On 9/14/07, Andy Whitcroft <[email protected]> wrote:
> On Tue, Sep 11, 2007 at 04:31:12AM +0900, FUJITA Tomonori wrote:
> [...]
> >
> > Even if we revert the qla1280 patch, scsi-ml still sends chaining sg
> > list. So it doesn't work.
> >
> > The following patch disables chaining sg list for qla1280. If the fix
> > that I've just sent doesn't work, please try this.
>
> Ok, the other patch _did_ work, but this got tested anyhow and it did
> _not_ fix things.
>
Sorry to confirm this. My RAID5 got destroyed a second time.
To summarize what worked / not worked / and seems to work for me:
First 2 tries with unpatched rc4-mm1: Both times one sata_sil24-drive got kicked
Then I switched back to rc3-mm1, 18 boots with that kernel worked.
Then I tried the patched rc4-mm1 and it worked too.
The next boot also worked, but the third time kicked a drive out again.
But as nobody reads logs, I did not notice that and keep using the
patched rc4-mm1.
The next 5 times the system worked normally with the two remaining drives.
The sixth boot kicked the second sata_sil24 drive. That I did notice...
After reassembling the RAID, I'm now back to the patch rc4-mm1 that
did boot correctly this time.
So the patch just makes it unlikelier to hit the bug. Instead of
failing 2 out of 2 times, it only failed 2 out of 8 times.
I compared the rc4-mm1 boot from a working case and the case where it
kicked the first drive. Nothing seems to stand out...
< == good rc4-mm1 boot
> == bad rc4-mm1 boot that kicked the drive
145c145
< CPU 0: aperture @ 4000000 size 32 MB
---
> CPU 0: aperture @ b7f0000000 size 32 MB
154c154
< Calibrating delay using timer specific routine.. 5203.23 BogoMIPS
(lpj=26016160)
---
> Calibrating delay using timer specific routine.. 5203.22 BogoMIPS (lpj=26016138)
169c169
< APIC timer calibration result 12499998
---
> APIC timer calibration result 12499994
173c173
< Calibrating delay using timer specific routine.. 5222.40 BogoMIPS
(lpj=26112010)
---
> Calibrating delay using timer specific routine.. 5200.01 BogoMIPS (lpj=26000052)
182c182
< Calibrating delay using timer specific routine.. 5222.73 BogoMIPS
(lpj=26113694)
---
> Calibrating delay using timer specific routine.. 5200.01 BogoMIPS (lpj=26000081)
191c191
< Calibrating delay using timer specific routine.. 5223.07 BogoMIPS
(lpj=26115369)
---
> Calibrating delay using timer specific routine.. 5200.03 BogoMIPS (lpj=26000164)
269d268
< Switched to high resolution mode on CPU 3
270a270
> Switched to high resolution mode on CPU 3
502,509c502,509
< raid6: int64x1 2634 MB/s
< raid6: int64x2 3244 MB/s
< raid6: int64x4 3405 MB/s
< raid6: int64x8 2614 MB/s
< raid6: sse2x1 3607 MB/s
< raid6: sse2x2 4834 MB/s
< raid6: sse2x4 4946 MB/s
< raid6: using algorithm sse2x4 (4946 MB/s)
---
> raid6: int64x1 2680 MB/s
> raid6: int64x2 3232 MB/s
> raid6: int64x4 3411 MB/s
> raid6: int64x8 2620 MB/s
> raid6: sse2x1 3606 MB/s
> raid6: sse2x2 4810 MB/s
> raid6: sse2x4 4910 MB/s
> raid6: using algorithm sse2x4 (4910 MB/s)
567c567
< md1: bitmap initialized from disk: read 10/10 pages, set 96 bits
---
> md1: bitmap initialized from disk: read 10/10 pages, set 104 bits
568a569,655
> ata1.00: exception Emask 0x20 SAct 0x1 SErr 0x0 action 0x2
> ata1.00: irq_stat 0x00020002, PCI master abort while fetching SGT
> ata1.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0 cdb 0x0 data 4096 out
> res 50/00:00:af:ea:42/00:00:25:00:00/e0 Emask 0x20 (host bus error)
> ata1.00: status: {DRDY }
> ata1: soft resetting link
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: configured for UDMA/100
> ata1: EH complete
> sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ata1.00: exception Emask 0x20 SAct 0x1 SErr 0x0 action 0x2
> ata1.00: irq_stat 0x00020002, PCI master abort while fetching SGT
> ata1.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0 cdb 0x0 data 4096 out
> res 50/00:00:af:ea:42/00:00:25:00:00/e0 Emask 0x20 (host bus error)
> ata1.00: status: {DRDY }
> ata1: soft resetting link
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: configured for UDMA/100
> ata1: EH complete
> sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ata1.00: exception Emask 0x20 SAct 0x1 SErr 0x0 action 0x2
> ata1.00: irq_stat 0x00020002, PCI master abort while fetching SGT
> ata1.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0 cdb 0x0 data 4096 out
> res 50/00:00:af:ea:42/00:00:25:00:00/e0 Emask 0x20 (host bus error)
> ata1.00: status: {DRDY }
> ata1: soft resetting link
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: configured for UDMA/100
> ata1: EH complete
> sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ata1.00: exception Emask 0x20 SAct 0x1 SErr 0x0 action 0x2
> ata1.00: irq_stat 0x00020002, PCI master abort while fetching SGT
> ata1.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0 cdb 0x0 data 4096 out
> res 50/00:00:af:ea:42/00:00:25:00:00/e0 Emask 0x20 (host bus error)
> ata1.00: status: {DRDY }
> ata1: soft resetting link
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: configured for UDMA/100
> ata1: EH complete
> sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ata1.00: exception Emask 0x20 SAct 0x1 SErr 0x0 action 0x2
> ata1.00: irq_stat 0x00020002, PCI master abort while fetching SGT
> ata1.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0 cdb 0x0 data 4096 out
> res 50/00:00:af:ea:42/00:00:25:00:00/e0 Emask 0x20 (host bus error)
> ata1.00: status: {DRDY }
> ata1: soft resetting link
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: configured for UDMA/100
> ata1: EH complete
> sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ata1.00: exception Emask 0x20 SAct 0x1 SErr 0x0 action 0x2
> ata1.00: irq_stat 0x00020002, PCI master abort while fetching SGT
> ata1.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0 cdb 0x0 data 4096 out
> res 50/00:00:af:ea:42/00:00:25:00:00/e0 Emask 0x20 (host bus error)
> ata1.00: status: {DRDY }
> ata1: soft resetting link
> ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> ata1.00: configured for UDMA/100
> sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
> sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 00 00 00 af
> sd 0:0:0:0: [sda] Add. Sense: No additional sense information
> end_request: I/O error, dev sda, sector 625137161
> ata1: EH complete
> sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> md: super_written gets error=-5, uptodate=0
> raid5: Disk failure on sda2, disabling device. Operation continuing on 2 devices
571a659,663
> RAID5 conf printout:
> --- rd:3 wd:2
> disk 0, o:0, dev:sda2
> disk 1, o:1, dev:sdb2
> disk 2, o:1, dev:sdc2
576a669,672
> RAID5 conf printout:
> --- rd:3 wd:2
> disk 1, o:1, dev:sdb2
> disk 2, o:1, dev:sdc2
Another good boot also showed the aperture at a similar high address:
CPU 0: aperture @ b7f2000000 size 32 MB
And that good boot also showed the "correct" BogoMIPS:
Calibrating delay using timer specific routine.. 5205.43 BogoMIPS (lpj=26027183)
Calibrating delay using timer specific routine.. 5200.01 BogoMIPS (lpj=26000052)
Calibrating delay using timer specific routine.. 5200.01 BogoMIPS (lpj=26000082)
Calibrating delay using timer specific routine.. 5200.03 BogoMIPS (lpj=26000166)
Anything more I can provide to help debugging this?
Torsten
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
