sorry for the long delay in testing.
On Wed, 27 Jun 2007, Randy Dunlap wrote:
[adding [email protected]]
On Wed, 27 Jun 2007 00:38:17 -0700 (PDT) [email protected] wrote:
On Tue, 26 Jun 2007, Randy Dunlap wrote:
On Mon, 25 Jun 2007 15:56:17 -0700 (PDT) [email protected] wrote:
due to the size the files are posted at http://linux.lang.hm/linux
let me know what else I can send to help.
David Lang
I suggest that you test 2.6.22-rcN using one or both of these
boot options:
noisapnp
pnpacpi=off
Somewhere between 2.6.18 and 2.6.22-development, the ACPI config
symbol also starting enabling (selecting) PNP. That's one of many
differences....
with the 2.6.22-rc4 kernel that I was useing earlier, adding these two
options clears up the problem. Thanks.
should I test the two individually? or just plan on useing both from now
on?
Yes, please test them individually. I expect that just one of them
will suffice, but I don't know which one.
pnpacpi=off works
noisapnp doesn't work
I normally disable PnP (both ISA and PCI), should I leave it enabled with
the newer kernels and this motherboard?
ACPI recently began enabling (selecting) PNP for you...
I didn't realize this had changed.
How do you normally disable PCI PNP?
What kind of hardware is this? Please show us lspci output.
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Capabilities: [e0] HyperTransport: MSI Mapping
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: 66MHz, fast devsel, IRQ 3
I/O ports at fc00 [size=32]
I/O ports at 1c00 [size=64]
I/O ports at 1c40 [size=64]
Capabilities: [44] Power Management version 2
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 3
I/O ports at f000 [size=256]
I/O ports at ec00 [size=256]
Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at e000 [size=16]
Capabilities: [44] Power Management version 2
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: fdf00000-fdffffff
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
Subsystem: Elitegroup Computer Systems Unknown device 1b51
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
I/O ports at dc00 [size=8]
Capabilities: [44] Power Management version 2
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdc00000
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fda00000
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fd900000-fd9fffff
Prefetchable memory behind bridge: 00000000fd800000-00000000fd800000
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: fd700000-fd7fffff
Prefetchable memory behind bridge: 00000000fa000000-00000000fbf00000
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: [80] HyperTransport: Host or Secondary Interface
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
01:06.0 RAID bus controller: 3ware Inc 5xxx/6xxx-series PATA-RAID (rev 12)
Subsystem: 3ware Inc 5xxx/6xxx-series PATA-RAID
Flags: bus master, stepping, medium devsel, latency 32, IRQ 16
I/O ports at cc00 [size=16]
[virtual] Expansion ROM at fdf20000 [disabled] [size=64K]
01:07.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
BIST result: 00
I/O ports at c800 [disabled] [size=256]
Memory at fdeff000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at fdf00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
01:08.0 RAID bus controller: 3ware Inc 5xxx/6xxx-series PATA-RAID (rev 12)
Subsystem: 3ware Inc 5xxx/6xxx-series PATA-RAID
Flags: bus master, stepping, medium devsel, latency 32, IRQ 18
I/O ports at c400 [size=16]
[virtual] Expansion ROM at fdf30000 [disabled] [size=64K]
05:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon X300 (PCIE)] (prog-if 00 [VGA])
Subsystem: Diamond Multimedia Systems Unknown device 0460
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at fa000000 (32-bit, prefetchable) [size=32M]
I/O ports at 8c00 [size=256]
Memory at fd7f0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fd700000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Express Endpoint IRQ 0
Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Capabilities: [100] Advanced Error Reporting
05:00.1 Display controller: ATI Technologies Inc RV370 [Radeon X300SE]
Subsystem: Diamond Multimedia Systems Unknown device 0461
Flags: fast devsel
Memory at fd7e0000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Express Endpoint IRQ 0
David Lang
I would also disable CONFIG_USB_USS720, at least for testing.
for ease of testing (I got time to reboot the box around midnight) I used
the same config as before, so this is still on.
David Lang
On Mon, 25 Jun 2007, Randy Dunlap wrote:
Date: Mon, 25 Jun 2007 15:40:28 -0700
From: Randy Dunlap <[email protected]>
To: [email protected]
Cc: Andrew Morton <[email protected]>, [email protected],
[email protected]
Subject: Re: long-term regression
[email protected] wrote:
On Thu, 21 Jun 2007, Randy Dunlap wrote:
Date: Thu, 21 Jun 2007 08:36:59 -0700
From: Randy Dunlap <[email protected]>
To: Andrew Morton <[email protected]>
Cc: [email protected], [email protected],
[email protected]
Subject: Re: long-term regression
On Thu, 21 Jun 2007 05:28:07 -0700 Andrew Morton wrote:
On Sun, 17 Jun 2007 10:57:55 -0700 (PDT) [email protected] wrote:
I haven't had time to bisect this, but I'm having a problem on a
AMD64
gentoo system where the printer doesn't work with recent kernels.
2.6.18-rc3 worked
2.6.21.1 doesn't
2.6.22-rc4 doesn't
unfortunantly the system is gooted on 2.6.18 at the moment and I'm
out of
town so my ability to test is limited I can provide the 2.6.22-rc4
(attached) and 2.6.18-rc3 configs.
dmesg appears to show the port being detected, but writes to the
port
under newer kernels appear to complete, but no data gets to the
printer.
any suggestions other then doing the large bisect?
That would be good, thanks. Please be sure to cc linux-usb-devel on
the results.
OK, I'm curious about how someone deduced that this is a problem
with a USB printer vs. parallel port printer since the config file has:
CONFIG_PRINTER=y
CONFIG_USB_PRINTER=y
The kernel boot log should probably be posted also.
here is the dmesg from 2.6.22-rc4 and kern.log showing 2.6.22.-rc4 and
2.6.180rc3
the printer not working is the parallel port.
This email didn't show up on lkml or linux-usb-devel due to size limits (it
was 900+ KB).
David, please send your working 2.6.18 config file.
Can you post the kernel log files on the web somewhere?
---
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
