Re: [PATCH 1/5] Add the explanation and sample of RapidIO DTS sector to the document of booting-without-of.txt file.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



+    - device_type : Should be "rapidio"

There is no OF binding, so no.

So, we need to define it.

If you want to.  Until that has been done, don't use
a "device_type".  Linux won't use it, anyway.

+    - compatible : Should be "fsl,rapidio-v0.0" or
"fsl,rapidio-v1.0"
+      and so on. The version number is got from IP Block Revision
+      Register of RapidIO controller.

It's better to use real device names, just like everyone
else.

Some silicons of Freescale processor are the same RapidIO controller,
such as mpc8540/mpc8560 are the same (v0.0), mpc8548/mpc8641 are the
same (v1.0). For v1.0 RapidIO controller, should we use mpc8548 or
mpc8641? Those will make people confused.

Not at all.  On an 8641 it could be

	compatible = "fsl,mpc8641-rapidio" "fsl,mpc8548-rapidio";

which states "this is the 8641 thing and it is compatible
to the 8548 thing".  Perfectly clear.

Using IP Block Revision is a
clear choice.

I don't think so.  For one thing, it describes a version of
a cell design, not a version of an actual device.  For another
thing, if I hear "8641" I know what you're talking about (sort
of, anyway), but I draw a blank stare if you say "v1.0".  I'm
sure I'm not the only one.  Concrete names are good.

+    - #address-cells : Address representation for
"rapidio" devices.
+      This field represents the number of cells needed to represent
+      the RapidIO address of the registers.  For
supporting more than
+      36-bits RapidIO address, this field should be <2>.

More than 32 bit?

Yes, RapidIO bus address width is 34 bits.

You said "more than 36 bit", I tried to ask if that is a typo
perhaps.

No.  The format of an "interrupts" entry is defined by
the interrupt domain this device sits in, not by the
device itself.

Do you misunderstand the meaning of 'interrupts'?

Hahaha.  No, I don't misunderstand what the "interrupts" property
means.  Perhaps you do?

These interrupts is
issued from the RapidIO controller to the pic controller for tx, rx,
err, doorbell and message.

But the rapidio node doesn't know or care what the interrupts
are connected to, and neither should it.  That's what the
interrupt mapping recommended practice is for.

For this sector, interrupts order should be
+      <err_irq bell_outb_irq bell_inb_irq msg1_tx_irq msg1_rx_irq
+      msg2_tx_irq msg2_rx_irq ... msgN_tx_irq msgN_rx_irq>.

That's to be defined in the binding for your specific device,
not in a more generic rapidio binding.

These description is just for compatible="fsl,rapidio-v*.*" rapidio
controller.

Okay, good.  Please make that way more obvious then :-)

+		#address-cells = <2>;

You want a #size-cells as well.

The size is not used in this sector, so no defined.

The size _is_ used; in the "ranges" property in this node,
for example.  It is also needed to describe the "reg" for
any child node of this node.

A non-existant "#size-cells" means 1, and "#address-cells"
means 2, so in principle you could do without these
properties; but Linux doesn't parse the tree correctly in
that case (which reminds me, I have some more patches to
send).

Thanks!

My pleasure,


Segher

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux