Re: [PATCH] sb1250-mac: Driver model & phylib update

[Jeff Garzik <jgarzik@pobox.com>]

Maciej W. Rozycki wrote:
>  A driver model and phylib update.  It includes the following changes:
>
> 1. Removal of unused module options.
>
> 2. Phylib support and the resulting removal of generic bits for handling
>    the PHY.
>
> 3. Proper reserving of device resources and using ioremap()ped handles
>    to access MAC registers rather than platform-specific macros.
>
> 4. Handling of the device using the driver model.
>
> Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
> ---
>  This is a resubmission and this patch has waited for some time now as the 
> original submission triggered some concerns on the way phylib handled 
> interrupt-driven PHY units.  The issues were resolved a while ago already, 
> but I was distracted by some other work, mainly in the toolchain area, so 
> this got postponed this far.  For some background information -- as a 
> reminder -- here is the original long explanation I gave back then:
>  "Here is a set of patches that update the sb1250-mac driver used for the 
> onchip Gigabit Ethernet interfaces of the Broadcom SiByte family of SOCs 
> including the BCM1250 and a couple of other members.  These are used, 
> among others, on various Broadcom evaluation boards together with Broadcom 
> Gigabit Ethernet PHY chips.  Changes include porting the driver to the 
> driver model as a platform device, support for phylib, including the 
> BCM54xx PHYs in the interrupt mode, proper resource managment and a couple 
> of minor clean-ups.
>  Apart from changes to networking code, there are a few required in the
> architecture-specific areas and therefore I am sending these changes to
> Ralf and the linux-mips list as well.  It might also involve a few more
> interested parties in the discussion.
>
>  The changes were tested with a Broadcom SWARM board, which includes a
> BCM1250 part which has 3 MAC units on chip, of which 2 are usable, with
> BCM5421 PHY chips attached (both wired to the same interrupt line, which
> made testing whether IRQ sharing works properly in phylib possible).
> Link partners included a 1000base and a 100base interface doing
> autonegotiation as well as a 10base one doing none.
>
>  Other Broadcom boards that I know of may have these or BCM5411 or BCM5461
> chips.  The lack of documentation or at least actual pieces of hardware
> makes the use of interrupts impossible for all but the SWARM, the Sentosa
> and the Shorty (with the latter unsupported by Linux)."
>
>  All the bits except from the mentioned architecture-specific fix -- the 
> firmware of the SWARM gets the polarity of the PHY IRQ line wrong, which 
> has to be reprogrammed in the SOC -- have found their way into Linux 
> already.  The polarity fix is not critical for the update provided here as 
> the update has been written such that with the current state of affairs 
> the driver will use the polled mode of phylib operation.
>  I will provide the architecture-specific fix later on, probably once this 
> update has propagated back to the linux-mips.org tree (suggestions as to 
> why I should do otherwise certainly welcome).  This way if any problems 
> are seen due to the switch of the PHY to the interrupt-driven mode, they 
> can be sorted out independently of this change.
>  This change applies to the current netdev-2.6.git#upstream tree, on top 
> of "patch-netdev-2.6.23-rc6-20070920-sb1250-mac-typedef-9" submitted 
> yesterday.
>  Please apply.
>
>   Maciej
applied


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/