8) |
 				   (CFG_SPI_ENABLE << 14));
 
@@ -776,14 +786,15 @@ static void pump_transfers(unsigned long data)
 			/* clear tx reg soformer data is not shifted out */
 			write_TDBR(0xFF);
 
-			set_dma_x_count(CH_SPI, drv_data->len);
+			set_dma_x_count(spi_dma_ch, drv_data->len);
 
 			/* start dma */
-			dma_enable_irq(CH_SPI);
+			dma_enable_irq(spi_dma_ch);
 			dma_config = (WNR | RESTART | dma_width | DI_EN);
-			set_dma_config(CH_SPI, dma_config);
-			set_dma_start_addr(CH_SPI, (unsigned long)drv_data->rx);
-			enable_dma(CH_SPI);
+			set_dma_config(spi_dma_ch, dma_config);
+			set_dma_start_addr(spi_dma_ch,
+					(unsigned long)drv_data->rx);
+			enable_dma(spi_dma_ch);
 
 			cr |=
 			    CFG_SPI_DMAREAD | (width << 8) | (CFG_SPI_ENABLE <<
@@ -794,11 +805,12 @@ static void pump_transfers(unsigned long data)
 			dev_dbg(&drv_data->pdev->dev, "doing DMA out.\n");
 
 			/* start dma */
-			dma_enable_irq(CH_SPI);
+			dma_enable_irq(spi_dma_ch);
 			dma_config = (RESTART | dma_width | DI_EN);
-			set_dma_config(CH_SPI, dma_config);
-			set_dma_start_addr(CH_SPI, (unsigned long)drv_data->tx);
-			enable_dma(CH_SPI);
+			set_dma_config(spi_dma_ch, dma_config);
+			set_dma_start_addr(spi_dma_ch,
+					(unsigned long)drv_data->tx);
+			enable_dma(spi_dma_ch);
 
 			write_CTRL(cr | CFG_SPI_DMAWRITE | (width << 8) |
 				   (CFG_SPI_ENABLE << 14));
@@ -1030,17 +1042,17 @@ static int setup(struct spi_device *spi)
 	 */
 	if (chip->enable_dma && !dma_requested) {
 		/* register dma irq handler */
-		if (request_dma(CH_SPI, "BF53x_SPI_DMA") < 0) {
+		if (request_dma(spi_dma_ch, "BF53x_SPI_DMA") < 0) {
 			dev_dbg(&spi->dev,
 				"Unable to request BlackFin SPI DMA channel\n");
 			return -ENODEV;
 		}
-		if (set_dma_callback(CH_SPI, (void *)dma_irq_handler, drv_data)
-		    < 0) {
+		if (set_dma_callback(spi_dma_ch, (void *)dma_irq_handler,
+			drv_data) < 0) {
 			dev_dbg(&spi->dev, "Unable to set dma callback\n");
 			return -EPERM;
 		}
-		dma_disable_irq(CH_SPI);
+		dma_disable_irq(spi_dma_ch);
 		dma_requested = 1;
 	}
 
@@ -1212,6 +1224,7 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev)
 	struct bfin5xx_spi_master *platform_info;
 	struct spi_master *master;
 	struct driver_data *drv_data = 0;
+	struct resource *res;
 	int status = 0;
 
 	platform_info = dev->platform_data;
@@ -1239,15 +1252,38 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev)
 	master->setup = setup;
 	master->transfer = transfer;
 
+	/* Find and map our resources */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res == NULL) {
+		dev_err(dev, "Cannot get IORESOURCE_MEM\n");
+		status = -ENOENT;
+		goto out_error_get_res;
+	}
+
+	spi_regs_base = (u32) ioremap(res->start, (res->end - res->start)+1);
+	if (!spi_regs_base) {
+		dev_err(dev, "Cannot map IO\n");
+		status = -ENXIO;
+		goto out_error_ioremap;
+	}
+
+	spi_dma_ch = platform_get_irq(pdev, 0);
+	if (spi_dma_ch < 0) {
+		dev_err(dev, "No DMA channel specified\n");
+		status = -ENOENT;
+		goto out_error_no_dma_ch;
+	}
+
 	/* Initial and start queue */
 	status = init_queue(drv_data);
 	if (status != 0) {
-		dev_err(&pdev->dev, "problem initializing queue\n");
+		dev_err(dev, "problem initializing queue\n");
 		goto out_error_queue_alloc;
 	}
+
 	status = start_queue(drv_data);
 	if (status != 0) {
-		dev_err(&pdev->dev, "problem starting queue\n");
+		dev_err(dev, "problem starting queue\n");
 		goto out_error_queue_alloc;
 	}
 
@@ -1255,14 +1291,20 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, drv_data);
 	status = spi_register_master(master);
 	if (status != 0) {
-		dev_err(&pdev->dev, "problem registering spi master\n");
+		dev_err(dev, "problem registering spi master\n");
 		goto out_error_queue_alloc;
 	}
-	dev_dbg(&pdev->dev, "controller probe successfully\n");
+
+	dev_info(dev, "%s, Version %s, regs_base @ 0x%08x\n",
+		DRV_DESC, DRV_VERSION, spi_regs_base);
 	return status;
 
 out_error_queue_alloc:
 	destroy_queue(drv_data);
+out_error_no_dma_ch:
+	iounmap((void *) spi_regs_base);
+out_error_ioremap:
+out_error_get_res:
 out_error:
 	spi_master_put(master);
 
@@ -1288,8 +1330,8 @@ static int __devexit bfin5xx_spi_remove(struct platform_device *pdev)
 
 	/* Release DMA */
 	if (drv_data->master_info->enable_dma) {
-		if (dma_channel_active(CH_SPI))
-			free_dma(CH_SPI);
+		if (dma_channel_active(spi_dma_ch))
+			free_dma(spi_dma_ch);
 	}
 
 	/* Disconnect from the SPI framework */
@@ -1344,7 +1386,7 @@ static int bfin5xx_spi_resume(struct platform_device *pdev)
 MODULE_ALIAS("bfin-spi-master");	/* for platform bus hotplug */
 static struct platform_driver bfin5xx_spi_driver = {
 	.driver	= {
-		.name	= "bfin-spi-master",
+		.name	= DRV_NAME,
 		.owner	= THIS_MODULE,
 	},
 	.suspend	= bfin5xx_spi_suspend,
-- 
1.5.3.4
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/