[PATCH 2] Merge the Sonics Silicon Backplane subsystem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The Sonics Silicon Backplane is a mini-bus used on
various Broadcom chips and embedded devices.
Devices using the SSB include b44, bcm43xx and various
Broadcom based wireless routers.
A b44 and bcm43xx port and a SSB based OHCI driver is available.

Patch #2: This includes a compilation fix for nondebug build (d'oh)
and various small fixes based on comments.

Signed-off-by: Michael Buesch <[email protected]>
Acked-by: John Linville <[email protected]>

diff --git a/drivers/Makefile b/drivers/Makefile
index a9e4c5f..2b079ed 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -87,3 +87,4 @@ obj-$(CONFIG_DMA_ENGINE)	+= dma/
 obj-$(CONFIG_HID)		+= hid/
 obj-$(CONFIG_PPC_PS3)		+= ps3/
 obj-$(CONFIG_OF)		+= of/
+obj-$(CONFIG_SSB)		+= ssb/
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 3e1c442..7bdae47 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -58,6 +58,8 @@ source "drivers/power/Kconfig"
 
 source "drivers/hwmon/Kconfig"
 
+source "drivers/ssb/Kconfig"
+
 source "drivers/mfd/Kconfig"
 
 source "drivers/media/Kconfig"
diff --git a/drivers/ssb/Makefile b/drivers/ssb/Makefile
new file mode 100644
index 0000000..045aff0
--- /dev/null
+++ b/drivers/ssb/Makefile
@@ -0,0 +1,13 @@
+# core
+ssb-y					+= main.o scan.o
+
+# host support
+ssb-$(CONFIG_SSB_PCIHOST)		+= pci.o pcihost_wrapper.o
+ssb-$(CONFIG_SSB_PCMCIAHOST)		+= pcmcia.o
+
+# built-in drivers
+ssb-y					+= driver_chipcommon.o
+ssb-$(CONFIG_SSB_DRIVER_MIPS)		+= driver_mipscore.o
+ssb-$(CONFIG_SSB_DRIVER_PCICORE)	+= driver_pcicore.o
+
+obj-$(CONFIG_SSB)			+= ssb.o
diff --git a/drivers/ssb/Kconfig b/drivers/ssb/Kconfig
new file mode 100644
index 0000000..34a9411
--- /dev/null
+++ b/drivers/ssb/Kconfig
@@ -0,0 +1,92 @@
+menu "Sonics Silicon Backplane"
+
+config SSB
+	tristate "Sonics Silicon Backplane support"
+	depends on EXPERIMENTAL
+	help
+	  Support for the Sonics Silicon Backplane bus
+
+	  The module will be called ssb
+
+	  If unsure, say M
+
+config SSB_PCIHOST
+	bool "Support for SSB on PCI-bus host"
+	depends on SSB && PCI
+	default y
+	help
+	  Support for a Sonics Silicon Backplane on top
+	  of a PCI device.
+
+	  If unsure, say Y
+
+config SSB_PCMCIAHOST
+	bool "Support for SSB on PCMCIA-bus host"
+	depends on SSB && PCMCIA
+	help
+	  Support for a Sonics Silicon Backplane on top
+	  of a PCMCIA device.
+
+	  If unsure, say N
+
+config SSB_SILENT
+	bool "No SSB kernel messages"
+	depends on SSB
+	help
+	  This option turns off all Sonics Silicon Backplane printks.
+	  Note that you won't be able to identify problems, once
+	  messages are turned off.
+	  This might only be desired for production kernels on
+	  embedded devices to reduce the kernel size.
+
+	  Say N
+
+config SSB_DEBUG
+	bool "SSB debugging"
+	depends on SSB && !SSB_SILENT
+	help
+	  This turns on additional runtime checks and debugging
+	  messages. Turn this on for SSB troubleshooting.
+
+	  If unsure, say N
+
+config SSB_SERIAL
+	bool
+	depends on SSB
+	# ChipCommon and ExtIf serial support routines.
+
+config SSB_DRIVER_PCICORE
+	bool "SSB PCI core driver"
+	depends on SSB && SSB_PCIHOST
+	help
+	  Driver for the Sonics Silicon Backplane attached
+	  Broadcom PCI core.
+
+	  If unsure, say Y
+
+config SSB_PCICORE_HOSTMODE
+	bool "Hostmode support for SSB PCI core"
+	depends on SSB_DRIVER_PCICORE && SSB_DRIVER_MIPS
+	help
+	  PCIcore hostmode operation (external PCI bus).
+
+config SSB_DRIVER_MIPS
+	bool "SSB Broadcom MIPS core driver"
+	depends on SSB && MIPS
+	select SSB_SERIAL
+	help
+	  Driver for the Sonics Silicon Backplane attached
+	  Broadcom MIPS core.
+
+	  If unsure, say N
+
+config SSB_DRIVER_EXTIF
+	bool "SSB Broadcom EXTIF core driver"
+	depends on SSB_DRIVER_MIPS
+	help
+	  Driver for the Sonics Silicon Backplane attached
+	  Broadcom EXTIF core.
+
+	  If unsure, say N
+
+endmenu
diff --git a/drivers/ssb/driver_chipcommon.c b/drivers/ssb/driver_chipcommon.c
new file mode 100644
index 0000000..8e5491c
--- /dev/null
+++ b/drivers/ssb/driver_chipcommon.c
@@ -0,0 +1,394 @@
+/*
+ * Sonics Silicon Backplane
+ * Broadcom ChipCommon core driver
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, 2007, Michael Buesch <[email protected]>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/ssb/ssb.h>
+#include <linux/ssb/ssb_regs.h>
+#include <linux/pci.h>
+
+#include "ssb_private.h"
+
+
+/* Clock sources */
+enum ssb_clksrc {
+	/* PCI clock */
+	SSB_CHIPCO_CLKSRC_PCI,
+	/* Crystal slow clock oscillator */
+	SSB_CHIPCO_CLKSRC_XTALOS,
+	/* Low power oscillator */
+	SSB_CHIPCO_CLKSRC_LOPWROS,
+};
+
+
+static inline u32 chipco_read32(struct ssb_chipcommon *cc,
+				u16 offset)
+{
+	return ssb_read32(cc->dev, offset);
+}
+
+static inline void chipco_write32(struct ssb_chipcommon *cc,
+				  u16 offset,
+				  u32 value)
+{
+	ssb_write32(cc->dev, offset, value);
+}
+
+void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
+			      enum ssb_clkmode mode)
+{
+	struct ssb_device *ccdev = cc->dev;
+	struct ssb_bus *bus;
+	u32 tmp;
+
+	if (!ccdev)
+		return;
+	bus = ccdev->bus;
+	/* chipcommon cores prior to rev6 don't support dynamic clock control */
+	if (ccdev->id.revision < 6)
+		return;
+	/* chipcommon cores rev10 are a whole new ball game */
+	if (ccdev->id.revision >= 10)
+		return;
+	if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
+		return;
+
+	switch (mode) {
+	case SSB_CLKMODE_SLOW:
+		tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
+		tmp |= SSB_CHIPCO_SLOWCLKCTL_FSLOW;
+		chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
+		break;
+	case SSB_CLKMODE_FAST:
+		ssb_pci_xtal(bus, SSB_GPIO_XTAL, 1); /* Force crystal on */
+		tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
+		tmp &= ~SSB_CHIPCO_SLOWCLKCTL_FSLOW;
+		tmp |= SSB_CHIPCO_SLOWCLKCTL_IPLL;
+		chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
+		break;
+	case SSB_CLKMODE_DYNAMIC:
+		tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
+		tmp &= ~SSB_CHIPCO_SLOWCLKCTL_FSLOW;
+		tmp &= ~SSB_CHIPCO_SLOWCLKCTL_IPLL;
+		tmp &= ~SSB_CHIPCO_SLOWCLKCTL_ENXTAL;
+		if ((tmp & SSB_CHIPCO_SLOWCLKCTL_SRC) != SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL)
+			tmp |= SSB_CHIPCO_SLOWCLKCTL_ENXTAL;
+		chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
+
+		/* for dynamic control, we have to release our xtal_pu "force on" */
+		if (tmp & SSB_CHIPCO_SLOWCLKCTL_ENXTAL)
+			ssb_pci_xtal(bus, SSB_GPIO_XTAL, 0);
+		break;
+	default:
+		SSB_WARN_ON(1);
+	}
+}
+
+/* Get the Slow Clock Source */
+static enum ssb_clksrc chipco_pctl_get_slowclksrc(struct ssb_chipcommon *cc)
+{
+	struct ssb_bus *bus = cc->dev->bus;
+	u32 uninitialized_var(tmp);
+
+	if (cc->dev->id.revision < 6) {
+		if (bus->bustype == SSB_BUSTYPE_SSB ||
+		    bus->bustype == SSB_BUSTYPE_PCMCIA)
+			return SSB_CHIPCO_CLKSRC_XTALOS;
+		if (bus->bustype == SSB_BUSTYPE_PCI) {
+			pci_read_config_dword(bus->host_pci, SSB_GPIO_OUT, &tmp);
+			if (tmp & 0x10)
+				return SSB_CHIPCO_CLKSRC_PCI;
+			return SSB_CHIPCO_CLKSRC_XTALOS;
+		}
+	}
+	if (cc->dev->id.revision < 10) {
+		tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
+		tmp &= 0x7;
+		if (tmp == 0)
+			return SSB_CHIPCO_CLKSRC_LOPWROS;
+		if (tmp == 1)
+			return SSB_CHIPCO_CLKSRC_XTALOS;
+		if (tmp == 2)
+			return SSB_CHIPCO_CLKSRC_PCI;
+	}
+
+	return SSB_CHIPCO_CLKSRC_XTALOS;
+}
+
+/* Get maximum or minimum (depending on get_max flag) slowclock frequency. */
+static int chipco_pctl_clockfreqlimit(struct ssb_chipcommon *cc, int get_max)
+{
+	int uninitialized_var(limit);
+	enum ssb_clksrc clocksrc;
+	int divisor = 1;
+	u32 tmp;
+
+	clocksrc = chipco_pctl_get_slowclksrc(cc);
+	if (cc->dev->id.revision < 6) {
+		switch (clocksrc) {
+		case SSB_CHIPCO_CLKSRC_PCI:
+			divisor = 64;
+			break;
+		case SSB_CHIPCO_CLKSRC_XTALOS:
+			divisor = 32;
+			break;
+		default:
+			SSB_WARN_ON(1);
+		}
+	} else if (cc->dev->id.revision < 10) {
+		switch (clocksrc) {
+		case SSB_CHIPCO_CLKSRC_LOPWROS:
+			break;
+		case SSB_CHIPCO_CLKSRC_XTALOS:
+		case SSB_CHIPCO_CLKSRC_PCI:
+			tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
+			divisor = (tmp >> 16) + 1;
+			divisor *= 4;
+			break;
+		}
+	} else {
+		tmp = chipco_read32(cc, SSB_CHIPCO_SYSCLKCTL);
+		divisor = (tmp >> 16) + 1;
+		divisor *= 4;
+	}
+
+	switch (clocksrc) {
+	case SSB_CHIPCO_CLKSRC_LOPWROS:
+		if (get_max)
+			limit = 43000;
+		else
+			limit = 25000;
+		break;
+	case SSB_CHIPCO_CLKSRC_XTALOS:
+		if (get_max)
+			limit = 20200000;
+		else
+			limit = 19800000;
+		break;
+	case SSB_CHIPCO_CLKSRC_PCI:
+		if (get_max)
+			limit = 34000000;
+		else
+			limit = 25000000;
+		break;
+	}
+	limit /= divisor;
+
+	return limit;
+}
+
+static void chipco_powercontrol_init(struct ssb_chipcommon *cc)
+{
+	struct ssb_bus *bus = cc->dev->bus;
+
+	if (bus->chip_id == 0x4321) {
+		if (bus->chip_rev == 0)
+			chipco_write32(cc, SSB_CHIPCO_CHIPCTL, 0x3A4);
+		else if (bus->chip_rev == 1)
+			chipco_write32(cc, SSB_CHIPCO_CHIPCTL, 0xA4);
+	}
+
+	if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
+		return;
+
+	if (cc->dev->id.revision >= 10) {
+		/* Set Idle Power clock rate to 1Mhz */
+		chipco_write32(cc, SSB_CHIPCO_SYSCLKCTL,
+			       (chipco_read32(cc, SSB_CHIPCO_SYSCLKCTL) &
+				0x0000FFFF) | 0x00040000);
+	} else {
+		int maxfreq;
+
+		maxfreq = chipco_pctl_clockfreqlimit(cc, 1);
+		chipco_write32(cc, SSB_CHIPCO_PLLONDELAY,
+			       (maxfreq * 150 + 999999) / 1000000);
+		chipco_write32(cc, SSB_CHIPCO_FREFSELDELAY,
+			       (maxfreq * 15 + 999999) / 1000000);
+	}
+}
+
+static void calc_fast_powerup_delay(struct ssb_chipcommon *cc)
+{
+	struct ssb_bus *bus = cc->dev->bus;
+	int minfreq;
+	unsigned int tmp;
+	u32 pll_on_delay;
+
+	if (bus->bustype != SSB_BUSTYPE_PCI)
+		return;
+	if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
+		return;
+
+	minfreq = chipco_pctl_clockfreqlimit(cc, 0);
+	pll_on_delay = chipco_read32(cc, SSB_CHIPCO_PLLONDELAY);
+	tmp = (((pll_on_delay + 2) * 1000000) + (minfreq - 1)) / minfreq;
+	SSB_WARN_ON(tmp & ~0xFFFF);
+
+	cc->fast_pwrup_delay = tmp;
+}
+
+void ssb_chipcommon_init(struct ssb_chipcommon *cc)
+{
+	if (!cc->dev)
+		return; /* We don't have a ChipCommon */
+	chipco_powercontrol_init(cc);
+	ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
+	calc_fast_powerup_delay(cc);
+}
+
+void ssb_chipco_suspend(struct ssb_chipcommon *cc, pm_message_t state)
+{
+	if (!cc->dev)
+		return;
+	ssb_chipco_set_clockmode(cc, SSB_CLKMODE_SLOW);
+}
+
+void ssb_chipco_resume(struct ssb_chipcommon *cc)
+{
+	if (!cc->dev)
+		return;
+	chipco_powercontrol_init(cc);
+	ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
+}
+
+void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
+				 u32 *plltype, u32 *n, u32 *m)
+{
+	*n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N);
+	*plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
+	switch (*plltype) {
+	case SSB_PLLTYPE_6: /* 100/200 or 120/240 only */
+		*m = chipco_read32(cc, SSB_CHIPCO_CLOCK_MIPS);
+		break;
+	case SSB_PLLTYPE_3: /* 25Mhz, 2 dividers */
+		if (cc->dev->bus->chip_id != 0x5365) {
+			*m = chipco_read32(cc, SSB_CHIPCO_CLOCK_M2);
+			break;
+		}
+		/* Fallthough */
+	default:
+		*m = chipco_read32(cc, SSB_CHIPCO_CLOCK_SB);
+	}
+}
+
+void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
+			    unsigned long ns)
+{
+	struct ssb_device *dev = cc->dev;
+	struct ssb_bus *bus = dev->bus;
+	u32 tmp;
+
+	/* set register for external IO to control LED. */
+	chipco_write32(cc, SSB_CHIPCO_PROG_CFG, 0x11);
+	tmp = DIV_ROUND_UP(10, ns) << SSB_PROG_WCNT_3_SHIFT;		/* Waitcount-3 = 10ns */
+	tmp |= DIV_ROUND_UP(40, ns) << SSB_PROG_WCNT_1_SHIFT;	/* Waitcount-1 = 40ns */
+	tmp |= DIV_ROUND_UP(240, ns);				/* Waitcount-0 = 240ns */
+	chipco_write32(cc, SSB_CHIPCO_PROG_WAITCNT, tmp);	/* 0x01020a0c for a 100Mhz clock */
+
+	/* Set timing for the flash */
+	tmp = DIV_ROUND_UP(10, ns) << SSB_FLASH_WCNT_3_SHIFT;	/* Waitcount-3 = 10nS */
+	tmp |= DIV_ROUND_UP(10, ns) << SSB_FLASH_WCNT_1_SHIFT;	/* Waitcount-1 = 10nS */
+	tmp |= DIV_ROUND_UP(120, ns);				/* Waitcount-0 = 120nS */
+	if ((bus->chip_id == 0x5365) ||
+	    (dev->id.revision < 9))
+		chipco_write32(cc, SSB_CHIPCO_FLASH_WAITCNT, tmp);
+	if ((bus->chip_id == 0x5365) ||
+	    (dev->id.revision < 9) ||
+	    ((bus->chip_id == 0x5350) && (bus->chip_rev == 0)))
+		chipco_write32(cc, SSB_CHIPCO_PCMCIA_MEMWAIT, tmp);
+
+	if (bus->chip_id == 0x5350) {
+		/* Enable EXTIF */
+		tmp = DIV_ROUND_UP(10, ns) << SSB_PROG_WCNT_3_SHIFT;	  /* Waitcount-3 = 10ns */
+		tmp |= DIV_ROUND_UP(20, ns) << SSB_PROG_WCNT_2_SHIFT;  /* Waitcount-2 = 20ns */
+		tmp |= DIV_ROUND_UP(100, ns) << SSB_PROG_WCNT_1_SHIFT; /* Waitcount-1 = 100ns */
+		tmp |= DIV_ROUND_UP(120, ns);			  /* Waitcount-0 = 120ns */
+		chipco_write32(cc, SSB_CHIPCO_PROG_WAITCNT, tmp); /* 0x01020a0c for a 100Mhz clock */
+	}
+}
+
+
+#ifdef CONFIG_SSB_SERIAL
+int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
+			   struct ssb_serial_port *ports)
+{
+	struct ssb_bus *bus = cc->dev->bus;
+	int nr_ports = 0;
+	u32 plltype;
+	unsigned int irq;
+	u32 baud_base, div;
+	u32 i, n;
+
+	plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
+	irq = ssb_mips_irq(cc->dev);
+
+	if (plltype == SSB_PLLTYPE_1) {
+		/* PLL clock */
+		baud_base = ssb_calc_clock_rate(plltype,
+						chipco_read32(cc, SSB_CHIPCO_CLOCK_N),
+						chipco_read32(cc, SSB_CHIPCO_CLOCK_M2));
+		div = 1;
+	} else {
+		if (cc->dev->id.revision >= 11) {
+			/* Fixed ALP clock */
+			baud_base = 20000000;
+			div = 1;
+			/* Set the override bit so we don't divide it */
+			chipco_write32(cc, SSB_CHIPCO_CORECTL,
+				       SSB_CHIPCO_CORECTL_UARTCLK0);
+		} else if (cc->dev->id.revision >= 3) {
+			/* Internal backplane clock */
+			baud_base = ssb_clockspeed(bus);
+			div = 2; /* Minimum divisor */
+			chipco_write32(cc, SSB_CHIPCO_CLKDIV,
+				       (chipco_read32(cc, SSB_CHIPCO_CLKDIV)
+					& ~SSB_CHIPCO_CLKDIV_UART) | div);
+		} else {
+			/* Fixed internal backplane clock */
+			baud_base = 88000000;
+			div = 48;
+		}
+
+		/* Clock source depends on strapping if UartClkOverride is unset */
+		if ((cc->dev->id.revision > 0) &&
+		    !(chipco_read32(cc, SSB_CHIPCO_CORECTL) & SSB_CHIPCO_CORECTL_UARTCLK0)) {
+			if ((cc->capabilities & SSB_CHIPCO_CAP_UARTCLK) ==
+			    SSB_CHIPCO_CAP_UARTCLK_INT) {
+				/* Internal divided backplane clock */
+				baud_base /= div;
+			} else {
+				/* Assume external clock of 1.8432 MHz */
+				baud_base = 1843200;
+			}
+		}
+	}
+
+	/* Determine the registers of the UARTs */
+	n = (cc->capabilities & SSB_CHIPCO_CAP_NRUART);
+	for (i = 0; i < n; i++) {
+		void __iomem *cc_mmio;
+		void __iomem *uart_regs;
+
+		cc_mmio = cc->dev->bus->mmio + (cc->dev->core_index * SSB_CORE_SIZE);
+		uart_regs = cc_mmio + SSB_CHIPCO_UART0_DATA;
+		/* Offset changed at after rev 0 */
+		if (cc->dev->id.revision == 0)
+			uart_regs += (i * 8);
+		else
+			uart_regs += (i * 256);
+
+		nr_ports++;
+		ports[i].regs = uart_regs;
+		ports[i].irq = irq;
+		ports[i].baud_base = baud_base;
+		ports[i].reg_shift = 0;
+	}
+
+	return nr_ports;
+}
+#endif /* CONFIG_SSB_SERIAL */
diff --git a/drivers/ssb/driver_mipscore.c b/drivers/ssb/driver_mipscore.c
new file mode 100644
index 0000000..3f09598
--- /dev/null
+++ b/drivers/ssb/driver_mipscore.c
@@ -0,0 +1,258 @@
+/*
+ * Sonics Silicon Backplane
+ * Broadcom MIPS core driver
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, 2007, Michael Buesch <[email protected]>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/ssb/ssb.h>
+
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <linux/time.h>
+
+#include "ssb_private.h"
+
+
+static inline u32 mips_read32(struct ssb_mipscore *mcore,
+			      u16 offset)
+{
+	return ssb_read32(mcore->dev, offset);
+}
+
+static inline void mips_write32(struct ssb_mipscore *mcore,
+				u16 offset,
+				u32 value)
+{
+	ssb_write32(mcore->dev, offset, value);
+}
+
+static const u32 ipsflag_irq_mask[] = {
+	0,
+	SSB_IPSFLAG_IRQ1,
+	SSB_IPSFLAG_IRQ2,
+	SSB_IPSFLAG_IRQ3,
+	SSB_IPSFLAG_IRQ4,
+};
+
+static const u32 ipsflag_irq_shift[] = {
+	0,
+	SSB_IPSFLAG_IRQ1_SHIFT,
+	SSB_IPSFLAG_IRQ2_SHIFT,
+	SSB_IPSFLAG_IRQ3_SHIFT,
+	SSB_IPSFLAG_IRQ4_SHIFT,
+};
+
+static inline u32 ssb_irqflag(struct ssb_device *dev)
+{
+	return ssb_read32(dev, SSB_TPSFLAG) & SSB_TPSFLAG_BPFLAG;
+}
+
+/* Get the MIPS IRQ assignment for a specified device.
+ * If unassigned, 0 is returned.
+ */
+unsigned int ssb_mips_irq(struct ssb_device *dev)
+{
+	struct ssb_bus *bus = dev->bus;
+	u32 irqflag;
+	u32 ipsflag;
+	u32 tmp;
+	unsigned int irq;
+
+	irqflag = ssb_irqflag(dev);
+	ipsflag = ssb_read32(bus->mipscore.dev, SSB_IPSFLAG);
+	for (irq = 1; irq <= 4; irq++) {
+		tmp = ((ipsflag & ipsflag_irq_mask[irq]) >> ipsflag_irq_shift[irq]);
+		if (tmp == irqflag)
+			break;
+	}
+	if (irq	== 5)
+		irq = 0;
+
+	return irq;
+}
+
+static void clear_irq(struct ssb_bus *bus, unsigned int irq)
+{
+	struct ssb_device *dev = bus->mipscore.dev;
+
+	/* Clear the IRQ in the MIPScore backplane registers */
+	if (irq == 0) {
+		ssb_write32(dev, SSB_INTVEC, 0);
+	} else {
+		ssb_write32(dev, SSB_IPSFLAG,
+			    ssb_read32(dev, SSB_IPSFLAG) |
+			    ipsflag_irq_mask[irq]);
+	}
+}
+
+static void set_irq(struct ssb_device *dev, unsigned int irq)
+{
+	unsigned int oldirq = ssb_mips_irq(dev);
+	struct ssb_bus *bus = dev->bus;
+	struct ssb_device *mdev = bus->mipscore.dev;
+	u32 irqflag = ssb_irqflag(dev);
+
+	dev->irq = irq + 2;
+
+	ssb_dprintk(KERN_INFO PFX
+		    "set_irq: core 0x%04x, irq %d => %d\n",
+		    dev->id.coreid, oldirq, irq);
+	/* clear the old irq */
+	if (oldirq == 0)
+		ssb_write32(mdev, SSB_INTVEC, (~(1 << irqflag) & ssb_read32(mdev, SSB_INTVEC)));
+	else
+		clear_irq(bus, oldirq);
+
+	/* assign the new one */
+	if (irq == 0)
+		ssb_write32(mdev, SSB_INTVEC, ((1 << irqflag) & ssb_read32(mdev, SSB_INTVEC)));
+
+	irqflag <<= ipsflag_irq_shift[irq];
+	irqflag |= (ssb_read32(mdev, SSB_IPSFLAG) & ~ipsflag_irq_mask[irq]);
+	ssb_write32(mdev, SSB_IPSFLAG, irqflag);
+}
+
+/* XXX: leave here or move into separate extif driver? */
+static int ssb_extif_serial_init(struct ssb_device *dev, struct ssb_serial_ports *ports)
+{
+
+}
+
+
+static void ssb_mips_serial_init(struct ssb_mipscore *mcore)
+{
+	struct ssb_bus *bus = mcore->dev->bus;
+
+	//TODO if (EXTIF available
+#if 0
+		extifregs_t *eir = (extifregs_t *) regs;
+		sbconfig_t *sb;
+
+		/* Determine external UART register base */
+		sb = (sbconfig_t *)((ulong) eir + SBCONFIGOFF);
+		base = EXTIF_CFGIF_BASE(sb_base(R_REG(&sb->sbadmatch1)));
+
+		/* Determine IRQ */
+		irq = sb_irq(sbh);
+
+		/* Disable GPIO interrupt initially */
+		W_REG(&eir->gpiointpolarity, 0);
+		W_REG(&eir->gpiointmask, 0);
+
+		/* Search for external UARTs */
+		n = 2;
+		for (i = 0; i < 2; i++) {
+			regs = (void *) REG_MAP(base + (i * 8), 8);
+			if (BCMINIT(serial_exists)(regs)) {
+				/* Set GPIO 1 to be the external UART IRQ */
+				W_REG(&eir->gpiointmask, 2);
+				if (add)
+					add(regs, irq, 13500000, 0);
+			}
+		}
+
+		/* Add internal UART if enabled */
+		if (R_REG(&eir->corecontrol) & CC_UE)
+			if (add)
+				add((void *) &eir->uartdata, irq, sb_clock(sbh), 2);
+
+#endif
+	if (bus->extif.dev)
+		mcore->nr_serial_ports = ssb_extif_serial_init(&bus->extif, mcore->serial_ports);
+	else if (bus->chipco.dev)
+		mcore->nr_serial_ports = ssb_chipco_serial_init(&bus->chipco, mcore->serial_ports);
+	else
+		mcore->nr_serial_ports = 0;
+}
+
+static void ssb_mips_flash_detect(struct ssb_mipscore *mcore)
+{
+	struct ssb_bus *bus = mcore->dev->bus;
+
+	if (bus->chipco.dev) {
+		mcore->flash_window = 0x1c000000;
+		mcore->flash_window_size = 0x800000;
+	} else {
+		mcore->flash_window = 0x1fc00000;
+		mcore->flash_window_size = 0x400000;
+	}
+}
+
+
+static void ssb_cpu_clock(struct ssb_mipscore *mcore)
+{
+}
+
+void ssb_mipscore_init(struct ssb_mipscore *mcore)
+{
+	struct ssb_bus *bus = mcore->dev->bus;
+	struct ssb_device *dev;
+	unsigned long hz, ns;
+	unsigned int irq, i;
+
+	if (!mcore->dev)
+		return; /* We don't have a MIPS core */
+
+	ssb_dprintk(KERN_INFO PFX "Initializing MIPS core...\n");
+
+	hz = ssb_clockspeed(bus);
+	if (!hz)
+		hz = 100000000;
+	ns = 1000000000 / hz;
+
+//TODO
+#if 0
+	if (have EXTIF) {
+		/* Initialize extif so we can get to the LEDs and external UART */
+		W_REG(&eir->prog_config, CF_EN);
+
+		/* Set timing for the flash */
+		tmp = CEIL(10, ns) << FW_W3_SHIFT;	/* W3 = 10nS */
+		tmp = tmp | (CEIL(40, ns) << FW_W1_SHIFT); /* W1 = 40nS */
+		tmp = tmp | CEIL(120, ns);		/* W0 = 120nS */
+		W_REG(&eir->prog_waitcount, tmp);	/* 0x01020a0c for a 100Mhz clock */
+
+		/* Set programmable interface timing for external uart */
+		tmp = CEIL(10, ns) << FW_W3_SHIFT;	/* W3 = 10nS */
+		tmp = tmp | (CEIL(20, ns) << FW_W2_SHIFT); /* W2 = 20nS */
+		tmp = tmp | (CEIL(100, ns) << FW_W1_SHIFT); /* W1 = 100nS */
+		tmp = tmp | CEIL(120, ns);		/* W0 = 120nS */
+		W_REG(&eir->prog_waitcount, tmp);
+	}
+#endif
+	if (bus->chipco.dev)
+		ssb_chipco_timing_init(&bus->chipco, ns);
+
+	/* Assign IRQs to all cores on the bus, start with irq line 2, because serial usually takes 1 */
+	for (irq = 2, i = 0; i < bus->nr_devices; i++) {
+		dev = &(bus->devices[i]);
+		dev->irq = ssb_mips_irq(dev) + 2;
+		switch (dev->id.coreid) {
+		case SSB_DEV_USB11_HOST:
+			/* shouldn't need a separate irq line for non-4710, most of them have a proper
+			 * external usb controller on the pci */
+			if ((bus->chip_id == 0x4710) && (irq <= 4)) {
+				set_irq(dev, irq++);
+				break;
+			}
+			/* fallthrough */
+		case SSB_DEV_PCI:
+		case SSB_DEV_ETHERNET:
+		case SSB_DEV_80211:
+		case SSB_DEV_USB20_HOST:
+			/* These devices get their own IRQ line if available, the rest goes on IRQ0 */
+			if (irq <= 4) {
+				set_irq(dev, irq++);
+				break;
+			}
+		}
+	}
+
+	ssb_mips_serial_init(mcore);
+	ssb_mips_flash_detect(mcore);
+}
diff --git a/drivers/ssb/driver_pcicore.c b/drivers/ssb/driver_pcicore.c
new file mode 100644
index 0000000..e11b103
--- /dev/null
+++ b/drivers/ssb/driver_pcicore.c
@@ -0,0 +1,568 @@
+/*
+ * Sonics Silicon Backplane
+ * Broadcom PCI-core driver
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, 2007, Michael Buesch <[email protected]>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/ssb/ssb.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+
+#include "ssb_private.h"
+
+
+static inline
+u32 pcicore_read32(struct ssb_pcicore *pc, u16 offset)
+{
+	return ssb_read32(pc->dev, offset);
+}
+
+static inline
+void pcicore_write32(struct ssb_pcicore *pc, u16 offset, u32 value)
+{
+	ssb_write32(pc->dev, offset, value);
+}
+
+/**************************************************
+ * Code for hostmode operation.
+ **************************************************/
+
+#ifdef CONFIG_SSB_PCICORE_HOSTMODE
+
+#include <asm/paccess.h>
+/* Probe a 32bit value on the bus and catch bus exceptions.
+ * Returns nonzero on a bus exception.
+ * This is MIPS specific */
+#define mips_busprobe32(val, addr)	get_dbe((val), ((u32 *)(addr)))
+
+/* Assume one-hot slot wiring */
+#define SSB_PCI_SLOT_MAX	16
+
+/* Global lock is OK, as we won't have more than one extpci anyway. */
+static DEFINE_SPINLOCK(cfgspace_lock);
+/* Core to access the external PCI config space. Can only have one. */
+static struct ssb_pcicore *extpci_core;
+
+static u32 ssb_pcicore_pcibus_iobase = 0x100;
+static u32 ssb_pcicore_pcibus_membase = SSB_PCI_DMA;
+
+int pcibios_plat_dev_init(struct pci_dev *d)
+{
+	struct resource *res;
+	int pos, size;
+	u32 *base;
+
+	ssb_printk(KERN_INFO "PCI: Fixing up device %s\n",
+		   pci_name(d));
+
+	/* Fix up resource bases */
+	for (pos = 0; pos < 6; pos++) {
+		res = &d->resource[pos];
+		if (res->flags & IORESOURCE_IO)
+			base = &ssb_pcicore_pcibus_iobase;
+		else
+			base = &ssb_pcicore_pcibus_membase;
+		if (res->end) {
+			size = res->end - res->start + 1;
+			if (*base & (size - 1))
+				*base = (*base + size) & ~(size - 1);
+			res->start = *base;
+			res->end = res->start + size - 1;
+			*base += size;
+			pci_write_config_dword(d, PCI_BASE_ADDRESS_0 + (pos << 2), res->start);
+		}
+		/* Fix up PCI bridge BAR0 only */
+		if (d->bus->number == 0 && PCI_SLOT(d->devfn) == 0)
+			break;
+	}
+	/* Fix up interrupt lines */
+	d->irq = ssb_mips_irq(extpci_core->dev) + 2;
+	pci_write_config_byte(d, PCI_INTERRUPT_LINE, d->irq);
+
+	return 0;
+}
+
+static void __init ssb_fixup_pcibridge(struct pci_dev *dev)
+{
+	if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) != 0)
+		return;
+
+	ssb_printk(KERN_INFO "PCI: fixing up bridge\n");
+
+	/* Enable PCI bridge bus mastering and memory space */
+	pci_set_master(dev);
+	pcibios_enable_device(dev, ~0);
+
+	/* Enable PCI bridge BAR1 prefetch and burst */
+	pci_write_config_dword(dev, SSB_BAR1_CONTROL, 3);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_ANY_ID, PCI_ANY_ID, ssb_fixup_pcibridge);
+
+int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return ssb_mips_irq(extpci_core->dev) + 2;
+}
+
+static u32 get_cfgspace_addr(struct ssb_pcicore *pc,
+			     unsigned int bus, unsigned int dev,
+			     unsigned int func, unsigned int off)
+{
+	u32 addr = 0;
+	u32 tmp;
+
+	if (unlikely(pc->cardbusmode && dev > 1))
+		goto out;
+	if (bus == 0) {
+		/* Type 0 transaction */
+		if (unlikely(dev >= SSB_PCI_SLOT_MAX))
+			goto out;
+		/* Slide the window */
+		tmp = SSB_PCICORE_SBTOPCI_CFG0;
+		tmp |= ((1 << (dev + 16)) & SSB_PCICORE_SBTOPCI1_MASK);
+		pcicore_write32(pc, SSB_PCICORE_SBTOPCI1, tmp);
+		/* Calculate the address */
+		addr = SSB_PCI_CFG;
+		addr |= ((1 << (dev + 16)) & ~SSB_PCICORE_SBTOPCI1_MASK);
+		addr |= (func << 8);
+		addr |= (off & ~3);
+	} else {
+		/* Type 1 transaction */
+		pcicore_write32(pc, SSB_PCICORE_SBTOPCI1,
+				SSB_PCICORE_SBTOPCI_CFG1);
+		/* Calculate the address */
+		addr = SSB_PCI_CFG;
+		addr |= (bus << 16);
+		addr |= (dev << 11);
+		addr |= (func << 8);
+		addr |= (off & ~3);
+	}
+out:
+	return addr;
+}
+
+static int ssb_extpci_read_config(struct ssb_pcicore *pc,
+				  unsigned int bus, unsigned int dev,
+				  unsigned int func, unsigned int off,
+				  void *buf, int len)
+{
+	int err = -EINVAL;
+	u32 addr, val;
+	void __iomem *mmio;
+
+	SSB_WARN_ON(!pc->hostmode);
+	if (unlikely(len != 1 && len != 2 && len != 4))
+		goto out;
+	addr = get_cfgspace_addr(pc, bus, dev, func, off);
+	if (unlikely(!addr))
+		goto out;
+	err = -ENOMEM;
+	mmio = ioremap_nocache(addr, len);
+	if (!mmio)
+		goto out;
+
+	if (mips_busprobe32(val, mmio)) {
+		val = 0xffffffff;
+		goto unmap;
+	}
+
+	val = readl(mmio);
+	val >>= (8 * (off & 3));
+
+	switch (len) {
+	case 1:
+		*((u8 *)buf) = (u8)val;
+		break;
+	case 2:
+		*((u16 *)buf) = (u16)val;
+		break;
+	case 4:
+		*((u32 *)buf) = (u32)val;
+		break;
+	}
+	err = 0;
+unmap:
+	iounmap(mmio);
+out:
+	return err;
+}
+
+static int ssb_extpci_write_config(struct ssb_pcicore *pc,
+				   unsigned int bus, unsigned int dev,
+				   unsigned int func, unsigned int off,
+				   const void *buf, int len)
+{
+	int err = -EINVAL;
+	u32 addr, val = 0;
+	void __iomem *mmio;
+
+	SSB_WARN_ON(!pc->hostmode);
+	if (unlikely(len != 1 && len != 2 && len != 4))
+		goto out;
+	addr = get_cfgspace_addr(pc, bus, dev, func, off);
+	if (unlikely(!addr))
+		goto out;
+	err = -ENOMEM;
+	mmio = ioremap_nocache(addr, len);
+	if (!mmio)
+		goto out;
+
+	if (mips_busprobe32(val, mmio)) {
+		val = 0xffffffff;
+		goto unmap;
+	}
+
+	switch (len) {
+	case 1:
+		val = readl(mmio);
+		val &= ~(0xFF << (8 * (off & 3)));
+		val |= *((const u8 *)buf) << (8 * (off & 3));
+		break;
+	case 2:
+		val = readl(mmio);
+		val &= ~(0xFFFF << (8 * (off & 3)));
+		val |= *((const u16 *)buf) << (8 * (off & 3));
+		break;
+	case 4:
+		val = *((const u32 *)buf);
+		break;
+	}
+	writel(*((const u32 *)buf), mmio);
+
+	err = 0;
+unmap:
+	iounmap(mmio);
+out:
+	return err;
+}
+
+static int ssb_pcicore_read_config(struct pci_bus *bus, unsigned int devfn,
+				   int reg, int size, u32 *val)
+{
+	unsigned long flags;
+	int err;
+
+	spin_lock_irqsave(&cfgspace_lock, flags);
+	err = ssb_extpci_read_config(extpci_core, bus->number, PCI_SLOT(devfn),
+				     PCI_FUNC(devfn), reg, val, size);
+	spin_unlock_irqrestore(&cfgspace_lock, flags);
+
+	return err ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL;
+}
+
+static int ssb_pcicore_write_config(struct pci_bus *bus, unsigned int devfn,
+				    int reg, int size, u32 val)
+{
+	unsigned long flags;
+	int err;
+
+	spin_lock_irqsave(&cfgspace_lock, flags);
+	err = ssb_extpci_write_config(extpci_core, bus->number, PCI_SLOT(devfn),
+				      PCI_FUNC(devfn), reg, &val, size);
+	spin_unlock_irqrestore(&cfgspace_lock, flags);
+
+	return err ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL;
+}
+
+static struct pci_ops ssb_pcicore_pciops = {
+	.read	= ssb_pcicore_read_config,
+	.write	= ssb_pcicore_write_config,
+};
+
+static struct resource ssb_pcicore_mem_resource = {
+	.name	= "SSB PCIcore external memory",
+	.start	= SSB_PCI_DMA,
+	.end	= SSB_PCI_DMA + SSB_PCI_DMA_SZ - 1,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource ssb_pcicore_io_resource = {
+	.name	= "SSB PCIcore external I/O",
+	.start	= 0x100,
+	.end	= 0x7FF,
+	.flags	= IORESOURCE_IO,
+};
+
+static struct pci_controller ssb_pcicore_controller = {
+	.pci_ops	= &ssb_pcicore_pciops,
+	.io_resource	= &ssb_pcicore_io_resource,
+	.mem_resource	= &ssb_pcicore_mem_resource,
+	.mem_offset	= 0x24000000,
+};
+
+static void ssb_pcicore_init_hostmode(struct ssb_pcicore *pc)
+{
+	u32 val;
+
+	if (WARN_ON(extpci_core))
+		return;
+	extpci_core = pc;
+
+	ssb_dprintk(KERN_INFO PFX "PCIcore in host mode found\n");
+	/* Reset devices on the external PCI bus */
+	val = SSB_PCICORE_CTL_RST_OE;
+	val |= SSB_PCICORE_CTL_CLK_OE;
+	pcicore_write32(pc, SSB_PCICORE_CTL, val);
+	val |= SSB_PCICORE_CTL_CLK; /* Clock on */
+	pcicore_write32(pc, SSB_PCICORE_CTL, val);
+	udelay(150); /* Assertion time demanded by the PCI standard */
+	val |= SSB_PCICORE_CTL_RST; /* Deassert RST# */
+	pcicore_write32(pc, SSB_PCICORE_CTL, val);
+	udelay(1); /* Assertion time demanded by the PCI standard */
+
+	/*TODO cardbus mode */
+
+	/* 64MB I/O window */
+	pcicore_write32(pc, SSB_PCICORE_SBTOPCI0,
+			SSB_PCICORE_SBTOPCI_IO);
+	/* 64MB config space */
+	pcicore_write32(pc, SSB_PCICORE_SBTOPCI1,
+			SSB_PCICORE_SBTOPCI_CFG0);
+	/* 1GB memory window */
+	pcicore_write32(pc, SSB_PCICORE_SBTOPCI2,
+			SSB_PCICORE_SBTOPCI_MEM | SSB_PCI_DMA);
+
+	/* Enable PCI bridge BAR0 prefetch and burst */
+	val = PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+	ssb_extpci_write_config(pc, 0, 0, 0, PCI_COMMAND, &val, 2);
+	/* Clear error conditions */
+	val = 0;
+	ssb_extpci_write_config(pc, 0, 0, 0, PCI_STATUS, &val, 2);
+
+	/* Enable PCI interrupts */
+	pcicore_write32(pc, SSB_PCICORE_IMASK,
+			SSB_PCICORE_IMASK_INTA);
+
+	/* Ok, ready to run, register it to the system.
+	 * The following needs change, if we want to port hostmode
+	 * to non-MIPS platform. */
+	set_io_port_base((unsigned long)ioremap_nocache(SSB_PCI_MEM, 0x04000000));
+	register_pci_controller(&ssb_pcicore_controller);
+}
+
+static int pcicore_is_in_hostmode(struct ssb_pcicore *pc)
+{
+	struct ssb_bus *bus = pc->dev->bus;
+	u16 chipid_top;
+	u32 tmp;
+
+	chipid_top = (bus->chip_id & 0xFF00);
+	if (chipid_top != 0x4700 &&
+	    chipid_top != 0x5300)
+		return 0;
+
+	if (bus->sprom.r1.boardflags_lo & SSB_PCICORE_BFL_NOPCI)
+		return 0;
+
+	/* The 200-pin BCM4712 package does not bond out PCI. Even when
+	 * PCI is bonded out, some boards may leave the pins floating. */
+	if (bus->chip_id == 0x4712) {
+		if (bus->chip_package == SSB_CHIPPACK_BCM4712S)
+			return 0;
+		if (bus->chip_package == SSB_CHIPPACK_BCM4712M)
+			return 0;
+	}
+	if (bus->chip_id == 0x5350)
+		return 0;
+
+	return !mips_busprobe32(tmp, (bus->mmio + (pc->dev->core_index * SSB_CORE_SIZE)));
+}
+#endif /* CONFIG_SSB_PCICORE_HOSTMODE */
+
+
+/**************************************************
+ * Generic and Clientmode operation code.
+ **************************************************/
+
+static void ssb_pcicore_init_clientmode(struct ssb_pcicore *pc)
+{
+	/* Disable PCI interrupts. */
+	ssb_write32(pc->dev, SSB_INTVEC, 0);
+}
+
+void ssb_pcicore_init(struct ssb_pcicore *pc)
+{
+	struct ssb_device *dev = pc->dev;
+	struct ssb_bus *bus;
+
+	if (!dev)
+		return;
+	bus = dev->bus;
+	if (!ssb_device_is_enabled(dev))
+		ssb_device_enable(dev, 0);
+
+#ifdef CONFIG_SSB_PCICORE_HOSTMODE
+	pc->hostmode = pcicore_is_in_hostmode(pc);
+	if (pc->hostmode)
+		ssb_pcicore_init_hostmode(pc);
+#endif /* CONFIG_SSB_PCICORE_HOSTMODE */
+	if (!pc->hostmode)
+		ssb_pcicore_init_clientmode(pc);
+}
+
+static u32 ssb_pcie_read(struct ssb_pcicore *pc, u32 address)
+{
+	pcicore_write32(pc, 0x130, address);
+	return pcicore_read32(pc, 0x134);
+}
+
+static void ssb_pcie_write(struct ssb_pcicore *pc, u32 address, u32 data)
+{
+	pcicore_write32(pc, 0x130, address);
+	pcicore_write32(pc, 0x134, data);
+}
+
+static void ssb_pcie_mdio_write(struct ssb_pcicore *pc, u8 device,
+				u8 address, u16 data)
+{
+	const u16 mdio_control = 0x128;
+	const u16 mdio_data = 0x12C;
+	u32 v;
+	int i;
+
+	v = 0x80; /* Enable Preamble Sequence */
+	v |= 0x2; /* MDIO Clock Divisor */
+	pcicore_write32(pc, mdio_control, v);
+
+	v = (1 << 30); /* Start of Transaction */
+	v |= (1 << 28); /* Write Transaction */
+	v |= (1 << 17); /* Turnaround */
+	v |= (u32)device << 22;
+	v |= (u32)address << 18;
+	v |= data;
+	pcicore_write32(pc, mdio_data, v);
+	/* Wait for the device to complete the transaction */
+	udelay(10);
+	for (i = 0; i < 10; i++) {
+		v = pcicore_read32(pc, mdio_control);
+		if (v & 0x100 /* Trans complete */)
+			break;
+		msleep(1);
+	}
+	pcicore_write32(pc, mdio_control, 0);
+}
+
+static void ssb_broadcast_value(struct ssb_device *dev,
+				u32 address, u32 data)
+{
+	/* This is used for both, PCI and ChipCommon core, so be careful. */
+	BUILD_BUG_ON(SSB_PCICORE_BCAST_ADDR != SSB_CHIPCO_BCAST_ADDR);
+	BUILD_BUG_ON(SSB_PCICORE_BCAST_DATA != SSB_CHIPCO_BCAST_DATA);
+
+	ssb_write32(dev, SSB_PCICORE_BCAST_ADDR, address);
+	ssb_read32(dev, SSB_PCICORE_BCAST_ADDR); /* flush */
+	ssb_write32(dev, SSB_PCICORE_BCAST_DATA, data);
+	ssb_read32(dev, SSB_PCICORE_BCAST_DATA); /* flush */
+}
+
+static void ssb_commit_settings(struct ssb_bus *bus)
+{
+	struct ssb_device *dev;
+
+	dev = bus->chipco.dev ? bus->chipco.dev : bus->pcicore.dev;
+	if (WARN_ON(!dev))
+		return;
+	/* This forces an update of the cached registers. */
+	ssb_broadcast_value(dev, 0xFD8, 0);
+}
+
+int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc,
+				   struct ssb_device *dev)
+{
+	struct ssb_device *pdev = pc->dev;
+	struct ssb_bus *bus;
+	int err = 0;
+	u32 tmp;
+
+	might_sleep();
+
+	if (!pdev)
+		goto out;
+	bus = pdev->bus;
+
+	/* Enable interrupts for this device. */
+	if (bus->host_pci &&
+	    ((pdev->id.revision >= 6) || (pdev->id.coreid == SSB_DEV_PCIE))) {
+		u32 coremask;
+
+		/* Calculate the "coremask" for the device. */
+		coremask = (1 << dev->core_index);
+
+		err = pci_read_config_dword(bus->host_pci, SSB_PCI_IRQMASK, &tmp);
+		if (err)
+			goto out;
+		tmp |= coremask << 8;
+		err = pci_write_config_dword(bus->host_pci, SSB_PCI_IRQMASK, tmp);
+		if (err)
+			goto out;
+	} else {
+		u32 intvec;
+
+		intvec = ssb_read32(pdev, SSB_INTVEC);
+		if ((bus->chip_id & 0xFF00) == 0x4400) {
+			/* Workaround: On the BCM44XX the BPFLAG routing
+			 * bit is wrong. Use a hardcoded constant. */
+			intvec |= 0x00000002;
+		} else {
+			tmp = ssb_read32(dev, SSB_TPSFLAG);
+			tmp &= SSB_TPSFLAG_BPFLAG;
+			intvec |= tmp;
+		}
+		ssb_write32(pdev, SSB_INTVEC, intvec);
+	}
+
+	/* Setup PCIcore operation. */
+	if (pc->setup_done)
+		goto out;
+	if (pdev->id.coreid == SSB_DEV_PCI) {
+		tmp = pcicore_read32(pc, SSB_PCICORE_SBTOPCI2);
+		tmp |= SSB_PCICORE_SBTOPCI_PREF;
+		tmp |= SSB_PCICORE_SBTOPCI_BURST;
+		pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, tmp);
+
+		if (pdev->id.revision < 5) {
+			tmp = ssb_read32(pdev, SSB_IMCFGLO);
+			tmp &= ~SSB_IMCFGLO_SERTO;
+			tmp |= 2;
+			tmp &= ~SSB_IMCFGLO_REQTO;
+			tmp |= 3 << SSB_IMCFGLO_REQTO_SHIFT;
+			ssb_write32(pdev, SSB_IMCFGLO, tmp);
+			ssb_commit_settings(bus);
+		} else if (pdev->id.revision >= 11) {
+			tmp = pcicore_read32(pc, SSB_PCICORE_SBTOPCI2);
+			tmp |= SSB_PCICORE_SBTOPCI_MRM;
+			pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, tmp);
+		}
+	} else {
+		WARN_ON(pdev->id.coreid != SSB_DEV_PCIE);
+		//TODO: Better make defines for all these magic PCIE values.
+		if ((pdev->id.revision == 0) || (pdev->id.revision == 1)) {
+			/* TLP Workaround register. */
+			tmp = ssb_pcie_read(pc, 0x4);
+			tmp |= 0x8;
+			ssb_pcie_write(pc, 0x4, tmp);
+		}
+		if (pdev->id.revision == 0) {
+			const u8 serdes_rx_device = 0x1F;
+
+			ssb_pcie_mdio_write(pc, serdes_rx_device,
+					    2 /* Timer */, 0x8128);
+			ssb_pcie_mdio_write(pc, serdes_rx_device,
+					    6 /* CDR */, 0x0100);
+			ssb_pcie_mdio_write(pc, serdes_rx_device,
+					    7 /* CDR BW */, 0x1466);
+		} else if (pdev->id.revision == 1) {
+			/* DLLP Link Control register. */
+			tmp = ssb_pcie_read(pc, 0x100);
+			tmp |= 0x40;
+			ssb_pcie_write(pc, 0x100, tmp);
+		}
+	}
+	pc->setup_done = 1;
+out:
+	return err;
+}
+EXPORT_SYMBOL(ssb_pcicore_dev_irqvecs_enable);
diff --git a/drivers/ssb/main.c b/drivers/ssb/main.c
new file mode 100644
index 0000000..cfe090f
--- /dev/null
+++ b/drivers/ssb/main.c
@@ -0,0 +1,1112 @@
+/*
+ * Sonics Silicon Backplane
+ * Subsystem core
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, 2007, Michael Buesch <[email protected]>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "ssb_private.h"
+
+#include <linux/delay.h>
+#include <linux/ssb/ssb.h>
+#include <linux/ssb/ssb_regs.h>
+
+#include <linux/pci.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+
+
+MODULE_DESCRIPTION("Sonics Silicon Backplane driver");
+MODULE_LICENSE("GPL");
+
+
+/* Temporary list of yet-to-be-attached buses */
+static LIST_HEAD(attach_queue);
+/* List if running buses */
+static LIST_HEAD(buses);
+/* Software ID counter */
+static unsigned int next_busnumber;
+/* buses_mutes locks the two buslists and the next_busnumber.
+ * Don't lock this directly, but use ssb_buses_[un]lock() below. */
+static DEFINE_MUTEX(buses_mutex);
+
+/* There are differences in the codeflow, if the bus is
+ * initialized from early boot, as various needed services
+ * are not available early. This is a mechanism to delay
+ * these initializations to after early boot has finished.
+ * It's also used to avoid mutex locking, as that's not
+ * available and needed early. */
+static bool ssb_is_early_boot = 1;
+
+static void ssb_buses_lock(void);
+static void ssb_buses_unlock(void);
+
+
+#ifdef CONFIG_SSB_PCIHOST
+struct ssb_bus *ssb_pci_dev_to_bus(struct pci_dev *pdev)
+{
+	struct ssb_bus *bus;
+
+	ssb_buses_lock();
+	list_for_each_entry(bus, &buses, list) {
+		if (bus->bustype == SSB_BUSTYPE_PCI &&
+		    bus->host_pci == pdev)
+			goto found;
+	}
+	bus = NULL;
+found:
+	ssb_buses_unlock();
+
+	return bus;
+}
+#endif /* CONFIG_SSB_PCIHOST */
+
+static struct ssb_device *ssb_device_get(struct ssb_device *dev)
+{
+	if (dev)
+		get_device(dev->dev);
+	return dev;
+}
+
+static void ssb_device_put(struct ssb_device *dev)
+{
+	if (dev)
+		put_device(dev->dev);
+}
+
+static int ssb_bus_resume(struct ssb_bus *bus)
+{
+	int err;
+
+	ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 1);
+	err = ssb_pcmcia_init(bus);
+	if (err) {
+		/* No need to disable XTAL, as we don't have one on PCMCIA. */
+		return err;
+	}
+	ssb_chipco_resume(&bus->chipco);
+
+	return 0;
+}
+
+static int ssb_device_resume(struct device *dev)
+{
+	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_driver *ssb_drv;
+	struct ssb_bus *bus;
+	int err = 0;
+
+	bus = ssb_dev->bus;
+	if (bus->suspend_cnt == bus->nr_devices) {
+		err = ssb_bus_resume(bus);
+		if (err)
+			return err;
+	}
+	bus->suspend_cnt--;
+	if (dev->driver) {
+		ssb_drv = drv_to_ssb_drv(dev->driver);
+		if (ssb_drv && ssb_drv->resume)
+			err = ssb_drv->resume(ssb_dev);
+		if (err)
+			goto out;
+	}
+out:
+	return err;
+}
+
+static void ssb_bus_suspend(struct ssb_bus *bus, pm_message_t state)
+{
+	ssb_chipco_suspend(&bus->chipco, state);
+	ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 0);
+
+	/* Reset HW state information in memory, so that HW is
+	 * completely reinitialized on resume. */
+	bus->mapped_device = NULL;
+#ifdef CONFIG_SSB_DRIVER_PCICORE
+	bus->pcicore.setup_done = 0;
+#endif
+}
+
+static int ssb_device_suspend(struct device *dev, pm_message_t state)
+{
+	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_driver *ssb_drv;
+	struct ssb_bus *bus;
+	int err = 0;
+
+	if (dev->driver) {
+		ssb_drv = drv_to_ssb_drv(dev->driver);
+		if (ssb_drv && ssb_drv->suspend)
+			err = ssb_drv->suspend(ssb_dev, state);
+		if (err)
+			goto out;
+	}
+
+	bus = ssb_dev->bus;
+	bus->suspend_cnt++;
+	if (bus->suspend_cnt == bus->nr_devices) {
+		/* All devices suspended. Shutdown the bus. */
+		ssb_bus_suspend(bus, state);
+	}
+
+out:
+	return err;
+}
+
+#ifdef CONFIG_SSB_PCIHOST
+int ssb_devices_freeze(struct ssb_bus *bus)
+{
+	struct ssb_device *dev;
+	struct ssb_driver *drv;
+	int err = 0;
+	int i;
+	pm_message_t state = PMSG_FREEZE;
+
+	/* First check that we are capable to freeze all devices. */
+	for (i = 0; i < bus->nr_devices; i++) {
+		dev = &(bus->devices[i]);
+		if (!dev->dev ||
+		    !dev->dev->driver ||
+		    !device_is_registered(dev->dev))
+			continue;
+		drv = drv_to_ssb_drv(dev->dev->driver);
+		if (!drv)
+			continue;
+		if (!drv->suspend) {
+			/* Nope, can't suspend this one. */
+			return -EOPNOTSUPP;
+		}
+	}
+	/* Now suspend all devices */
+	for (i = 0; i < bus->nr_devices; i++) {
+		dev = &(bus->devices[i]);
+		if (!dev->dev ||
+		    !dev->dev->driver ||
+		    !device_is_registered(dev->dev))
+			continue;
+		drv = drv_to_ssb_drv(dev->dev->driver);
+		if (!drv)
+			continue;
+		err = drv->suspend(dev, state);
+		if (err) {
+			ssb_printk(KERN_ERR PFX "Failed to freeze device %s\n",
+				   dev->dev->bus_id);
+			goto err_unwind;
+		}
+	}
+
+	return 0;
+err_unwind:
+	for (i--; i >= 0; i--) {
+		dev = &(bus->devices[i]);
+		if (!dev->dev ||
+		    !dev->dev->driver ||
+		    !device_is_registered(dev->dev))
+			continue;
+		drv = drv_to_ssb_drv(dev->dev->driver);
+		if (!drv)
+			continue;
+		if (drv->resume)
+			drv->resume(dev);
+	}
+	return err;
+}
+
+int ssb_devices_thaw(struct ssb_bus *bus)
+{
+	struct ssb_device *dev;
+	struct ssb_driver *drv;
+	int err;
+	int i;
+
+	for (i = 0; i < bus->nr_devices; i++) {
+		dev = &(bus->devices[i]);
+		if (!dev->dev ||
+		    !dev->dev->driver ||
+		    !device_is_registered(dev->dev))
+			continue;
+		drv = drv_to_ssb_drv(dev->dev->driver);
+		if (!drv)
+			continue;
+		if (SSB_WARN_ON(!drv->resume))
+			continue;
+		err = drv->resume(dev);
+		if (err) {
+			ssb_printk(KERN_ERR PFX "Failed to thaw device %s\n",
+				   dev->dev->bus_id);
+		}
+	}
+
+	return 0;
+}
+#endif /* CONFIG_SSB_PCIHOST */
+
+static void ssb_device_shutdown(struct device *dev)
+{
+	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_driver *ssb_drv;
+
+	if (!dev->driver)
+		return;
+	ssb_drv = drv_to_ssb_drv(dev->driver);
+	if (ssb_drv && ssb_drv->shutdown)
+		ssb_drv->shutdown(ssb_dev);
+}
+
+static int ssb_device_remove(struct device *dev)
+{
+	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_driver *ssb_drv = drv_to_ssb_drv(dev->driver);
+
+	if (ssb_drv && ssb_drv->remove)
+		ssb_drv->remove(ssb_dev);
+	ssb_device_put(ssb_dev);
+
+	return 0;
+}
+
+static int ssb_device_probe(struct device *dev)
+{
+	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_driver *ssb_drv = drv_to_ssb_drv(dev->driver);
+	int err = 0;
+
+	ssb_device_get(ssb_dev);
+	if (ssb_drv && ssb_drv->probe)
+		err = ssb_drv->probe(ssb_dev, &ssb_dev->id);
+	if (err)
+		ssb_device_put(ssb_dev);
+
+	return err;
+}
+
+static int ssb_match_devid(const struct ssb_device_id *tabid,
+			   const struct ssb_device_id *devid)
+{
+	if ((tabid->vendor != devid->vendor) &&
+	    tabid->vendor != SSB_ANY_VENDOR)
+		return 0;
+	if ((tabid->coreid != devid->coreid) &&
+	    tabid->coreid != SSB_ANY_ID)
+		return 0;
+	if ((tabid->revision != devid->revision) &&
+	    tabid->revision != SSB_ANY_REV)
+		return 0;
+	return 1;
+}
+
+static int ssb_bus_match(struct device *dev, struct device_driver *drv)
+{
+	struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+	struct ssb_driver *ssb_drv = drv_to_ssb_drv(drv);
+	const struct ssb_device_id *id;
+
+	for (id = ssb_drv->id_table;
+	     id->vendor || id->coreid || id->revision;
+	     id++) {
+		if (ssb_match_devid(id, &ssb_dev->id))
+			return 1; /* found */
+	}
+
+	return 0;
+}
+
+static struct bus_type ssb_bustype = {
+	.name		= "ssb",
+	.match		= ssb_bus_match,
+	.probe		= ssb_device_probe,
+	.remove		= ssb_device_remove,
+	.shutdown	= ssb_device_shutdown,
+	.suspend	= ssb_device_suspend,
+	.resume		= ssb_device_resume,
+};
+
+static void ssb_buses_lock(void)
+{
+	/* See the comment at the ssb_is_early_boot definition */
+	if (!ssb_is_early_boot)
+		mutex_lock(&buses_mutex);
+}
+
+static void ssb_buses_unlock(void)
+{
+	/* See the comment at the ssb_is_early_boot definition */
+	if (!ssb_is_early_boot)
+		mutex_unlock(&buses_mutex);
+}
+
+static void ssb_devices_unregister(struct ssb_bus *bus)
+{
+	struct ssb_device *sdev;
+	int i;
+
+	for (i = bus->nr_devices - 1; i >= 0; i--) {
+		sdev = &(bus->devices[i]);
+		if (sdev->dev)
+			device_unregister(sdev->dev);
+	}
+}
+
+void ssb_bus_unregister(struct ssb_bus *bus)
+{
+	ssb_buses_lock();
+	ssb_devices_unregister(bus);
+	list_del(&bus->list);
+	ssb_buses_unlock();
+
+	/* ssb_pcmcia_exit(bus); */
+	ssb_pci_exit(bus);
+	ssb_iounmap(bus);
+}
+EXPORT_SYMBOL(ssb_bus_unregister);
+
+static void ssb_release_dev(struct device *dev)
+{
+	struct __ssb_dev_wrapper *devwrap;
+
+	devwrap = container_of(dev, struct __ssb_dev_wrapper, dev);
+	kfree(devwrap);
+}
+
+static int ssb_devices_register(struct ssb_bus *bus)
+{
+	struct ssb_device *sdev;
+	struct device *dev;
+	struct __ssb_dev_wrapper *devwrap;
+	int i, err = 0;
+	int dev_idx = 0;
+
+	for (i = 0; i < bus->nr_devices; i++) {
+		sdev = &(bus->devices[i]);
+
+		/* We don't register SSB-system devices to the kernel,
+		 * as the drivers for them are built into SSB. */
+		switch (sdev->id.coreid) {
+		case SSB_DEV_CHIPCOMMON:
+		case SSB_DEV_PCI:
+		case SSB_DEV_PCIE:
+		case SSB_DEV_PCMCIA:
+		case SSB_DEV_MIPS:
+		case SSB_DEV_MIPS_3302:
+		case SSB_DEV_EXTIF:
+			continue;
+		}
+
+		devwrap = kzalloc(sizeof(*devwrap), GFP_KERNEL);
+		if (!devwrap) {
+			ssb_printk(KERN_ERR PFX
+				   "Could not allocate device\n");
+			err = -ENOMEM;
+			goto error;
+		}
+		dev = &devwrap->dev;
+		devwrap->sdev = sdev;
+
+		dev->release = ssb_release_dev;
+		dev->bus = &ssb_bustype;
+		snprintf(dev->bus_id, sizeof(dev->bus_id),
+			 "ssb%u:%d", bus->busnumber, dev_idx);
+
+		switch (bus->bustype) {
+		case SSB_BUSTYPE_PCI:
+#ifdef CONFIG_SSB_PCIHOST
+			sdev->irq = bus->host_pci->irq;
+			dev->parent = &bus->host_pci->dev;
+#endif
+			break;
+		case SSB_BUSTYPE_PCMCIA:
+#ifdef CONFIG_SSB_PCMCIAHOST
+			dev->parent = &bus->host_pcmcia->dev;
+#endif
+			break;
+		case SSB_BUSTYPE_SSB:
+			break;
+		}
+
+		sdev->dev = dev;
+		err = device_register(dev);
+		if (err) {
+			ssb_printk(KERN_ERR PFX
+				   "Could not register %s\n",
+				   dev->bus_id);
+			/* Set dev to NULL to not unregister
+			 * dev on error unwinding. */
+			sdev->dev = NULL;
+			kfree(devwrap);
+			goto error;
+		}
+		dev_idx++;
+	}
+
+	return 0;
+error:
+	/* Unwind the already registered devices. */
+	ssb_devices_unregister(bus);
+	return err;
+}
+
+/* Needs ssb_buses_lock() */
+static int ssb_attach_queued_buses(void)
+{
+	struct ssb_bus *bus, *n;
+	int err = 0;
+	int drop_them_all = 0;
+
+	list_for_each_entry_safe(bus, n, &attach_queue, list) {
+		if (drop_them_all) {
+			list_del(&bus->list);
+			continue;
+		}
+		/* Can't init the PCIcore in ssb_bus_register(), as that
+		 * is too early in boot for embedded systems
+		 * (no udelay() available). So do it here in attach stage.
+		 */
+		ssb_pcicore_init(&bus->pcicore);
+
+		err = ssb_devices_register(bus);
+		if (err) {
+			drop_them_all = 1;
+			list_del(&bus->list);
+			continue;
+		}
+		list_move_tail(&bus->list, &buses);
+	}
+
+	return err;
+}
+
+static u16 ssb_ssb_read16(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	offset += dev->core_index * SSB_CORE_SIZE;
+	return readw(bus->mmio + offset);
+}
+
+static u32 ssb_ssb_read32(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	offset += dev->core_index * SSB_CORE_SIZE;
+	return readl(bus->mmio + offset);
+}
+
+static void ssb_ssb_write16(struct ssb_device *dev, u16 offset, u16 value)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	offset += dev->core_index * SSB_CORE_SIZE;
+	writew(value, bus->mmio + offset);
+}
+
+static void ssb_ssb_write32(struct ssb_device *dev, u16 offset, u32 value)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	offset += dev->core_index * SSB_CORE_SIZE;
+	writel(value, bus->mmio + offset);
+}
+
+/* Ops for the plain SSB bus without a host-device (no PCI or PCMCIA). */
+static const struct ssb_bus_ops ssb_ssb_ops = {
+	.read16		= ssb_ssb_read16,
+	.read32		= ssb_ssb_read32,
+	.write16	= ssb_ssb_write16,
+	.write32	= ssb_ssb_write32,
+};
+
+static int ssb_fetch_invariants(struct ssb_bus *bus,
+				ssb_invariants_func_t get_invariants)
+{
+	struct ssb_init_invariants iv;
+	int err;
+
+	memset(&iv, 0, sizeof(iv));
+	err = get_invariants(bus, &iv);
+	if (err)
+		goto out;
+	memcpy(&bus->boardinfo, &iv.boardinfo, sizeof(iv.boardinfo));
+	memcpy(&bus->sprom, &iv.sprom, sizeof(iv.sprom));
+out:
+	return err;
+}
+
+static int ssb_bus_register(struct ssb_bus *bus,
+			    ssb_invariants_func_t get_invariants,
+			    unsigned long baseaddr)
+{
+	int err;
+
+	spin_lock_init(&bus->bar_lock);
+	INIT_LIST_HEAD(&bus->list);
+
+	/* Powerup the bus */
+	err = ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 1);
+	if (err)
+		goto out;
+	ssb_buses_lock();
+	bus->busnumber = next_busnumber;
+	/* Scan for devices (cores) */
+	err = ssb_bus_scan(bus, baseaddr);
+	if (err)
+		goto err_disable_xtal;
+
+	/* Init PCI-host device (if any) */
+	err = ssb_pci_init(bus);
+	if (err)
+		goto err_unmap;
+	/* Init PCMCIA-host device (if any) */
+	err = ssb_pcmcia_init(bus);
+	if (err)
+		goto err_pci_exit;
+
+	/* Initialize basic system devices (if available) */
+	ssb_chipcommon_init(&bus->chipco);
+	ssb_mipscore_init(&bus->mipscore);
+	err = ssb_fetch_invariants(bus, get_invariants);
+	if (err)
+		goto err_pcmcia_exit;
+
+	/* Queue it for attach.
+	 * See the comment at the ssb_is_early_boot definition. */
+	list_add_tail(&bus->list, &attach_queue);
+	if (!ssb_is_early_boot) {
+		/* This is not early boot, so we must attach the bus now */
+		err = ssb_attach_queued_buses();
+		if (err)
+			goto err_dequeue;
+	}
+	next_busnumber++;
+	ssb_buses_unlock();
+
+out:
+	return err;
+
+err_dequeue:
+	list_del(&bus->list);
+err_pcmcia_exit:
+/*	ssb_pcmcia_exit(bus); */
+err_pci_exit:
+	ssb_pci_exit(bus);
+err_unmap:
+	ssb_iounmap(bus);
+err_disable_xtal:
+	ssb_buses_unlock();
+	ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 0);
+	return err;
+}
+
+#ifdef CONFIG_SSB_PCIHOST
+int ssb_bus_pcibus_register(struct ssb_bus *bus,
+			    struct pci_dev *host_pci)
+{
+	int err;
+
+	bus->bustype = SSB_BUSTYPE_PCI;
+	bus->host_pci = host_pci;
+	bus->ops = &ssb_pci_ops;
+
+	err = ssb_bus_register(bus, ssb_pci_get_invariants, 0);
+	if (!err) {
+		ssb_printk(KERN_INFO PFX "Sonics Silicon Backplane found on "
+			   "PCI device %s\n", host_pci->dev.bus_id);
+	}
+
+	return err;
+}
+EXPORT_SYMBOL(ssb_bus_pcibus_register);
+#endif /* CONFIG_SSB_PCIHOST */
+
+#ifdef CONFIG_SSB_PCMCIAHOST
+int ssb_bus_pcmciabus_register(struct ssb_bus *bus,
+			       struct pcmcia_device *pcmcia_dev,
+			       unsigned long baseaddr)
+{
+	int err;
+
+	bus->bustype = SSB_BUSTYPE_PCMCIA;
+	bus->host_pcmcia = pcmcia_dev;
+	bus->ops = &ssb_pcmcia_ops;
+
+	err = ssb_bus_register(bus, ssb_pcmcia_get_invariants, baseaddr);
+	if (!err) {
+		ssb_printk(KERN_INFO PFX "Sonics Silicon Backplane found on "
+			   "PCMCIA device %s\n", pcmcia_dev->devname);
+	}
+
+	return err;
+}
+EXPORT_SYMBOL(ssb_bus_pcmciabus_register);
+#endif /* CONFIG_SSB_PCMCIAHOST */
+
+int ssb_bus_ssbbus_register(struct ssb_bus *bus,
+			    unsigned long baseaddr,
+			    ssb_invariants_func_t get_invariants)
+{
+	int err;
+
+	bus->bustype = SSB_BUSTYPE_SSB;
+	bus->ops = &ssb_ssb_ops;
+
+	err = ssb_bus_register(bus, get_invariants, baseaddr);
+	if (!err) {
+		ssb_printk(KERN_INFO PFX "Sonics Silicon Backplane found at "
+			   "address 0x%08lX\n", baseaddr);
+	}
+
+	return err;
+}
+
+int __ssb_driver_register(struct ssb_driver *drv, struct module *owner)
+{
+	drv->drv.name = drv->name;
+	drv->drv.bus = &ssb_bustype;
+	drv->drv.owner = owner;
+
+	return driver_register(&drv->drv);
+}
+EXPORT_SYMBOL(__ssb_driver_register);
+
+void ssb_driver_unregister(struct ssb_driver *drv)
+{
+	driver_unregister(&drv->drv);
+}
+EXPORT_SYMBOL(ssb_driver_unregister);
+
+void ssb_set_devtypedata(struct ssb_device *dev, void *data)
+{
+	struct ssb_bus *bus = dev->bus;
+	struct ssb_device *ent;
+	int i;
+
+	for (i = 0; i < bus->nr_devices; i++) {
+		ent = &(bus->devices[i]);
+		if (ent->id.vendor != dev->id.vendor)
+			continue;
+		if (ent->id.coreid != dev->id.coreid)
+			continue;
+
+		ent->devtypedata = data;
+	}
+}
+EXPORT_SYMBOL(ssb_set_devtypedata);
+
+static u32 clkfactor_f6_resolve(u32 v)
+{
+	/* map the magic values */
+	switch (v) {
+	case SSB_CHIPCO_CLK_F6_2:
+		return 2;
+	case SSB_CHIPCO_CLK_F6_3:
+		return 3;
+	case SSB_CHIPCO_CLK_F6_4:
+		return 4;
+	case SSB_CHIPCO_CLK_F6_5:
+		return 5;
+	case SSB_CHIPCO_CLK_F6_6:
+		return 6;
+	case SSB_CHIPCO_CLK_F6_7:
+		return 7;
+	}
+	return 0;
+}
+
+/* Calculate the speed the backplane would run at a given set of clockcontrol values */
+u32 ssb_calc_clock_rate(u32 plltype, u32 n, u32 m)
+{
+	u32 n1, n2, clock, m1, m2, m3, mc;
+
+	n1 = (n & SSB_CHIPCO_CLK_N1);
+	n2 = ((n & SSB_CHIPCO_CLK_N2) >> SSB_CHIPCO_CLK_N2_SHIFT);
+
+	switch (plltype) {
+	case SSB_PLLTYPE_6: /* 100/200 or 120/240 only */
+		if (m & SSB_CHIPCO_CLK_T6_MMASK)
+			return SSB_CHIPCO_CLK_T6_M0;
+		return SSB_CHIPCO_CLK_T6_M1;
+	case SSB_PLLTYPE_1: /* 48Mhz base, 3 dividers */
+	case SSB_PLLTYPE_3: /* 25Mhz, 2 dividers */
+	case SSB_PLLTYPE_4: /* 48Mhz, 4 dividers */
+	case SSB_PLLTYPE_7: /* 25Mhz, 4 dividers */
+		n1 = clkfactor_f6_resolve(n1);
+		n2 += SSB_CHIPCO_CLK_F5_BIAS;
+		break;
+	case SSB_PLLTYPE_2: /* 48Mhz, 4 dividers */
+		n1 += SSB_CHIPCO_CLK_T2_BIAS;
+		n2 += SSB_CHIPCO_CLK_T2_BIAS;
+		SSB_WARN_ON(!((n1 >= 2) && (n1 <= 7)));
+		SSB_WARN_ON(!((n2 >= 5) && (n2 <= 23)));
+		break;
+	case SSB_PLLTYPE_5: /* 25Mhz, 4 dividers */
+		return 100000000;
+	default:
+		SSB_WARN_ON(1);
+	}
+
+	switch (plltype) {
+	case SSB_PLLTYPE_3: /* 25Mhz, 2 dividers */
+	case SSB_PLLTYPE_7: /* 25Mhz, 4 dividers */
+		clock = SSB_CHIPCO_CLK_BASE2 * n1 * n2;
+		break;
+	default:
+		clock = SSB_CHIPCO_CLK_BASE1 * n1 * n2;
+	}
+	if (!clock)
+		return 0;
+
+	m1 = (m & SSB_CHIPCO_CLK_M1);
+	m2 = ((m & SSB_CHIPCO_CLK_M2) >> SSB_CHIPCO_CLK_M2_SHIFT);
+	m3 = ((m & SSB_CHIPCO_CLK_M3) >> SSB_CHIPCO_CLK_M3_SHIFT);
+	mc = ((m & SSB_CHIPCO_CLK_MC) >> SSB_CHIPCO_CLK_MC_SHIFT);
+
+	switch (plltype) {
+	case SSB_PLLTYPE_1: /* 48Mhz base, 3 dividers */
+	case SSB_PLLTYPE_3: /* 25Mhz, 2 dividers */
+	case SSB_PLLTYPE_4: /* 48Mhz, 4 dividers */
+	case SSB_PLLTYPE_7: /* 25Mhz, 4 dividers */
+		m1 = clkfactor_f6_resolve(m1);
+		if ((plltype == SSB_PLLTYPE_1) ||
+		    (plltype == SSB_PLLTYPE_3))
+			m2 += SSB_CHIPCO_CLK_F5_BIAS;
+		else
+			m2 = clkfactor_f6_resolve(m2);
+		m3 = clkfactor_f6_resolve(m3);
+
+		switch (mc) {
+		case SSB_CHIPCO_CLK_MC_BYPASS:
+			return clock;
+		case SSB_CHIPCO_CLK_MC_M1:
+			return (clock / m1);
+		case SSB_CHIPCO_CLK_MC_M1M2:
+			return (clock / (m1 * m2));
+		case SSB_CHIPCO_CLK_MC_M1M2M3:
+			return (clock / (m1 * m2 * m3));
+		case SSB_CHIPCO_CLK_MC_M1M3:
+			return (clock / (m1 * m3));
+		}
+		return 0;
+	case SSB_PLLTYPE_2:
+		m1 += SSB_CHIPCO_CLK_T2_BIAS;
+		m2 += SSB_CHIPCO_CLK_T2M2_BIAS;
+		m3 += SSB_CHIPCO_CLK_T2_BIAS;
+		SSB_WARN_ON(!((m1 >= 2) && (m1 <= 7)));
+		SSB_WARN_ON(!((m2 >= 3) && (m2 <= 10)));
+		SSB_WARN_ON(!((m3 >= 2) && (m3 <= 7)));
+
+		if (!(mc & SSB_CHIPCO_CLK_T2MC_M1BYP))
+			clock /= m1;
+		if (!(mc & SSB_CHIPCO_CLK_T2MC_M2BYP))
+			clock /= m2;
+		if (!(mc & SSB_CHIPCO_CLK_T2MC_M3BYP))
+			clock /= m3;
+		return clock;
+	default:
+		SSB_WARN_ON(1);
+	}
+	return 0;
+}
+
+/* Get the current speed the backplane is running at */
+u32 ssb_clockspeed(struct ssb_bus *bus)
+{
+	u32 rate;
+	u32 plltype;
+	u32 clkctl_n, clkctl_m;
+
+	//TODO if EXTIF: PLLTYPE == 1, read n from clockcontrol_n, m from clockcontrol_sb
+
+	if (bus->chipco.dev) {
+		ssb_chipco_get_clockcontrol(&bus->chipco, &plltype,
+					    &clkctl_n, &clkctl_m);
+	} else
+		return 0;
+
+	if (bus->chip_id == 0x5365) {
+		rate = 100000000;
+	} else {
+		rate = ssb_calc_clock_rate(plltype, clkctl_n, clkctl_m);
+		if (plltype == SSB_PLLTYPE_3) /* 25Mhz, 2 dividers */
+			rate /= 2;
+	}
+
+	return rate;
+}
+EXPORT_SYMBOL(ssb_clockspeed);
+
+static u32 ssb_tmslow_reject_bitmask(struct ssb_device *dev)
+{
+	/* The REJECT bit changed position in TMSLOW between
+	 * Backplane revisions. */
+	switch (ssb_read32(dev, SSB_IDLOW) & SSB_IDLOW_SSBREV) {
+	case SSB_IDLOW_SSBREV_22:
+		return SSB_TMSLOW_REJECT_22;
+	case SSB_IDLOW_SSBREV_23:
+		return SSB_TMSLOW_REJECT_23;
+	default:
+		WARN_ON(1);
+	}
+	return (SSB_TMSLOW_REJECT_22 | SSB_TMSLOW_REJECT_23);
+}
+
+int ssb_device_is_enabled(struct ssb_device *dev)
+{
+	u32 val;
+	u32 reject;
+
+	reject = ssb_tmslow_reject_bitmask(dev);
+	val = ssb_read32(dev, SSB_TMSLOW);
+	val &= SSB_TMSLOW_CLOCK | SSB_TMSLOW_RESET | reject;
+
+	return (val == SSB_TMSLOW_CLOCK);
+}
+EXPORT_SYMBOL(ssb_device_is_enabled);
+
+static void ssb_flush_tmslow(struct ssb_device *dev)
+{
+	/* Make _really_ sure the device has finished the TMSLOW
+	 * register write transaction, as we risk running into
+	 * a machine check exception otherwise.
+	 * Do this by reading the register back to commit the
+	 * PCI write and delay an additional usec for the device
+	 * to react to the change. */
+	ssb_read32(dev, SSB_TMSLOW);
+	udelay(1);
+}
+
+void ssb_device_enable(struct ssb_device *dev, u32 core_specific_flags)
+{
+	u32 val;
+
+	ssb_device_disable(dev, core_specific_flags);
+	ssb_write32(dev, SSB_TMSLOW,
+		    SSB_TMSLOW_RESET | SSB_TMSLOW_CLOCK |
+		    SSB_TMSLOW_FGC | core_specific_flags);
+	ssb_flush_tmslow(dev);
+
+	/* Clear SERR if set. This is a hw bug workaround. */
+	if (ssb_read32(dev, SSB_TMSHIGH) & SSB_TMSHIGH_SERR)
+		ssb_write32(dev, SSB_TMSHIGH, 0);
+
+	val = ssb_read32(dev, SSB_IMSTATE);
+	if (val & (SSB_IMSTATE_IBE | SSB_IMSTATE_TO)) {
+		val &= ~(SSB_IMSTATE_IBE | SSB_IMSTATE_TO);
+		ssb_write32(dev, SSB_IMSTATE, val);
+	}
+
+	ssb_write32(dev, SSB_TMSLOW,
+		    SSB_TMSLOW_CLOCK | SSB_TMSLOW_FGC |
+		    core_specific_flags);
+	ssb_flush_tmslow(dev);
+
+	ssb_write32(dev, SSB_TMSLOW, SSB_TMSLOW_CLOCK |
+		    core_specific_flags);
+	ssb_flush_tmslow(dev);
+}
+EXPORT_SYMBOL(ssb_device_enable);
+
+/* Wait for a bit in a register to get set or unset.
+ * timeout is in units of ten-microseconds */
+static int ssb_wait_bit(struct ssb_device *dev, u16 reg, u32 bitmask,
+			int timeout, int set)
+{
+	int i;
+	u32 val;
+
+	for (i = 0; i < timeout; i++) {
+		val = ssb_read32(dev, reg);
+		if (set) {
+			if (val & bitmask)
+				return 0;
+		} else {
+			if (!(val & bitmask))
+				return 0;
+		}
+		udelay(10);
+	}
+	printk(KERN_ERR PFX "Timeout waiting for bitmask %08X on "
+			    "register %04X to %s.\n",
+	       bitmask, reg, (set ? "set" : "clear"));
+
+	return -ETIMEDOUT;
+}
+
+void ssb_device_disable(struct ssb_device *dev, u32 core_specific_flags)
+{
+	u32 reject;
+
+	if (ssb_read32(dev, SSB_TMSLOW) & SSB_TMSLOW_RESET)
+		return;
+
+	reject = ssb_tmslow_reject_bitmask(dev);
+	ssb_write32(dev, SSB_TMSLOW, reject | SSB_TMSLOW_CLOCK);
+	ssb_wait_bit(dev, SSB_TMSLOW, reject, 1000, 1);
+	ssb_wait_bit(dev, SSB_TMSHIGH, SSB_TMSHIGH_BUSY, 1000, 0);
+	ssb_write32(dev, SSB_TMSLOW,
+		    SSB_TMSLOW_FGC | SSB_TMSLOW_CLOCK |
+		    reject | SSB_TMSLOW_RESET |
+		    core_specific_flags);
+	ssb_flush_tmslow(dev);
+
+	ssb_write32(dev, SSB_TMSLOW,
+		    reject | SSB_TMSLOW_RESET |
+		    core_specific_flags);
+	ssb_flush_tmslow(dev);
+}
+EXPORT_SYMBOL(ssb_device_disable);
+
+u32 ssb_dma_translation(struct ssb_device *dev)
+{
+	switch (dev->bus->bustype) {
+	case SSB_BUSTYPE_SSB:
+		return 0;
+	case SSB_BUSTYPE_PCI:
+	case SSB_BUSTYPE_PCMCIA:
+		return SSB_PCI_DMA;
+	}
+	return 0;
+}
+EXPORT_SYMBOL(ssb_dma_translation);
+
+int ssb_dma_set_mask(struct ssb_device *ssb_dev, u64 mask)
+{
+	struct device *dev = ssb_dev->dev;
+
+#ifdef CONFIG_SSB_PCIHOST
+	if (ssb_dev->bus->bustype == SSB_BUSTYPE_PCI &&
+	    !dma_supported(dev, mask))
+		return -EIO;
+#endif
+	dev->coherent_dma_mask = mask;
+	dev->dma_mask = &dev->coherent_dma_mask;
+
+	return 0;
+}
+EXPORT_SYMBOL(ssb_dma_set_mask);
+
+int ssb_bus_may_powerdown(struct ssb_bus *bus)
+{
+	struct ssb_chipcommon *cc;
+	int err;
+
+	/* On buses where more than one core may be working
+	 * at a time, we must not powerdown stuff if there are
+	 * still cores that may want to run. */
+	if (bus->bustype == SSB_BUSTYPE_SSB)
+		return 0;
+
+	cc = &bus->chipco;
+	ssb_chipco_set_clockmode(cc, SSB_CLKMODE_SLOW);
+	err = ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 0);
+	if (err)
+		goto error;
+
+	return 0;
+error:
+	ssb_printk(KERN_ERR PFX "Bus powerdown failed\n");
+	return err;
+}
+EXPORT_SYMBOL(ssb_bus_may_powerdown);
+
+int ssb_bus_powerup(struct ssb_bus *bus, bool dynamic_pctl)
+{
+	struct ssb_chipcommon *cc;
+	int err;
+	enum ssb_clkmode mode;
+
+	err = ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 1);
+	if (err)
+		goto error;
+	cc = &bus->chipco;
+	mode = dynamic_pctl ? SSB_CLKMODE_DYNAMIC : SSB_CLKMODE_FAST;
+	ssb_chipco_set_clockmode(cc, mode);
+
+	return 0;
+error:
+	ssb_printk(KERN_ERR PFX "Bus powerup failed\n");
+	return err;
+}
+EXPORT_SYMBOL(ssb_bus_powerup);
+
+u32 ssb_admatch_base(u32 adm)
+{
+	u32 base = 0;
+
+	switch (adm & SSB_ADM_TYPE) {
+	case SSB_ADM_TYPE0:
+		base = (adm & SSB_ADM_BASE0);
+		break;
+	case SSB_ADM_TYPE1:
+		SSB_WARN_ON(adm & SSB_ADM_NEG); /* unsupported */
+		base = (adm & SSB_ADM_BASE1);
+		break;
+	case SSB_ADM_TYPE2:
+		SSB_WARN_ON(adm & SSB_ADM_NEG); /* unsupported */
+		base = (adm & SSB_ADM_BASE2);
+		break;
+	default:
+		SSB_WARN_ON(1);
+	}
+
+	return base;
+}
+EXPORT_SYMBOL(ssb_admatch_base);
+
+u32 ssb_admatch_size(u32 adm)
+{
+	u32 size = 0;
+
+	switch (adm & SSB_ADM_TYPE) {
+	case SSB_ADM_TYPE0:
+		size = ((adm & SSB_ADM_SZ0) >> SSB_ADM_SZ0_SHIFT);
+		break;
+	case SSB_ADM_TYPE1:
+		SSB_WARN_ON(adm & SSB_ADM_NEG); /* unsupported */
+		size = ((adm & SSB_ADM_SZ1) >> SSB_ADM_SZ1_SHIFT);
+		break;
+	case SSB_ADM_TYPE2:
+		SSB_WARN_ON(adm & SSB_ADM_NEG); /* unsupported */
+		size = ((adm & SSB_ADM_SZ2) >> SSB_ADM_SZ2_SHIFT);
+		break;
+	default:
+		SSB_WARN_ON(1);
+	}
+	size = (1 << (size + 1));
+
+	return size;
+}
+EXPORT_SYMBOL(ssb_admatch_size);
+
+static int __init ssb_modinit(void)
+{
+	int err;
+
+	/* See the comment at the ssb_is_early_boot definition */
+	ssb_is_early_boot = 0;
+	err = bus_register(&ssb_bustype);
+	if (err)
+		return err;
+
+	/* Maybe we already registered some buses at early boot.
+	 * Check for this and attach them
+	 */
+	ssb_buses_lock();
+	err = ssb_attach_queued_buses();
+	ssb_buses_unlock();
+	if (err)
+		bus_unregister(&ssb_bustype);
+
+	return err;
+}
+subsys_initcall(ssb_modinit);
+
+static void __exit ssb_modexit(void)
+{
+	bus_unregister(&ssb_bustype);
+}
+module_exit(ssb_modexit)
diff --git a/drivers/ssb/pci.c b/drivers/ssb/pci.c
new file mode 100644
index 0000000..b3ec4c8
--- /dev/null
+++ b/drivers/ssb/pci.c
@@ -0,0 +1,704 @@
+/*
+ * Sonics Silicon Backplane PCI-Hostbus related functions.
+ *
+ * Copyright (C) 2005-2006 Michael Buesch <[email protected]>
+ * Copyright (C) 2005 Martin Langer <[email protected]>
+ * Copyright (C) 2005 Stefano Brivio <[email protected]>
+ * Copyright (C) 2005 Danny van Dyk <[email protected]>
+ * Copyright (C) 2005 Andreas Jaggi <[email protected]>
+ *
+ * Derived from the Broadcom 4400 device driver.
+ * Copyright (C) 2002 David S. Miller ([email protected])
+ * Fixed by Pekka Pietikainen ([email protected])
+ * Copyright (C) 2006 Broadcom Corporation.
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/ssb/ssb.h>
+#include <linux/ssb/ssb_regs.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+
+#include "ssb_private.h"
+
+
+/* Lowlevel coreswitching */
+int ssb_pci_switch_coreidx(struct ssb_bus *bus, u8 coreidx)
+{
+	int err;
+	int attempts = 0;
+	u32 cur_core;
+
+	while (1) {
+		err = pci_write_config_dword(bus->host_pci, SSB_BAR0_WIN,
+					     (coreidx * SSB_CORE_SIZE)
+					     + SSB_ENUM_BASE);
+		if (err)
+			goto error;
+		err = pci_read_config_dword(bus->host_pci, SSB_BAR0_WIN,
+					    &cur_core);
+		if (err)
+			goto error;
+		cur_core = (cur_core - SSB_ENUM_BASE)
+			   / SSB_CORE_SIZE;
+		if (cur_core == coreidx)
+			break;
+
+		if (attempts++ > SSB_BAR0_MAX_RETRIES)
+			goto error;
+		udelay(10);
+	}
+	return 0;
+error:
+	ssb_printk(KERN_ERR PFX "Failed to switch to core %u\n", coreidx);
+	return -ENODEV;
+}
+
+int ssb_pci_switch_core(struct ssb_bus *bus,
+			struct ssb_device *dev)
+{
+	int err;
+	unsigned long flags;
+
+	ssb_dprintk(KERN_INFO PFX
+		    "Switching to %s core, index %d\n",
+		    ssb_core_name(dev->id.coreid),
+		    dev->core_index);
+
+	spin_lock_irqsave(&bus->bar_lock, flags);
+	err = ssb_pci_switch_coreidx(bus, dev->core_index);
+	if (!err)
+		bus->mapped_device = dev;
+	spin_unlock_irqrestore(&bus->bar_lock, flags);
+
+	return err;
+}
+
+/* Enable/disable the on board crystal oscillator and/or PLL. */
+int ssb_pci_xtal(struct ssb_bus *bus, u32 what, int turn_on)
+{
+	int err;
+	u32 in, out, outenable;
+	u16 pci_status;
+
+	if (bus->bustype != SSB_BUSTYPE_PCI)
+		return 0;
+
+	err = pci_read_config_dword(bus->host_pci, SSB_GPIO_IN, &in);
+	if (err)
+		goto err_pci;
+	err = pci_read_config_dword(bus->host_pci, SSB_GPIO_OUT, &out);
+	if (err)
+		goto err_pci;
+	err = pci_read_config_dword(bus->host_pci, SSB_GPIO_OUT_ENABLE, &outenable);
+	if (err)
+		goto err_pci;
+
+	outenable |= what;
+
+	if (turn_on) {
+		/* Avoid glitching the clock if GPRS is already using it.
+		 * We can't actually read the state of the PLLPD so we infer it
+		 * by the value of XTAL_PU which *is* readable via gpioin.
+		 */
+		if (!(in & SSB_GPIO_XTAL)) {
+			if (what & SSB_GPIO_XTAL) {
+				/* Turn the crystal on */
+				out |= SSB_GPIO_XTAL;
+				if (what & SSB_GPIO_PLL)
+					out |= SSB_GPIO_PLL;
+				err = pci_write_config_dword(bus->host_pci, SSB_GPIO_OUT, out);
+				if (err)
+					goto err_pci;
+				err = pci_write_config_dword(bus->host_pci, SSB_GPIO_OUT_ENABLE,
+							     outenable);
+				if (err)
+					goto err_pci;
+				msleep(1);
+			}
+			if (what & SSB_GPIO_PLL) {
+				/* Turn the PLL on */
+				out &= ~SSB_GPIO_PLL;
+				err = pci_write_config_dword(bus->host_pci, SSB_GPIO_OUT, out);
+				if (err)
+					goto err_pci;
+				msleep(5);
+			}
+		}
+
+		err = pci_read_config_word(bus->host_pci, PCI_STATUS, &pci_status);
+		if (err)
+			goto err_pci;
+		pci_status &= ~PCI_STATUS_SIG_TARGET_ABORT;
+		err = pci_write_config_word(bus->host_pci, PCI_STATUS, pci_status);
+		if (err)
+			goto err_pci;
+	} else {
+		if (what & SSB_GPIO_XTAL) {
+			/* Turn the crystal off */
+			out &= ~SSB_GPIO_XTAL;
+		}
+		if (what & SSB_GPIO_PLL) {
+			/* Turn the PLL off */
+			out |= SSB_GPIO_PLL;
+		}
+		err = pci_write_config_dword(bus->host_pci, SSB_GPIO_OUT, out);
+		if (err)
+			goto err_pci;
+		err = pci_write_config_dword(bus->host_pci, SSB_GPIO_OUT_ENABLE, outenable);
+		if (err)
+			goto err_pci;
+	}
+
+out:
+	return err;
+
+err_pci:
+	printk(KERN_ERR PFX "Error: ssb_pci_xtal() could not access PCI config space!\n");
+	err = -EBUSY;
+	goto out;
+}
+
+/* Get the word-offset for a SSB_SPROM_XXX define. */
+#define SPOFF(offset)	(((offset) - SSB_SPROM_BASE) / sizeof(u16))
+/* Helper to extract some _offset, which is one of the SSB_SPROM_XXX defines. */
+#define SPEX(_outvar, _offset, _mask, _shift)	\
+	out->_outvar = ((in[SPOFF(_offset)] & (_mask)) >> (_shift))
+
+static inline u8 ssb_crc8(u8 crc, u8 data)
+{
+	/* Polynomial:   x^8 + x^7 + x^6 + x^4 + x^2 + 1   */
+	static const u8 t[] = {
+		0x00, 0xF7, 0xB9, 0x4E, 0x25, 0xD2, 0x9C, 0x6B,
+		0x4A, 0xBD, 0xF3, 0x04, 0x6F, 0x98, 0xD6, 0x21,
+		0x94, 0x63, 0x2D, 0xDA, 0xB1, 0x46, 0x08, 0xFF,
+		0xDE, 0x29, 0x67, 0x90, 0xFB, 0x0C, 0x42, 0xB5,
+		0x7F, 0x88, 0xC6, 0x31, 0x5A, 0xAD, 0xE3, 0x14,
+		0x35, 0xC2, 0x8C, 0x7B, 0x10, 0xE7, 0xA9, 0x5E,
+		0xEB, 0x1C, 0x52, 0xA5, 0xCE, 0x39, 0x77, 0x80,
+		0xA1, 0x56, 0x18, 0xEF, 0x84, 0x73, 0x3D, 0xCA,
+		0xFE, 0x09, 0x47, 0xB0, 0xDB, 0x2C, 0x62, 0x95,
+		0xB4, 0x43, 0x0D, 0xFA, 0x91, 0x66, 0x28, 0xDF,
+		0x6A, 0x9D, 0xD3, 0x24, 0x4F, 0xB8, 0xF6, 0x01,
+		0x20, 0xD7, 0x99, 0x6E, 0x05, 0xF2, 0xBC, 0x4B,
+		0x81, 0x76, 0x38, 0xCF, 0xA4, 0x53, 0x1D, 0xEA,
+		0xCB, 0x3C, 0x72, 0x85, 0xEE, 0x19, 0x57, 0xA0,
+		0x15, 0xE2, 0xAC, 0x5B, 0x30, 0xC7, 0x89, 0x7E,
+		0x5F, 0xA8, 0xE6, 0x11, 0x7A, 0x8D, 0xC3, 0x34,
+		0xAB, 0x5C, 0x12, 0xE5, 0x8E, 0x79, 0x37, 0xC0,
+		0xE1, 0x16, 0x58, 0xAF, 0xC4, 0x33, 0x7D, 0x8A,
+		0x3F, 0xC8, 0x86, 0x71, 0x1A, 0xED, 0xA3, 0x54,
+		0x75, 0x82, 0xCC, 0x3B, 0x50, 0xA7, 0xE9, 0x1E,
+		0xD4, 0x23, 0x6D, 0x9A, 0xF1, 0x06, 0x48, 0xBF,
+		0x9E, 0x69, 0x27, 0xD0, 0xBB, 0x4C, 0x02, 0xF5,
+		0x40, 0xB7, 0xF9, 0x0E, 0x65, 0x92, 0xDC, 0x2B,
+		0x0A, 0xFD, 0xB3, 0x44, 0x2F, 0xD8, 0x96, 0x61,
+		0x55, 0xA2, 0xEC, 0x1B, 0x70, 0x87, 0xC9, 0x3E,
+		0x1F, 0xE8, 0xA6, 0x51, 0x3A, 0xCD, 0x83, 0x74,
+		0xC1, 0x36, 0x78, 0x8F, 0xE4, 0x13, 0x5D, 0xAA,
+		0x8B, 0x7C, 0x32, 0xC5, 0xAE, 0x59, 0x17, 0xE0,
+		0x2A, 0xDD, 0x93, 0x64, 0x0F, 0xF8, 0xB6, 0x41,
+		0x60, 0x97, 0xD9, 0x2E, 0x45, 0xB2, 0xFC, 0x0B,
+		0xBE, 0x49, 0x07, 0xF0, 0x9B, 0x6C, 0x22, 0xD5,
+		0xF4, 0x03, 0x4D, 0xBA, 0xD1, 0x26, 0x68, 0x9F,
+	};
+	return t[crc ^ data];
+}
+
+static u8 ssb_sprom_crc(const u16 *sprom)
+{
+	int word;
+	u8 crc = 0xFF;
+
+	for (word = 0; word < SSB_SPROMSIZE_WORDS - 1; word++) {
+		crc = ssb_crc8(crc, sprom[word] & 0x00FF);
+		crc = ssb_crc8(crc, (sprom[word] & 0xFF00) >> 8);
+	}
+	crc = ssb_crc8(crc, sprom[SPOFF(SSB_SPROM_REVISION)] & 0x00FF);
+	crc ^= 0xFF;
+
+	return crc;
+}
+
+static int sprom_check_crc(const u16 *sprom)
+{
+	u8 crc;
+	u8 expected_crc;
+	u16 tmp;
+
+	crc = ssb_sprom_crc(sprom);
+	tmp = sprom[SPOFF(SSB_SPROM_REVISION)] & SSB_SPROM_REVISION_CRC;
+	expected_crc = tmp >> SSB_SPROM_REVISION_CRC_SHIFT;
+	if (crc != expected_crc)
+		return -EPROTO;
+
+	return 0;
+}
+
+static void sprom_do_read(struct ssb_bus *bus, u16 *sprom)
+{
+	int i;
+
+	for (i = 0; i < SSB_SPROMSIZE_WORDS; i++)
+		sprom[i] = readw(bus->mmio + SSB_SPROM_BASE + (i * 2));
+}
+
+static int sprom_do_write(struct ssb_bus *bus, const u16 *sprom)
+{
+	struct pci_dev *pdev = bus->host_pci;
+	int i, err;
+	u32 spromctl;
+
+	ssb_printk(KERN_NOTICE PFX "Writing SPROM. Do NOT turn off the power! Please stand by...\n");
+	err = pci_read_config_dword(pdev, SSB_SPROMCTL, &spromctl);
+	if (err)
+		goto err_ctlreg;
+	spromctl |= SSB_SPROMCTL_WE;
+	err = pci_write_config_dword(pdev, SSB_SPROMCTL, spromctl);
+	if (err)
+		goto err_ctlreg;
+	ssb_printk(KERN_NOTICE PFX "[ 0%%");
+	msleep(500);
+	for (i = 0; i < SSB_SPROMSIZE_WORDS; i++) {
+		if (i == SSB_SPROMSIZE_WORDS / 4)
+			ssb_printk("25%%");
+		else if (i == SSB_SPROMSIZE_WORDS / 2)
+			ssb_printk("50%%");
+		else if (i == (SSB_SPROMSIZE_WORDS / 4) * 3)
+			ssb_printk("75%%");
+		else if (i % 2)
+			ssb_printk(".");
+		writew(sprom[i], bus->mmio + SSB_SPROM_BASE + (i * 2));
+		mmiowb();
+		msleep(20);
+	}
+	err = pci_read_config_dword(pdev, SSB_SPROMCTL, &spromctl);
+	if (err)
+		goto err_ctlreg;
+	spromctl &= ~SSB_SPROMCTL_WE;
+	err = pci_write_config_dword(pdev, SSB_SPROMCTL, spromctl);
+	if (err)
+		goto err_ctlreg;
+	msleep(500);
+	ssb_printk("100%% ]\n");
+	ssb_printk(KERN_NOTICE PFX "SPROM written.\n");
+
+	return 0;
+err_ctlreg:
+	ssb_printk(KERN_ERR PFX "Could not access SPROM control register.\n");
+	return err;
+}
+
+static void sprom_extract_r1(struct ssb_sprom_r1 *out, const u16 *in)
+{
+	int i;
+	u16 v;
+
+	SPEX(pci_spid, SSB_SPROM1_SPID, 0xFFFF, 0);
+	SPEX(pci_svid, SSB_SPROM1_SVID, 0xFFFF, 0);
+	SPEX(pci_pid, SSB_SPROM1_PID, 0xFFFF, 0);
+	for (i = 0; i < 3; i++) {
+		v = in[SPOFF(SSB_SPROM1_IL0MAC) + i];
+		*(((u16 *)out->il0mac) + i) = cpu_to_be16(v);
+	}
+	for (i = 0; i < 3; i++) {
+		v = in[SPOFF(SSB_SPROM1_ET0MAC) + i];
+		*(((u16 *)out->et0mac) + i) = cpu_to_be16(v);
+	}
+	for (i = 0; i < 3; i++) {
+		v = in[SPOFF(SSB_SPROM1_ET1MAC) + i];
+		*(((u16 *)out->et1mac) + i) = cpu_to_be16(v);
+	}
+	SPEX(et0phyaddr, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET0A, 0);
+	SPEX(et1phyaddr, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET1A,
+	     SSB_SPROM1_ETHPHY_ET1A_SHIFT);
+	SPEX(et0mdcport, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET0M, 14);
+	SPEX(et1mdcport, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET1M, 15);
+	SPEX(board_rev, SSB_SPROM1_BINF, SSB_SPROM1_BINF_BREV, 0);
+	SPEX(country_code, SSB_SPROM1_BINF, SSB_SPROM1_BINF_CCODE,
+	     SSB_SPROM1_BINF_CCODE_SHIFT);
+	SPEX(antenna_a, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTA,
+	     SSB_SPROM1_BINF_ANTA_SHIFT);
+	SPEX(antenna_bg, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTBG,
+	     SSB_SPROM1_BINF_ANTBG_SHIFT);
+	SPEX(pa0b0, SSB_SPROM1_PA0B0, 0xFFFF, 0);
+	SPEX(pa0b1, SSB_SPROM1_PA0B1, 0xFFFF, 0);
+	SPEX(pa0b2, SSB_SPROM1_PA0B2, 0xFFFF, 0);
+	SPEX(pa1b0, SSB_SPROM1_PA1B0, 0xFFFF, 0);
+	SPEX(pa1b1, SSB_SPROM1_PA1B1, 0xFFFF, 0);
+	SPEX(pa1b2, SSB_SPROM1_PA1B2, 0xFFFF, 0);
+	SPEX(gpio0, SSB_SPROM1_GPIOA, SSB_SPROM1_GPIOA_P0, 0);
+	SPEX(gpio1, SSB_SPROM1_GPIOA, SSB_SPROM1_GPIOA_P1,
+	     SSB_SPROM1_GPIOA_P1_SHIFT);
+	SPEX(gpio2, SSB_SPROM1_GPIOB, SSB_SPROM1_GPIOB_P2, 0);
+	SPEX(gpio3, SSB_SPROM1_GPIOB, SSB_SPROM1_GPIOB_P3,
+	     SSB_SPROM1_GPIOB_P3_SHIFT);
+	SPEX(maxpwr_a, SSB_SPROM1_MAXPWR, SSB_SPROM1_MAXPWR_A,
+	     SSB_SPROM1_MAXPWR_A_SHIFT);
+	SPEX(maxpwr_bg, SSB_SPROM1_MAXPWR, SSB_SPROM1_MAXPWR_BG, 0);
+	SPEX(itssi_a, SSB_SPROM1_ITSSI, SSB_SPROM1_ITSSI_A,
+	     SSB_SPROM1_ITSSI_A_SHIFT);
+	SPEX(itssi_bg, SSB_SPROM1_ITSSI, SSB_SPROM1_ITSSI_BG, 0);
+	SPEX(boardflags_lo, SSB_SPROM1_BFLLO, 0xFFFF, 0);
+	SPEX(antenna_gain_a, SSB_SPROM1_AGAIN, SSB_SPROM1_AGAIN_A, 0);
+	SPEX(antenna_gain_bg, SSB_SPROM1_AGAIN, SSB_SPROM1_AGAIN_BG,
+	     SSB_SPROM1_AGAIN_BG_SHIFT);
+	for (i = 0; i < 4; i++) {
+		v = in[SPOFF(SSB_SPROM1_OEM) + i];
+		*(((u16 *)out->oem) + i) = cpu_to_le16(v);
+	}
+}
+
+static void sprom_extract_r2(struct ssb_sprom_r2 *out, const u16 *in)
+{
+	int i;
+	u16 v;
+
+	SPEX(boardflags_hi, SSB_SPROM2_BFLHI,  0xFFFF, 0);
+	SPEX(maxpwr_a_hi, SSB_SPROM2_MAXP_A, SSB_SPROM2_MAXP_A_HI, 0);
+	SPEX(maxpwr_a_lo, SSB_SPROM2_MAXP_A, SSB_SPROM2_MAXP_A_LO,
+	     SSB_SPROM2_MAXP_A_LO_SHIFT);
+	SPEX(pa1lob0, SSB_SPROM2_PA1LOB0, 0xFFFF, 0);
+	SPEX(pa1lob1, SSB_SPROM2_PA1LOB1, 0xFFFF, 0);
+	SPEX(pa1lob2, SSB_SPROM2_PA1LOB2, 0xFFFF, 0);
+	SPEX(pa1hib0, SSB_SPROM2_PA1HIB0, 0xFFFF, 0);
+	SPEX(pa1hib1, SSB_SPROM2_PA1HIB1, 0xFFFF, 0);
+	SPEX(pa1hib2, SSB_SPROM2_PA1HIB2, 0xFFFF, 0);
+	SPEX(ofdm_pwr_off, SSB_SPROM2_OPO, SSB_SPROM2_OPO_VALUE, 0);
+	for (i = 0; i < 4; i++) {
+		v = in[SPOFF(SSB_SPROM2_CCODE) + i];
+		*(((u16 *)out->country_str) + i) = cpu_to_le16(v);
+	}
+}
+
+static void sprom_extract_r3(struct ssb_sprom_r3 *out, const u16 *in)
+{
+	out->ofdmapo  = (in[SPOFF(SSB_SPROM3_OFDMAPO) + 0] & 0xFF00) >> 8;
+	out->ofdmapo |= (in[SPOFF(SSB_SPROM3_OFDMAPO) + 0] & 0x00FF) << 8;
+	out->ofdmapo <<= 16;
+	out->ofdmapo |= (in[SPOFF(SSB_SPROM3_OFDMAPO) + 1] & 0xFF00) >> 8;
+	out->ofdmapo |= (in[SPOFF(SSB_SPROM3_OFDMAPO) + 1] & 0x00FF) << 8;
+
+	out->ofdmalpo  = (in[SPOFF(SSB_SPROM3_OFDMALPO) + 0] & 0xFF00) >> 8;
+	out->ofdmalpo |= (in[SPOFF(SSB_SPROM3_OFDMALPO) + 0] & 0x00FF) << 8;
+	out->ofdmalpo <<= 16;
+	out->ofdmalpo |= (in[SPOFF(SSB_SPROM3_OFDMALPO) + 1] & 0xFF00) >> 8;
+	out->ofdmalpo |= (in[SPOFF(SSB_SPROM3_OFDMALPO) + 1] & 0x00FF) << 8;
+
+	out->ofdmahpo  = (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 0] & 0xFF00) >> 8;
+	out->ofdmahpo |= (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 0] & 0x00FF) << 8;
+	out->ofdmahpo <<= 16;
+	out->ofdmahpo |= (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 1] & 0xFF00) >> 8;
+	out->ofdmahpo |= (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 1] & 0x00FF) << 8;
+
+	SPEX(gpioldc_on_cnt, SSB_SPROM3_GPIOLDC, SSB_SPROM3_GPIOLDC_ON,
+	     SSB_SPROM3_GPIOLDC_ON_SHIFT);
+	SPEX(gpioldc_off_cnt, SSB_SPROM3_GPIOLDC, SSB_SPROM3_GPIOLDC_OFF,
+	     SSB_SPROM3_GPIOLDC_OFF_SHIFT);
+	SPEX(cckpo_1M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_1M, 0);
+	SPEX(cckpo_2M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_2M,
+	     SSB_SPROM3_CCKPO_2M_SHIFT);
+	SPEX(cckpo_55M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_55M,
+	     SSB_SPROM3_CCKPO_55M_SHIFT);
+	SPEX(cckpo_11M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_11M,
+	     SSB_SPROM3_CCKPO_11M_SHIFT);
+
+	out->ofdmgpo  = (in[SPOFF(SSB_SPROM3_OFDMGPO) + 0] & 0xFF00) >> 8;
+	out->ofdmgpo |= (in[SPOFF(SSB_SPROM3_OFDMGPO) + 0] & 0x00FF) << 8;
+	out->ofdmgpo <<= 16;
+	out->ofdmgpo |= (in[SPOFF(SSB_SPROM3_OFDMGPO) + 1] & 0xFF00) >> 8;
+	out->ofdmgpo |= (in[SPOFF(SSB_SPROM3_OFDMGPO) + 1] & 0x00FF) << 8;
+}
+
+static int sprom_extract(struct ssb_bus *bus,
+			 struct ssb_sprom *out, const u16 *in)
+{
+	memset(out, 0, sizeof(*out));
+
+	SPEX(revision, SSB_SPROM_REVISION, SSB_SPROM_REVISION_REV, 0);
+	SPEX(crc, SSB_SPROM_REVISION, SSB_SPROM_REVISION_CRC,
+	     SSB_SPROM_REVISION_CRC_SHIFT);
+
+	if ((bus->chip_id & 0xFF00) == 0x4400) {
+		/* Workaround: The BCM44XX chip has a stupid revision
+		 * number stored in the SPROM.
+		 * Always extract r1. */
+		sprom_extract_r1(&out->r1, in);
+	} else {
+		if (out->revision == 0)
+			goto unsupported;
+		if (out->revision >= 1 && out->revision <= 3)
+			sprom_extract_r1(&out->r1, in);
+		if (out->revision >= 2 && out->revision <= 3)
+			sprom_extract_r2(&out->r2, in);
+		if (out->revision == 3)
+			sprom_extract_r3(&out->r3, in);
+		if (out->revision >= 4)
+			goto unsupported;
+	}
+
+	return 0;
+unsupported:
+	ssb_printk(KERN_WARNING PFX "Unsupported SPROM revision %d "
+		   "detected. Will extract v1\n", out->revision);
+	sprom_extract_r1(&out->r1, in);
+	return 0;
+}
+
+static int ssb_pci_sprom_get(struct ssb_bus *bus,
+			     struct ssb_sprom *sprom)
+{
+	int err = -ENOMEM;
+	u16 *buf;
+
+	buf = kcalloc(SSB_SPROMSIZE_WORDS, sizeof(u16), GFP_KERNEL);
+	if (!buf)
+		goto out;
+	sprom_do_read(bus, buf);
+	err = sprom_check_crc(buf);
+	if (err) {
+		ssb_printk(KERN_WARNING PFX
+			   "WARNING: Invalid SPROM CRC (corrupt SPROM)\n");
+	}
+	err = sprom_extract(bus, sprom, buf);
+
+	kfree(buf);
+out:
+	return err;
+}
+
+static void ssb_pci_get_boardinfo(struct ssb_bus *bus,
+				  struct ssb_boardinfo *bi)
+{
+	pci_read_config_word(bus->host_pci, PCI_SUBSYSTEM_VENDOR_ID,
+			     &bi->vendor);
+	pci_read_config_word(bus->host_pci, PCI_SUBSYSTEM_ID,
+			     &bi->type);
+	pci_read_config_word(bus->host_pci, PCI_REVISION_ID,
+			     &bi->rev);
+}
+
+int ssb_pci_get_invariants(struct ssb_bus *bus,
+			   struct ssb_init_invariants *iv)
+{
+	int err;
+
+	err = ssb_pci_sprom_get(bus, &iv->sprom);
+	if (err)
+		goto out;
+	ssb_pci_get_boardinfo(bus, &iv->boardinfo);
+
+out:
+	return err;
+}
+
+static u16 ssb_pci_read16(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	if (unlikely(bus->mapped_device != dev)) {
+		if (unlikely(ssb_pci_switch_core(bus, dev)))
+			return 0xFFFF;
+	}
+	return readw(bus->mmio + offset);
+}
+
+static u32 ssb_pci_read32(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	if (unlikely(bus->mapped_device != dev)) {
+		if (unlikely(ssb_pci_switch_core(bus, dev)))
+			return 0xFFFFFFFF;
+	}
+	return readl(bus->mmio + offset);
+}
+
+static void ssb_pci_write16(struct ssb_device *dev, u16 offset, u16 value)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	if (unlikely(bus->mapped_device != dev)) {
+		if (unlikely(ssb_pci_switch_core(bus, dev)))
+			return;
+	}
+	writew(value, bus->mmio + offset);
+}
+
+static void ssb_pci_write32(struct ssb_device *dev, u16 offset, u32 value)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	if (unlikely(bus->mapped_device != dev)) {
+		if (unlikely(ssb_pci_switch_core(bus, dev)))
+			return;
+	}
+	writel(value, bus->mmio + offset);
+}
+
+/* Not "static", as it's used in main.c */
+const struct ssb_bus_ops ssb_pci_ops = {
+	.read16		= ssb_pci_read16,
+	.read32		= ssb_pci_read32,
+	.write16	= ssb_pci_write16,
+	.write32	= ssb_pci_write32,
+};
+
+static int sprom2hex(const u16 *sprom, char *buf, size_t buf_len)
+{
+	int i, pos = 0;
+
+	for (i = 0; i < SSB_SPROMSIZE_WORDS; i++) {
+		pos += snprintf(buf + pos, buf_len - pos - 1,
+				"%04X", swab16(sprom[i]) & 0xFFFF);
+	}
+	pos += snprintf(buf + pos, buf_len - pos - 1, "\n");
+
+	return pos + 1;
+}
+
+static int hex2sprom(u16 *sprom, const char *dump, size_t len)
+{
+	char tmp[5] = { 0 };
+	int cnt = 0;
+	unsigned long parsed;
+
+	if (len < SSB_SPROMSIZE_BYTES * 2)
+		return -EINVAL;
+
+	while (cnt < SSB_SPROMSIZE_WORDS) {
+		memcpy(tmp, dump, 4);
+		dump += 4;
+		parsed = simple_strtoul(tmp, NULL, 16);
+		sprom[cnt++] = swab16((u16)parsed);
+	}
+
+	return 0;
+}
+
+static ssize_t ssb_pci_attr_sprom_show(struct device *pcidev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	struct pci_dev *pdev = container_of(pcidev, struct pci_dev, dev);
+	struct ssb_bus *bus;
+	u16 *sprom;
+	int err = -ENODEV;
+	ssize_t count = 0;
+
+	bus = ssb_pci_dev_to_bus(pdev);
+	if (!bus)
+		goto out;
+	err = -ENOMEM;
+	sprom = kcalloc(SSB_SPROMSIZE_WORDS, sizeof(u16), GFP_KERNEL);
+	if (!sprom)
+		goto out;
+
+	/* Use interruptible locking, as the SPROM write might
+	 * be holding the lock for several seconds. So allow userspace
+	 * to cancel operation. */
+	err = -ERESTARTSYS;
+	if (mutex_lock_interruptible(&bus->pci_sprom_mutex))
+		goto out_kfree;
+	sprom_do_read(bus, sprom);
+	mutex_unlock(&bus->pci_sprom_mutex);
+
+	count = sprom2hex(sprom, buf, PAGE_SIZE);
+	err = 0;
+
+out_kfree:
+	kfree(sprom);
+out:
+	return err ? err : count;
+}
+
+static ssize_t ssb_pci_attr_sprom_store(struct device *pcidev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	struct pci_dev *pdev = container_of(pcidev, struct pci_dev, dev);
+	struct ssb_bus *bus;
+	u16 *sprom;
+	int res = 0, err = -ENODEV;
+
+	bus = ssb_pci_dev_to_bus(pdev);
+	if (!bus)
+		goto out;
+	err = -ENOMEM;
+	sprom = kcalloc(SSB_SPROMSIZE_WORDS, sizeof(u16), GFP_KERNEL);
+	if (!sprom)
+		goto out;
+	err = hex2sprom(sprom, buf, count);
+	if (err) {
+		err = -EINVAL;
+		goto out_kfree;
+	}
+	err = sprom_check_crc(sprom);
+	if (err) {
+		err = -EINVAL;
+		goto out_kfree;
+	}
+
+	/* Use interruptible locking, as the SPROM write might
+	 * be holding the lock for several seconds. So allow userspace
+	 * to cancel operation. */
+	err = -ERESTARTSYS;
+	if (mutex_lock_interruptible(&bus->pci_sprom_mutex))
+		goto out_kfree;
+	err = ssb_devices_freeze(bus);
+	if (err == -EOPNOTSUPP) {
+		ssb_printk(KERN_ERR PFX "SPROM write: Could not freeze devices. "
+			   "No suspend support. Is CONFIG_PM enabled?\n");
+		goto out_unlock;
+	}
+	if (err) {
+		ssb_printk(KERN_ERR PFX "SPROM write: Could not freeze all devices\n");
+		goto out_unlock;
+	}
+	res = sprom_do_write(bus, sprom);
+	err = ssb_devices_thaw(bus);
+	if (err)
+		ssb_printk(KERN_ERR PFX "SPROM write: Could not thaw all devices\n");
+out_unlock:
+	mutex_unlock(&bus->pci_sprom_mutex);
+out_kfree:
+	kfree(sprom);
+out:
+	if (res)
+		return res;
+	return err ? err : count;
+}
+
+static DEVICE_ATTR(ssb_sprom, 0600,
+		   ssb_pci_attr_sprom_show,
+		   ssb_pci_attr_sprom_store);
+
+void ssb_pci_exit(struct ssb_bus *bus)
+{
+	struct pci_dev *pdev;
+
+	if (bus->bustype != SSB_BUSTYPE_PCI)
+		return;
+
+	pdev = bus->host_pci;
+	device_remove_file(&pdev->dev, &dev_attr_ssb_sprom);
+}
+
+int ssb_pci_init(struct ssb_bus *bus)
+{
+	struct pci_dev *pdev;
+	int err;
+
+	if (bus->bustype != SSB_BUSTYPE_PCI)
+		return 0;
+
+	pdev = bus->host_pci;
+	mutex_init(&bus->pci_sprom_mutex);
+	err = device_create_file(&pdev->dev, &dev_attr_ssb_sprom);
+	if (err)
+		goto out;
+
+out:
+	return err;
+}
diff --git a/drivers/ssb/pcihost_wrapper.c b/drivers/ssb/pcihost_wrapper.c
new file mode 100644
index 0000000..82a10ab
--- /dev/null
+++ b/drivers/ssb/pcihost_wrapper.c
@@ -0,0 +1,104 @@
+/*
+ * Sonics Silicon Backplane
+ * PCI Hostdevice wrapper
+ *
+ * Copyright (c) 2005 Martin Langer <[email protected]>
+ * Copyright (c) 2005 Stefano Brivio <[email protected]>
+ * Copyright (c) 2005 Danny van Dyk <[email protected]>
+ * Copyright (c) 2005 Andreas Jaggi <[email protected]>
+ * Copyright (c) 2005-2007 Michael Buesch <[email protected]>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/pci.h>
+#include <linux/ssb/ssb.h>
+
+
+#ifdef CONFIG_PM
+static int ssb_pcihost_suspend(struct pci_dev *dev, pm_message_t state)
+{
+	pci_save_state(dev);
+	pci_disable_device(dev);
+	pci_set_power_state(dev, pci_choose_state(dev, state));
+
+	return 0;
+}
+
+static int ssb_pcihost_resume(struct pci_dev *dev)
+{
+	int err;
+
+	pci_set_power_state(dev, 0);
+	err = pci_enable_device(dev);
+	if (err)
+		return err;
+	pci_restore_state(dev);
+
+	return 0;
+}
+#else /* CONFIG_PM */
+# define ssb_pcihost_suspend	NULL
+# define ssb_pcihost_resume	NULL
+#endif /* CONFIG_PM */
+
+static int ssb_pcihost_probe(struct pci_dev *dev,
+			     const struct pci_device_id *id)
+{
+	struct ssb_bus *ssb;
+	int err = -ENOMEM;
+	const char *name;
+
+	ssb = kzalloc(sizeof(*ssb), GFP_KERNEL);
+	if (!ssb)
+		goto out;
+	err = pci_enable_device(dev);
+	if (err)
+		goto err_kfree_ssb;
+	name = dev->dev.bus_id;
+	if (dev->driver && dev->driver->name)
+		name = dev->driver->name;
+	err = pci_request_regions(dev, name);
+	if (err)
+		goto err_pci_disable;
+	pci_set_master(dev);
+
+	err = ssb_bus_pcibus_register(ssb, dev);
+	if (err)
+		goto err_pci_release_regions;
+
+	pci_set_drvdata(dev, ssb);
+
+out:
+	return err;
+
+err_pci_release_regions:
+	pci_release_regions(dev);
+err_pci_disable:
+	pci_disable_device(dev);
+err_kfree_ssb:
+	kfree(ssb);
+	return err;
+}
+
+static void ssb_pcihost_remove(struct pci_dev *dev)
+{
+	struct ssb_bus *ssb = pci_get_drvdata(dev);
+
+	ssb_bus_unregister(ssb);
+	pci_release_regions(dev);
+	pci_disable_device(dev);
+	kfree(ssb);
+	pci_set_drvdata(dev, NULL);
+}
+
+int ssb_pcihost_register(struct pci_driver *driver)
+{
+	driver->probe = ssb_pcihost_probe;
+	driver->remove = ssb_pcihost_remove;
+	driver->suspend = ssb_pcihost_suspend;
+	driver->resume = ssb_pcihost_resume;
+
+	return pci_register_driver(driver);
+}
+EXPORT_SYMBOL(ssb_pcihost_register);
diff --git a/drivers/ssb/pcmcia.c b/drivers/ssb/pcmcia.c
new file mode 100644
index 0000000..b102738
--- /dev/null
+++ b/drivers/ssb/pcmcia.c
@@ -0,0 +1,265 @@
+/*
+ * Sonics Silicon Backplane
+ * PCMCIA-Hostbus related functions
+ *
+ * Copyright 2006 Johannes Berg <[email protected]>
+ * Copyright 2007 Michael Buesch <[email protected]>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/ssb/ssb.h>
+#include <linux/delay.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ciscode.h>
+#include <pcmcia/ds.h>
+#include <pcmcia/cisreg.h>
+
+#include "ssb_private.h"
+
+
+int ssb_pcmcia_switch_coreidx(struct ssb_bus *bus,
+			      u8 coreidx)
+{
+	struct pcmcia_device *pdev = bus->host_pcmcia;
+	int err;
+	int attempts = 0;
+	u32 cur_core;
+	conf_reg_t reg;
+	u32 addr;
+	u32 read_addr;
+
+	addr = (coreidx * SSB_CORE_SIZE) + SSB_ENUM_BASE;
+	while (1) {
+		reg.Action = CS_WRITE;
+		reg.Offset = 0x2E;
+		reg.Value = (addr & 0x0000F000) >> 12;
+		err = pcmcia_access_configuration_register(pdev, &reg);
+		if (err != CS_SUCCESS)
+			goto error;
+		reg.Offset = 0x30;
+		reg.Value = (addr & 0x00FF0000) >> 16;
+		err = pcmcia_access_configuration_register(pdev, &reg);
+		if (err != CS_SUCCESS)
+			goto error;
+		reg.Offset = 0x32;
+		reg.Value = (addr & 0xFF000000) >> 24;
+		err = pcmcia_access_configuration_register(pdev, &reg);
+		if (err != CS_SUCCESS)
+			goto error;
+
+		read_addr = 0;
+
+		reg.Action = CS_READ;
+		reg.Offset = 0x2E;
+		err = pcmcia_access_configuration_register(pdev, &reg);
+		if (err != CS_SUCCESS)
+			goto error;
+		read_addr |= (reg.Value & 0xF) << 12;
+		reg.Offset = 0x30;
+		err = pcmcia_access_configuration_register(pdev, &reg);
+		if (err != CS_SUCCESS)
+			goto error;
+		read_addr |= reg.Value << 16;
+		reg.Offset = 0x32;
+		err = pcmcia_access_configuration_register(pdev, &reg);
+		if (err != CS_SUCCESS)
+			goto error;
+		read_addr |= reg.Value << 24;
+
+		cur_core = (read_addr - SSB_ENUM_BASE) / SSB_CORE_SIZE;
+		if (cur_core == coreidx)
+			break;
+
+		if (attempts++ > SSB_BAR0_MAX_RETRIES)
+			goto error;
+		udelay(10);
+	}
+
+	return 0;
+error:
+	ssb_printk(KERN_ERR PFX "Failed to switch to core %u\n", coreidx);
+	return -ENODEV;
+}
+
+int ssb_pcmcia_switch_core(struct ssb_bus *bus,
+			   struct ssb_device *dev)
+{
+	int err;
+	unsigned long flags;
+
+	ssb_dprintk(KERN_INFO PFX
+		    "Switching to %s core, index %d\n",
+		    ssb_core_name(dev->id.coreid),
+		    dev->core_index);
+
+	spin_lock_irqsave(&bus->bar_lock, flags);
+	err = ssb_pcmcia_switch_coreidx(bus, dev->core_index);
+	if (!err)
+		bus->mapped_device = dev;
+	spin_unlock_irqrestore(&bus->bar_lock, flags);
+
+	return err;
+}
+
+int ssb_pcmcia_switch_segment(struct ssb_bus *bus, u8 seg)
+{
+	int attempts = 0;
+	unsigned long flags;
+	conf_reg_t reg;
+	int res, err = 0;
+
+	SSB_WARN_ON((seg != 0) && (seg != 1));
+	reg.Offset = 0x34;
+	reg.Function = 0;
+	spin_lock_irqsave(&bus->bar_lock, flags);
+	while (1) {
+		reg.Action = CS_WRITE;
+		reg.Value = seg;
+		res = pcmcia_access_configuration_register(bus->host_pcmcia, &reg);
+		if (unlikely(res != CS_SUCCESS))
+			goto error;
+		reg.Value = 0xFF;
+		reg.Action = CS_READ;
+		res = pcmcia_access_configuration_register(bus->host_pcmcia, &reg);
+		if (unlikely(res != CS_SUCCESS))
+			goto error;
+
+		if (reg.Value == seg)
+			break;
+
+		if (unlikely(attempts++ > SSB_BAR0_MAX_RETRIES))
+			goto error;
+		udelay(10);
+	}
+	bus->mapped_pcmcia_seg = seg;
+out_unlock:
+	spin_unlock_irqrestore(&bus->bar_lock, flags);
+	return err;
+error:
+	ssb_printk(KERN_ERR PFX "Failed to switch pcmcia segment\n");
+	err = -ENODEV;
+	goto out_unlock;
+}
+
+/* These are the main device register access functions.
+ * do_select_core is inline to have the likely hotpath inline.
+ * All unlikely codepaths are out-of-line. */
+static inline int do_select_core(struct ssb_bus *bus,
+				 struct ssb_device *dev,
+				 u16 *offset)
+{
+	int err;
+	u8 need_seg = (*offset >= 0x800) ? 1 : 0;
+
+	if (unlikely(dev != bus->mapped_device)) {
+		err = ssb_pcmcia_switch_core(bus, dev);
+		if (unlikely(err))
+			return err;
+	}
+	if (unlikely(need_seg != bus->mapped_pcmcia_seg)) {
+		err = ssb_pcmcia_switch_segment(bus, need_seg);
+		if (unlikely(err))
+			return err;
+	}
+	if (need_seg == 1)
+		*offset -= 0x800;
+
+	return 0;
+}
+
+static u16 ssb_pcmcia_read16(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+	u16 x;
+
+	if (unlikely(do_select_core(bus, dev, &offset)))
+		return 0xFFFF;
+	x = readw(bus->mmio + offset);
+
+	return x;
+}
+
+static u32 ssb_pcmcia_read32(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+	u32 x;
+
+	if (unlikely(do_select_core(bus, dev, &offset)))
+		return 0xFFFFFFFF;
+	x = readl(bus->mmio + offset);
+
+	return x;
+}
+
+static void ssb_pcmcia_write16(struct ssb_device *dev, u16 offset, u16 value)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	if (unlikely(do_select_core(bus, dev, &offset)))
+		return;
+	writew(value, bus->mmio + offset);
+}
+
+static void ssb_pcmcia_write32(struct ssb_device *dev, u16 offset, u32 value)
+{
+	struct ssb_bus *bus = dev->bus;
+
+	if (unlikely(do_select_core(bus, dev, &offset)))
+		return;
+	readw(bus->mmio + offset);
+	writew(value >> 16, bus->mmio + offset + 2);
+	readw(bus->mmio + offset);
+	writew(value, bus->mmio + offset);
+}
+
+/* Not "static", as it's used in main.c */
+const struct ssb_bus_ops ssb_pcmcia_ops = {
+	.read16		= ssb_pcmcia_read16,
+	.read32		= ssb_pcmcia_read32,
+	.write16	= ssb_pcmcia_write16,
+	.write32	= ssb_pcmcia_write32,
+};
+
+int ssb_pcmcia_get_invariants(struct ssb_bus *bus,
+			      struct ssb_init_invariants *iv)
+{
+	//TODO
+	return 0;
+}
+
+int ssb_pcmcia_init(struct ssb_bus *bus)
+{
+	conf_reg_t reg;
+	int err;
+
+	if (bus->bustype != SSB_BUSTYPE_PCMCIA)
+		return 0;
+
+	/* Switch segment to a known state and sync
+	 * bus->mapped_pcmcia_seg with hardware state. */
+	ssb_pcmcia_switch_segment(bus, 0);
+
+	/* Init IRQ routing */
+	reg.Action = CS_READ;
+	reg.Function = 0;
+	if (bus->chip_id == 0x4306)
+		reg.Offset = 0x00;
+	else
+		reg.Offset = 0x80;
+	err = pcmcia_access_configuration_register(bus->host_pcmcia, &reg);
+	if (err != CS_SUCCESS)
+		goto error;
+	reg.Action = CS_WRITE;
+	reg.Value |= 0x04 | 0x01;
+	err = pcmcia_access_configuration_register(bus->host_pcmcia, &reg);
+	if (err != CS_SUCCESS)
+		goto error;
+
+	return 0;
+error:
+	return -ENODEV;
+}
diff --git a/drivers/ssb/scan.c b/drivers/ssb/scan.c
new file mode 100644
index 0000000..96258c6
--- /dev/null
+++ b/drivers/ssb/scan.c
@@ -0,0 +1,413 @@
+/*
+ * Sonics Silicon Backplane
+ * Bus scanning
+ *
+ * Copyright (C) 2005-2007 Michael Buesch <[email protected]>
+ * Copyright (C) 2005 Martin Langer <[email protected]>
+ * Copyright (C) 2005 Stefano Brivio <[email protected]>
+ * Copyright (C) 2005 Danny van Dyk <[email protected]>
+ * Copyright (C) 2005 Andreas Jaggi <[email protected]>
+ * Copyright (C) 2006 Broadcom Corporation.
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <linux/ssb/ssb.h>
+#include <linux/ssb/ssb_regs.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+
+#include "ssb_private.h"
+
+
+const char *ssb_core_name(u16 coreid)
+{
+	switch (coreid) {
+	case SSB_DEV_CHIPCOMMON:
+		return "ChipCommon";
+	case SSB_DEV_ILINE20:
+		return "ILine 20";
+	case SSB_DEV_SDRAM:
+		return "SDRAM";
+	case SSB_DEV_PCI:
+		return "PCI";
+	case SSB_DEV_MIPS:
+		return "MIPS";
+	case SSB_DEV_ETHERNET:
+		return "Fast Ethernet";
+	case SSB_DEV_V90:
+		return "V90";
+	case SSB_DEV_USB11_HOSTDEV:
+		return "USB 1.1 Hostdev";
+	case SSB_DEV_ADSL:
+		return "ADSL";
+	case SSB_DEV_ILINE100:
+		return "ILine 100";
+	case SSB_DEV_IPSEC:
+		return "IPSEC";
+	case SSB_DEV_PCMCIA:
+		return "PCMCIA";
+	case SSB_DEV_INTERNAL_MEM:
+		return "Internal Memory";
+	case SSB_DEV_MEMC_SDRAM:
+		return "MEMC SDRAM";
+	case SSB_DEV_EXTIF:
+		return "EXTIF";
+	case SSB_DEV_80211:
+		return "IEEE 802.11";
+	case SSB_DEV_MIPS_3302:
+		return "MIPS 3302";
+	case SSB_DEV_USB11_HOST:
+		return "USB 1.1 Host";
+	case SSB_DEV_USB11_DEV:
+		return "USB 1.1 Device";
+	case SSB_DEV_USB20_HOST:
+		return "USB 2.0 Host";
+	case SSB_DEV_USB20_DEV:
+		return "USB 2.0 Device";
+	case SSB_DEV_SDIO_HOST:
+		return "SDIO Host";
+	case SSB_DEV_ROBOSWITCH:
+		return "Roboswitch";
+	case SSB_DEV_PARA_ATA:
+		return "PATA";
+	case SSB_DEV_SATA_XORDMA:
+		return "SATA XOR-DMA";
+	case SSB_DEV_ETHERNET_GBIT:
+		return "GBit Ethernet";
+	case SSB_DEV_PCIE:
+		return "PCI-E";
+	case SSB_DEV_MIMO_PHY:
+		return "MIMO PHY";
+	case SSB_DEV_SRAM_CTRLR:
+		return "SRAM Controller";
+	case SSB_DEV_MINI_MACPHY:
+		return "Mini MACPHY";
+	case SSB_DEV_ARM_1176:
+		return "ARM 1176";
+	case SSB_DEV_ARM_7TDMI:
+		return "ARM 7TDMI";
+	}
+	return "UNKNOWN";
+}
+
+static u16 pcidev_to_chipid(struct pci_dev *pci_dev)
+{
+	u16 chipid_fallback = 0;
+
+	switch (pci_dev->device) {
+	case 0x4301:
+		chipid_fallback = 0x4301;
+		break;
+	case 0x4305 ... 0x4307:
+		chipid_fallback = 0x4307;
+		break;
+	case 0x4403:
+		chipid_fallback = 0x4402;
+		break;
+	case 0x4610 ... 0x4615:
+		chipid_fallback = 0x4610;
+		break;
+	case 0x4710 ... 0x4715:
+		chipid_fallback = 0x4710;
+		break;
+	case 0x4320 ... 0x4325:
+		chipid_fallback = 0x4309;
+		break;
+	case PCI_DEVICE_ID_BCM4401:
+	case PCI_DEVICE_ID_BCM4401B0:
+	case PCI_DEVICE_ID_BCM4401B1:
+		chipid_fallback = 0x4401;
+		break;
+	default:
+		ssb_printk(KERN_ERR PFX
+			   "PCI-ID not in fallback list\n");
+	}
+
+	return chipid_fallback;
+}
+
+static u8 chipid_to_nrcores(u16 chipid)
+{
+	switch (chipid) {
+	case 0x5365:
+		return 7;
+	case 0x4306:
+		return 6;
+	case 0x4310:
+		return 8;
+	case 0x4307:
+	case 0x4301:
+		return 5;
+	case 0x4401:
+	case 0x4402:
+		return 3;
+	case 0x4710:
+	case 0x4610:
+	case 0x4704:
+		return 9;
+	default:
+		ssb_printk(KERN_ERR PFX
+			   "CHIPID not in nrcores fallback list\n");
+	}
+
+	return 1;
+}
+
+static u32 scan_read32(struct ssb_bus *bus, u8 current_coreidx,
+		       u16 offset)
+{
+	switch (bus->bustype) {
+	case SSB_BUSTYPE_SSB:
+		offset += current_coreidx * SSB_CORE_SIZE;
+		break;
+	case SSB_BUSTYPE_PCI:
+		break;
+	case SSB_BUSTYPE_PCMCIA:
+		if (offset >= 0x800) {
+			ssb_pcmcia_switch_segment(bus, 1);
+			offset -= 0x800;
+		} else
+			ssb_pcmcia_switch_segment(bus, 0);
+		break;
+	}
+	return readl(bus->mmio + offset);
+}
+
+static int scan_switchcore(struct ssb_bus *bus, u8 coreidx)
+{
+	switch (bus->bustype) {
+	case SSB_BUSTYPE_SSB:
+		break;
+	case SSB_BUSTYPE_PCI:
+		return ssb_pci_switch_coreidx(bus, coreidx);
+	case SSB_BUSTYPE_PCMCIA:
+		return ssb_pcmcia_switch_coreidx(bus, coreidx);
+	}
+	return 0;
+}
+
+void ssb_iounmap(struct ssb_bus *bus)
+{
+	switch (bus->bustype) {
+	case SSB_BUSTYPE_SSB:
+	case SSB_BUSTYPE_PCMCIA:
+		iounmap(bus->mmio);
+		break;
+	case SSB_BUSTYPE_PCI:
+#ifdef CONFIG_SSB_PCIHOST
+		pci_iounmap(bus->host_pci, bus->mmio);
+#else
+		SSB_BUG_ON(1); /* Can't reach this code. */
+#endif
+		break;
+	}
+	bus->mmio = NULL;
+	bus->mapped_device = NULL;
+}
+
+static void __iomem *ssb_ioremap(struct ssb_bus *bus,
+				 unsigned long baseaddr)
+{
+	void __iomem *mmio = NULL;
+
+	switch (bus->bustype) {
+	case SSB_BUSTYPE_SSB:
+		/* Only map the first core for now. */
+		/* fallthrough... */
+	case SSB_BUSTYPE_PCMCIA:
+		mmio = ioremap(baseaddr, SSB_CORE_SIZE);
+		break;
+	case SSB_BUSTYPE_PCI:
+#ifdef CONFIG_SSB_PCIHOST
+		mmio = pci_iomap(bus->host_pci, 0, ~0UL);
+#else
+		SSB_BUG_ON(1); /* Can't reach this code. */
+#endif
+		break;
+	}
+
+	return mmio;
+}
+
+static int we_support_multiple_80211_cores(struct ssb_bus *bus)
+{
+	/* More than one 802.11 core is only supported by special chips.
+	 * There are chips with two 802.11 cores, but with dangling
+	 * pins on the second core. Be careful and reject them here.
+	 */
+
+#ifdef CONFIG_SSB_PCIHOST
+	if (bus->bustype == SSB_BUSTYPE_PCI) {
+		if (bus->host_pci->vendor == PCI_VENDOR_ID_BROADCOM &&
+		    bus->host_pci->device == 0x4324)
+			return 1;
+	}
+#endif /* CONFIG_SSB_PCIHOST */
+	return 0;
+}
+
+int ssb_bus_scan(struct ssb_bus *bus,
+		 unsigned long baseaddr)
+{
+	int err = -ENOMEM;
+	void __iomem *mmio;
+	u32 idhi, cc, rev, tmp;
+	int dev_i, i;
+	struct ssb_device *dev;
+	int nr_80211_cores = 0;
+
+	mmio = ssb_ioremap(bus, baseaddr);
+	if (!mmio)
+		goto out;
+	bus->mmio = mmio;
+
+	err = scan_switchcore(bus, 0); /* Switch to first core */
+	if (err)
+		goto err_unmap;
+
+	idhi = scan_read32(bus, 0, SSB_IDHIGH);
+	cc = (idhi & SSB_IDHIGH_CC) >> SSB_IDHIGH_CC_SHIFT;
+	rev = (idhi & SSB_IDHIGH_RCLO);
+	rev |= (idhi & SSB_IDHIGH_RCHI) >> SSB_IDHIGH_RCHI_SHIFT;
+
+	bus->nr_devices = 0;
+	if (cc == SSB_DEV_CHIPCOMMON) {
+		tmp = scan_read32(bus, 0, SSB_CHIPCO_CHIPID);
+
+		bus->chip_id = (tmp & SSB_CHIPCO_IDMASK);
+		bus->chip_rev = (tmp & SSB_CHIPCO_REVMASK) >>
+				SSB_CHIPCO_REVSHIFT;
+		bus->chip_package = (tmp & SSB_CHIPCO_PACKMASK) >>
+				    SSB_CHIPCO_PACKSHIFT;
+		if (rev >= 4) {
+			bus->nr_devices = (tmp & SSB_CHIPCO_NRCORESMASK) >>
+					  SSB_CHIPCO_NRCORESSHIFT;
+		}
+		tmp = scan_read32(bus, 0, SSB_CHIPCO_CAP);
+		bus->chipco.capabilities = tmp;
+	} else {
+		if (bus->bustype == SSB_BUSTYPE_PCI) {
+			bus->chip_id = pcidev_to_chipid(bus->host_pci);
+			pci_read_config_word(bus->host_pci, PCI_REVISION_ID,
+					     &bus->chip_rev);
+			bus->chip_package = 0;
+		} else {
+			bus->chip_id = 0x4710;
+			bus->chip_rev = 0;
+			bus->chip_package = 0;
+		}
+	}
+	if (!bus->nr_devices)
+		bus->nr_devices = chipid_to_nrcores(bus->chip_id);
+	if (bus->nr_devices > ARRAY_SIZE(bus->devices)) {
+		ssb_printk(KERN_ERR PFX
+			   "More than %d ssb cores found (%d)\n",
+			   SSB_MAX_NR_CORES, bus->nr_devices);
+		goto err_unmap;
+	}
+	if (bus->bustype == SSB_BUSTYPE_SSB) {
+		/* Now that we know the number of cores,
+		 * remap the whole IO space for all cores.
+		 */
+		err = -ENOMEM;
+		iounmap(mmio);
+		mmio = ioremap(baseaddr, SSB_CORE_SIZE * bus->nr_devices);
+		if (!mmio)
+			goto out;
+		bus->mmio = mmio;
+	}
+
+	/* Fetch basic information about each core/device */
+	for (i = 0, dev_i = 0; i < bus->nr_devices; i++) {
+		err = scan_switchcore(bus, i);
+		if (err)
+			goto err_unmap;
+		dev = &(bus->devices[dev_i]);
+
+		idhi = scan_read32(bus, i, SSB_IDHIGH);
+		dev->id.coreid = (idhi & SSB_IDHIGH_CC) >> SSB_IDHIGH_CC_SHIFT;
+		dev->id.revision = (idhi & SSB_IDHIGH_RCLO);
+		dev->id.revision |= (idhi & SSB_IDHIGH_RCHI) >> SSB_IDHIGH_RCHI_SHIFT;
+		dev->id.vendor = (idhi & SSB_IDHIGH_VC) >> SSB_IDHIGH_VC_SHIFT;
+		dev->core_index = i;
+		dev->bus = bus;
+		dev->ops = bus->ops;
+
+		ssb_dprintk(KERN_INFO PFX
+			    "Core %d found: %s "
+			    "(cc 0x%03X, rev 0x%02X, vendor 0x%04X)\n",
+			    i, ssb_core_name(dev->id.coreid),
+			    dev->id.coreid, dev->id.revision, dev->id.vendor);
+
+		switch (dev->id.coreid) {
+		case SSB_DEV_80211:
+			nr_80211_cores++;
+			if (nr_80211_cores > 1) {
+				if (!we_support_multiple_80211_cores(bus)) {
+					ssb_dprintk(KERN_INFO PFX "Ignoring additional "
+						    "802.11 core\n");
+					continue;
+				}
+			}
+			break;
+		case SSB_DEV_EXTIF:
+#ifdef CONFIG_SSB_DRIVER_EXTIF
+			if (bus->extif.dev) {
+				ssb_printk(KERN_WARNING PFX
+					   "WARNING: Multiple EXTIFs found\n");
+				break;
+			}
+			bus->extif.dev = dev;
+#endif /* CONFIG_SSB_DRIVER_EXTIF */
+			break;
+		case SSB_DEV_CHIPCOMMON:
+			if (bus->chipco.dev) {
+				ssb_printk(KERN_WARNING PFX
+					   "WARNING: Multiple ChipCommon found\n");
+				break;
+			}
+			bus->chipco.dev = dev;
+			break;
+		case SSB_DEV_MIPS:
+		case SSB_DEV_MIPS_3302:
+#ifdef CONFIG_SSB_DRIVER_MIPS
+			if (bus->mipscore.dev) {
+				ssb_printk(KERN_WARNING PFX
+					   "WARNING: Multiple MIPS cores found\n");
+				break;
+			}
+			bus->mipscore.dev = dev;
+#endif /* CONFIG_SSB_DRIVER_MIPS */
+			break;
+		case SSB_DEV_PCI:
+		case SSB_DEV_PCIE:
+#ifdef CONFIG_SSB_DRIVER_PCICORE
+			if (bus->pcicore.dev) {
+				ssb_printk(KERN_WARNING PFX
+					   "WARNING: Multiple PCI(E) cores found\n");
+				break;
+			}
+			bus->pcicore.dev = dev;
+#endif /* CONFIG_SSB_DRIVER_PCICORE */
+			break;
+		default:
+			break;
+		}
+
+		dev_i++;
+	}
+	bus->nr_devices = dev_i;
+
+	err = 0;
+out:
+	return err;
+err_unmap:
+	ssb_iounmap(bus);
+	goto out;
+}
diff --git a/drivers/ssb/ssb_private.h b/drivers/ssb/ssb_private.h
new file mode 100644
index 0000000..9ccb2d8
--- /dev/null
+++ b/drivers/ssb/ssb_private.h
@@ -0,0 +1,122 @@
+#ifndef LINUX_SSB_PRIVATE_H_
+#define LINUX_SSB_PRIVATE_H_
+
+#include <linux/ssb/ssb.h>
+#include <linux/types.h>
+
+
+#define PFX	"ssb: "
+
+#ifdef CONFIG_SSB_SILENT
+# define ssb_printk(fmt, x...)	do { /* nothing */ } while (0)
+#else
+# define ssb_printk		printk
+#endif /* CONFIG_SSB_SILENT */
+
+/* dprintk: Debugging printk; vanishes for non-debug compilation */
+#ifdef CONFIG_SSB_DEBUG
+# define ssb_dprintk(fmt, x...)	ssb_printk(fmt , ##x)
+#else
+# define ssb_dprintk(fmt, x...)	do { /* nothing */ } while (0)
+#endif
+
+#ifdef CONFIG_SSB_DEBUG
+# define SSB_WARN_ON(x)		WARN_ON(x)
+# define SSB_BUG_ON(x)		BUG_ON(x)
+#else
+static inline int __ssb_do_nothing(void) { return 0; }
+# define SSB_WARN_ON(x)		__ssb_do_nothing()
+# define SSB_BUG_ON(x)		__ssb_do_nothing()
+#endif
+
+
+/* pci.c */
+#ifdef CONFIG_SSB_PCIHOST
+extern int ssb_pci_switch_core(struct ssb_bus *bus,
+			       struct ssb_device *dev);
+extern int ssb_pci_switch_coreidx(struct ssb_bus *bus,
+				  u8 coreidx);
+extern int ssb_pci_xtal(struct ssb_bus *bus, u32 what,
+			int turn_on);
+extern int ssb_pci_get_invariants(struct ssb_bus *bus,
+				  struct ssb_init_invariants *iv);
+extern void ssb_pci_exit(struct ssb_bus *bus);
+extern int ssb_pci_init(struct ssb_bus *bus);
+extern const struct ssb_bus_ops ssb_pci_ops;
+
+#else /* CONFIG_SSB_PCIHOST */
+
+static inline int ssb_pci_switch_core(struct ssb_bus *bus,
+				      struct ssb_device *dev)
+{
+	return 0;
+}
+static inline int ssb_pci_switch_coreidx(struct ssb_bus *bus,
+					 u8 coreidx)
+{
+	return 0;
+}
+static inline int ssb_pci_xtal(struct ssb_bus *bus, u32 what,
+			       int turn_on)
+{
+	return 0;
+}
+static inline void ssb_pci_exit(struct ssb_bus *bus)
+{
+}
+static inline int ssb_pci_init(struct ssb_bus *bus)
+{
+	return 0;
+}
+#endif /* CONFIG_SSB_PCIHOST */
+
+
+/* pcmcia.c */
+#ifdef CONFIG_SSB_PCMCIAHOST
+extern int ssb_pcmcia_switch_core(struct ssb_bus *bus,
+				  struct ssb_device *dev);
+extern int ssb_pcmcia_switch_coreidx(struct ssb_bus *bus,
+				     u8 coreidx);
+extern int ssb_pcmcia_switch_segment(struct ssb_bus *bus,
+				     u8 seg);
+extern int ssb_pcmcia_get_invariants(struct ssb_bus *bus,
+				     struct ssb_init_invariants *iv);
+extern int ssb_pcmcia_init(struct ssb_bus *bus);
+extern const struct ssb_bus_ops ssb_pcmcia_ops;
+#else /* CONFIG_SSB_PCMCIAHOST */
+static inline int ssb_pcmcia_switch_core(struct ssb_bus *bus,
+					 struct ssb_device *dev)
+{
+	return 0;
+}
+static inline int ssb_pcmcia_switch_coreidx(struct ssb_bus *bus,
+					    u8 coreidx)
+{
+	return 0;
+}
+static inline int ssb_pcmcia_switch_segment(struct ssb_bus *bus,
+					    u8 seg)
+{
+	return 0;
+}
+static inline int ssb_pcmcia_init(struct ssb_bus *bus)
+{
+	return 0;
+}
+#endif /* CONFIG_SSB_PCMCIAHOST */
+
+
+/* scan.c */
+extern const char *ssb_core_name(u16 coreid);
+extern int ssb_bus_scan(struct ssb_bus *bus,
+			unsigned long baseaddr);
+extern void ssb_iounmap(struct ssb_bus *ssb);
+
+
+/* core.c */
+extern u32 ssb_calc_clock_rate(u32 plltype, u32 n, u32 m);
+extern int ssb_devices_freeze(struct ssb_bus *bus);
+extern int ssb_devices_thaw(struct ssb_bus *bus);
+extern struct ssb_bus *ssb_pci_dev_to_bus(struct pci_dev *pdev);
+
+#endif /* LINUX_SSB_PRIVATE_H_ */
diff --git a/include/linux/ssb/ssb_driver_chipcommon.h b/include/linux/ssb/ssb_driver_chipcommon.h
new file mode 100644
index 0000000..d58c24b
--- /dev/null
+++ b/include/linux/ssb/ssb_driver_chipcommon.h
@@ -0,0 +1,385 @@
+#ifndef LINUX_SSB_CHIPCO_H_
+#define LINUX_SSB_CHIPCO_H_
+
+/* SonicsSiliconBackplane CHIPCOMMON core hardware definitions
+ *
+ * The chipcommon core provides chip identification, SB control,
+ * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
+ * gpio interface, extbus, and support for serial and parallel flashes.
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, Michael Buesch <[email protected]>
+ *
+ * Licensed under the GPL version 2. See COPYING for details.
+ */
+
+/** ChipCommon core registers. **/
+
+#define SSB_CHIPCO_CHIPID		0x0000
+#define  SSB_CHIPCO_IDMASK		0x0000FFFF
+#define  SSB_CHIPCO_REVMASK		0x000F0000
+#define  SSB_CHIPCO_REVSHIFT		16
+#define  SSB_CHIPCO_PACKMASK		0x00F00000
+#define  SSB_CHIPCO_PACKSHIFT		20
+#define  SSB_CHIPCO_NRCORESMASK		0x0F000000
+#define  SSB_CHIPCO_NRCORESSHIFT	24
+#define SSB_CHIPCO_CAP	 		0x0004		/* Capabilities */
+#define  SSB_CHIPCO_CAP_NRUART		0x00000003	/* # of UARTs */
+#define  SSB_CHIPCO_CAP_MIPSEB		0x00000004	/* MIPS in BigEndian Mode */
+#define  SSB_CHIPCO_CAP_UARTCLK		0x00000018	/* UART clock select */
+#define   SSB_CHIPCO_CAP_UARTCLK_INT	0x00000008	/* UARTs are driven by internal divided clock */
+#define  SSB_CHIPCO_CAP_UARTGPIO	0x00000020	/* UARTs on GPIO 15-12 */
+#define  SSB_CHIPCO_CAP_EXTBUS		0x000000C0	/* External buses present */
+#define  SSB_CHIPCO_CAP_FLASHT		0x00000700	/* Flash Type */
+#define   SSB_CHIPCO_FLASHT_NONE	0x00000000	/* No flash */
+#define   SSB_CHIPCO_FLASHT_STSER	0x00000100	/* ST serial flash */
+#define   SSB_CHIPCO_FLASHT_ATSER	0x00000200	/* Atmel serial flash */
+#define	  SSB_CHIPCO_FLASHT_PARA	0x00000700	/* Parallel flash */
+#define  SSB_CHIPCO_CAP_PLLT		0x00038000	/* PLL Type */
+#define   SSB_PLLTYPE_NONE		0x00000000
+#define   SSB_PLLTYPE_1			0x00010000	/* 48Mhz base, 3 dividers */
+#define   SSB_PLLTYPE_2			0x00020000	/* 48Mhz, 4 dividers */
+#define   SSB_PLLTYPE_3			0x00030000	/* 25Mhz, 2 dividers */
+#define   SSB_PLLTYPE_4			0x00008000	/* 48Mhz, 4 dividers */
+#define   SSB_PLLTYPE_5			0x00018000	/* 25Mhz, 4 dividers */
+#define   SSB_PLLTYPE_6			0x00028000	/* 100/200 or 120/240 only */
+#define   SSB_PLLTYPE_7			0x00038000	/* 25Mhz, 4 dividers */
+#define  SSB_CHIPCO_CAP_PCTL		0x00040000	/* Power Control */
+#define  SSB_CHIPCO_CAP_OTPS		0x00380000	/* OTP size */
+#define  SSB_CHIPCO_CAP_OTPS_SHIFT	19
+#define  SSB_CHIPCO_CAP_OTPS_BASE	5
+#define  SSB_CHIPCO_CAP_JTAGM		0x00400000	/* JTAG master present */
+#define  SSB_CHIPCO_CAP_BROM		0x00800000	/* Internal boot ROM active */
+#define  SSB_CHIPCO_CAP_64BIT		0x08000000	/* 64-bit Backplane */
+#define SSB_CHIPCO_CORECTL		0x0008
+#define  SSB_CHIPCO_CORECTL_UARTCLK0	0x00000001	/* Drive UART with internal clock */
+#define	 SSB_CHIPCO_CORECTL_SE		0x00000002	/* sync clk out enable (corerev >= 3) */
+#define SSB_CHIPCO_BIST			0x000C
+#define SSB_CHIPCO_OTPS			0x0010		/* OTP status */
+#define	 SSB_CHIPCO_OTPS_PROGFAIL	0x80000000
+#define	 SSB_CHIPCO_OTPS_PROTECT	0x00000007
+#define	 SSB_CHIPCO_OTPS_HW_PROTECT	0x00000001
+#define	 SSB_CHIPCO_OTPS_SW_PROTECT	0x00000002
+#define	 SSB_CHIPCO_OTPS_CID_PROTECT	0x00000004
+#define SSB_CHIPCO_OTPC			0x0014		/* OTP control */
+#define	 SSB_CHIPCO_OTPC_RECWAIT	0xFF000000
+#define	 SSB_CHIPCO_OTPC_PROGWAIT	0x00FFFF00
+#define	 SSB_CHIPCO_OTPC_PRW_SHIFT	8
+#define	 SSB_CHIPCO_OTPC_MAXFAIL	0x00000038
+#define	 SSB_CHIPCO_OTPC_VSEL		0x00000006
+#define	 SSB_CHIPCO_OTPC_SELVL		0x00000001
+#define SSB_CHIPCO_OTPP			0x0018		/* OTP prog */
+#define	 SSB_CHIPCO_OTPP_COL		0x000000FF
+#define	 SSB_CHIPCO_OTPP_ROW		0x0000FF00
+#define	 SSB_CHIPCO_OTPP_ROW_SHIFT	8
+#define	 SSB_CHIPCO_OTPP_READERR	0x10000000
+#define	 SSB_CHIPCO_OTPP_VALUE		0x20000000
+#define	 SSB_CHIPCO_OTPP_READ		0x40000000
+#define	 SSB_CHIPCO_OTPP_START		0x80000000
+#define	 SSB_CHIPCO_OTPP_BUSY		0x80000000
+#define SSB_CHIPCO_IRQSTAT		0x0020
+#define SSB_CHIPCO_IRQMASK		0x0024
+#define	 SSB_CHIPCO_IRQ_GPIO		0x00000001	/* gpio intr */
+#define	 SSB_CHIPCO_IRQ_EXT		0x00000002	/* ro: ext intr pin (corerev >= 3) */
+#define	 SSB_CHIPCO_IRQ_WDRESET		0x80000000	/* watchdog reset occurred */
+#define SSB_CHIPCO_CHIPCTL		0x0028		/* Rev >= 11 only */
+#define SSB_CHIPCO_CHIPSTAT		0x002C		/* Rev >= 11 only */
+#define SSB_CHIPCO_JCMD			0x0030		/* Rev >= 10 only */
+#define  SSB_CHIPCO_JCMD_START		0x80000000
+#define  SSB_CHIPCO_JCMD_BUSY		0x80000000
+#define  SSB_CHIPCO_JCMD_PAUSE		0x40000000
+#define  SSB_CHIPCO_JCMD0_ACC_MASK	0x0000F000
+#define  SSB_CHIPCO_JCMD0_ACC_IRDR	0x00000000
+#define  SSB_CHIPCO_JCMD0_ACC_DR	0x00001000
+#define  SSB_CHIPCO_JCMD0_ACC_IR	0x00002000
+#define  SSB_CHIPCO_JCMD0_ACC_RESET	0x00003000
+#define  SSB_CHIPCO_JCMD0_ACC_IRPDR	0x00004000
+#define  SSB_CHIPCO_JCMD0_ACC_PDR	0x00005000
+#define  SSB_CHIPCO_JCMD0_IRW_MASK	0x00000F00
+#define  SSB_CHIPCO_JCMD_ACC_MASK	0x000F0000	/* Changes for corerev 11 */
+#define  SSB_CHIPCO_JCMD_ACC_IRDR	0x00000000
+#define  SSB_CHIPCO_JCMD_ACC_DR		0x00010000
+#define  SSB_CHIPCO_JCMD_ACC_IR		0x00020000
+#define  SSB_CHIPCO_JCMD_ACC_RESET	0x00030000
+#define  SSB_CHIPCO_JCMD_ACC_IRPDR	0x00040000
+#define  SSB_CHIPCO_JCMD_ACC_PDR	0x00050000
+#define  SSB_CHIPCO_JCMD_IRW_MASK	0x00001F00
+#define  SSB_CHIPCO_JCMD_IRW_SHIFT	8
+#define  SSB_CHIPCO_JCMD_DRW_MASK	0x0000003F
+#define SSB_CHIPCO_JIR			0x0034		/* Rev >= 10 only */
+#define SSB_CHIPCO_JDR			0x0038		/* Rev >= 10 only */
+#define SSB_CHIPCO_JCTL			0x003C		/* Rev >= 10 only */
+#define  SSB_CHIPCO_JCTL_FORCE_CLK	4		/* Force clock */
+#define  SSB_CHIPCO_JCTL_EXT_EN		2		/* Enable external targets */
+#define  SSB_CHIPCO_JCTL_EN		1		/* Enable Jtag master */
+#define SSB_CHIPCO_FLASHCTL		0x0040
+#define  SSB_CHIPCO_FLASHCTL_START	0x80000000
+#define  SSB_CHIPCO_FLASHCTL_BUSY	SSB_CHIPCO_FLASHCTL_START
+#define SSB_CHIPCO_FLASHADDR		0x0044
+#define SSB_CHIPCO_FLASHDATA		0x0048
+#define SSB_CHIPCO_BCAST_ADDR		0x0050
+#define SSB_CHIPCO_BCAST_DATA		0x0054
+#define SSB_CHIPCO_GPIOIN		0x0060
+#define SSB_CHIPCO_GPIOOUT		0x0064
+#define SSB_CHIPCO_GPIOOUTEN		0x0068
+#define SSB_CHIPCO_GPIOCTL		0x006C
+#define SSB_CHIPCO_GPIOPOL		0x0070
+#define SSB_CHIPCO_GPIOIRQ		0x0074
+#define SSB_CHIPCO_WATCHDOG		0x0080
+#define SSB_CHIPCO_GPIOTIMER		0x0088		/* LED powersave (corerev >= 16) */
+#define  SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT	16
+#define SSB_CHIPCO_GPIOTOUTM		0x008C		/* LED powersave (corerev >= 16) */
+#define SSB_CHIPCO_CLOCK_N		0x0090
+#define SSB_CHIPCO_CLOCK_SB		0x0094
+#define SSB_CHIPCO_CLOCK_PCI		0x0098
+#define SSB_CHIPCO_CLOCK_M2		0x009C
+#define SSB_CHIPCO_CLOCK_MIPS		0x00A0
+#define SSB_CHIPCO_CLKDIV		0x00A4		/* Rev >= 3 only */
+#define	 SSB_CHIPCO_CLKDIV_SFLASH	0x0F000000
+#define	 SSB_CHIPCO_CLKDIV_SFLASH_SHIFT	24
+#define	 SSB_CHIPCO_CLKDIV_OTP		0x000F0000
+#define	 SSB_CHIPCO_CLKDIV_OTP_SHIFT	16
+#define	 SSB_CHIPCO_CLKDIV_JTAG		0x00000F00
+#define	 SSB_CHIPCO_CLKDIV_JTAG_SHIFT	8
+#define	 SSB_CHIPCO_CLKDIV_UART		0x000000FF
+#define SSB_CHIPCO_PLLONDELAY		0x00B0		/* Rev >= 4 only */
+#define SSB_CHIPCO_FREFSELDELAY		0x00B4		/* Rev >= 4 only */
+#define SSB_CHIPCO_SLOWCLKCTL		0x00B8		/* 6 <= Rev <= 9 only */
+#define  SSB_CHIPCO_SLOWCLKCTL_SRC	0x00000007	/* slow clock source mask */
+#define	  SSB_CHIPCO_SLOWCLKCTL_SRC_LPO		0x00000000	/* source of slow clock is LPO */
+#define   SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL	0x00000001	/* source of slow clock is crystal */
+#define	  SSB_CHIPCO_SLOECLKCTL_SRC_PCI		0x00000002	/* source of slow clock is PCI */
+#define  SSB_CHIPCO_SLOWCLKCTL_LPOFREQ	0x00000200	/* LPOFreqSel, 1: 160Khz, 0: 32KHz */
+#define  SSB_CHIPCO_SLOWCLKCTL_LPOPD	0x00000400	/* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */
+#define  SSB_CHIPCO_SLOWCLKCTL_FSLOW	0x00000800	/* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */
+#define  SSB_CHIPCO_SLOWCLKCTL_IPLL	0x00001000	/* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */
+#define  SSB_CHIPCO_SLOWCLKCTL_ENXTAL	0x00002000	/* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */
+#define  SSB_CHIPCO_SLOWCLKCTL_XTALPU	0x00004000	/* XtalPU (RO), 1/0: crystal running/disabled */
+#define  SSB_CHIPCO_SLOWCLKCTL_CLKDIV	0xFFFF0000	/* ClockDivider (SlowClk = 1/(4+divisor)) */
+#define  SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT	16
+#define SSB_CHIPCO_SYSCLKCTL		0x00C0		/* Rev >= 3 only */
+#define	 SSB_CHIPCO_SYSCLKCTL_IDLPEN	0x00000001	/* ILPen: Enable Idle Low Power */
+#define	 SSB_CHIPCO_SYSCLKCTL_ALPEN	0x00000002	/* ALPen: Enable Active Low Power */
+#define	 SSB_CHIPCO_SYSCLKCTL_PLLEN	0x00000004	/* ForcePLLOn */
+#define	 SSB_CHIPCO_SYSCLKCTL_FORCEALP	0x00000008	/* Force ALP (or HT if ALPen is not set */
+#define	 SSB_CHIPCO_SYSCLKCTL_FORCEHT	0x00000010	/* Force HT */
+#define  SSB_CHIPCO_SYSCLKCTL_CLKDIV	0xFFFF0000	/* ClkDiv  (ILP = 1/(4+divisor)) */
+#define  SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT	16
+#define SSB_CHIPCO_CLKSTSTR		0x00C4		/* Rev >= 3 only */
+#define SSB_CHIPCO_PCMCIA_CFG		0x0100
+#define SSB_CHIPCO_PCMCIA_MEMWAIT	0x0104
+#define SSB_CHIPCO_PCMCIA_ATTRWAIT	0x0108
+#define SSB_CHIPCO_PCMCIA_IOWAIT	0x010C
+#define SSB_CHIPCO_IDE_CFG		0x0110
+#define SSB_CHIPCO_IDE_MEMWAIT		0x0114
+#define SSB_CHIPCO_IDE_ATTRWAIT		0x0118
+#define SSB_CHIPCO_IDE_IOWAIT		0x011C
+#define SSB_CHIPCO_PROG_CFG		0x0120
+#define SSB_CHIPCO_PROG_WAITCNT		0x0124
+#define SSB_CHIPCO_FLASH_CFG		0x0128
+#define SSB_CHIPCO_FLASH_WAITCNT	0x012C
+#define SSB_CHIPCO_UART0_DATA		0x0300
+#define SSB_CHIPCO_UART0_IMR		0x0304
+#define SSB_CHIPCO_UART0_FCR		0x0308
+#define SSB_CHIPCO_UART0_LCR		0x030C
+#define SSB_CHIPCO_UART0_MCR		0x0310
+#define SSB_CHIPCO_UART0_LSR		0x0314
+#define SSB_CHIPCO_UART0_MSR		0x0318
+#define SSB_CHIPCO_UART0_SCRATCH	0x031C
+#define SSB_CHIPCO_UART1_DATA		0x0400
+#define SSB_CHIPCO_UART1_IMR		0x0404
+#define SSB_CHIPCO_UART1_FCR		0x0408
+#define SSB_CHIPCO_UART1_LCR		0x040C
+#define SSB_CHIPCO_UART1_MCR		0x0410
+#define SSB_CHIPCO_UART1_LSR		0x0414
+#define SSB_CHIPCO_UART1_MSR		0x0418
+#define SSB_CHIPCO_UART1_SCRATCH	0x041C
+
+
+
+/** Clockcontrol masks and values **/
+
+/* SSB_CHIPCO_CLOCK_N */
+#define	SSB_CHIPCO_CLK_N1		0x0000003F	/* n1 control */
+#define	SSB_CHIPCO_CLK_N2		0x00003F00	/* n2 control */
+#define	SSB_CHIPCO_CLK_N2_SHIFT		8
+#define	SSB_CHIPCO_CLK_PLLC		0x000F0000	/* pll control */
+#define	SSB_CHIPCO_CLK_PLLC_SHIFT	16
+
+/* SSB_CHIPCO_CLOCK_SB/PCI/UART */
+#define	SSB_CHIPCO_CLK_M1		0x0000003F	/* m1 control */
+#define	SSB_CHIPCO_CLK_M2		0x00003F00	/* m2 control */
+#define	SSB_CHIPCO_CLK_M2_SHIFT		8
+#define	SSB_CHIPCO_CLK_M3		0x003F0000	/* m3 control */
+#define	SSB_CHIPCO_CLK_M3_SHIFT		16
+#define	SSB_CHIPCO_CLK_MC		0x1F000000	/* mux control */
+#define	SSB_CHIPCO_CLK_MC_SHIFT		24
+
+/* N3M Clock control magic field values */
+#define	SSB_CHIPCO_CLK_F6_2		0x02		/* A factor of 2 in */
+#define	SSB_CHIPCO_CLK_F6_3		0x03		/* 6-bit fields like */
+#define	SSB_CHIPCO_CLK_F6_4		0x05		/* N1, M1 or M3 */
+#define	SSB_CHIPCO_CLK_F6_5		0x09
+#define	SSB_CHIPCO_CLK_F6_6		0x11
+#define	SSB_CHIPCO_CLK_F6_7		0x21
+
+#define	SSB_CHIPCO_CLK_F5_BIAS		5		/* 5-bit fields get this added */
+
+#define	SSB_CHIPCO_CLK_MC_BYPASS	0x08
+#define	SSB_CHIPCO_CLK_MC_M1		0x04
+#define	SSB_CHIPCO_CLK_MC_M1M2		0x02
+#define	SSB_CHIPCO_CLK_MC_M1M2M3	0x01
+#define	SSB_CHIPCO_CLK_MC_M1M3		0x11
+
+/* Type 2 Clock control magic field values */
+#define	SSB_CHIPCO_CLK_T2_BIAS		2		/* n1, n2, m1 & m3 bias */
+#define	SSB_CHIPCO_CLK_T2M2_BIAS	3		/* m2 bias */
+
+#define	SSB_CHIPCO_CLK_T2MC_M1BYP	1
+#define	SSB_CHIPCO_CLK_T2MC_M2BYP	2
+#define	SSB_CHIPCO_CLK_T2MC_M3BYP	4
+
+/* Type 6 Clock control magic field values */
+#define	SSB_CHIPCO_CLK_T6_MMASK		1		/* bits of interest in m */
+#define	SSB_CHIPCO_CLK_T6_M0		120000000	/* sb clock for m = 0 */
+#define	SSB_CHIPCO_CLK_T6_M1		100000000	/* sb clock for m = 1 */
+#define	SSB_CHIPCO_CLK_SB2MIPS_T6(sb)	(2 * (sb))
+
+/* Common clock base */
+#define	SSB_CHIPCO_CLK_BASE1		24000000	/* Half the clock freq */
+#define SSB_CHIPCO_CLK_BASE2		12500000	/* Alternate crystal on some PLL's */
+
+/* Clock control values for 200Mhz in 5350 */
+#define	SSB_CHIPCO_CLK_5350_N		0x0311
+#define	SSB_CHIPCO_CLK_5350_M		0x04020009
+
+
+/** Bits in the config registers **/
+
+#define	SSB_CHIPCO_CFG_EN		0x0001		/* Enable */
+#define	SSB_CHIPCO_CFG_EXTM		0x000E		/* Extif Mode */
+#define	 SSB_CHIPCO_CFG_EXTM_ASYNC	0x0002		/* Async/Parallel flash */
+#define	 SSB_CHIPCO_CFG_EXTM_SYNC	0x0004		/* Synchronous */
+#define	 SSB_CHIPCO_CFG_EXTM_PCMCIA	0x0008		/* PCMCIA */
+#define	 SSB_CHIPCO_CFG_EXTM_IDE	0x000A		/* IDE */
+#define	SSB_CHIPCO_CFG_DS16		0x0010		/* Data size, 0=8bit, 1=16bit */
+#define	SSB_CHIPCO_CFG_CLKDIV		0x0060		/* Sync: Clock divisor */
+#define	SSB_CHIPCO_CFG_CLKEN		0x0080		/* Sync: Clock enable */
+#define	SSB_CHIPCO_CFG_BSTRO		0x0100		/* Sync: Size/Bytestrobe */
+
+
+/** Flash-specific control/status values */
+
+/* flashcontrol opcodes for ST flashes */
+#define SSB_CHIPCO_FLASHCTL_ST_WREN	0x0006		/* Write Enable */
+#define SSB_CHIPCO_FLASHCTL_ST_WRDIS	0x0004		/* Write Disable */
+#define SSB_CHIPCO_FLASHCTL_ST_RDSR	0x0105		/* Read Status Register */
+#define SSB_CHIPCO_FLASHCTL_ST_WRSR	0x0101		/* Write Status Register */
+#define SSB_CHIPCO_FLASHCTL_ST_READ	0x0303		/* Read Data Bytes */
+#define SSB_CHIPCO_FLASHCTL_ST_PP	0x0302		/* Page Program */
+#define SSB_CHIPCO_FLASHCTL_ST_SE	0x02D8		/* Sector Erase */
+#define SSB_CHIPCO_FLASHCTL_ST_BE	0x00C7		/* Bulk Erase */
+#define SSB_CHIPCO_FLASHCTL_ST_DP	0x00B9		/* Deep Power-down */
+#define SSB_CHIPCO_FLASHCTL_ST_RSIG	0x03AB		/* Read Electronic Signature */
+
+/* Status register bits for ST flashes */
+#define SSB_CHIPCO_FLASHSTA_ST_WIP	0x01		/* Write In Progress */
+#define SSB_CHIPCO_FLASHSTA_ST_WEL	0x02		/* Write Enable Latch */
+#define SSB_CHIPCO_FLASHSTA_ST_BP	0x1C		/* Block Protect */
+#define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT	2
+#define SSB_CHIPCO_FLASHSTA_ST_SRWD	0x80		/* Status Register Write Disable */
+
+/* flashcontrol opcodes for Atmel flashes */
+#define SSB_CHIPCO_FLASHCTL_AT_READ		0x07E8
+#define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ	0x07D2
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ	/* FIXME */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ	/* FIXME */
+#define SSB_CHIPCO_FLASHCTL_AT_STATUS		0x01D7
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE	0x0384
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE	0x0387
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM	0x0283	/* Erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM	0x0286	/* Erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM	0x0288
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM	0x0289
+#define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE	0x0281
+#define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE	0x0250
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM	0x0382	/* Write erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM	0x0385	/* Write erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD	0x0253
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD	0x0255
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE	0x0260
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE	0x0261
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM	0x0258
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM	0x0259
+
+/* Status register bits for Atmel flashes */
+#define SSB_CHIPCO_FLASHSTA_AT_READY	0x80
+#define SSB_CHIPCO_FLASHSTA_AT_MISMATCH	0x40
+#define SSB_CHIPCO_FLASHSTA_AT_ID	0x38
+#define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT	3
+
+
+/** OTP **/
+
+/* OTP regions */
+#define	SSB_CHIPCO_OTP_HW_REGION	SSB_CHIPCO_OTPS_HW_PROTECT
+#define	SSB_CHIPCO_OTP_SW_REGION	SSB_CHIPCO_OTPS_SW_PROTECT
+#define	SSB_CHIPCO_OTP_CID_REGION	SSB_CHIPCO_OTPS_CID_PROTECT
+
+/* OTP regions (Byte offsets from otp size) */
+#define	SSB_CHIPCO_OTP_SWLIM_OFF	(-8)
+#define	SSB_CHIPCO_OTP_CIDBASE_OFF	0
+#define	SSB_CHIPCO_OTP_CIDLIM_OFF	8
+
+/* Predefined OTP words (Word offset from otp size) */
+#define	SSB_CHIPCO_OTP_BOUNDARY_OFF	(-4)
+#define	SSB_CHIPCO_OTP_HWSIGN_OFF	(-3)
+#define	SSB_CHIPCO_OTP_SWSIGN_OFF	(-2)
+#define	SSB_CHIPCO_OTP_CIDSIGN_OFF	(-1)
+
+#define	SSB_CHIPCO_OTP_CID_OFF		0
+#define	SSB_CHIPCO_OTP_PKG_OFF		1
+#define	SSB_CHIPCO_OTP_FID_OFF		2
+#define	SSB_CHIPCO_OTP_RSV_OFF		3
+#define	SSB_CHIPCO_OTP_LIM_OFF		4
+
+#define	SSB_CHIPCO_OTP_SIGNATURE	0x578A
+#define	SSB_CHIPCO_OTP_MAGIC		0x4E56
+
+
+struct ssb_device;
+struct ssb_serial_port;
+
+struct ssb_chipcommon {
+	struct ssb_device *dev;
+	u32 capabilities;
+	/* Fast Powerup Delay constant */
+	u16 fast_pwrup_delay;
+};
+
+extern void ssb_chipcommon_init(struct ssb_chipcommon *cc);
+
+#include <linux/pm.h>
+extern void ssb_chipco_suspend(struct ssb_chipcommon *cc, pm_message_t state);
+extern void ssb_chipco_resume(struct ssb_chipcommon *cc);
+
+extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
+					u32 *plltype, u32 *n, u32 *m);
+extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
+				   unsigned long ns_per_cycle);
+
+enum ssb_clkmode {
+	SSB_CLKMODE_SLOW,
+	SSB_CLKMODE_FAST,
+	SSB_CLKMODE_DYNAMIC,
+};
+
+extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
+				     enum ssb_clkmode mode);
+
+#ifdef CONFIG_SSB_SERIAL
+extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
+				  struct ssb_serial_port *ports);
+#endif /* CONFIG_SSB_SERIAL */
+
+#endif /* LINUX_SSB_CHIPCO_H_ */
diff --git a/include/linux/ssb/ssb_driver_extif.h b/include/linux/ssb/ssb_driver_extif.h
new file mode 100644
index 0000000..00de749
--- /dev/null
+++ b/include/linux/ssb/ssb_driver_extif.h
@@ -0,0 +1,160 @@
+/*
+ * Hardware-specific External Interface I/O core definitions
+ * for the BCM47xx family of SiliconBackplane-based chips.
+ *
+ * The External Interface core supports a total of three external chip selects
+ * supporting external interfaces. One of the external chip selects is
+ * used for Flash, one is used for PCMCIA, and the other may be
+ * programmed to support either a synchronous interface or an
+ * asynchronous interface. The asynchronous interface can be used to
+ * support external devices such as UARTs and the BCM2019 Bluetooth
+ * baseband processor.
+ * The external interface core also contains 2 on-chip 16550 UARTs, clock
+ * frequency control, a watchdog interrupt timer, and a GPIO interface.
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, Michael Buesch
+ *
+ * Licensed under the GPL version 2. See COPYING for details.
+ */
+#ifndef LINUX_SSB_EXTIFCORE_H_
+#define LINUX_SSB_EXTIFCORE_H_
+
+struct ssb_extif {
+	struct ssb_device *dev;
+};
+
+/* external interface address space */
+#define	SSB_EXTIF_PCMCIA_MEMBASE(x)	(x)
+#define	SSB_EXTIF_PCMCIA_IOBASE(x)	((x) + 0x100000)
+#define	SSB_EXTIF_PCMCIA_CFGBASE(x)	((x) + 0x200000)
+#define	SSB_EXTIF_CFGIF_BASE(x)		((x) + 0x800000)
+#define	SSB_EXTIF_FLASH_BASE(x)		((x) + 0xc00000)
+
+#define SSB_EXTIF_NR_GPIOOUT		5
+/* GPIO NOTE:
+ * The multiple instances of output and output enable registers
+ * are present to allow driver software for multiple cores to control
+ * gpio outputs without needing to share a single register pair.
+ * Use the following helper macro to get a register offset value.
+ */
+#define SSB_EXTIF_GPIO_OUT(index)	({		\
+	BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT);	\
+	SSB_EXTIF_GPIO_OUT_BASE + ((index) * 8);	\
+					})
+#define SSB_EXTIF_GPIO_OUTEN(index)	({		\
+	BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT);	\
+	SSB_EXTIF_GPIO_OUTEN_BASE + ((index) * 8);	\
+					})
+
+/** EXTIF core registers **/
+
+#define SSB_EXTIF_CTL			0x0000
+#define  SSB_EXTIF_CTL_UARTEN		(1 << 0) /* UART enable */
+#define SSB_EXTIF_EXTSTAT		0x0004
+#define  SSB_EXTIF_EXTSTAT_EMODE	(1 << 0) /* Endian mode (ro) */
+#define  SSB_EXTIF_EXTSTAT_EIRQPIN	(1 << 1) /* External interrupt pin (ro) */
+#define  SSB_EXTIF_EXTSTAT_GPIOIRQPIN	(1 << 2) /* GPIO interrupt pin (ro) */
+#define SSB_EXTIF_PCMCIA_CFG		0x0010
+#define SSB_EXTIF_PCMCIA_MEMWAIT	0x0014
+#define SSB_EXTIF_PCMCIA_ATTRWAIT	0x0018
+#define SSB_EXTIF_PCMCIA_IOWAIT		0x001C
+#define SSB_EXTIF_PROG_CFG		0x0020
+#define SSB_EXTIF_PROG_WAITCNT		0x0024
+#define SSB_EXTIF_FLASH_CFG		0x0028
+#define SSB_EXTIF_FLASH_WAITCNT		0x002C
+#define SSB_EXTIF_WATCHDOG		0x0040
+#define SSB_EXTIF_CLOCK_N		0x0044
+#define SSB_EXTIF_CLOCK_SB		0x0048
+#define SSB_EXTIF_CLOCK_PCI		0x004C
+#define SSB_EXTIF_CLOCK_MII		0x0050
+#define SSB_EXTIF_GPIO_IN		0x0060
+#define SSB_EXTIF_GPIO_OUT_BASE		0x0064
+#define SSB_EXTIF_GPIO_OUTEN_BASE	0x0068
+#define SSB_EXTIF_EJTAG_OUTEN		0x0090
+#define SSB_EXTIF_GPIO_INTPOL		0x0094
+#define SSB_EXTIF_GPIO_INTMASK		0x0098
+#define SSB_EXTIF_UART_DATA		0x0300
+#define SSB_EXTIF_UART_TIMER		0x0310
+#define SSB_EXTIF_UART_FCR		0x0320
+#define SSB_EXTIF_UART_LCR		0x0330
+#define SSB_EXTIF_UART_MCR		0x0340
+#define SSB_EXTIF_UART_LSR		0x0350
+#define SSB_EXTIF_UART_MSR		0x0360
+#define SSB_EXTIF_UART_SCRATCH		0x0370
+
+
+
+
+/* pcmcia/prog/flash_config */
+#define	SSB_EXTCFG_EN			(1 << 0)	/* enable */
+#define	SSB_EXTCFG_MODE			0xE		/* mode */
+#define	SSB_EXTCFG_MODE_SHIFT		1
+#define	 SSB_EXTCFG_MODE_FLASH		0x0		/* flash/asynchronous mode */
+#define	 SSB_EXTCFG_MODE_SYNC		0x2		/* synchronous mode */
+#define	 SSB_EXTCFG_MODE_PCMCIA		0x4		/* pcmcia mode */
+#define	SSB_EXTCFG_DS16			(1 << 4)	/* destsize:  0=8bit, 1=16bit */
+#define	SSB_EXTCFG_BSWAP		(1 << 5)	/* byteswap */
+#define	SSB_EXTCFG_CLKDIV		0xC0		/* clock divider */
+#define	SSB_EXTCFG_CLKDIV_SHIFT		6
+#define	 SSB_EXTCFG_CLKDIV_2		0x0		/* backplane/2 */
+#define	 SSB_EXTCFG_CLKDIV_3		0x40		/* backplane/3 */
+#define	 SSB_EXTCFG_CLKDIV_4		0x80		/* backplane/4 */
+#define	SSB_EXTCFG_CLKEN		(1 << 8)	/* clock enable */
+#define	SSB_EXTCFG_STROBE		(1 << 9)	/* size/bytestrobe (synch only) */
+
+/* pcmcia_memwait */
+#define	SSB_PCMCIA_MEMW_0		0x0000003F	/* waitcount0 */
+#define	SSB_PCMCIA_MEMW_1		0x00001F00	/* waitcount1 */
+#define	SSB_PCMCIA_MEMW_1_SHIFT		8
+#define	SSB_PCMCIA_MEMW_2		0x001F0000	/* waitcount2 */
+#define	SSB_PCMCIA_MEMW_2_SHIFT		16
+#define	SSB_PCMCIA_MEMW_3		0x1F000000	/* waitcount3 */
+#define	SSB_PCMCIA_MEMW_3_SHIFT		24
+
+/* pcmcia_attrwait */
+#define	SSB_PCMCIA_ATTW_0		0x0000003F	/* waitcount0 */
+#define	SSB_PCMCIA_ATTW_1		0x00001F00	/* waitcount1 */
+#define	SSB_PCMCIA_ATTW_1_SHIFT		8
+#define	SSB_PCMCIA_ATTW_2		0x001F0000	/* waitcount2 */
+#define	SSB_PCMCIA_ATTW_2_SHIFT		16
+#define	SSB_PCMCIA_ATTW_3		0x1F000000	/* waitcount3 */
+#define	SSB_PCMCIA_ATTW_3_SHIFT		24
+
+/* pcmcia_iowait */
+#define	SSB_PCMCIA_IOW_0		0x0000003F	/* waitcount0 */
+#define	SSB_PCMCIA_IOW_1		0x00001F00	/* waitcount1 */
+#define	SSB_PCMCIA_IOW_1_SHIFT		8
+#define	SSB_PCMCIA_IOW_2		0x001F0000	/* waitcount2 */
+#define	SSB_PCMCIA_IOW_2_SHIFT		16
+#define	SSB_PCMCIA_IOW_3		0x1F000000	/* waitcount3 */
+#define	SSB_PCMCIA_IOW_3_SHIFT		24
+
+/* prog_waitcount */
+#define	SSB_PROG_WCNT_0			0x0000001F	/* waitcount0 */
+#define	SSB_PROG_WCNT_1			0x00001F00	/* waitcount1 */
+#define	SSB_PROG_WCNT_1_SHIFT		8
+#define	SSB_PROG_WCNT_2			0x001F0000	/* waitcount2 */
+#define	SSB_PROG_WCNT_2_SHIFT		16
+#define	SSB_PROG_WCNT_3			0x1F000000	/* waitcount3 */
+#define	SSB_PROG_WCNT_3_SHIFT		24
+
+#define SSB_PROG_W0			0x0000000C
+#define SSB_PROG_W1			0x00000A00
+#define SSB_PROG_W2			0x00020000
+#define SSB_PROG_W3			0x01000000
+
+/* flash_waitcount */
+#define	SSB_FLASH_WCNT_0		0x0000001F	/* waitcount0 */
+#define	SSB_FLASH_WCNT_1		0x00001F00	/* waitcount1 */
+#define	SSB_FLASH_WCNT_1_SHIFT		8
+#define	SSB_FLASH_WCNT_2		0x001F0000	/* waitcount2 */
+#define	SSB_FLASH_WCNT_2_SHIFT		16
+#define	SSB_FLASH_WCNT_3		0x1F000000	/* waitcount3 */
+#define	SSB_FLASH_WCNT_3_SHIFT		24
+
+/* watchdog */
+#define SSB_EXTIF_WATCHDOG_CLK		48000000	/* Hz */
+
+
+#endif /* LINUX_SSB_EXTIFCORE_H_ */
diff --git a/include/linux/ssb/ssb_driver_mips.h b/include/linux/ssb/ssb_driver_mips.h
new file mode 100644
index 0000000..cdbb985
--- /dev/null
+++ b/include/linux/ssb/ssb_driver_mips.h
@@ -0,0 +1,44 @@
+#ifndef LINUX_SSB_MIPSCORE_H_
+#define LINUX_SSB_MIPSCORE_H_
+
+#ifdef CONFIG_SSB_DRIVER_MIPS
+
+struct ssb_device;
+
+struct ssb_serial_port {
+	void *regs;
+	unsigned long clockspeed;
+	unsigned int irq;
+	unsigned int baud_base;
+	unsigned int reg_shift;
+};
+
+
+struct ssb_mipscore {
+	struct ssb_device *dev;
+
+	int nr_serial_ports;
+	struct ssb_serial_port serial_ports[4];
+
+	u32 flash_window;
+	u32 flash_window_size;
+};
+
+extern void ssb_mipscore_init(struct ssb_mipscore *mcore);
+
+extern unsigned int ssb_mips_irq(struct ssb_device *dev);
+
+
+#else /* CONFIG_SSB_DRIVER_MIPS */
+
+struct ssb_mipscore {
+};
+
+static inline
+void ssb_mipscore_init(struct ssb_mipscore *mcore)
+{
+}
+
+#endif /* CONFIG_SSB_DRIVER_MIPS */
+
+#endif /* LINUX_SSB_MIPSCORE_H_ */
diff --git a/include/linux/ssb/ssb_driver_pci.h b/include/linux/ssb/ssb_driver_pci.h
new file mode 100644
index 0000000..9cfffb7
--- /dev/null
+++ b/include/linux/ssb/ssb_driver_pci.h
@@ -0,0 +1,106 @@
+#ifndef LINUX_SSB_PCICORE_H_
+#define LINUX_SSB_PCICORE_H_
+
+#ifdef CONFIG_SSB_DRIVER_PCICORE
+
+/* PCI core registers. */
+#define SSB_PCICORE_CTL			0x0000	/* PCI Control */
+#define  SSB_PCICORE_CTL_RST_OE		0x00000001 /* PCI_RESET Output Enable */
+#define  SSB_PCICORE_CTL_RST		0x00000002 /* PCI_RESET driven out to pin */
+#define  SSB_PCICORE_CTL_CLK_OE		0x00000004 /* Clock gate Output Enable */
+#define  SSB_PCICORE_CTL_CLK		0x00000008 /* Gate for clock driven out to pin */
+#define SSB_PCICORE_ARBCTL		0x0010	/* PCI Arbiter Control */
+#define  SSB_PCICORE_ARBCTL_INTERN	0x00000001 /* Use internal arbiter */
+#define  SSB_PCICORE_ARBCTL_EXTERN	0x00000002 /* Use external arbiter */
+#define  SSB_PCICORE_ARBCTL_PARKID	0x00000006 /* Mask, selects which agent is parked on an idle bus */
+#define   SSB_PCICORE_ARBCTL_PARKID_LAST	0x00000000 /* Last requestor */
+#define   SSB_PCICORE_ARBCTL_PARKID_4710	0x00000002 /* 4710 */
+#define   SSB_PCICORE_ARBCTL_PARKID_EXT0	0x00000004 /* External requestor 0 */
+#define   SSB_PCICORE_ARBCTL_PARKID_EXT1	0x00000006 /* External requestor 1 */
+#define SSB_PCICORE_ISTAT		0x0020	/* Interrupt status */
+#define  SSB_PCICORE_ISTAT_INTA		0x00000001 /* PCI INTA# */
+#define  SSB_PCICORE_ISTAT_INTB		0x00000002 /* PCI INTB# */
+#define  SSB_PCICORE_ISTAT_SERR		0x00000004 /* PCI SERR# (write to clear) */
+#define  SSB_PCICORE_ISTAT_PERR		0x00000008 /* PCI PERR# (write to clear) */
+#define  SSB_PCICORE_ISTAT_PME		0x00000010 /* PCI PME# */
+#define SSB_PCICORE_IMASK		0x0024	/* Interrupt mask */
+#define  SSB_PCICORE_IMASK_INTA		0x00000001 /* PCI INTA# */
+#define  SSB_PCICORE_IMASK_INTB		0x00000002 /* PCI INTB# */
+#define  SSB_PCICORE_IMASK_SERR		0x00000004 /* PCI SERR# */
+#define  SSB_PCICORE_IMASK_PERR		0x00000008 /* PCI PERR# */
+#define  SSB_PCICORE_IMASK_PME		0x00000010 /* PCI PME# */
+#define SSB_PCICORE_MBOX		0x0028	/* Backplane to PCI Mailbox */
+#define  SSB_PCICORE_MBOX_F0_0		0x00000100 /* PCI function 0, INT 0 */
+#define  SSB_PCICORE_MBOX_F0_1		0x00000200 /* PCI function 0, INT 1 */
+#define  SSB_PCICORE_MBOX_F1_0		0x00000400 /* PCI function 1, INT 0 */
+#define  SSB_PCICORE_MBOX_F1_1		0x00000800 /* PCI function 1, INT 1 */
+#define  SSB_PCICORE_MBOX_F2_0		0x00001000 /* PCI function 2, INT 0 */
+#define  SSB_PCICORE_MBOX_F2_1		0x00002000 /* PCI function 2, INT 1 */
+#define  SSB_PCICORE_MBOX_F3_0		0x00004000 /* PCI function 3, INT 0 */
+#define  SSB_PCICORE_MBOX_F3_1		0x00008000 /* PCI function 3, INT 1 */
+#define SSB_PCICORE_BCAST_ADDR		0x0050	/* Backplane Broadcast Address */
+#define  SSB_PCICORE_BCAST_ADDR_MASK	0x000000FF
+#define SSB_PCICORE_BCAST_DATA		0x0054	/* Backplane Broadcast Data */
+#define SSB_PCICORE_GPIO_IN		0x0060	/* rev >= 2 only */
+#define SSB_PCICORE_GPIO_OUT		0x0064	/* rev >= 2 only */
+#define SSB_PCICORE_GPIO_ENABLE		0x0068	/* rev >= 2 only */
+#define SSB_PCICORE_GPIO_CTL		0x006C	/* rev >= 2 only */
+#define SSB_PCICORE_SBTOPCI0		0x0100	/* Backplane to PCI translation 0 (sbtopci0) */
+#define  SSB_PCICORE_SBTOPCI0_MASK	0xFC000000
+#define SSB_PCICORE_SBTOPCI1		0x0104	/* Backplane to PCI translation 1 (sbtopci1) */
+#define  SSB_PCICORE_SBTOPCI1_MASK	0xFC000000
+#define SSB_PCICORE_SBTOPCI2		0x0108	/* Backplane to PCI translation 2 (sbtopci2) */
+#define  SSB_PCICORE_SBTOPCI2_MASK	0xC0000000
+
+/* SBtoPCIx */
+#define SSB_PCICORE_SBTOPCI_MEM		0x00000000
+#define SSB_PCICORE_SBTOPCI_IO		0x00000001
+#define SSB_PCICORE_SBTOPCI_CFG0	0x00000002
+#define SSB_PCICORE_SBTOPCI_CFG1	0x00000003
+#define SSB_PCICORE_SBTOPCI_PREF	0x00000004 /* Prefetch enable */
+#define SSB_PCICORE_SBTOPCI_BURST	0x00000008 /* Burst enable */
+#define SSB_PCICORE_SBTOPCI_MRM		0x00000020 /* Memory Read Multiple */
+#define SSB_PCICORE_SBTOPCI_RC		0x00000030 /* Read Command mask (rev >= 11) */
+#define  SSB_PCICORE_SBTOPCI_RC_READ	0x00000000 /* Memory read */
+#define  SSB_PCICORE_SBTOPCI_RC_READL	0x00000010 /* Memory read line */
+#define  SSB_PCICORE_SBTOPCI_RC_READM	0x00000020 /* Memory read multiple */
+
+
+/* PCIcore specific boardflags */
+#define SSB_PCICORE_BFL_NOPCI		0x00000400 /* Board leaves PCI floating */
+
+
+struct ssb_pcicore {
+	struct ssb_device *dev;
+	u8 setup_done:1;
+	u8 hostmode:1;
+	u8 cardbusmode:1;
+};
+
+extern void ssb_pcicore_init(struct ssb_pcicore *pc);
+
+/* Enable IRQ routing for a specific device */
+extern int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc,
+					  struct ssb_device *dev);
+
+
+#else /* CONFIG_SSB_DRIVER_PCICORE */
+
+
+struct ssb_pcicore {
+};
+
+static inline
+void ssb_pcicore_init(struct ssb_pcicore *pc)
+{
+}
+
+static inline
+int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc,
+				   struct ssb_device *dev)
+{
+	return 0;
+}
+
+#endif /* CONFIG_SSB_DRIVER_PCICORE */
+#endif /* LINUX_SSB_PCICORE_H_ */
diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
new file mode 100644
index 0000000..8326377
--- /dev/null
+++ b/include/linux/ssb/ssb.h
@@ -0,0 +1,432 @@
+#ifndef LINUX_SSB_H_
+#define LINUX_SSB_H_
+
+#include <linux/device.h>
+#include <linux/list.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+#include <linux/pci.h>
+
+#include <linux/ssb/ssb_regs.h>
+
+
+struct pcmcia_device;
+struct ssb_bus;
+struct ssb_driver;
+
+
+struct ssb_sprom_r1 {
+	u16 pci_spid;		/* Subsystem Product ID for PCI */
+	u16 pci_svid;		/* Subsystem Vendor ID for PCI */
+	u16 pci_pid;		/* Product ID for PCI */
+	u8 il0mac[6];		/* MAC address for 802.11b/g */
+	u8 et0mac[6];		/* MAC address for Ethernet */
+	u8 et1mac[6];		/* MAC address for 802.11a */
+	u8 et0phyaddr:5;	/* MII address for enet0 */
+	u8 et1phyaddr:5;	/* MII address for enet1 */
+	u8 et0mdcport:1;	/* MDIO for enet0 */
+	u8 et1mdcport:1;	/* MDIO for enet1 */
+	u8 board_rev;		/* Board revision */
+	u8 country_code:4;	/* Country Code */
+	u8 antenna_a:2;		/* Antenna 0/1 available for A-PHY */
+	u8 antenna_bg:2;	/* Antenna 0/1 available for B-PHY and G-PHY */
+	u16 pa0b0;
+	u16 pa0b1;
+	u16 pa0b2;
+	u16 pa1b0;
+	u16 pa1b1;
+	u16 pa1b2;
+	u8 gpio0;		/* GPIO pin 0 */
+	u8 gpio1;		/* GPIO pin 1 */
+	u8 gpio2;		/* GPIO pin 2 */
+	u8 gpio3;		/* GPIO pin 3 */
+	u16 maxpwr_a;		/* A-PHY Power Amplifier Max Power (in dBm Q5.2) */
+	u16 maxpwr_bg;		/* B/G-PHY Power Amplifier Max Power (in dBm Q5.2) */
+	u8 itssi_a;		/* Idle TSSI Target for A-PHY */
+	u8 itssi_bg;		/* Idle TSSI Target for B/G-PHY */
+	u16 boardflags_lo;	/* Boardflags (low 16 bits) */
+	u8 antenna_gain_a;	/* A-PHY Antenna gain (in dBm Q5.2) */
+	u8 antenna_gain_bg;	/* B/G-PHY Antenna gain (in dBm Q5.2) */
+	u8 oem[8];		/* OEM string (rev 1 only) */
+};
+
+struct ssb_sprom_r2 {
+	u16 boardflags_hi;	/* Boardflags (high 16 bits) */
+	u8 maxpwr_a_lo;		/* A-PHY Max Power Low */
+	u8 maxpwr_a_hi;		/* A-PHY Max Power High */
+	u16 pa1lob0;		/* A-PHY PA Low Settings */
+	u16 pa1lob1;		/* A-PHY PA Low Settings */
+	u16 pa1lob2;		/* A-PHY PA Low Settings */
+	u16 pa1hib0;		/* A-PHY PA High Settings */
+	u16 pa1hib1;		/* A-PHY PA High Settings */
+	u16 pa1hib2;		/* A-PHY PA High Settings */
+	u8 ofdm_pwr_off;	/* OFDM Power Offset from CCK Level */
+	u8 country_str[2];	/* Two char Country Code */
+};
+
+struct ssb_sprom_r3 {
+	u32 ofdmapo;		/* A-PHY OFDM Mid Power Offset */
+	u32 ofdmalpo;		/* A-PHY OFDM Low Power Offset */
+	u32 ofdmahpo;		/* A-PHY OFDM High Power Offset */
+	u8 gpioldc_on_cnt;	/* GPIO LED Powersave Duty Cycle ON count */
+	u8 gpioldc_off_cnt;	/* GPIO LED Powersave Duty Cycle OFF count */
+	u8 cckpo_1M:4;		/* CCK Power Offset for Rate 1M */
+	u8 cckpo_2M:4;		/* CCK Power Offset for Rate 2M */
+	u8 cckpo_55M:4;		/* CCK Power Offset for Rate 5.5M */
+	u8 cckpo_11M:4;		/* CCK Power Offset for Rate 11M */
+	u32 ofdmgpo;		/* G-PHY OFDM Power Offset */
+};
+
+struct ssb_sprom_r4 {
+	/* TODO */
+};
+
+struct ssb_sprom {
+	u8 revision;
+	u8 crc;
+	/* The valid r# fields are selected by the "revision".
+	 * Revision 3 and lower inherit from lower revisions.
+	 */
+	union {
+		struct {
+			struct ssb_sprom_r1 r1;
+			struct ssb_sprom_r2 r2;
+			struct ssb_sprom_r3 r3;
+		};
+		struct ssb_sprom_r4 r4;
+	};
+};
+
+/* Information about the PCB the circuitry is soldered on. */
+struct ssb_boardinfo {
+	u16 vendor;
+	u16 type;
+	u16 rev;
+};
+
+
+struct ssb_device;
+/* Lowlevel read/write operations on the device MMIO.
+ * Internal, don't use that outside of ssb. */
+struct ssb_bus_ops {
+	u16 (*read16)(struct ssb_device *dev, u16 offset);
+	u32 (*read32)(struct ssb_device *dev, u16 offset);
+	void (*write16)(struct ssb_device *dev, u16 offset, u16 value);
+	void (*write32)(struct ssb_device *dev, u16 offset, u32 value);
+};
+
+
+/* Core-ID values. */
+#define SSB_DEV_CHIPCOMMON	0x800
+#define SSB_DEV_ILINE20		0x801
+#define SSB_DEV_SDRAM		0x803
+#define SSB_DEV_PCI		0x804
+#define SSB_DEV_MIPS		0x805
+#define SSB_DEV_ETHERNET	0x806
+#define SSB_DEV_V90		0x807
+#define SSB_DEV_USB11_HOSTDEV	0x808
+#define SSB_DEV_ADSL		0x809
+#define SSB_DEV_ILINE100	0x80A
+#define SSB_DEV_IPSEC		0x80B
+#define SSB_DEV_PCMCIA		0x80D
+#define SSB_DEV_INTERNAL_MEM	0x80E
+#define SSB_DEV_MEMC_SDRAM	0x80F
+#define SSB_DEV_EXTIF		0x811
+#define SSB_DEV_80211		0x812
+#define SSB_DEV_MIPS_3302	0x816
+#define SSB_DEV_USB11_HOST	0x817
+#define SSB_DEV_USB11_DEV	0x818
+#define SSB_DEV_USB20_HOST	0x819
+#define SSB_DEV_USB20_DEV	0x81A
+#define SSB_DEV_SDIO_HOST	0x81B
+#define SSB_DEV_ROBOSWITCH	0x81C
+#define SSB_DEV_PARA_ATA	0x81D
+#define SSB_DEV_SATA_XORDMA	0x81E
+#define SSB_DEV_ETHERNET_GBIT	0x81F
+#define SSB_DEV_PCIE		0x820
+#define SSB_DEV_MIMO_PHY	0x821
+#define SSB_DEV_SRAM_CTRLR	0x822
+#define SSB_DEV_MINI_MACPHY	0x823
+#define SSB_DEV_ARM_1176	0x824
+#define SSB_DEV_ARM_7TDMI	0x825
+
+/* Vendor-ID values */
+#define SSB_VENDOR_BROADCOM	0x4243
+
+struct ssb_device_id {
+	u16 vendor;
+	u16 coreid;
+	u8 revision;
+};
+#define SSB_DEVICE(_vendor, _coreid, _revision)  \
+	{ .vendor = _vendor, .coreid = _coreid, .revision = _revision, }
+#define SSB_DEVTABLE_END  \
+	{ 0, },
+
+#define SSB_ANY_VENDOR		0xFFFF
+#define SSB_ANY_ID		0xFFFF
+#define SSB_ANY_REV		0xFF
+
+/* Some kernel subsystems poke with dev->drvdata, so we must use the
+ * following ugly workaround to get from struct device to struct ssb_device */
+struct __ssb_dev_wrapper {
+	struct device dev;
+	struct ssb_device *sdev;
+};
+
+struct ssb_device {
+	/* Having a copy of the ops pointer in each dev struct
+	 * is an optimization. */
+	const struct ssb_bus_ops *ops;
+
+	struct device *dev;
+	struct ssb_bus *bus;
+	struct ssb_device_id id;
+
+	u8 core_index;
+	unsigned int irq;
+
+	/* Internal-only stuff follows. */
+	void *drvdata;		/* Per-device data */
+	void *devtypedata;	/* Per-devicetype (eg 802.11) data */
+};
+
+/* Go from struct device to struct ssb_device. */
+static inline
+struct ssb_device * dev_to_ssb_dev(struct device *dev)
+{
+	struct __ssb_dev_wrapper *wrap;
+	wrap = container_of(dev, struct __ssb_dev_wrapper, dev);
+	return wrap->sdev;
+}
+
+/* Device specific user data */
+static inline
+void ssb_set_drvdata(struct ssb_device *dev, void *data)
+{
+	dev->drvdata = data;
+}
+static inline
+void * ssb_get_drvdata(struct ssb_device *dev)
+{
+	return dev->drvdata;
+}
+
+/* Devicetype specific user data. This is per device-type (not per device) */
+void ssb_set_devtypedata(struct ssb_device *dev, void *data);
+static inline
+void * ssb_get_devtypedata(struct ssb_device *dev)
+{
+	return dev->devtypedata;
+}
+
+
+struct ssb_driver {
+	const char *name;
+	const struct ssb_device_id *id_table;
+
+	int (*probe)(struct ssb_device *dev, const struct ssb_device_id *id);
+	void (*remove)(struct ssb_device *dev);
+	int (*suspend)(struct ssb_device *dev, pm_message_t state);
+	int (*resume)(struct ssb_device *dev);
+	void (*shutdown)(struct ssb_device *dev);
+
+	struct device_driver drv;
+};
+#define drv_to_ssb_drv(_drv) container_of(_drv, struct ssb_driver, drv)
+
+extern int __ssb_driver_register(struct ssb_driver *drv, struct module *owner);
+static inline int ssb_driver_register(struct ssb_driver *drv)
+{
+	return __ssb_driver_register(drv, THIS_MODULE);
+}
+extern void ssb_driver_unregister(struct ssb_driver *drv);
+
+
+
+
+enum ssb_bustype {
+	SSB_BUSTYPE_SSB,	/* This SSB bus is the system bus */
+	SSB_BUSTYPE_PCI,	/* SSB is connected to PCI bus */
+	SSB_BUSTYPE_PCMCIA,	/* SSB is connected to PCMCIA bus */
+};
+
+/* board_vendor */
+#define SSB_BOARDVENDOR_BCM	0x14E4	/* Broadcom */
+#define SSB_BOARDVENDOR_DELL	0x1028	/* Dell */
+#define SSB_BOARDVENDOR_HP	0x0E11	/* HP */
+/* board_type */
+#define SSB_BOARD_BCM94306MP	0x0418
+#define SSB_BOARD_BCM4309G	0x0421
+#define SSB_BOARD_BCM4306CB	0x0417
+#define SSB_BOARD_BCM4309MP	0x040C
+#define SSB_BOARD_MP4318	0x044A
+#define SSB_BOARD_BU4306	0x0416
+#define SSB_BOARD_BU4309	0x040A
+/* chip_package */
+#define SSB_CHIPPACK_BCM4712S	1	/* Small 200pin 4712 */
+#define SSB_CHIPPACK_BCM4712M	2	/* Medium 225pin 4712 */
+#define SSB_CHIPPACK_BCM4712L	0	/* Large 340pin 4712 */
+
+#include <linux/ssb/ssb_driver_chipcommon.h>
+#include <linux/ssb/ssb_driver_mips.h>
+#include <linux/ssb/ssb_driver_extif.h>
+#include <linux/ssb/ssb_driver_pci.h>
+
+struct ssb_bus {
+	/* The MMIO area. */
+	void __iomem *mmio;
+
+	const struct ssb_bus_ops *ops;
+
+	/* The core in the basic address register window. (PCI bus only) */
+	struct ssb_device *mapped_device;
+	/* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */
+	u8 mapped_pcmcia_seg;
+	/* Lock for core and segment switching. */
+	spinlock_t bar_lock;
+
+	/* The bus this backplane is running on. */
+	enum ssb_bustype bustype;
+	/* Pointer to the PCI bus (only valid if bustype == SSB_BUSTYPE_PCI). */
+	struct pci_dev *host_pci;
+	/* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */
+	struct pcmcia_device *host_pcmcia;
+
+#ifdef CONFIG_SSB_PCIHOST
+	/* Mutex to protect the SPROM writing. */
+	struct mutex pci_sprom_mutex;
+#endif
+
+	/* ID information about the Chip. */
+	u16 chip_id;
+	u16 chip_rev;
+	u8 chip_package;
+
+	/* List of devices (cores) on the backplane. */
+	struct ssb_device devices[SSB_MAX_NR_CORES];
+	u8 nr_devices;
+
+	/* Reference count. Number of suspended devices. */
+	u8 suspend_cnt;
+
+	/* Software ID number for this bus. */
+	unsigned int busnumber;
+
+	/* The ChipCommon device (if available). */
+	struct ssb_chipcommon chipco;
+	/* The PCI-core device (if available). */
+	struct ssb_pcicore pcicore;
+	/* The MIPS-core device (if available). */
+	struct ssb_mipscore mipscore;
+	/* The EXTif-core device (if available). */
+	struct ssb_extif extif;
+
+	/* The following structure elements are not available in early
+	 * SSB initialization. Though, they are available for regular
+	 * registered drivers at any stage. So be careful when
+	 * using them in the ssb core code. */
+
+	/* ID information about the PCB. */
+	struct ssb_boardinfo boardinfo;
+	/* Contents of the SPROM. */
+	struct ssb_sprom sprom;
+
+	/* Internal. */
+	struct list_head list;
+};
+
+/* The initialization-invariants. */
+struct ssb_init_invariants {
+	struct ssb_boardinfo boardinfo;
+	struct ssb_sprom sprom;
+};
+/* Type of function to fetch the invariants. */
+typedef int (*ssb_invariants_func_t)(struct ssb_bus *bus,
+				     struct ssb_init_invariants *iv);
+
+/* Register a SSB system bus. get_invariants() is called after the
+ * basic system devices are initialized.
+ * The invariants are usually fetched from some NVRAM.
+ * Put the invariants into the struct pointed to by iv. */
+extern int ssb_bus_ssbbus_register(struct ssb_bus *bus,
+				   unsigned long baseaddr,
+				   ssb_invariants_func_t get_invariants);
+#ifdef CONFIG_SSB_PCIHOST
+extern int ssb_bus_pcibus_register(struct ssb_bus *bus,
+				   struct pci_dev *host_pci);
+#endif /* CONFIG_SSB_PCIHOST */
+#ifdef CONFIG_SSB_PCMCIAHOST
+extern int ssb_bus_pcmciabus_register(struct ssb_bus *bus,
+				      struct pcmcia_device *pcmcia_dev,
+				      unsigned long baseaddr);
+#endif /* CONFIG_SSB_PCMCIAHOST */
+
+extern void ssb_bus_unregister(struct ssb_bus *bus);
+
+extern u32 ssb_clockspeed(struct ssb_bus *bus);
+
+/* Is the device enabled in hardware? */
+int ssb_device_is_enabled(struct ssb_device *dev);
+/* Enable a device and pass device-specific SSB_TMSLOW flags.
+ * If no device-specific flags are available, use 0. */
+void ssb_device_enable(struct ssb_device *dev, u32 core_specific_flags);
+/* Disable a device in hardware and pass SSB_TMSLOW flags (if any). */
+void ssb_device_disable(struct ssb_device *dev, u32 core_specific_flags);
+
+
+/* Device MMIO register read/write functions. */
+static inline u16 ssb_read16(struct ssb_device *dev, u16 offset)
+{
+	return dev->ops->read16(dev, offset);
+}
+static inline u32 ssb_read32(struct ssb_device *dev, u16 offset)
+{
+	return dev->ops->read32(dev, offset);
+}
+static inline void ssb_write16(struct ssb_device *dev, u16 offset, u16 value)
+{
+	dev->ops->write16(dev, offset, value);
+}
+static inline void ssb_write32(struct ssb_device *dev, u16 offset, u32 value)
+{
+	dev->ops->write32(dev, offset, value);
+}
+
+
+/* Translation (routing) bits that need to be ORed to DMA
+ * addresses before they are given to a device. */
+extern u32 ssb_dma_translation(struct ssb_device *dev);
+#define SSB_DMA_TRANSLATION_MASK	0xC0000000
+#define SSB_DMA_TRANSLATION_SHIFT	30
+
+extern int ssb_dma_set_mask(struct ssb_device *ssb_dev, u64 mask);
+
+
+#ifdef CONFIG_SSB_PCIHOST
+/* PCI-host wrapper driver */
+extern int ssb_pcihost_register(struct pci_driver *driver);
+static inline void ssb_pcihost_unregister(struct pci_driver *driver)
+{
+	pci_unregister_driver(driver);
+}
+#endif /* CONFIG_SSB_PCIHOST */
+
+
+/* If a driver is shutdown or suspended, call this to signal
+ * that the bus may be completely powered down. SSB will decide,
+ * if it's really time to power down the bus, based on if there
+ * are other devices that want to run. */
+extern int ssb_bus_may_powerdown(struct ssb_bus *bus);
+/* Before initializing and enabling a device, call this to power-up the bus.
+ * If you want to allow use of dynamic-power-control, pass the flag.
+ * Otherwise static always-on powercontrol will be used. */
+extern int ssb_bus_powerup(struct ssb_bus *bus, bool dynamic_pctl);
+
+
+/* Various helper functions */
+extern u32 ssb_admatch_base(u32 adm);
+extern u32 ssb_admatch_size(u32 adm);
+
+
+#endif /* LINUX_SSB_H_ */
diff --git a/include/linux/ssb/ssb_regs.h b/include/linux/ssb/ssb_regs.h
new file mode 100644
index 0000000..66751a6
--- /dev/null
+++ b/include/linux/ssb/ssb_regs.h
@@ -0,0 +1,292 @@
+#ifndef LINUX_SSB_REGS_H_
+#define LINUX_SSB_REGS_H_
+
+
+/* SiliconBackplane Address Map.
+ * All regions may not exist on all chips.
+ */
+#define SSB_SDRAM_BASE		0x00000000	/* Physical SDRAM */
+#define SSB_PCI_MEM		0x08000000	/* Host Mode sb2pcitranslation0 (64 MB) */
+#define SSB_PCI_CFG		0x0c000000	/* Host Mode sb2pcitranslation1 (64 MB) */
+#define	SSB_SDRAM_SWAPPED	0x10000000	/* Byteswapped Physical SDRAM */
+#define SSB_ENUM_BASE    	0x18000000	/* Enumeration space base */
+#define	SSB_ENUM_LIMIT		0x18010000	/* Enumeration space limit */
+
+#define	SSB_FLASH2		0x1c000000	/* Flash Region 2 (region 1 shadowed here) */
+#define	SSB_FLASH2_SZ		0x02000000	/* Size of Flash Region 2 */
+
+#define	SSB_EXTIF_BASE		0x1f000000	/* External Interface region base address */
+#define	SSB_FLASH1		0x1fc00000	/* Flash Region 1 */
+#define	SSB_FLASH1_SZ		0x00400000	/* Size of Flash Region 1 */
+
+#define SSB_PCI_DMA		0x40000000	/* Client Mode sb2pcitranslation2 (1 GB) */
+#define SSB_PCI_DMA_SZ		0x40000000	/* Client Mode sb2pcitranslation2 size in bytes */
+#define SSB_PCIE_DMA_L32	0x00000000	/* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */
+#define SSB_PCIE_DMA_H32	0x80000000	/* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */
+#define	SSB_EUART		(SSB_EXTIF_BASE + 0x00800000)
+#define	SSB_LED			(SSB_EXTIF_BASE + 0x00900000)
+
+
+/* Enumeration space constants */
+#define SSB_CORE_SIZE		0x1000	/* Size of a core MMIO area */
+#define SSB_MAX_NR_CORES	((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE)
+
+
+/* mips address */
+#define	SSB_EJTAG		0xff200000	/* MIPS EJTAG space (2M) */
+
+
+/* SSB PCI config space registers. */
+#define SSB_PMCSR		0x44
+#define  SSB_PE			0x100
+#define	SSB_BAR0_WIN		0x80	/* Backplane address space 0 */
+#define	SSB_BAR1_WIN		0x84	/* Backplane address space 1 */
+#define	SSB_SPROMCTL		0x88	/* SPROM control */
+#define  SSB_SPROMCTL_WE	0x10	/* SPROM write enable */
+#define	SSB_BAR1_CONTROL	0x8c	/* Address space 1 burst control */
+#define SSB_PCI_IRQS		0x90	/* PCI interrupts */
+#define SSB_PCI_IRQMASK		0x94	/* PCI IRQ control and mask (pcirev >= 6 only) */
+#define SSB_BACKPLANE_IRQS	0x98	/* Backplane Interrupts */
+#define SSB_GPIO_IN		0xB0	/* GPIO Input (pcirev >= 3 only) */
+#define SSB_GPIO_OUT		0xB4	/* GPIO Output (pcirev >= 3 only) */
+#define SSB_GPIO_OUT_ENABLE	0xB8	/* GPIO Output Enable/Disable (pcirev >= 3 only) */
+#define  SSB_GPIO_SCS		0x10	/* PCI config space bit 4 for 4306c0 slow clock source */
+#define  SSB_GPIO_HWRAD		0x20	/* PCI config space GPIO 13 for hw radio disable */
+#define  SSB_GPIO_XTAL		0x40	/* PCI config space GPIO 14 for Xtal powerup */
+#define  SSB_GPIO_PLL		0x80	/* PCI config space GPIO 15 for PLL powerdown */
+
+
+#define SSB_BAR0_MAX_RETRIES	50
+
+/* Silicon backplane configuration register definitions */
+#define SSB_IPSFLAG		0x0F08
+#define	 SSB_IPSFLAG_IRQ1	0x0000003F /* which sbflags get routed to mips interrupt 1 */
+#define	 SSB_IPSFLAG_IRQ1_SHIFT	0
+#define	 SSB_IPSFLAG_IRQ2	0x00003F00 /* which sbflags get routed to mips interrupt 2 */
+#define	 SSB_IPSFLAG_IRQ2_SHIFT	8
+#define	 SSB_IPSFLAG_IRQ3	0x003F0000 /* which sbflags get routed to mips interrupt 3 */
+#define	 SSB_IPSFLAG_IRQ3_SHIFT	16
+#define	 SSB_IPSFLAG_IRQ4	0x3F000000 /* which sbflags get routed to mips interrupt 4 */
+#define	 SSB_IPSFLAG_IRQ4_SHIFT	24
+#define SSB_TPSFLAG		0x0F18
+#define  SSB_TPSFLAG_BPFLAG	0x0000003F /* Backplane flag # */
+#define  SSB_TPSFLAG_ALWAYSIRQ	0x00000040 /* IRQ is always sent on the Backplane */
+#define SSB_TMERRLOGA		0x0F48
+#define SSB_TMERRLOG		0x0F50
+#define SSB_ADMATCH3		0x0F60
+#define SSB_ADMATCH2		0x0F68
+#define SSB_ADMATCH1		0x0F70
+#define SSB_IMSTATE		0x0F90     /* SB Initiator Agent State */
+#define  SSB_IMSTATE_PC		0x0000000f /* Pipe Count */
+#define  SSB_IMSTATE_AP_MASK	0x00000030 /* Arbitration Priority */
+#define  SSB_IMSTATE_AP_BOTH	0x00000000 /* Use both timeslices and token */
+#define  SSB_IMSTATE_AP_TS	0x00000010 /* Use timeslices only */
+#define  SSB_IMSTATE_AP_TK	0x00000020 /* Use token only */
+#define  SSB_IMSTATE_AP_RSV	0x00000030 /* Reserved */
+#define  SSB_IMSTATE_IBE	0x00020000 /* In Band Error */
+#define  SSB_IMSTATE_TO		0x00040000 /* Timeout */
+#define SSB_INTVEC		0x0F94     /* SB Interrupt Mask */
+#define  SSB_INTVEC_PCI		0x00000001 /* Enable interrupts for PCI */
+#define  SSB_INTVEC_ENET0	0x00000002 /* Enable interrupts for enet 0 */
+#define  SSB_INTVEC_ILINE20	0x00000004 /* Enable interrupts for iline20 */
+#define  SSB_INTVEC_CODEC	0x00000008 /* Enable interrupts for v90 codec */
+#define  SSB_INTVEC_USB		0x00000010 /* Enable interrupts for usb */
+#define  SSB_INTVEC_EXTIF	0x00000020 /* Enable interrupts for external i/f */
+#define  SSB_INTVEC_ENET1	0x00000040 /* Enable interrupts for enet 1 */
+#define SSB_TMSLOW		0x0F98     /* SB Target State Low */
+#define  SSB_TMSLOW_RESET	0x00000001 /* Reset */
+#define  SSB_TMSLOW_REJECT_22	0x00000002 /* Reject (Backplane rev 2.2) */
+#define  SSB_TMSLOW_REJECT_23	0x00000004 /* Reject (Backplane rev 2.3) */
+#define  SSB_TMSLOW_CLOCK	0x00010000 /* Clock Enable */
+#define  SSB_TMSLOW_FGC		0x00020000 /* Force Gated Clocks On */
+#define  SSB_TMSLOW_PE		0x40000000 /* Power Management Enable */
+#define  SSB_TMSLOW_BE		0x80000000 /* BIST Enable */
+#define SSB_TMSHIGH		0x0F9C     /* SB Target State High */
+#define  SSB_TMSHIGH_SERR	0x00000001 /* S-error */
+#define  SSB_TMSHIGH_INT	0x00000002 /* Interrupt */
+#define  SSB_TMSHIGH_BUSY	0x00000004 /* Busy */
+#define  SSB_TMSHIGH_TO		0x00000020 /* Timeout. Backplane rev >= 2.3 only */
+#define  SSB_TMSHIGH_COREFL	0x1FFF0000 /* Core specific flags */
+#define  SSB_TMSHIGH_COREFL_SHIFT	16
+#define  SSB_TMSHIGH_DMA64	0x10000000 /* 64bit DMA supported */
+#define  SSB_TMSHIGH_GCR	0x20000000 /* Gated Clock Request */
+#define  SSB_TMSHIGH_BISTF	0x40000000 /* BIST Failed */
+#define  SSB_TMSHIGH_BISTD	0x80000000 /* BIST Done */
+#define SSB_BWA0		0x0FA0
+#define SSB_IMCFGLO		0x0FA8
+#define  SSB_IMCFGLO_SERTO	0x00000007 /* Service timeout */
+#define  SSB_IMCFGLO_REQTO	0x00000070 /* Request timeout */
+#define  SSB_IMCFGLO_REQTO_SHIFT	4
+#define  SSB_IMCFGLO_CONNID	0x00FF0000 /* Connection ID */
+#define  SSB_IMCFGLO_CONNID_SHIFT	16
+#define SSB_IMCFGHI		0x0FAC
+#define SSB_ADMATCH0		0x0FB0
+#define SSB_TMCFGLO		0x0FB8
+#define SSB_TMCFGHI		0x0FBC
+#define SSB_BCONFIG		0x0FC0
+#define SSB_BSTATE		0x0FC8
+#define SSB_ACTCFG		0x0FD8
+#define SSB_FLAGST		0x0FE8
+#define SSB_IDLOW		0x0FF8
+#define  SSB_IDLOW_CFGSP	0x00000003 /* Config Space */
+#define  SSB_IDLOW_ADDRNGE	0x00000038 /* Address Ranges supported */
+#define  SSB_IDLOW_ADDRNGE_SHIFT	3
+#define  SSB_IDLOW_SYNC		0x00000040
+#define  SSB_IDLOW_INITIATOR	0x00000080
+#define  SSB_IDLOW_MIBL		0x00000F00 /* Minimum Backplane latency */
+#define  SSB_IDLOW_MIBL_SHIFT	8
+#define  SSB_IDLOW_MABL		0x0000F000 /* Maximum Backplane latency */
+#define  SSB_IDLOW_MABL_SHIFT	12
+#define  SSB_IDLOW_TIF		0x00010000 /* This Initiator is first */
+#define  SSB_IDLOW_CCW		0x000C0000 /* Cycle counter width */
+#define  SSB_IDLOW_CCW_SHIFT	18
+#define  SSB_IDLOW_TPT		0x00F00000 /* Target ports */
+#define  SSB_IDLOW_TPT_SHIFT	20
+#define  SSB_IDLOW_INITP	0x0F000000 /* Initiator ports */
+#define  SSB_IDLOW_INITP_SHIFT	24
+#define  SSB_IDLOW_SSBREV	0xF0000000 /* Sonics Backplane Revision code */
+#define  SSB_IDLOW_SSBREV_22	0x00000000 /* <= 2.2 */
+#define  SSB_IDLOW_SSBREV_23	0x10000000 /* 2.3 */
+#define SSB_IDHIGH		0x0FFC     /* SB Identification High */
+#define  SSB_IDHIGH_RCLO	0x0000000F /* Revision Code (low part) */
+#define  SSB_IDHIGH_CC		0x00008FF0 /* Core Code */
+#define  SSB_IDHIGH_CC_SHIFT	4
+#define  SSB_IDHIGH_RCHI	0x00007000 /* Revision Code (high part) */
+#define  SSB_IDHIGH_RCHI_SHIFT	8	   /* yes, shift 8 is right */
+#define  SSB_IDHIGH_VC		0xFFFF0000 /* Vendor Code */
+#define  SSB_IDHIGH_VC_SHIFT	16
+
+/* SPROM shadow area. If not otherwise noted, fields are
+ * two bytes wide. Note that the SPROM can _only_ be read
+ * in two-byte quantinies.
+ */
+#define SSB_SPROMSIZE_WORDS		64
+#define SSB_SPROMSIZE_BYTES		(SSB_SPROMSIZE_WORDS * sizeof(u16))
+#define SSB_SPROM_BASE			0x1000
+#define SSB_SPROM_REVISION		0x107E
+#define  SSB_SPROM_REVISION_REV		0x00FF	/* SPROM Revision number */
+#define  SSB_SPROM_REVISION_CRC		0xFF00	/* SPROM CRC8 value */
+#define  SSB_SPROM_REVISION_CRC_SHIFT	8
+/* SPROM Revision 1 */
+#define SSB_SPROM1_SPID			0x1004	/* Subsystem Product ID for PCI */
+#define SSB_SPROM1_SVID			0x1006	/* Subsystem Vendor ID for PCI */
+#define SSB_SPROM1_PID			0x1008	/* Product ID for PCI */
+#define SSB_SPROM1_IL0MAC		0x1048	/* 6 bytes MAC address for 802.11b/g */
+#define SSB_SPROM1_ET0MAC		0x104E	/* 6 bytes MAC address for Ethernet */
+#define SSB_SPROM1_ET1MAC		0x1054	/* 6 bytes MAC address for 802.11a */
+#define SSB_SPROM1_ETHPHY		0x105A	/* Ethernet PHY settings */
+#define  SSB_SPROM1_ETHPHY_ET0A		0x001F	/* MII Address for enet0 */
+#define  SSB_SPROM1_ETHPHY_ET1A		0x03E0	/* MII Address for enet1 */
+#define  SSB_SPROM1_ETHPHY_ET1A_SHIFT	5
+#define  SSB_SPROM1_ETHPHY_ET0M		(1<<14)	/* MDIO for enet0 */
+#define  SSB_SPROM1_ETHPHY_ET1M		(1<<15)	/* MDIO for enet1 */
+#define SSB_SPROM1_BINF			0x105C	/* Board info */
+#define  SSB_SPROM1_BINF_BREV		0x00FF	/* Board Revision */
+#define  SSB_SPROM1_BINF_CCODE		0x0F00	/* Country Code */
+#define  SSB_SPROM1_BINF_CCODE_SHIFT	8
+#define  SSB_SPROM1_BINF_ANTA		0x3000	/* Available A-PHY antennas */
+#define  SSB_SPROM1_BINF_ANTA_SHIFT	12
+#define  SSB_SPROM1_BINF_ANTBG		0xC000	/* Available B-PHY antennas */
+#define  SSB_SPROM1_BINF_ANTBG_SHIFT	14
+#define SSB_SPROM1_PA0B0		0x105E
+#define SSB_SPROM1_PA0B1		0x1060
+#define SSB_SPROM1_PA0B2		0x1062
+#define SSB_SPROM1_GPIOA		0x1064	/* General Purpose IO pins 0 and 1 */
+#define  SSB_SPROM1_GPIOA_P0		0x00FF	/* Pin 0 */
+#define  SSB_SPROM1_GPIOA_P1		0xFF00	/* Pin 1 */
+#define  SSB_SPROM1_GPIOA_P1_SHIFT	8
+#define SSB_SPROM1_GPIOB		0x1066	/* General Purpuse IO pins 2 and 3 */
+#define  SSB_SPROM1_GPIOB_P2		0x00FF	/* Pin 2 */
+#define  SSB_SPROM1_GPIOB_P3		0xFF00	/* Pin 3 */
+#define  SSB_SPROM1_GPIOB_P3_SHIFT	8
+#define SSB_SPROM1_MAXPWR		0x1068	/* Power Amplifier Max Power */
+#define  SSB_SPROM1_MAXPWR_BG		0x00FF	/* B-PHY and G-PHY (in dBm Q5.2) */
+#define  SSB_SPROM1_MAXPWR_A		0xFF00	/* A-PHY (in dBm Q5.2) */
+#define  SSB_SPROM1_MAXPWR_A_SHIFT	8
+#define SSB_SPROM1_PA1B0		0x106A
+#define SSB_SPROM1_PA1B1		0x106C
+#define SSB_SPROM1_PA1B2		0x106E
+#define SSB_SPROM1_ITSSI		0x1070	/* Idle TSSI Target */
+#define  SSB_SPROM1_ITSSI_BG		0x00FF	/* B-PHY and G-PHY*/
+#define  SSB_SPROM1_ITSSI_A		0xFF00	/* A-PHY */
+#define  SSB_SPROM1_ITSSI_A_SHIFT	8
+#define SSB_SPROM1_BFLLO		0x1072	/* Boardflags (low 16 bits) */
+#define SSB_SPROM1_AGAIN		0x1074	/* Antenna Gain (in dBm Q5.2) */
+#define  SSB_SPROM1_AGAIN_A		0x00FF	/* A-PHY */
+#define  SSB_SPROM1_AGAIN_BG		0xFF00	/* B-PHY and G-PHY */
+#define  SSB_SPROM1_AGAIN_BG_SHIFT	8
+#define SSB_SPROM1_OEM			0x1076	/* 8 bytes OEM string (rev 1 only) */
+/* SPROM Revision 2 (inherits from rev 1) */
+#define SSB_SPROM2_BFLHI		0x1038	/* Boardflags (high 16 bits) */
+#define SSB_SPROM2_MAXP_A		0x103A	/* A-PHY Max Power */
+#define  SSB_SPROM2_MAXP_A_HI		0x00FF	/* Max Power High */
+#define  SSB_SPROM2_MAXP_A_LO		0xFF00	/* Max Power Low */
+#define  SSB_SPROM2_MAXP_A_LO_SHIFT	8
+#define SSB_SPROM2_PA1LOB0		0x103C	/* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1LOB1		0x103E	/* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1LOB2		0x1040	/* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1HIB0		0x1042	/* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_PA1HIB1		0x1044	/* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_PA1HIB2		0x1046	/* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_OPO			0x1078	/* OFDM Power Offset from CCK Level */
+#define  SSB_SPROM2_OPO_VALUE		0x00FF
+#define  SSB_SPROM2_OPO_UNUSED		0xFF00
+#define SSB_SPROM2_CCODE		0x107C	/* Two char Country Code */
+/* SPROM Revision 3 (inherits from rev 2) */
+#define SSB_SPROM3_OFDMAPO		0x102C	/* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMALPO		0x1030	/* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMAHPO		0x1034	/* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_GPIOLDC		0x1042	/* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
+#define  SSB_SPROM3_GPIOLDC_OFF		0x0000FF00	/* Off Count */
+#define  SSB_SPROM3_GPIOLDC_OFF_SHIFT	8
+#define  SSB_SPROM3_GPIOLDC_ON		0x00FF0000	/* On Count */
+#define  SSB_SPROM3_GPIOLDC_ON_SHIFT	16
+#define SSB_SPROM3_CCKPO		0x1078	/* CCK Power Offset */
+#define  SSB_SPROM3_CCKPO_1M		0x000F	/* 1M Rate PO */
+#define  SSB_SPROM3_CCKPO_2M		0x00F0	/* 2M Rate PO */
+#define  SSB_SPROM3_CCKPO_2M_SHIFT	4
+#define  SSB_SPROM3_CCKPO_55M		0x0F00	/* 5.5M Rate PO */
+#define  SSB_SPROM3_CCKPO_55M_SHIFT	8
+#define  SSB_SPROM3_CCKPO_11M		0xF000	/* 11M Rate PO */
+#define  SSB_SPROM3_CCKPO_11M_SHIFT	12
+#define  SSB_SPROM3_OFDMGPO		0x107A	/* G-PHY OFDM Power Offset (4 bytes, BigEndian) */
+
+/* Values for SSB_SPROM1_BINF_CCODE */
+enum {
+	SSB_SPROM1CCODE_WORLD = 0,
+	SSB_SPROM1CCODE_THAILAND,
+	SSB_SPROM1CCODE_ISRAEL,
+	SSB_SPROM1CCODE_JORDAN,
+	SSB_SPROM1CCODE_CHINA,
+	SSB_SPROM1CCODE_JAPAN,
+	SSB_SPROM1CCODE_USA_CANADA_ANZ,
+	SSB_SPROM1CCODE_EUROPE,
+	SSB_SPROM1CCODE_USA_LOW,
+	SSB_SPROM1CCODE_JAPAN_HIGH,
+	SSB_SPROM1CCODE_ALL,
+	SSB_SPROM1CCODE_NONE,
+};
+
+/* Address-Match values and masks (SSB_ADMATCHxxx) */
+#define SSB_ADM_TYPE			0x00000003	/* Address type */
+#define  SSB_ADM_TYPE0			0
+#define  SSB_ADM_TYPE1			1
+#define  SSB_ADM_TYPE2			2
+#define SSB_ADM_AD64			0x00000004
+#define SSB_ADM_SZ0			0x000000F8	/* Type0 size */
+#define SSB_ADM_SZ0_SHIFT		3
+#define SSB_ADM_SZ1			0x000001F8	/* Type1 size */
+#define SSB_ADM_SZ1_SHIFT		3
+#define SSB_ADM_SZ2			0x000001F8	/* Type2 size */
+#define SSB_ADM_SZ2_SHIFT		3
+#define SSB_ADM_EN			0x00000400	/* Enable */
+#define SSB_ADM_NEG			0x00000800	/* Negative decode */
+#define SSB_ADM_BASE0			0xFFFFFF00	/* Type0 base address */
+#define SSB_ADM_BASE0_SHIFT		8
+#define SSB_ADM_BASE1			0xFFFFF000	/* Type1 base address for the core */
+#define SSB_ADM_BASE1_SHIFT		12
+#define SSB_ADM_BASE2			0xFFFF0000	/* Type2 base address for the core */
+#define SSB_ADM_BASE2_SHIFT		16
+
+
+#endif /* LINUX_SSB_REGS_H_ */
diff --git a/MAINTAINERS b/MAINTAINERS
index 845fbf4..aee5182 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3298,6 +3347,12 @@
 L:	[email protected]
 S:	Maintained
 
+SONICS SILICON BACKPLANE DRIVER (SSB)
+P:	Michael Buesch
+M:	[email protected]
+L:	[email protected]
+S:	Maintained
+
 SONY VAIO CONTROL DEVICE DRIVER
 P:	Mattia Dongili
 M:	[email protected]

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux