According to DSDT, it is expected behavior.
_STA for BAT1 will return 0f (absent) until first _Q09 query from EC.
So, we should get BAT1 absent at init time, and some time later
it will appear (if queries are going through).
Regards,
Alex.
Norbert Preining wrote:
> Hi Len,
>
> On Die, 14 Aug 2007, Len Brown wrote:
>
>>> But there is still the strange thing that
>>> ACPI: Battery Slot [BAT1] (battery absent)
>>> is present in the dmesg, while
>>> $ acpi
>>> Battery 1: charging, 46%, 00:00:49 until charged
>>>
>> Does the system support more than 1 battery?
>>
>
> At least not physically ...
>
>
>> Can you show the full dmesg and the full contents of /proc/acpi/battery/*/*?
>>
>
> dmesg I sent already, but attached here from
> 2.6.23-rc3 + acpi-ec-fix-regression
>
> $ ls /proc/acpi/battery/
> BAT1
> $ ls /proc/acpi/battery/BAT1
> alarm info state
> $ cat /proc/acpi/battery/BAT1/alarm
> alarm: unsupported
> $ cat /proc/acpi/battery/BAT1/info
> present: yes
> design capacity: 2000 mAh
> last full capacity: 1649 mAh
> battery technology: rechargeable
> design voltage: 11100 mV
> design capacity warning: 300 mAh
> design capacity low: 65 mAh
> capacity granularity 1: 32 mAh
> capacity granularity 2: 32 mAh
> model number: ZH01
> serial number: 40110
> battery type: LION
> OEM info: SANYO
> $ cat /proc/acpi/battery/BAT1/state
> present: yes
> capacity state: ok
> charging state: charged
> present rate: 0 mA
> remaining capacity: 1649 mAh
> present voltage: 12538 mV
>
> Best wishes
>
> Norbert
>
> -------------------------------------------------------------------------------
> Dr. Norbert Preining <[email protected]> Vienna University of Technology
> Debian Developer <[email protected]> Debian TeX Group
> gpg DSA: 0x09C5B094 fp: 14DF 2E6C 0307 BE6D AD76 A9C0 D2BF 4AA3 09C5 B094
> -------------------------------------------------------------------------------
> DULEEK (n.)
> Sudden realisation, as you lie in bed waiting for the alarm to go off,
> that it should have gone off an hour ago.
> --- Douglas Adams, The Meaning of Liff
>
> ------------------------------------------------------------------------
>
> Linux version 2.6.23-rc3 (root@mithrandir) (gcc version 4.1.3 20070812 (prerelease) (Debian 4.1.2-15)) #7 SMP PREEMPT Tue Aug 14 08:59:17 CEST 2007
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000003f680000 (usable)
> BIOS-e820: 000000003f680000 - 000000003f696000 (ACPI data)
> BIOS-e820: 000000003f696000 - 000000003f700000 (ACPI NVS)
> BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
> BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
> BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
> 118MB HIGHMEM available.
> 896MB LOWMEM available.
> found SMP MP-table at 000f69f0
> Entering add_active_range(0, 0, 259712) 0 entries of 256 used
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 229376
> HighMem 229376 -> 259712
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 259712
> On node 0 totalpages: 259712
> DMA zone: 32 pages used for memmap
> DMA zone: 0 pages reserved
> DMA zone: 4064 pages, LIFO batch:0
> Normal zone: 1760 pages used for memmap
> Normal zone: 223520 pages, LIFO batch:31
> HighMem zone: 237 pages used for memmap
> HighMem zone: 30099 pages, LIFO batch:7
> Movable zone: 0 pages used for memmap
> DMI present.
> ACPI: RSDP 000F6920, 0014 (r0 PTLTD )
> ACPI: RSDT 3F68CF85, 0040 (r1 PTLTD RSDT 6040000 LTP 0)
> ACPI: FACP 3F695E20, 0074 (r1 INTEL CALISTGA 6040000 LOHR 5A)
> ACPI: DSDT 3F68D941, 84DF (r1 INTEL CALISTGA 6040000 MSFT 2000002)
> ACPI: FACS 3F696FC0, 0040
> ACPI: APIC 3F695E94, 0068 (r1 INTEL CALISTGA 6040000 LOHR 5A)
> ACPI: HPET 3F695EFC, 0038 (r1 INTEL CALISTGA 6040000 LOHR 5A)
> ACPI: MCFG 3F695F34, 003C (r1 INTEL CALISTGA 6040000 LOHR 5A)
> ACPI: APIC 3F695F70, 0068 (r1 PTLTD APIC 6040000 LTP 0)
> ACPI: BOOT 3F695FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
> ACPI: SSDT 3F68CFC5, 04F6 (r1 PmRef CpuPm 3000 INTL 20050624)
> ACPI: BIOS bug: multiple APIC/MADT found, using 0
> ACPI: If "acpi_apic_instance=2" works better, notify [email protected]
> ACPI: PM-Timer IO Port: 0x1008
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> Processor #0 6:14 APIC version 20
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> Processor #1 6:14 APIC version 20
> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode: Flat. Using 1 I/O APICs
> ACPI: HPET id: 0x8086a201 base: 0xfed00000
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
> swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
> swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000dc000
> swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
> Built 1 zonelists in Zone order. Total pages: 257683
> Kernel command line: root=/dev/sda6 ro resume=/dev/sda5
> mapped APIC to ffffb000 (fee00000)
> mapped IOAPIC to ffffa000 (fec00000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 16384 bytes)
> Detected 1666.906 MHz processor.
> Console: colour VGA+ 80x25
> console [tty0] enabled
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 1022248k/1038848k available (2325k kernel code, 15888k reserved, 1028k data, 200k init, 121344k highmem)
> virtual kernel memory layout:
> fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB)
> pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
> .init : 0xc044e000 - 0xc0480000 ( 200 kB)
> .data : 0xc0345426 - 0xc04464a4 (1028 kB)
> .text : 0xc0100000 - 0xc0345426 (2325 kB)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
> hpet0: 3 64-bit timers, 14318180 Hz
> Calibrating delay using timer specific routine.. 3337.27 BogoMIPS (lpj=6674558)
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 00000000
> monitor/mwait feature present.
> using mwait in idle threads.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 2048K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 0
> CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> Compat vDSO mapped to ffffe000.
> Checking 'hlt' instruction... OK.
> SMP alternatives: switching to UP code
> ACPI: Core revision 20070126
> ACPI: Table DSDT replaced by host OS
> ACPI: DSDT 00000000, 79B8 (r1 INTEL CALISTGA 6040000 INTL 20060912)
> ACPI: DSDT override uses original SSDTs unless "acpi_no_auto_ssdt"CPU0: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08
> SMP alternatives: switching to SMP code
> Booting processor 1/1 eip 3000
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3333.62 BogoMIPS (lpj=6667256)
> CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 00000000
> monitor/mwait feature present.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 2048K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#1.
> CPU1: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08
> Total of 2 processors activated (6670.90 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> checking TSC synchronization [CPU#0 -> CPU#1]: passed.
> Brought up 2 CPUs
> PM: Adding info for No Bus:platform
> NET: Registered protocol family 16
> PM: Adding info for No Bus:vtcon0
> ACPI: bus type pci registered
> PM: Adding info for No Bus:id
> PCI: Using MMCONFIG
> Setting up standard PCI resources
> ACPI: EC: Look up EC in DSDT
> ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
> ACPI: System BIOS is requesting _OSI(Linux)
> ACPI: If "acpi_osi=Linux" works better,
> Please send dmidecode to [email protected]
> ACPI: Interpreter enabled
> ACPI: (supports S0 S3)
> ACPI: Using IOAPIC for interrupt routing
> PM: Adding info for acpi:LNXSYSTM:00
> PM: Adding info for acpi:LNXPWRBN:00
> PM: Adding info for acpi:ACPI0007:00
> PM: Adding info for acpi:ACPI0007:01
> PM: Adding info for acpi:device:00
> PM: Adding info for acpi:PNP0A08:00
> PM: Adding info for acpi:PNP0C02:00
> PM: Adding info for acpi:LNXVIDEO:00
> PM: Adding info for acpi:device:01
> PM: Adding info for acpi:device:02
> PM: Adding info for acpi:device:03
> PM: Adding info for acpi:device:04
> PM: Adding info for acpi:device:05
> PM: Adding info for acpi:device:06
> PM: Adding info for acpi:device:07
> PM: Adding info for acpi:device:08
> PM: Adding info for acpi:device:09
> PM: Adding info for acpi:device:0a
> PM: Adding info for acpi:device:0b
> PM: Adding info for acpi:device:0c
> PM: Adding info for acpi:device:0d
> PM: Adding info for acpi:device:0e
> PM: Adding info for acpi:device:0f
> PM: Adding info for acpi:device:10
> PM: Adding info for acpi:device:11
> PM: Adding info for acpi:device:12
> PM: Adding info for acpi:device:13
> PM: Adding info for acpi:device:14
> PM: Adding info for acpi:device:15
> PM: Adding info for acpi:device:16
> PM: Adding info for acpi:device:17
> PM: Adding info for acpi:device:18
> PM: Adding info for acpi:device:19
> PM: Adding info for acpi:device:1a
> PM: Adding info for acpi:device:1b
> PM: Adding info for acpi:PNP0C0F:00
> PM: Adding info for acpi:PNP0C0F:01
> PM: Adding info for acpi:PNP0C0F:02
> PM: Adding info for acpi:PNP0C0F:03
> PM: Adding info for acpi:PNP0C0F:04
> PM: Adding info for acpi:PNP0C0F:05
> PM: Adding info for acpi:PNP0C0F:06
> PM: Adding info for acpi:PNP0C0F:07
> PM: Adding info for acpi:PNP0C09:00
> PM: Adding info for acpi:PNP0200:00
> PM: Adding info for acpi:PNP0103:00
> PM: Adding info for acpi:PNP0000:00
> PM: Adding info for acpi:PNP0C04:00
> PM: Adding info for acpi:PNP0C02:01
> PM: Adding info for acpi:PNP0B00:00
> PM: Adding info for acpi:PNP0100:00
> PM: Adding info for acpi:PNP0A05:00
> PM: Adding info for acpi:NSC6001:00
> PM: Adding info for acpi:PNP0501:00
> PM: Adding info for acpi:PNP0401:00
> PM: Adding info for acpi:PNP0303:00
> PM: Adding info for acpi:SYN1003:00
> PM: Adding info for acpi:device:1c
> PM: Adding info for acpi:device:1d
> PM: Adding info for acpi:device:1e
> PM: Adding info for acpi:device:1f
> PM: Adding info for acpi:device:20
> PM: Adding info for acpi:device:21
> PM: Adding info for acpi:device:22
> PM: Adding info for acpi:device:23
> PM: Adding info for acpi:ACPI0003:00
> PM: Adding info for acpi:PNP0C0A:00
> PM: Adding info for acpi:PNP0C0D:00
> PM: Adding info for acpi:PNP0C0C:00
> PM: Adding info for acpi:PNP0C0E:00
> PM: Adding info for acpi:PNP0C14:00
> PM: Adding info for acpi:LNXTHERM:00
> PM: Adding info for acpi:LNXTHERM:01
> ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PM: Adding info for No Bus:pci0000:00
> PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
> PCI quirk: region 1180-11bf claimed by ICH6 GPIO
> PCI: Transparent bridge - 0000:00:1e.0
> PCI: Bus #0b (-#0e) is hidden behind transparent bridge #0a (-#0b) (try 'pci=assign-busses')
> Please report the result to <[email protected]> to fix this permanently
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
> PM: Adding info for pci:0000:00:00.0
> PM: Adding info for pci:0000:00:02.0
> PM: Adding info for pci:0000:00:02.1
> PM: Adding info for pci:0000:00:1b.0
> PM: Adding info for pci:0000:00:1c.0
> PM: Adding info for pci:0000:00:1c.1
> PM: Adding info for pci:0000:00:1c.2
> PM: Adding info for pci:0000:00:1c.3
> PM: Adding info for pci:0000:00:1d.0
> PM: Adding info for pci:0000:00:1d.1
> PM: Adding info for pci:0000:00:1d.2
> PM: Adding info for pci:0000:00:1d.3
> PM: Adding info for pci:0000:00:1d.7
> PM: Adding info for pci:0000:00:1e.0
> PM: Adding info for pci:0000:00:1f.0
> PM: Adding info for pci:0000:00:1f.2
> PM: Adding info for pci:0000:00:1f.3
> PM: Adding info for pci:0000:02:00.0
> PM: Adding info for pci:0000:03:00.0
> PM: Adding info for pci:0000:0a:09.0
> PM: Adding info for pci:0000:0a:09.1
> PM: Adding info for pci:0000:0a:09.2
> ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
> ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
> ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
> ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
> ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> PM: Adding info for No Bus:pnp0
> ACPI: bus type pnp registered
> PM: Adding info for pnp:00:00
> PM: Adding info for pnp:00:01
> PM: Adding info for pnp:00:02
> PM: Adding info for pnp:00:03
> PM: Adding info for pnp:00:04
> PM: Adding info for pnp:00:05
> PM: Adding info for pnp:00:06
> PM: Adding info for pnp:00:07
> PM: Adding info for pnp:00:08
> PM: Adding info for pnp:00:09
> PM: Adding info for pnp:00:0a
> PM: Adding info for pnp:00:0b
> pnp: PnP ACPI: found 12 devices
> ACPI: ACPI bus type pnp unregistered
> SCSI subsystem initialized
> libata version 2.21 loaded.
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
> PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
> PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0
> PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
> PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
> PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
> PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.2
> PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.2
> PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.2
> PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.3
> PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.3
> PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.3
> Bluetooth: Core ver 2.11
> PM: Adding info for platform:bluetooth
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> ACPI: RTC can wake from S4
> Time: tsc clocksource has been installed.
> Switched to high resolution mode on CPU 0
> Switched to high resolution mode on CPU 1
> pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
> pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
> pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
> pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
> pnp: 00:03: iomem range 0xfed00000-0xfed003ff could not be reserved
> PM: Adding info for No Bus:mem
> PM: Adding info for No Bus:kmem
> PM: Adding info for No Bus:null
> PM: Adding info for No Bus:port
> PM: Adding info for No Bus:zero
> PM: Adding info for No Bus:full
> PM: Adding info for No Bus:random
> PM: Adding info for No Bus:urandom
> PM: Adding info for No Bus:kmsg
> PCI: Bridge: 0000:00:1c.0
> IO window: disabled.
> MEM window: 54000000-540fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1c.1
> IO window: disabled.
> MEM window: 54100000-541fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1c.2
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1c.3
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bus 11, cardbus bridge: 0000:0a:09.0
> IO window: 00002000-000020ff
> IO window: 00002400-000024ff
> PREFETCH window: 50000000-53ffffff
> MEM window: 58000000-5bffffff
> PCI: Bridge: 0000:00:1e.0
> IO window: 2000-2fff
> MEM window: b0400000-b04fffff
> PREFETCH window: 50000000-53ffffff
> PCI: Enabling device 0000:00:1c.0 (0000 -> 0002)
> ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> PCI: Enabling device 0000:00:1c.1 (0000 -> 0002)
> ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
> PCI: Setting latency timer of device 0000:00:1c.1 to 64
> ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1c.2 to 64
> ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1c.3 to 64
> PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> ACPI: PCI Interrupt 0000:0a:09.0[A] -> GSI 20 (level, low) -> IRQ 20
> NET: Registered protocol family 2
> IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
> TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> TCP: Hash tables configured (established 131072 bind 65536)
> TCP reno registered
> checking if image is initramfs... it is
> Freeing initrd memory: 2979k freed
> Simple Boot Flag at 0x3e set to 0x1
> Machine check exception polling timer started.
> PM: Adding info for No Bus:msr0
> PM: Adding info for No Bus:msr1
> PM: Adding info for No Bus:cpu0
> PM: Adding info for No Bus:cpu1
> PM: Adding info for No Bus:microcode
> PM: Adding info for platform:microcode
> IA-32 Microcode Update Driver: v1.14a <[email protected]>
> PM: Adding info for platform:pcspkr
> PM: Adding info for No Bus:snapshot
> highmem bounce pool size: 64 pages
> io scheduler noop registered
> io scheduler anticipatory registered (default)
> io scheduler deadline registered
> io scheduler cfq registered
> Boot video device is 0000:00:02.0
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.0:pcie00]
> PM: Adding info for pci_express:0000:00:1c.0:pcie00
> Allocate Port Service[0000:00:1c.0:pcie02]
> PM: Adding info for pci_express:0000:00:1c.0:pcie02
> Allocate Port Service[0000:00:1c.0:pcie03]
> PM: Adding info for pci_express:0000:00:1c.0:pcie03
> PCI: Setting latency timer of device 0000:00:1c.1 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.1:pcie00]
> PM: Adding info for pci_express:0000:00:1c.1:pcie00
> Allocate Port Service[0000:00:1c.1:pcie02]
> PM: Adding info for pci_express:0000:00:1c.1:pcie02
> Allocate Port Service[0000:00:1c.1:pcie03]
> PM: Adding info for pci_express:0000:00:1c.1:pcie03
> PCI: Setting latency timer of device 0000:00:1c.2 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.2:pcie00]
> PM: Adding info for pci_express:0000:00:1c.2:pcie00
> Allocate Port Service[0000:00:1c.2:pcie02]
> PM: Adding info for pci_express:0000:00:1c.2:pcie02
> Allocate Port Service[0000:00:1c.2:pcie03]
> PM: Adding info for pci_express:0000:00:1c.2:pcie03
> PCI: Setting latency timer of device 0000:00:1c.3 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.3:pcie00]
> PM: Adding info for pci_express:0000:00:1c.3:pcie00
> Allocate Port Service[0000:00:1c.3:pcie02]
> PM: Adding info for pci_express:0000:00:1c.3:pcie02
> Allocate Port Service[0000:00:1c.3:pcie03]
> PM: Adding info for pci_express:0000:00:1c.3:pcie03
> ACPI: AC Adapter [ACAD] (on-line)
> ACPI: Battery Slot [BAT1] (battery absent)
> PM: Adding info for No Bus:input0
> input: Power Button (FF) as /devices/virtual/input/input0
> ACPI: Power Button (FF) [PWRF]
> PM: Adding info for No Bus:input1
> input: Lid Switch as /devices/virtual/input/input1
> ACPI: Lid Switch [LID]
> PM: Adding info for No Bus:input2
> input: Power Button (CM) as /devices/virtual/input/input2
> ACPI: Power Button (CM) [PWRB]
> PM: Adding info for No Bus:input3
> input: Sleep Button (CM) as /devices/virtual/input/input3
> ACPI: Sleep Button (CM) [SLPB]
> ACPI: SSDT 3F68D710, 01A8 (r1 PmRef Cpu0Ist 3000 INTL 20050624)
> ACPI: SSDT 3F68D4BB, 01D0 (r1 PmRef Cpu0Cst 3001 INTL 20050624)
> ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
> ACPI: Processor [CPU0] (supports 8 throttling states)
> ACPI: SSDT 3F68D8B8, 0089 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
> ACPI: SSDT 3F68D68B, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
> ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
> ACPI: Processor [CPU1] (supports 8 throttling states)
> Marking TSC unstable due to: possible TSC halt in C2.
> Time: hpet clocksource has been installed.
> ACPI: Thermal Zone [THRM] (48 C)
> PM: Adding info for No Bus:tty
> PM: Adding info for No Bus:console
> PM: Adding info for No Bus:ptmx
> PM: Adding info for No Bus:tty0
> PM: Adding info for No Bus:vcs
> PM: Adding info for No Bus:vcsa
> PM: Adding info for No Bus:tty1
> PM: Adding info for No Bus:tty2
> PM: Adding info for No Bus:tty3
> PM: Adding info for No Bus:tty4
> PM: Adding info for No Bus:tty5
> PM: Adding info for No Bus:tty6
> PM: Adding info for No Bus:tty7
> PM: Adding info for No Bus:tty8
> PM: Adding info for No Bus:tty9
> PM: Adding info for No Bus:tty10
> PM: Adding info for No Bus:tty11
> PM: Adding info for No Bus:tty12
> PM: Adding info for No Bus:tty13
> PM: Adding info for No Bus:tty14
> PM: Adding info for No Bus:tty15
> PM: Adding info for No Bus:tty16
> PM: Adding info for No Bus:tty17
> PM: Adding info for No Bus:tty18
> PM: Adding info for No Bus:tty19
> PM: Adding info for No Bus:tty20
> PM: Adding info for No Bus:tty21
> PM: Adding info for No Bus:tty22
> PM: Adding info for No Bus:tty23
> PM: Adding info for No Bus:tty24
> PM: Adding info for No Bus:tty25
> PM: Adding info for No Bus:tty26
> PM: Adding info for No Bus:tty27
> PM: Adding info for No Bus:tty28
> PM: Adding info for No Bus:tty29
> PM: Adding info for No Bus:tty30
> PM: Adding info for No Bus:tty31
> PM: Adding info for No Bus:tty32
> PM: Adding info for No Bus:tty33
> PM: Adding info for No Bus:tty34
> PM: Adding info for No Bus:tty35
> PM: Adding info for No Bus:tty36
> PM: Adding info for No Bus:tty37
> PM: Adding info for No Bus:tty38
> PM: Adding info for No Bus:tty39
> PM: Adding info for No Bus:tty40
> PM: Adding info for No Bus:tty41
> PM: Adding info for No Bus:tty42
> PM: Adding info for No Bus:tty43
> PM: Adding info for No Bus:tty44
> PM: Adding info for No Bus:tty45
> PM: Adding info for No Bus:tty46
> PM: Adding info for No Bus:tty47
> PM: Adding info for No Bus:tty48
> PM: Adding info for No Bus:tty49
> PM: Adding info for No Bus:tty50
> PM: Adding info for No Bus:tty51
> PM: Adding info for No Bus:tty52
> PM: Adding info for No Bus:tty53
> PM: Adding info for No Bus:tty54
> PM: Adding info for No Bus:tty55
> PM: Adding info for No Bus:tty56
> PM: Adding info for No Bus:tty57
> PM: Adding info for No Bus:tty58
> PM: Adding info for No Bus:tty59
> PM: Adding info for No Bus:tty60
> PM: Adding info for No Bus:tty61
> PM: Adding info for No Bus:tty62
> PM: Adding info for No Bus:tty63
> PM: Adding info for No Bus:rtc
> Real Time Clock Driver v1.12ac
> PM: Adding info for No Bus:hpet
> hpet_resources: 0xfed00000 is busy
> intel_rng: FWH not detected
> Linux agpgart interface v0.102
> agpgart: Detected an Intel 945GM Chipset.
> agpgart: Detected 7932K stolen memory.
> PM: Adding info for No Bus:agpgart
> agpgart: AGP aperture is 256M @ 0xc0000000
> [drm] Initialized drm 1.1.0 20060810
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
> [drm] Initialized i915 1.6.0 20060119 on minor 0
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> tg3.c:v3.80 (August 2, 2007)
> PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
> ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
> PCI: Setting latency timer of device 0000:03:00.0 to 64
> PM: Adding info for No Bus:eth0
> eth0: Tigon3 [partno(BCM95789) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:16:36:1e:27:ad
> eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
> eth0: dma_rwctrl[76180000] dma_mask[64-bit]
> PM: Adding info for No Bus:lo
> ata_piix 0000:00:1f.2: version 2.11
> ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
> Clocksource tsc unstable (delta = -117952383 ns)
> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> scsi0 : ata_piix
> PM: Adding info for No Bus:host0
> scsi1 : ata_piix
> PM: Adding info for No Bus:host1
> ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000118b0 irq 14
> ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000118b8 irq 15
> ata1.00: ATA-7: ST9100824AS, 3.06, max UDMA/133
> ata1.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 0/32)
> ata1.00: configured for UDMA/133
> PM: Adding info for No Bus:target0:0:0
> scsi 0:0:0:0: Direct-Access ATA ST9100824AS 3.06 PQ: 0 ANSI: 5
> PM: Adding info for scsi:0:0:0:0
> sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
> sd 0:0:0:0: [sda] Attached SCSI disk
> Yenta: CardBus bridge found at 0000:0a:09.0 [1025:0098]
> Yenta: Using CSCINT to route CSC interrupts to PCI
> Yenta: Routing CardBus interrupts to PCI
> Yenta TI: socket 0000:0a:09.0, mfunc 0x01321b22, devctl 0x66
> Yenta: ISA IRQ mask 0x0cf8, PCI irq 20
> Socket status: 30000006
> Yenta: Raising subordinate bus# of parent bus (#0a) from #0b to #0e
> pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
> pcmcia: parent PCI bridge Memory window: 0xb0400000 - 0xb04fffff
> pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
> PM: Adding info for No Bus:pcmcia_socket0
> PM: Adding info for No Bus:usbmon0
> ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 21
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: EHCI Host Controller
> PM: Adding info for No Bus:usbmon1
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:1d.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: irq 21, io mem 0xb0004000
> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> PM: Adding info for usb:usb1
> PM: Adding info for No Bus:usbdev1.1_ep00
> usb usb1: configuration #1 chosen from 1 choice
> PM: Adding info for usb:1-0:1.0
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> PM: Adding info for No Bus:usbdev1.1_ep81
> PM: Adding info for No Bus:usbdev1.1
> USB Universal Host Controller Interface driver v3.0
> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 21
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: UHCI Host Controller
> PM: Adding info for No Bus:usbmon2
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:1d.0: irq 21, io base 0x00001820
> PM: Adding info for usb:usb2
> PM: Adding info for No Bus:usbdev2.1_ep00
> usb usb2: configuration #1 chosen from 1 choice
> PM: Adding info for usb:2-0:1.0
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PM: Adding info for No Bus:usbdev2.1_ep81
> PM: Adding info for No Bus:usbdev2.1
> ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: UHCI Host Controller
> PM: Adding info for No Bus:usbmon3
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
> PM: Adding info for usb:usb3
> PM: Adding info for No Bus:usbdev3.1_ep00
> usb usb3: configuration #1 chosen from 1 choice
> PM: Adding info for usb:3-0:1.0
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> PM: Adding info for No Bus:usbdev3.1_ep81
> PM: Adding info for No Bus:usbdev3.1
> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: UHCI Host Controller
> PM: Adding info for No Bus:usbmon4
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
> PM: Adding info for usb:usb4
> PM: Adding info for No Bus:usbdev4.1_ep00
> usb usb4: configuration #1 chosen from 1 choice
> PM: Adding info for usb:4-0:1.0
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> usb 1-8: new high speed USB device using ehci_hcd and address 2
> PM: Adding info for No Bus:usbdev4.1_ep81
> PM: Adding info for No Bus:usbdev4.1
> ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1d.3 to 64
> uhci_hcd 0000:00:1d.3: UHCI Host Controller
> PM: Adding info for No Bus:usbmon5
> uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
> uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
> PM: Adding info for usb:usb5
> PM: Adding info for No Bus:usbdev5.1_ep00
> usb usb5: configuration #1 chosen from 1 choice
> PM: Adding info for usb:5-0:1.0
> hub 5-0:1.0: USB hub found
> hub 5-0:1.0: 2 ports detected
> PM: Adding info for No Bus:usbdev5.1_ep81
> PM: Adding info for No Bus:usbdev5.1
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
> PM: Adding info for platform:i8042
> i8042.c: Detected active multiplexing controller, rev 1.1.
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX0 port at 0x60,0x64 irq 12
> PM: Adding info for serio:serio0
> serio: i8042 AUX1 port at 0x60,0x64 irq 12
> PM: Adding info for serio:serio1
> serio: i8042 AUX2 port at 0x60,0x64 irq 12
> PM: Adding info for serio:serio2
> serio: i8042 AUX3 port at 0x60,0x64 irq 12
> PM: Adding info for serio:serio3
> PM: Adding info for No Bus:mice
> PM: Adding info for serio:serio4
> PM: Adding info for No Bus:psaux
> mice: PS/2 mouse device common for all mice
> PM: Adding info for No Bus:event0
> PM: Adding info for No Bus:event1
> PM: Adding info for No Bus:event2
> PM: Adding info for No Bus:event3
> PM: Adding info for No Bus:input4
> input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
> PM: Adding info for No Bus:event4
> PM: Adding info for usb:1-8
> PM: Adding info for No Bus:usbdev1.2_ep00
> usb 1-8: configuration #1 chosen from 1 choice
> PM: Adding info for usb:1-8:1.0
> PM: Adding info for No Bus:usbdev1.2_ep81
> PM: Adding info for No Bus:usbdev1.2_ep82
> PM: Adding info for No Bus:usbdev1.2
> PM: Adding info for No Bus:rtc0
> rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
> PM: Removing info for No Bus:rtc0
> rtc_cmos: probe of 00:06 failed with error -16
> ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
> PM: Adding info for No Bus:i2c-0
> Bluetooth: HCI USB driver ver 2.9
> usbcore: registered new interface driver hci_usb
> Advanced Linux Sound Architecture Driver Version 1.0.14 (Fri Jul 20 09:12:58 2007 UTC).
> PM: Adding info for No Bus:timer
> PM: Adding info for No Bus:sequencer
> PM: Adding info for No Bus:sequencer2
> request_module: runaway loop modprobe net-pf-1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:seq
> ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
> PCI: Setting latency timer of device 0000:00:1b.0 to 64
> PM: Adding info for No Bus:card0
> PM: Adding info for No Bus:pcmC0D2c
> PM: Adding info for No Bus:pcmC0D0p
> PM: Adding info for No Bus:pcmC0D0c
> PM: Adding info for No Bus:dsp
> PM: Adding info for No Bus:audio
> PM: Adding info for No Bus:controlC0
> PM: Adding info for No Bus:mixer
> ALSA device list:
> #0: HDA Intel at 0xb0000000 irq 22
> ip_tables: (C) 2000-2006 Netfilter Core Team
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> Bluetooth: L2CAP ver 2.8
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> Bluetooth: RFCOMM ver 1.8
> ieee80211: 802.11 data/management/control stack, git-1.1.13
> ieee80211: Copyright (C) 2004-2005 Intel Corporation <[email protected]>
> ieee80211_crypt: registered algorithm 'NULL'
> ieee80211_crypt: registered algorithm 'WEP'
> Using IPI No-Shortcut mode
> swsusp: Resume From Partition /dev/sda5
> PM: Checking swsusp image.
> PM: Resume from disk failed.
> drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
> Freeing unused kernel memory: 200k freed
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04713/0x204000
> PM: Adding info for No Bus:input5
> input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input5
> PM: Adding info for No Bus:mouse0
> PM: Adding info for No Bus:event5
> Attempting manual resume
> swsusp: Resume From Partition 8:5
> PM: Checking swsusp image.
> PM: Resume from disk failed.
> swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
> swsusp: Basic memory bitmaps created
> swsusp: Basic memory bitmaps freed
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> NET: Registered protocol family 23
> iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 0.1.8k
> iwl3945: Copyright(c) 2003-2007 Intel Corporation
> PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:02:00.0 to 64
> iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
> PM: Adding info for No Bus:0000:02:00.0
> PM: Removing info for No Bus:0000:02:00.0
> ACPI: PCI Interrupt 0000:0a:09.2[A] -> GSI 20 (level, low) -> IRQ 20
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> PM: Adding info for platform:serial8250
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> PM: Adding info for No Bus:ttyS0
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
> PM: Adding info for No Bus:ttyS1
> PM: Adding info for No Bus:ttyS2
> PM: Adding info for No Bus:ttyS3
> PM: Removing info for No Bus:ttyS0
> 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> PM: Adding info for No Bus:ttyS0
> ACPI: PCI Interrupt 0000:0a:09.1[A] -> GSI 20 (level, low) -> IRQ 20
> nsc-ircc, chip->init
> nsc-ircc, Found chip at base=0x164e
> nsc-ircc, driver loaded (Dag Brattli)
> PM: Adding info for No Bus:irda0
> IrDA: Registered device irda0
> nsc-ircc, Found dongle: Supports SIR Mode only
> PM: Adding info for platform:nsc-ircc.0
> iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
> PM: Adding info for No Bus:phy0
> PM: Adding info for No Bus:wmaster0
> wmaster0: Selected rate control algorithm 'iwl-3945-rs'
> PM: Adding info for No Bus:wlan0
> udev: renamed network interface wlan0 to wireless
> firewire_ohci: Added fw-ohci device 0000:0a:09.1, OHCI version 1.10
> PM: Adding info for firewire:fw0
> firewire_core: created new fw device fw0 (0 config rom retries, S400)
> Adding 971892k swap on /dev/sda5. Priority:-1 extents:1 across:971892k
> EXT3 FS on sda6, internal journal
> PM: Adding info for platform:coretemp.0
> PM: Adding info for platform:coretemp.1
> fuse init (API version 7.8)
> PM: Adding info for No Bus:fuse
> pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
> pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
> pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
> PM: Adding info for No Bus:vcs2
> PM: Adding info for No Bus:vcsa2
> PM: Removing info for No Bus:vcs2
> PM: Removing info for No Bus:vcsa2
> PM: Adding info for No Bus:vcs3
> PM: Adding info for No Bus:vcsa3
> PM: Removing info for No Bus:vcs3
> PM: Removing info for No Bus:vcsa3
> PM: Adding info for No Bus:vcs4
> PM: Adding info for No Bus:vcsa4
> PM: Removing info for No Bus:vcs4
> PM: Removing info for No Bus:vcsa4
> PM: Adding info for No Bus:vcs5
> PM: Adding info for No Bus:vcsa5
> PM: Removing info for No Bus:vcs5
> PM: Removing info for No Bus:vcsa5
> PM: Adding info for No Bus:vcs2
> PM: Adding info for No Bus:vcsa2
> PM: Removing info for No Bus:vcs2
> PM: Removing info for No Bus:vcsa2
> PM: Adding info for No Bus:vcs3
> PM: Adding info for No Bus:vcsa3
> PM: Removing info for No Bus:vcs3
> PM: Removing info for No Bus:vcsa3
> PM: Adding info for No Bus:vcs4
> PM: Adding info for No Bus:vcsa4
> PM: Removing info for No Bus:vcs4
> PM: Removing info for No Bus:vcsa4
> PM: Adding info for No Bus:vcs5
> PM: Adding info for No Bus:vcsa5
> PM: Removing info for No Bus:vcs5
> PM: Removing info for No Bus:vcsa5
> PM: Adding info for No Bus:vcs6
> PM: Adding info for No Bus:vcsa6
> PM: Removing info for No Bus:vcs6
> PM: Removing info for No Bus:vcsa6
> PM: Adding info for No Bus:vcs2
> PM: Adding info for No Bus:vcsa2
> PM: Removing info for No Bus:vcs2
> PM: Removing info for No Bus:vcsa2
> PM: Adding info for No Bus:vcs2
> PM: Adding info for No Bus:vcsa2
> PM: Removing info for No Bus:vcs2
> PM: Removing info for No Bus:vcsa2
> PM: Adding info for No Bus:vcs2
> PM: Adding info for No Bus:vcsa2
> PM: Removing info for No Bus:vcs2
> PM: Removing info for No Bus:vcsa2
> PM: Adding info for No Bus:vcs3
> PM: Adding info for No Bus:vcsa3
> PM: Removing info for No Bus:vcs3
> PM: Removing info for No Bus:vcsa3
> PM: Adding info for No Bus:vcs3
> PM: Adding info for No Bus:vcsa3
> PM: Removing info for No Bus:vcs3
> PM: Removing info for No Bus:vcsa3
> PM: Adding info for No Bus:vcs3
> PM: Adding info for No Bus:vcsa3
> PM: Removing info for No Bus:vcs3
> PM: Removing info for No Bus:vcsa3
> PM: Adding info for No Bus:vcs4
> PM: Adding info for No Bus:vcsa4
> PM: Removing info for No Bus:vcs4
> PM: Removing info for No Bus:vcsa4
> PM: Adding info for No Bus:vcs4
> PM: Adding info for No Bus:vcsa4
> PM: Removing info for No Bus:vcs4
> PM: Removing info for No Bus:vcsa4
> PM: Adding info for No Bus:vcs4
> PM: Adding info for No Bus:vcsa4
> PM: Removing info for No Bus:vcs4
> PM: Removing info for No Bus:vcsa4
> PM: Adding info for No Bus:vcs5
> PM: Adding info for No Bus:vcsa5
> PM: Removing info for No Bus:vcs5
> PM: Removing info for No Bus:vcsa5
> PM: Adding info for No Bus:vcs5
> PM: Adding info for No Bus:vcsa5
> PM: Removing info for No Bus:vcs5
> PM: Removing info for No Bus:vcsa5
> PM: Adding info for No Bus:vcs5
> PM: Adding info for No Bus:vcsa5
> PM: Removing info for No Bus:vcs5
> PM: Removing info for No Bus:vcsa5
> PM: Adding info for No Bus:vcs6
> PM: Adding info for No Bus:vcsa6
> PM: Removing info for No Bus:vcs6
> PM: Removing info for No Bus:vcsa6
> PM: Adding info for No Bus:vcs6
> PM: Adding info for No Bus:vcsa6
> PM: Removing info for No Bus:vcs6
> PM: Removing info for No Bus:vcsa6
> PM: Adding info for No Bus:vcs6
> PM: Adding info for No Bus:vcsa6
> PM: Removing info for No Bus:vcs6
> PM: Removing info for No Bus:vcsa6
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> PM: Removing info for No Bus:vcs1
> PM: Removing info for No Bus:vcsa1
> PM: Adding info for No Bus:vcs1
> PM: Adding info for No Bus:vcsa1
> wireless: Initial auth_alg=0
> wireless: authenticate with AP 00:1b:2f:50:ac:26
> wireless: RX authentication from 00:1b:2f:50:ac:26 (alg=0 transaction=2 status=0)
> wireless: authenticated
> wireless: associate with AP 00:1b:2f:50:ac:26
> wireless: RX AssocResp from 00:1b:2f:50:ac:26 (capab=0x431 status=0 aid=1)
> wireless: associated
> wireless: CTS protection enabled (BSSID=00:1b:2f:50:ac:26)
> wireless: CTS protection disabled (BSSID=00:1b:2f:50:ac:26)
> wireless: CTS protection enabled (BSSID=00:1b:2f:50:ac:26)
> PM: Adding info for No Bus:vcs7
> PM: Adding info for No Bus:vcsa7
> PM: Removing info for No Bus:vcs7
> PM: Removing info for No Bus:vcsa7
> PM: Adding info for No Bus:vcs7
> PM: Adding info for No Bus:vcsa7
> PM: Adding info for No Bus:vcs2
> PM: Adding info for No Bus:vcsa2
> PM: Adding info for No Bus:vcs3
> PM: Adding info for No Bus:vcsa3
> PM: Adding info for No Bus:vcs4
> PM: Adding info for No Bus:vcsa4
> PM: Adding info for No Bus:vcs5
> PM: Adding info for No Bus:vcsa5
> PM: Adding info for No Bus:vcs6
> PM: Adding info for No Bus:vcsa6
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
