Finally.
This driver is for bf548 on chip ATAPI controller.
Both PIO 4 and UDMA5 mode are enabled.
Signed-off-by: Sonic Zhang <[email protected]>
---
drivers/ata/Kconfig | 28 +
drivers/ata/Makefile | 1 +
drivers/ata/pata_bf54x.c | 1585 ++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1614 insertions(+), 0 deletions(-)
create mode 100644 drivers/ata/pata_bf54x.c
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index b4a8d60..e679f04 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -583,4 +583,32 @@ config PATA_SCC
If unsure, say N.
+config PATA_BF54X
+ tristate "Blackfin 54x ATAPI support"
+ depends on BF542 || BF548 || BF549
+ help
+ This option enables support for the built-in ATAPI controller on
+ Blackfin 54x family chips.
+
+ If unsure, say N.
+
+choice
+ prompt "Blackfin 54x ATAPI mode"
+ depends on PATA_BF54X
+ default PATA_BF54X_DMA
+ help
+ This option selects bf54x ATAPI controller working mode.
+
+config PATA_BF54X_PIO
+ bool "PIO mode"
+ help
+ Blackfin ATAPI controller works under PIO mode.
+
+config PATA_BF54X_DMA
+ bool "DMA mode"
+ help
+ Blackfin ATAPI controller works under DMA mode.
+
+endchoice
+
endif # ATA
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 8149c68..c2ecba5 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_PATA_SIS) += pata_sis.o
obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o
obj-$(CONFIG_PATA_IXP4XX_CF) += pata_ixp4xx_cf.o
obj-$(CONFIG_PATA_SCC) += pata_scc.o
+obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o
# Should be last but one libata driver
diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c
new file mode 100644
index 0000000..e1236ea
--- /dev/null
+++ b/drivers/ata/pata_bf54x.c
@@ -0,0 +1,1585 @@
+/*
+ * File: drivers/ata/pata_bf54x.c
+ * Author: Sonic Zhang <[email protected]>
+ *
+ * Created:
+ * Description: ATAPI Driver for blackfin 54x
+ *
+ * Modified:
+ * Copyright 2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+#include <asm/dma.h>
+#include <asm/gpio.h>
+#include <asm/portmux.h>
+
+#define DRV_NAME "bf54x-atapi"
+#define DRV_VERSION "0.6"
+
+#define ATA_REG_CTRL 0x0E
+#define ATA_REG_ALTSTATUS ATA_REG_CTRL
+
+#define ATAPI_OFFSET_CONTROL 0x00
+#define ATAPI_OFFSET_STATUS 0x04
+#define ATAPI_OFFSET_DEV_ADDR 0x08
+#define ATAPI_OFFSET_DEV_TXBUF 0x0c
+#define ATAPI_OFFSET_DEV_RXBUF 0x10
+#define ATAPI_OFFSET_INT_MASK 0x14
+#define ATAPI_OFFSET_INT_STATUS 0x18
+#define ATAPI_OFFSET_XFER_LEN 0x1c
+#define ATAPI_OFFSET_LINE_STATUS 0x20
+#define ATAPI_OFFSET_SM_STATE 0x24
+#define ATAPI_OFFSET_TERMINATE 0x28
+#define ATAPI_OFFSET_PIO_TFRCNT 0x2c
+#define ATAPI_OFFSET_DMA_TFRCNT 0x30
+#define ATAPI_OFFSET_UMAIN_TFRCNT 0x34
+#define ATAPI_OFFSET_UDMAOUT_TFRCNT 0x38
+#define ATAPI_OFFSET_REG_TIM_0 0x40
+#define ATAPI_OFFSET_PIO_TIM_0 0x44
+#define ATAPI_OFFSET_PIO_TIM_1 0x48
+#define ATAPI_OFFSET_MULTI_TIM_0 0x50
+#define ATAPI_OFFSET_MULTI_TIM_1 0x54
+#define ATAPI_OFFSET_MULTI_TIM_2 0x58
+#define ATAPI_OFFSET_ULTRA_TIM_0 0x60
+#define ATAPI_OFFSET_ULTRA_TIM_1 0x64
+#define ATAPI_OFFSET_ULTRA_TIM_2 0x68
+#define ATAPI_OFFSET_ULTRA_TIM_3 0x6c
+
+
+#define ATAPI_GET_CONTROL(base)\
+ bfin_read16(base + ATAPI_OFFSET_CONTROL)
+#define ATAPI_SET_CONTROL(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_CONTROL, val)
+#define ATAPI_GET_STATUS(base)\
+ bfin_read16(base + ATAPI_OFFSET_STATUS)
+#define ATAPI_GET_DEV_ADDR(base)\
+ bfin_read16(base + ATAPI_OFFSET_DEV_ADDR)
+#define ATAPI_SET_DEV_ADDR(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_DEV_ADDR, val)
+#define ATAPI_GET_DEV_TXBUF(base)\
+ bfin_read16(base + ATAPI_OFFSET_DEV_TXBUF)
+#define ATAPI_SET_DEV_TXBUF(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_DEV_TXBUF, val)
+#define ATAPI_GET_DEV_RXBUF(base)\
+ bfin_read16(base + ATAPI_OFFSET_DEV_RXBUF)
+#define ATAPI_SET_DEV_RXBUF(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_DEV_RXBUF, val)
+#define ATAPI_GET_INT_MASK(base)\
+ bfin_read16(base + ATAPI_OFFSET_INT_MASK)
+#define ATAPI_SET_INT_MASK(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_INT_MASK, val)
+#define ATAPI_GET_INT_STATUS(base)\
+ bfin_read16(base + ATAPI_OFFSET_INT_STATUS)
+#define ATAPI_SET_INT_STATUS(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_INT_STATUS, val)
+#define ATAPI_GET_XFER_LEN(base)\
+ bfin_read16(base + ATAPI_OFFSET_XFER_LEN)
+#define ATAPI_SET_XFER_LEN(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_XFER_LEN, val)
+#define ATAPI_GET_LINE_STATUS(base)\
+ bfin_read16(base + ATAPI_OFFSET_LINE_STATUS)
+#define ATAPI_GET_SM_STATE(base)\
+ bfin_read16(base + ATAPI_OFFSET_SM_STATE)
+#define ATAPI_GET_TERMINATE(base)\
+ bfin_read16(base + ATAPI_OFFSET_TERMINATE)
+#define ATAPI_SET_TERMINATE(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_TERMINATE, val)
+#define ATAPI_GET_PIO_TFRCNT(base)\
+ bfin_read16(base + ATAPI_OFFSET_PIO_TFRCNT)
+#define ATAPI_GET_DMA_TFRCNT(base)\
+ bfin_read16(base + ATAPI_OFFSET_DMA_TFRCNT)
+#define ATAPI_GET_UMAIN_TFRCNT(base)\
+ bfin_read16(base + ATAPI_OFFSET_UMAIN_TFRCNT)
+#define ATAPI_GET_UDMAOUT_TFRCNT(base)\
+ bfin_read16(base + ATAPI_OFFSET_UDMAOUT_TFRCNT)
+#define ATAPI_GET_REG_TIM_0(base)\
+ bfin_read16(base + ATAPI_OFFSET_REG_TIM_0)
+#define ATAPI_SET_REG_TIM_0(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_REG_TIM_0, val)
+#define ATAPI_GET_PIO_TIM_0(base)\
+ bfin_read16(base + ATAPI_OFFSET_PIO_TIM_0)
+#define ATAPI_SET_PIO_TIM_0(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_PIO_TIM_0, val)
+#define ATAPI_GET_PIO_TIM_1(base)\
+ bfin_read16(base + ATAPI_OFFSET_PIO_TIM_1)
+#define ATAPI_SET_PIO_TIM_1(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_PIO_TIM_1, val)
+#define ATAPI_GET_MULTI_TIM_0(base)\
+ bfin_read16(base + ATAPI_OFFSET_MULTI_TIM_0)
+#define ATAPI_SET_MULTI_TIM_0(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_MULTI_TIM_0, val)
+#define ATAPI_GET_MULTI_TIM_1(base)\
+ bfin_read16(base + ATAPI_OFFSET_MULTI_TIM_1)
+#define ATAPI_SET_MULTI_TIM_1(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_MULTI_TIM_1, val)
+#define ATAPI_GET_MULTI_TIM_2(base)\
+ bfin_read16(base + ATAPI_OFFSET_MULTI_TIM_2)
+#define ATAPI_SET_MULTI_TIM_2(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_MULTI_TIM_2, val)
+#define ATAPI_GET_ULTRA_TIM_0(base)\
+ bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_0)
+#define ATAPI_SET_ULTRA_TIM_0(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_0, val)
+#define ATAPI_GET_ULTRA_TIM_1(base)\
+ bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_1)
+#define ATAPI_SET_ULTRA_TIM_1(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_1, val)
+#define ATAPI_GET_ULTRA_TIM_2(base)\
+ bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_2)
+#define ATAPI_SET_ULTRA_TIM_2(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_2, val)
+#define ATAPI_GET_ULTRA_TIM_3(base)\
+ bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_3)
+#define ATAPI_SET_ULTRA_TIM_3(base, val)\
+ bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_3, val)
+
+/**
+ * PIO Mode - Frequency compatibility
+ */
+/* mode: 0 1 2 3 4 */
+static u32 pio_fsclk[] =
+{ 33333333, 33333333, 33333333, 33333333, 33333333 };
+
+/**
+ * MDMA Mode - Frequency compatibility
+ */
+/* mode: 0 1 2 */
+static u32 mdma_fsclk[] = { 33333333, 33333333, 33333333 };
+
+/**
+ * UDMA Mode - Frequency compatibility
+ *
+ * UDMA5 - 100 MB/s - SCLK = 133 MHz
+ * UDMA4 - 66 MB/s - SCLK >= 80 MHz
+ * UDMA3 - 44.4 MB/s - SCLK >= 50 MHz
+ * UDMA2 - 33 MB/s - SCLK >= 40 MHz
+ */
+/* mode: 0 1 2 3 4 5 */
+static u32 udma_fsclk[] =
+{ 33333333, 33333333, 40000000, 50000000, 80000000, 133333333 };
+
+/**
+ * Register transfer timing table
+ */
+/* mode: 0 1 2 3 4 */
+/* Cycle Time */
+static u32 reg_t0min[] = { 600, 383, 330, 180, 120 };
+/* DIOR/DIOW to end cycle */
+static u32 reg_t2min[] = { 290, 290, 290, 70, 25 };
+/* DIOR/DIOW asserted pulse width */
+static u32 reg_teocmin[] = { 290, 290, 290, 80, 70 };
+
+/**
+ * PIO timing table
+ */
+/* mode: 0 1 2 3 4 */
+/* Cycle Time */
+static u32 pio_t0min[] = { 600, 383, 240, 180, 120 };
+/* Address valid to DIOR/DIORW */
+static u32 pio_t1min[] = { 70, 50, 30, 30, 25 };
+/* DIOR/DIOW to end cycle */
+static u32 pio_t2min[] = { 165, 125, 100, 80, 70 };
+/* DIOR/DIOW asserted pulse width */
+static u32 pio_teocmin[] = { 165, 125, 100, 70, 25 };
+/* DIOW data hold */
+static u32 pio_t4min[] = { 30, 20, 15, 10, 10 };
+
+/* ******************************************************************
+ * Multiword DMA timing table
+ * ******************************************************************
+ */
+/* mode: 0 1 2 */
+/* Cycle Time */
+static u32 mdma_t0min[] = { 480, 150, 120 };
+/* DIOR/DIOW asserted pulse width */
+static u32 mdma_tdmin[] = { 215, 80, 70 };
+/* DMACK to read data released */
+static u32 mdma_thmin[] = { 20, 15, 10 };
+/* DIOR/DIOW to DMACK hold */
+static u32 mdma_tjmin[] = { 20, 5, 5 };
+/* DIOR negated pulse width */
+static u32 mdma_tkrmin[] = { 50, 50, 25 };
+/* DIOR negated pulse width */
+static u32 mdma_tkwmin[] = { 215, 50, 25 };
+/* CS[1:0] valid to DIOR/DIOW */
+static u32 mdma_tmmin[] = { 50, 30, 25 };
+/* DMACK to read data released */
+static u32 mdma_tzmax[] = { 20, 25, 25 };
+
+/**
+ * Ultra DMA timing table
+ */
+/* mode: 0 1 2 3 4 5 */
+static u32 udma_tcycmin[] = { 112, 73, 54, 39, 25, 17 };
+static u32 udma_tdvsmin[] = { 70, 48, 31, 20, 7, 5 };
+static u32 udma_tenvmax[] = { 70, 70, 70, 55, 55, 50 };
+static u32 udma_trpmin[] = { 160, 125, 100, 100, 100, 85 };
+static u32 udma_tmin[] = { 5, 5, 5, 5, 3, 3 };
+
+
+static u32 udma_tmlimin = 20;
+static u32 udma_tzahmin = 20;
+static u32 udma_tenvmin = 20;
+static u32 udma_tackmin = 20;
+static u32 udma_tssmin = 50;
+
+/**
+ *
+ * Function: num_clocks_min
+ *
+ * Description:
+ * calculate number of SCLK cycles to meet minimum timing
+ */
+static unsigned short num_clocks_min(unsigned long tmin,
+ unsigned long fsclk)
+{
+ unsigned long tmp ;
+ unsigned short result;
+
+ tmp = tmin * (fsclk/1000/1000) / 1000;
+ result = (unsigned short)tmp;
+ if ((tmp*1000*1000) < (tmin*(fsclk/1000))) {
+ result++;
+ }
+
+ return result;
+}
+
+/**
+ * bfin_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void bfin_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ int mode = adev->pio_mode - XFER_PIO_0;
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ unsigned int fsclk = get_sclk();
+ unsigned short teoc_reg, t2_reg, teoc_pio;
+ unsigned short t4_reg, t2_pio, t1_reg;
+ unsigned short n0, n6, t6min = 5;
+
+ /* the most restrictive timing value is t6 and tc, the DIOW - data hold
+ * If one SCLK pulse is longer than this minimum value then register
+ * transfers cannot be supported at this frequency.
+ */
+ n6 = num_clocks_min(t6min, fsclk);
+ if (mode >= 0 && mode <= 4 && n6 >= 1) {
+ pr_debug("set piomode: mode=%d, fsclk=%ud\n", mode, fsclk);
+ /* calculate the timing values for register transfers. */
+ while (mode > 0 && pio_fsclk[mode] > fsclk) {
+ mode--;
+ }
+
+ /* DIOR/DIOW to end cycle time */
+ t2_reg = num_clocks_min(reg_t2min[mode], fsclk);
+ /* DIOR/DIOW asserted pulse width */
+ teoc_reg = num_clocks_min(reg_teocmin[mode], fsclk);
+ /* Cycle Time */
+ n0 = num_clocks_min(reg_t0min[mode], fsclk);
+
+ /* increase t2 until we meed the minimum cycle length */
+ while ((t2_reg + teoc_reg) < n0) {
+ t2_reg++;
+ }
+
+ /* calculate the timing values for pio transfers. */
+
+ /* DIOR/DIOW to end cycle time */
+ t2_pio = num_clocks_min(pio_t2min[mode], fsclk);
+ /* DIOR/DIOW asserted pulse width */
+ teoc_pio = num_clocks_min(pio_teocmin[mode], fsclk);
+ /* Cycle Time */
+ n0 = num_clocks_min(pio_t0min[mode], fsclk);
+
+ /* increase t2 until we meed the minimum cycle length */
+ while ((t2_pio + teoc_pio) < n0) {
+ t2_pio++;
+ }
+
+ /* Address valid to DIOR/DIORW */
+ t1_reg = num_clocks_min(pio_t1min[mode], fsclk);
+
+ /* DIOW data hold */
+ t4_reg = num_clocks_min(pio_t4min[mode], fsclk);
+
+ ATAPI_SET_REG_TIM_0(base, (teoc_reg<<8 | t2_reg));
+ ATAPI_SET_PIO_TIM_0(base, (t4_reg<<12 | t2_pio<<4 | t1_reg));
+ ATAPI_SET_PIO_TIM_1(base, teoc_pio);
+ if (mode > 2) {
+ ATAPI_SET_CONTROL(base,
+ ATAPI_GET_CONTROL(base) | IORDY_EN);
+ } else {
+ ATAPI_SET_CONTROL(base,
+ ATAPI_GET_CONTROL(base) & ~IORDY_EN);
+ }
+
+ /* Disable host ATAPI PIO interrupts */
+ ATAPI_SET_INT_MASK(base, ATAPI_GET_INT_MASK(base)
+ & ~(PIO_DONE_MASK | HOST_TERM_XFER_MASK));
+ SSYNC();
+ }
+}
+
+/**
+ * bfin_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ * @udma: udma mode, 0 - 6
+ *
+ * Set UDMA mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void bfin_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ int mode;
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ unsigned long fsclk = get_sclk();
+ unsigned short tenv, tack, tcyc_tdvs, tdvs, tmli, tss, trp, tzah;
+ unsigned short tm, td, tkr, tkw, teoc, th;
+ unsigned short n0, nf, tfmin = 5;
+ unsigned short nmin, tcyc;
+
+ mode = adev->dma_mode - XFER_UDMA_0;
+ if (mode >= 0 && mode <= 5) {
+ pr_debug("set udmamode: mode=%d\n", mode);
+ /* the most restrictive timing value is t6 and tc,
+ * the DIOW - data hold. If one SCLK pulse is longer
+ * than this minimum value then register
+ * transfers cannot be supported at this frequency.
+ */
+ while (mode > 0 && udma_fsclk[mode] > fsclk) {
+ mode--;
+ }
+ nmin = num_clocks_min(udma_tmin[mode], fsclk);
+ if (nmin >= 1) {
+ /* calculate the timing values for Ultra DMA. */
+ tdvs = num_clocks_min(udma_tdvsmin[mode], fsclk);
+ tcyc = num_clocks_min(udma_tcycmin[mode], fsclk);
+ tcyc_tdvs = 2;
+
+ /* increase tcyc - tdvs (tcyc_tdvs) until we meed
+ * the minimum cycle length
+ */
+ while ( (tdvs + tcyc_tdvs) < tcyc ) {
+ tcyc_tdvs++;
+ }
+
+ /* Mow assign the values required for the timing
+ * registers
+ */
+ if (tcyc_tdvs < 2) {
+ tcyc_tdvs = 2;
+ }
+
+ if (tdvs < 2) {
+ tdvs = 2;
+ }
+ tack = num_clocks_min(udma_tackmin, fsclk);
+ tss = num_clocks_min(udma_tssmin, fsclk);
+ tmli = num_clocks_min(udma_tmlimin, fsclk);
+ tzah = num_clocks_min(udma_tzahmin, fsclk);
+ trp = num_clocks_min(udma_trpmin[mode], fsclk);
+ tenv = num_clocks_min(udma_tenvmin, fsclk);
+ if (tenv <= udma_tenvmax[mode]) {
+ ATAPI_SET_ULTRA_TIM_0(base, (tenv<<8 | tack));
+ ATAPI_SET_ULTRA_TIM_1(base,
+ (tcyc_tdvs<<8 | tdvs));
+ ATAPI_SET_ULTRA_TIM_2(base, (tmli<<8 | tss));
+ ATAPI_SET_ULTRA_TIM_3(base, (trp<<8 | tzah));
+
+ /* Enable host ATAPI Untra DMA interrupts */
+ ATAPI_SET_INT_MASK(base,
+ ATAPI_GET_INT_MASK(base)
+ | UDMAIN_DONE_MASK
+ | UDMAOUT_DONE_MASK
+ | UDMAIN_TERM_MASK
+ | UDMAOUT_TERM_MASK);
+ }
+ }
+ }
+
+ mode = adev->dma_mode - XFER_MW_DMA_0;
+ if (mode >= 0 && mode <= 2) {
+ pr_debug("set mdmamode: mode=%d\n", mode);
+ /* the most restrictive timing value is tf, the DMACK to
+ * read data released. If one SCLK pulse is longer than
+ * this maximum value then the MDMA mode
+ * cannot be supported at this frequency.
+ */
+ while (mode > 0 && mdma_fsclk[mode] > fsclk) {
+ mode--;
+ }
+ nf = num_clocks_min(tfmin, fsclk);
+ if (nf >= 1) {
+ /* calculate the timing values for Multi-word DMA. */
+
+ /* DIOR/DIOW asserted pulse width */
+ td = num_clocks_min(mdma_tdmin[mode], fsclk);
+
+ /* DIOR negated pulse width */
+ tkw = num_clocks_min(mdma_tkwmin[mode], fsclk);
+
+ /* Cycle Time */
+ n0 = num_clocks_min(mdma_t0min[mode], fsclk);
+
+ /* increase tk until we meed the minimum cycle length */
+ while ( (tkw+td) < n0 ) {
+ tkw++;
+ }
+
+ /* DIOR negated pulse width - read */
+ tkr = num_clocks_min(mdma_tkrmin[mode], fsclk);
+ /* CS{1:0] valid to DIOR/DIOW */
+ tm = num_clocks_min(mdma_tmmin[mode], fsclk);
+ /* DIOR/DIOW to DMACK hold */
+ teoc = num_clocks_min(mdma_tjmin[mode], fsclk);
+ /* DIOW Data hold */
+ th = num_clocks_min(mdma_thmin[mode], fsclk);
+
+ ATAPI_SET_MULTI_TIM_0(base, (tm<<8 | td));
+ ATAPI_SET_MULTI_TIM_1(base, (tkr<<8 | tkw));
+ ATAPI_SET_MULTI_TIM_2(base, (teoc<<8 | th));
+
+ /* Enable host ATAPI Multi DMA interrupts */
+ ATAPI_SET_INT_MASK(base, ATAPI_GET_INT_MASK(base)
+ | MULTI_DONE_MASK | MULTI_TERM_MASK);
+ SSYNC();
+ }
+ }
+ return;
+}
+
+/**
+ *
+ * Function: wait_complete
+ *
+ * Description: Waits the interrupt from device
+ *
+ */
+static void inline wait_complete(unsigned long base, unsigned short mask)
+{
+ unsigned short status;
+
+ do {
+ status = ATAPI_GET_INT_STATUS(base) & mask;
+ } while (!status);
+
+ ATAPI_SET_INT_STATUS(base, mask);
+}
+
+/**
+ *
+ * Function: write_atapi_register
+ *
+ * Description: Writes to ATA Device Resgister
+ *
+ */
+
+static void write_atapi_register(unsigned long base,
+ unsigned long ata_reg, unsigned short value)
+{
+ /* Program the ATA_DEV_TXBUF register with write data (to be
+ * written into the device).
+ */
+ ATAPI_SET_DEV_TXBUF(base, value);
+
+ /* Program the ATA_DEV_ADDR register with address of the
+ * device register (0x01 to 0x0F).
+ */
+ ATAPI_SET_DEV_ADDR(base, ata_reg);
+
+ /* Program the ATA_CTRL register with dir set to write (1)
+ */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | XFER_DIR));
+
+ /* ensure PIO DMA is not set */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));
+
+ /* and start the transfer */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));
+
+ /* Wait for the interrupt to indicate the end of the transfer.
+ * (We need to wait on and clear rhe ATA_DEV_INT interrupt status)
+ */
+ wait_complete(base, PIO_DONE_INT);
+}
+
+/**
+ *
+ * Function: read_atapi_register
+ *
+ *Description: Reads from ATA Device Resgister
+ *
+ */
+
+static unsigned short read_atapi_register(unsigned long base,
+ unsigned long ata_reg)
+{
+ /* Program the ATA_DEV_ADDR register with address of the
+ * device register (0x01 to 0x0F).
+ */
+ ATAPI_SET_DEV_ADDR(base, ata_reg);
+
+ /* Program the ATA_CTRL register with dir set to read (0) and
+ */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~XFER_DIR));
+
+ /* ensure PIO DMA is not set */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));
+
+ /* and start the transfer */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));
+
+ /* Wait for the interrupt to indicate the end of the transfer.
+ * (PIO_DONE interrupt is set and it doesn't seem to matter
+ * that we don't clear it)
+ */
+ wait_complete(base, PIO_DONE_INT);
+
+ /* Read the ATA_DEV_RXBUF register with write data (to be
+ * written into the device).
+ */
+ return ATAPI_GET_DEV_RXBUF(base);
+}
+
+/**
+ *
+ * Function: write_atapi_register_data
+ *
+ * Description: Writes to ATA Device Resgister
+ *
+ */
+
+static void write_atapi_data(unsigned long base,
+ int len, unsigned short *buf)
+{
+ int i;
+
+ /* Set transfer length to 1 */
+ ATAPI_SET_XFER_LEN(base, 1);
+
+ /* Program the ATA_DEV_ADDR register with address of the
+ * ATA_REG_DATA
+ */
+ ATAPI_SET_DEV_ADDR(base, ATA_REG_DATA);
+
+ /* Program the ATA_CTRL register with dir set to write (1)
+ */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | XFER_DIR));
+
+ /* ensure PIO DMA is not set */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));
+
+ for (i = 0; i < len; i++) {
+ /* Program the ATA_DEV_TXBUF register with write data (to be
+ * written into the device).
+ */
+ ATAPI_SET_DEV_TXBUF(base, buf[i]);
+
+ /* and start the transfer */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));
+
+ /* Wait for the interrupt to indicate the end of the transfer.
+ * (We need to wait on and clear rhe ATA_DEV_INT
+ * interrupt status)
+ */
+ wait_complete(base, PIO_DONE_INT);
+ }
+}
+
+/**
+ *
+ * Function: read_atapi_register_data
+ *
+ * Description: Reads from ATA Device Resgister
+ *
+ */
+
+static void read_atapi_data(unsigned long base,
+ int len, unsigned short *buf)
+{
+ int i;
+
+ /* Set transfer length to 1 */
+ ATAPI_SET_XFER_LEN(base, 1);
+
+ /* Program the ATA_DEV_ADDR register with address of the
+ * ATA_REG_DATA
+ */
+ ATAPI_SET_DEV_ADDR(base, ATA_REG_DATA);
+
+ /* Program the ATA_CTRL register with dir set to read (0) and
+ */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~XFER_DIR));
+
+ /* ensure PIO DMA is not set */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));
+
+ for (i = 0; i < len; i++) {
+ /* and start the transfer */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));
+
+ /* Wait for the interrupt to indicate the end of the transfer.
+ * (PIO_DONE interrupt is set and it doesn't seem to matter
+ * that we don't clear it)
+ */
+ wait_complete(base, PIO_DONE_INT);
+
+ /* Read the ATA_DEV_RXBUF register with write data (to be
+ * written into the device).
+ */
+ buf[i] = ATAPI_GET_DEV_RXBUF(base);
+ }
+}
+
+/**
+ * bfin_tf_load - send taskfile registers to host controller
+ * @ap: Port to which output is sent
+ * @tf: ATA taskfile register set
+ *
+ * Note: Original code is ata_tf_load().
+ */
+
+static void bfin_tf_load (struct ata_port *ap, const struct ata_taskfile *tf)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ write_atapi_register(base, ATA_REG_CTRL, tf->ctl);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr) {
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ write_atapi_register(base, ATA_REG_FEATURE,
+ tf->hob_feature);
+ write_atapi_register(base, ATA_REG_NSECT,
+ tf->hob_nsect);
+ write_atapi_register(base, ATA_REG_LBAL, tf->hob_lbal);
+ write_atapi_register(base, ATA_REG_LBAM, tf->hob_lbam);
+ write_atapi_register(base, ATA_REG_LBAH, tf->hob_lbah);
+ pr_debug("hob: feat 0x%X nsect 0x%X, lba 0x%X "
+ "0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
+
+ write_atapi_register(base, ATA_REG_FEATURE, tf->feature);
+ write_atapi_register(base, ATA_REG_NSECT, tf->nsect);
+ write_atapi_register(base, ATA_REG_LBAL, tf->lbal);
+ write_atapi_register(base, ATA_REG_LBAM, tf->lbam);
+ write_atapi_register(base, ATA_REG_LBAH, tf->lbah);
+ pr_debug("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ write_atapi_register(base, ATA_REG_DEVICE, tf->device);
+ pr_debug("device 0x%X\n", tf->device);
+ }
+
+ ata_wait_idle(ap);
+}
+
+/**
+ * bfin_check_status - Read device status reg & clear interrupt
+ * @ap: port where the device is
+ *
+ * Note: Original code is ata_check_status().
+ */
+
+static u8 bfin_check_status (struct ata_port *ap)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ return read_atapi_register(base, ATA_REG_STATUS);
+}
+
+/**
+ * bfin_tf_read - input device's ATA taskfile shadow registers
+ * @ap: Port from which input is read
+ * @tf: ATA taskfile register set for storing input
+ *
+ * Note: Original code is ata_tf_read().
+ */
+
+static void bfin_tf_read (struct ata_port *ap, struct ata_taskfile *tf)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+
+ tf->command = bfin_check_status(ap);
+ tf->feature = read_atapi_register(base, ATA_REG_ERR);
+ tf->nsect = read_atapi_register(base, ATA_REG_NSECT);
+ tf->lbal = read_atapi_register(base, ATA_REG_LBAL);
+ tf->lbam = read_atapi_register(base, ATA_REG_LBAM);
+ tf->lbah = read_atapi_register(base, ATA_REG_LBAH);
+ tf->device = read_atapi_register(base, ATA_REG_DEVICE);
+
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ write_atapi_register(base, ATA_REG_CTRL, tf->ctl | ATA_HOB);
+ tf->hob_feature = read_atapi_register(base, ATA_REG_ERR);
+ tf->hob_nsect = read_atapi_register(base, ATA_REG_NSECT);
+ tf->hob_lbal = read_atapi_register(base, ATA_REG_LBAL);
+ tf->hob_lbam = read_atapi_register(base, ATA_REG_LBAM);
+ tf->hob_lbah = read_atapi_register(base, ATA_REG_LBAH);
+ }
+}
+
+/**
+ * bfin_exec_command - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Note: Original code is ata_exec_command().
+ */
+
+static void bfin_exec_command (struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ pr_debug("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+
+ write_atapi_register(base, ATA_REG_CMD, tf->command);
+ ata_pause(ap);
+}
+
+/**
+ * bfin_check_altstatus - Read device alternate status reg
+ * @ap: port where the device is
+ */
+
+static u8 bfin_check_altstatus (struct ata_port *ap)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ return read_atapi_register(base, ATA_REG_ALTSTATUS);
+}
+
+/**
+ * bfin_std_dev_select - Select device 0/1 on ATA bus
+ * @ap: ATA channel to manipulate
+ * @device: ATA device (numbered from zero) to select
+ *
+ * Note: Original code is ata_std_dev_select().
+ */
+
+static void bfin_std_dev_select (struct ata_port *ap, unsigned int device)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ u8 tmp;
+
+ if (device == 0)
+ tmp = ATA_DEVICE_OBS;
+ else
+ tmp = ATA_DEVICE_OBS | ATA_DEV1;
+
+ write_atapi_register(base, ATA_REG_DEVICE, tmp);
+ ata_pause(ap);
+}
+
+/**
+ * bfin_bmdma_setup - Set up IDE DMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * Note: Original code is ata_bmdma_setup().
+ */
+
+static void bfin_bmdma_setup (struct ata_queued_cmd *qc)
+{
+ unsigned short config = WDSIZE_16;
+ struct scatterlist *sg;
+
+ pr_debug("in atapi dma setup\n");
+ /* Program the ATA_CTRL register with dir */
+ if (qc->tf.flags & ATA_TFLAG_WRITE) {
+ /* fill the ATAPI DMA controller */
+ set_dma_config(CH_ATAPI_TX, config);
+ set_dma_x_modify(CH_ATAPI_TX, 2);
+ ata_for_each_sg(sg, qc) {
+ set_dma_start_addr(CH_ATAPI_TX, sg_dma_address(sg));
+ set_dma_x_count(CH_ATAPI_TX, sg_dma_len(sg) >> 1);
+ }
+ } else {
+ config |= WNR;
+ /* fill the ATAPI DMA controller */
+ set_dma_config(CH_ATAPI_RX, config);
+ set_dma_x_modify(CH_ATAPI_RX, 2);
+ ata_for_each_sg(sg, qc) {
+ set_dma_start_addr(CH_ATAPI_RX, sg_dma_address(sg));
+ set_dma_x_count(CH_ATAPI_RX, sg_dma_len(sg) >> 1);
+ }
+ }
+}
+
+/**
+ * bfin_bmdma_start - Start an IDE DMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * Note: Original code is ata_bmdma_start().
+ */
+
+static void bfin_bmdma_start (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ struct scatterlist *sg;
+
+ pr_debug("in atapi dma start\n");
+ if (ap->udma_mask || ap->mwdma_mask) {
+ /* start ATAPI DMA controller*/
+ if (qc->tf.flags & ATA_TFLAG_WRITE) {
+ ata_for_each_sg(sg, qc) {
+ flush_dcache_range(sg_dma_address(sg),
+ sg_dma_address(sg) + sg_dma_len(sg));
+ }
+ enable_dma(CH_ATAPI_TX);
+ pr_debug("enable udma write\n");
+
+ /* Send ATA DMA write command */
+ bfin_exec_command(ap, &qc->tf);
+
+ /* set ATA DMA write direction */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base)
+ | XFER_DIR));
+ } else {
+ enable_dma(CH_ATAPI_RX);
+ pr_debug("enable udma read\n");
+
+ /* Send ATA DMA read command */
+ bfin_exec_command(ap, &qc->tf);
+
+ /* set ATA DMA read direction */
+ ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base)
+ & ~XFER_DIR));
+ }
+
+ /* Reset all transfer count */
+ ATAPI_SET_CONTROL(base,
+ ATAPI_GET_CONTROL(base) | TFRCNT_RST);
+
+ /* Set transfer length to buffer len */
+ ata_for_each_sg(sg, qc) {
+ ATAPI_SET_XFER_LEN(base, (sg_dma_len(sg) >> 1));
+ }
+
+ /* Enable ATA DMA operation*/
+ if (ap->udma_mask) {
+ ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base)
+ | ULTRA_START);
+ } else {
+ ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base)
+ | MULTI_START);
+ }
+ }
+}
+
+/**
+ * bfin_bmdma_stop - Stop IDE DMA transfer
+ * @qc: Command we are ending DMA for
+ */
+
+static void bfin_bmdma_stop (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct scatterlist *sg;
+
+ pr_debug("in atapi dma stop\n");
+ if (ap->udma_mask || ap->mwdma_mask) {
+ /* stop ATAPI DMA controller*/
+ if (qc->tf.flags & ATA_TFLAG_WRITE) {
+ disable_dma(CH_ATAPI_TX);
+ } else {
+ disable_dma(CH_ATAPI_RX);
+ if (ap->hsm_task_state & HSM_ST_LAST) {
+ ata_for_each_sg(sg, qc) {
+ invalidate_dcache_range(
+ sg_dma_address(sg),
+ sg_dma_address(sg)
+ + sg_dma_len(sg));
+ }
+ }
+ }
+ }
+}
+
+/**
+ * bfin_devchk - PATA device presence detection
+ * @ap: ATA channel to examine
+ * @device: Device to examine (starting at zero)
+ *
+ * Note: Original code is ata_devchk().
+ */
+
+static unsigned int bfin_devchk (struct ata_port *ap,
+ unsigned int device)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ u8 nsect, lbal;
+
+ ap->ops->dev_select(ap, device);
+
+ write_atapi_register(base, ATA_REG_NSECT, 0x55);
+ write_atapi_register(base, ATA_REG_LBAL, 0xaa);
+
+ write_atapi_register(base, ATA_REG_NSECT, 0xaa);
+ write_atapi_register(base, ATA_REG_LBAL, 0x55);
+
+ write_atapi_register(base, ATA_REG_NSECT, 0x55);
+ write_atapi_register(base, ATA_REG_LBAL, 0xaa);
+
+ nsect = read_atapi_register(base, ATA_REG_NSECT);
+ lbal = read_atapi_register(base, ATA_REG_LBAL);
+
+ if ((nsect == 0x55) && (lbal == 0xaa))
+ return 1; /* we found a device */
+
+ return 0; /* nothing found */
+}
+
+/**
+ * bfin_bus_post_reset - PATA device post reset
+ *
+ * Note: Original code is ata_bus_post_reset().
+ */
+
+static void bfin_bus_post_reset (struct ata_port *ap, unsigned int devmask)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ unsigned int dev0 = devmask & (1 << 0);
+ unsigned int dev1 = devmask & (1 << 1);
+ unsigned long timeout;
+
+ /* if device 0 was found in ata_devchk, wait for its
+ * BSY bit to clear
+ */
+ if (dev0)
+ ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+
+ /* if device 1 was found in ata_devchk, wait for
+ * register access, then wait for BSY to clear
+ */
+ timeout = jiffies + ATA_TMOUT_BOOT;
+ while (dev1) {
+ u8 nsect, lbal;
+
+ ap->ops->dev_select(ap, 1);
+ nsect = read_atapi_register(base, ATA_REG_NSECT);
+ lbal = read_atapi_register(base, ATA_REG_LBAL);
+ if ((nsect == 1) && (lbal == 1))
+ break;
+ if (time_after(jiffies, timeout)) {
+ dev1 = 0;
+ break;
+ }
+ msleep(50); /* give drive a breather */
+ }
+ if (dev1)
+ ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+
+ /* is all this really necessary? */
+ ap->ops->dev_select(ap, 0);
+ if (dev1)
+ ap->ops->dev_select(ap, 1);
+ if (dev0)
+ ap->ops->dev_select(ap, 0);
+}
+
+/**
+ * bfin_bus_softreset - PATA device software reset
+ *
+ * Note: Original code is ata_bus_softreset().
+ */
+
+static unsigned int bfin_bus_softreset (struct ata_port *ap,
+ unsigned int devmask)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+
+ /* software reset. causes dev0 to be selected */
+ write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
+ udelay(20);
+ write_atapi_register(base, ATA_REG_CTRL, ap->ctl | ATA_SRST);
+ udelay(20);
+ write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
+
+ /* spec mandates ">= 2ms" before checking status.
+ * We wait 150ms, because that was the magic delay used for
+ * ATAPI devices in Hale Landis's ATADRVR, for the period of time
+ * between when the ATA command register is written, and then
+ * status is checked. Because waiting for "a while" before
+ * checking status is fine, post SRST, we perform this magic
+ * delay here as well.
+ *
+ * Old drivers/ide uses the 2mS rule and then waits for ready
+ */
+ msleep(150);
+
+ /* Before we perform post reset processing we want to see if
+ * the bus shows 0xFF because the odd clown forgets the D7
+ * pulldown resistor.
+ */
+ if (bfin_check_status(ap) == 0xFF)
+ return 0;
+
+ bfin_bus_post_reset(ap, devmask);
+
+ return 0;
+}
+
+/**
+ * bfin_std_softreset - reset host port via ATA SRST
+ * @ap: port to reset
+ * @classes: resulting classes of attached devices
+ *
+ * Note: Original code is ata_std_softreset().
+ */
+
+static int bfin_std_softreset(struct ata_port *ap, unsigned int *classes,
+ unsigned long deadline)
+{
+ unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
+ unsigned int devmask = 0, err_mask;
+ u8 err;
+
+ if (ata_port_offline(ap)) {
+ classes[0] = ATA_DEV_NONE;
+ goto out;
+ }
+
+ /* determine if device 0/1 are present */
+ if (bfin_devchk(ap, 0))
+ devmask |= (1 << 0);
+ if (slave_possible && bfin_devchk(ap, 1))
+ devmask |= (1 << 1);
+
+ /* select device 0 again */
+ ap->ops->dev_select(ap, 0);
+
+ /* issue bus reset */
+ err_mask = bfin_bus_softreset(ap, devmask);
+ if (err_mask) {
+ ata_port_printk(ap, KERN_ERR, "SRST failed (err_mask=0x%x)\n",
+ err_mask);
+ return -EIO;
+ }
+
+ /* determine by signature whether we have ATA or ATAPI devices */
+ classes[0] = ata_dev_try_classify(ap, 0, &err);
+ if (slave_possible && err != 0x81)
+ classes[1] = ata_dev_try_classify(ap, 1, &err);
+
+ out:
+ return 0;
+}
+
+/**
+ * bfin_bmdma_status - Read IDE DMA status
+ * @ap: Port associated with this ATA transaction.
+ */
+
+static unsigned char bfin_bmdma_status (struct ata_port *ap)
+{
+ unsigned char host_stat = 0;
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ unsigned short int_status = ATAPI_GET_INT_STATUS(base);
+
+ if (ATAPI_GET_STATUS(base) & (MULTI_XFER_ON|ULTRA_XFER_ON)) {
+ host_stat = ATA_DMA_ACTIVE;
+ }
+ if (int_status & (MULTI_DONE_INT|UDMAIN_DONE_INT|UDMAOUT_DONE_INT)) {
+ host_stat = ATA_DMA_INTR;
+ }
+ if (int_status & (MULTI_TERM_INT|UDMAIN_TERM_INT|UDMAOUT_TERM_INT)) {
+ host_stat = ATA_DMA_ERR;
+ }
+
+ return host_stat;
+}
+
+/**
+ * bfin_data_xfer - Transfer data by PIO
+ * @adev: device for this I/O
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @write_data: read/write
+ *
+ * Note: Original code is ata_data_xfer().
+ */
+
+static void bfin_data_xfer (struct ata_device *adev, unsigned char *buf,
+ unsigned int buflen, int write_data)
+{
+ struct ata_port *ap = adev->ap;
+ unsigned int words = buflen >> 1;
+ unsigned short *buf16 = (u16 *) buf;
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+
+ /* Transfer multiple of 2 bytes */
+ if (write_data) {
+ write_atapi_data(base, words, buf16);
+ } else {
+ read_atapi_data(base, words, buf16);
+ }
+
+ /* Transfer trailing 1 byte, if any. */
+ if (unlikely(buflen & 0x01)) {
+ unsigned short align_buf[1] = { 0 };
+ unsigned char *trailing_buf = buf + buflen - 1;
+
+ if (write_data) {
+ memcpy(align_buf, trailing_buf, 1);
+ write_atapi_data(base, 1, align_buf);
+ } else {
+ read_atapi_data(base, 1, align_buf);
+ memcpy(trailing_buf, align_buf, 1);
+ }
+ }
+}
+
+/**
+ * bfin_irq_on - Enable interrupts on a port.
+ * @ap: Port on which interrupts are enabled.
+ *
+ * Note: Original code is ata_irq_on().
+ */
+
+static unsigned char bfin_irq_on (struct ata_port *ap)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ u8 tmp;
+
+ pr_debug("in atapi irq on\n");
+ ap->ctl &= ~ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
+ tmp = ata_wait_idle(ap);
+
+ ap->ops->irq_clear(ap);
+
+ return tmp;
+}
+
+/**
+ * bfin_irq_ack - Acknowledge a device interrupt.
+ * @ap: Port on which interrupts are enabled.
+ *
+ * Note: Original code is ata_irq_ack().
+ */
+
+static unsigned char bfin_irq_ack (struct ata_port *ap, unsigned int chk_drq)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+ unsigned int bits = chk_drq ? ATA_BUSY | ATA_DRQ : ATA_BUSY;
+ unsigned char status;
+
+ pr_debug("in atapi irq ack\n");
+ status = ata_busy_wait(ap, bits, 1000);
+ if (status & bits)
+ if (ata_msg_err(ap))
+ dev_err(ap->dev, "abnormal status 0x%X\n", status);
+
+ /* get controller status; clear intr, err bits */
+ ATAPI_SET_INT_STATUS(base, ATAPI_GET_INT_STATUS(base)|ATAPI_DEV_INT
+ | MULTI_DONE_INT | UDMAIN_DONE_INT | UDMAOUT_DONE_INT
+ | MULTI_TERM_INT | UDMAIN_TERM_INT | UDMAOUT_TERM_INT);
+
+ return bfin_bmdma_status(ap);
+}
+
+/**
+ * bfin_bmdma_freeze - Freeze DMA controller port
+ * @ap: port to freeze
+ *
+ * Note: Original code is ata_bmdma_freeze().
+ */
+
+static void bfin_bmdma_freeze (struct ata_port *ap)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+
+ pr_debug("in atapi dma freeze\n");
+ ap->ctl |= ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
+
+ /* Under certain circumstances, some controllers raise IRQ on
+ * ATA_NIEN manipulation. Also, many controllers fail to mask
+ * previously pending IRQ on ATA_NIEN assertion. Clear it.
+ */
+ ata_chk_status(ap);
+
+ ap->ops->irq_clear(ap);
+}
+
+/**
+ * bfin_std_postreset - standard postreset callback
+ * @ap: the target ata_port
+ * @classes: classes of attached devices
+ *
+ * Note: Original code is ata_std_postreset().
+ */
+
+static void bfin_std_postreset (struct ata_port *ap, unsigned int *classes)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+
+ /* re-enable interrupts */
+ if (!ap->ops->error_handler)
+ ap->ops->irq_on(ap);
+
+ /* is double-select really necessary? */
+ if (classes[0] != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 1);
+ if (classes[1] != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 0);
+
+ /* bail out if no device is present */
+ if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
+ return;
+ }
+
+ /* set up device control */
+ write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
+}
+
+/**
+ * bfin_error_handler - Stock error handler for DMA controller
+ * @ap: port to handle error for
+ */
+
+static void bfin_error_handler (struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ata_std_prereset, bfin_std_softreset, NULL,
+ bfin_std_postreset);
+}
+
+/**
+ * bfin_bmdma_irq_clear - Clear ATAPI interrupt.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Note: Original code is ata_bmdma_irq_clear().
+ */
+
+static void bfin_bmdma_irq_clear (struct ata_port *ap)
+{
+ unsigned long base = (unsigned long)ap->ioaddr.ctl_addr;
+
+ pr_debug("in atapi irq clear\n");
+ ATAPI_SET_INT_STATUS(base, 0x1FF);
+}
+
+static void bfin_port_stop(struct ata_port *ap)
+{
+ pr_debug("in atapi port stop\n");
+ if (ap->udma_mask != 0 || ap->mwdma_mask != 0) {
+ free_dma(CH_ATAPI_RX);
+ free_dma(CH_ATAPI_TX);
+ }
+}
+
+static int bfin_port_start(struct ata_port *ap)
+{
+ pr_debug("in atapi port start\n");
+ if (ap->udma_mask != 0 || ap->mwdma_mask != 0) {
+ if (request_dma(CH_ATAPI_RX, "BFIN ATAPI RX DMA") >= 0) {
+ if (request_dma(CH_ATAPI_TX,
+ "BFIN ATAPI TX DMA") >= 0) {
+ return 0;
+ }
+ free_dma(CH_ATAPI_RX);
+ }
+ ap->udma_mask = 0;
+ ap->mwdma_mask = 0;
+ dev_err(ap->dev, "Unable to request ATAPI DMA!\n");
+ return -EBUSY;
+ }
+ return 0;
+}
+
+void bfin_qc_prep(struct ata_queued_cmd *qc)
+{
+}
+
+static struct scsi_host_template bfin_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+/* .sg_tablesize = LIBATA_MAX_PRD,*/
+ .sg_tablesize = SG_NONE,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+#ifdef CONFIG_PM
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
+#endif
+};
+
+static const struct ata_port_operations bfin_pata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = bfin_set_piomode,
+ .set_dmamode = bfin_set_dmamode,
+
+ .tf_load = bfin_tf_load,
+ .tf_read = bfin_tf_read,
+ .exec_command = bfin_exec_command,
+ .check_status = bfin_check_status,
+ .check_altstatus = bfin_check_altstatus,
+ .dev_select = bfin_std_dev_select,
+
+ .bmdma_setup = bfin_bmdma_setup,
+ .bmdma_start = bfin_bmdma_start,
+ .bmdma_stop = bfin_bmdma_stop,
+ .bmdma_status = bfin_bmdma_status,
+ .data_xfer = bfin_data_xfer,
+
+ .qc_prep = bfin_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .freeze = bfin_bmdma_freeze,
+ .error_handler = bfin_error_handler,
+ .post_internal_cmd = bfin_bmdma_stop,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = bfin_bmdma_irq_clear,
+ .irq_on = bfin_irq_on,
+ .irq_ack = bfin_irq_ack,
+
+ .port_start = bfin_port_start,
+ .port_stop = bfin_port_stop,
+};
+
+static struct ata_port_info bfin_port_info[] = {
+ {
+ .sht = &bfin_sht,
+ .flags = ATA_FLAG_SLAVE_POSS
+ | ATA_FLAG_MMIO
+ | ATA_FLAG_NO_LEGACY,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0,
+#ifdef CONFIG_PATA_BF54X_DMA
+ .udma_mask = ATA_UDMA5,
+#else
+ .udma_mask = 0,
+#endif
+ .port_ops = &bfin_pata_ops,
+ },
+};
+
+/**
+ * bfin_reset_controller - initialize BF54x ATAPI controller.
+ */
+
+static int bfin_reset_controller(struct ata_host *host)
+{
+ unsigned long base = (unsigned long)host->ports[0]->ioaddr.ctl_addr;
+ int count;
+ unsigned short status;
+
+ /* Disable all ATAPI interrupts */
+ ATAPI_SET_INT_MASK(base, 0);
+ SSYNC();
+
+ /* Assert the RESET signal 25us*/
+ ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | DEV_RST);
+ udelay(30);
+
+ /* Negate the RESET signal for 2ms*/
+ ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) & ~DEV_RST);
+ udelay(2100);
+
+ /* Wait on Busy flag to clear */
+ count = 10000000;
+ do {
+ status = read_atapi_register(base, ATA_REG_STATUS);
+ } while (count-- && (status & ATA_BUSY));
+
+ /* Enable only ATAPI Device interrupt */
+ ATAPI_SET_INT_MASK(base, 1);
+ SSYNC();
+
+ return (!count);
+}
+
+/**
+ * atapi_io_port - define atapi peripheral port pins.
+ */
+static unsigned short atapi_io_port[] = {
+ P_ATAPI_RESET,
+ P_ATAPI_DIOR,
+ P_ATAPI_DIOW,
+ P_ATAPI_CS0,
+ P_ATAPI_CS1,
+ P_ATAPI_DMACK,
+ P_ATAPI_DMARQ,
+ P_ATAPI_INTRQ,
+ P_ATAPI_IORDY,
+ 0
+};
+
+/**
+ * bfin_atapi_probe - attach a bfin atapi interface
+ * @pdev: platform device
+ *
+ * Register a bfin atapi interface.
+ *
+ *
+ * Platform devices are expected to contain 2 resources per port:
+ *
+ * - I/O Base (IORESOURCE_IO)
+ * - IRQ (IORESOURCE_IRQ)
+ *
+ */
+static int __devinit bfin_atapi_probe(struct platform_device *pdev)
+{
+ int board_idx = 0;
+ struct resource *res;
+ struct ata_host *host;
+ const struct ata_port_info *ppi[] =
+ { &bfin_port_info[board_idx], NULL };
+
+ /*
+ * Simple resource validation ..
+ */
+ if (unlikely(pdev->num_resources != 2)) {
+ dev_err(&pdev->dev, "invalid number of resources\n");
+ return -EINVAL;
+ }
+
+ /*
+ * Get the register base first
+ */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL)
+ return -EINVAL;
+
+ /*
+ * Now that that's out of the way, wire up the port..
+ */
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 1);
+ if (!host)
+ return -ENOMEM;
+
+ host->ports[0]->ioaddr.ctl_addr = (void *)res->start;
+
+ if (peripheral_request_list(atapi_io_port, "atapi-io-port")) {
+ dev_err(&pdev->dev, "Requesting Peripherals faild\n");
+ return -EFAULT;
+ }
+
+ if (bfin_reset_controller(host)) {
+ peripheral_free_list(atapi_io_port);
+ dev_err(&pdev->dev, "Fail to reset ATAPI device\n");
+ return -EFAULT;
+ }
+
+ if (ata_host_activate(host, platform_get_irq(pdev, 0),
+ ata_interrupt, IRQF_SHARED, &bfin_sht) != 0) {
+ peripheral_free_list(atapi_io_port);
+ dev_err(&pdev->dev, "Fail to attach ATAPI device\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+/**
+ * bfin_atapi_remove - unplug a bfin atapi interface
+ * @pdev: platform device
+ *
+ * A bfin atapi device has been unplugged. Perform the needed
+ * cleanup. Also called on module unload for any active devices.
+ */
+static int __devexit bfin_atapi_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ata_host *host = dev_get_drvdata(dev);
+
+ ata_host_detach(host);
+
+ peripheral_free_list(atapi_io_port);
+
+ return 0;
+}
+
+static struct platform_driver bfin_atapi_driver = {
+ .probe = bfin_atapi_probe,
+ .remove = __devexit_p(bfin_atapi_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init bfin_atapi_init (void)
+{
+ pr_info("register bfin atapi driver\n");
+ return platform_driver_register(&bfin_atapi_driver);
+}
+
+static void __exit bfin_atapi_exit (void)
+{
+ platform_driver_unregister(&bfin_atapi_driver);
+}
+
+module_init(bfin_atapi_init);
+module_exit(bfin_atapi_exit);
+
+MODULE_AUTHOR("Sonic Zhang <[email protected]>");
+MODULE_DESCRIPTION("ATAPI libata driver for blackfin 54x ATAPI controller");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
--
1.5.1.3
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
