On Thu, 7 Jun 2007, Jesse Barnes wrote:
On some machines, buggy BIOSes don't properly setup WB MTRRs to
cover all available RAM, meaning the last few megs (or even gigs)
of memory will be marked uncached. Since Linux tends to allocate
from high memory addresses first, this causes the machine to be
unusably slow as soon as the kernel starts really using memory
(i.e. right around init time).
This patch works around the problem by scanning the MTRRs at
boot and figuring out whether the current end_pfn value (setup
by early e820 code) goes beyond the highest WB MTRR range, and
if so, trimming it to match. A fairly obnoxious KERN_WARNING
is printed too, letting the user know that not all of their
memory is available due to a likely BIOS bug.
Something similar could be done on i386 if needed, but the boot
ordering would be slightly different, since the MTRR code on i386
depends on the boot_cpu_data structure being setup.
This patch incorporates the feedback from Eric and Andi:
- use MAX_VAR_RANGES instead of NUM_VAR_RANGES
- move array declaration to header file as an extern
- add command line disable option "disable_mtrr_trim"
- don't run the trim code if the MTRR default type is cacheable
- don't run the trim code on non-Intel machines
Justin, feel free to test again if you have time and add your
"Tested-by" signoff.
Andi, as for large pages, do you think this is ok as is, or should
I trim a larger granularity? If so, what granularity?
Signed-off-by: Jesse Barnes <[email protected]>
Thanks,
Jesse
v1 of your patch:
top - 18:53:46 up 1 day, 1 min, 27 users, load average: 2.82, 1.11,
0.90
Tasks: 356 total, 7 running, 348 sleeping, 1 stopped, 0 zombie
Cpu(s): 2.2%us, 0.4%sy, 0.0%ni, 97.0%id, 0.1%wa, 0.0%hi, 0.2%si,
0.0%st
Mem: 8039576k total, 7962376k used, 77200k free, 716k buffers
Swap: 16787768k total, 128k used, 16787640k free, 6713332k cached
v2 of your patch: (dmesg also attached)
top - 18:58:59 up 2 min, 4 users, load average: 0.12, 0.13, 0.05
Tasks: 155 total, 1 running, 154 sleeping, 0 stopped, 0 zombie
Cpu(s): 2.0%us, 1.1%sy, 0.5%ni, 94.8%id, 1.5%wa, 0.0%hi, 0.0%si,
0.0%st
Mem: 8039576k total, 982192k used, 7057384k free, 1876k buffers
Swap: 16787768k total, 0k used, 16787768k free, 114492k cached
If the box has no issues over the next 8 hours with me pounding it with
backups, bzip2s etc I'll consider it good, so far it boots fine etc, no
issues, but I'll let it cook for a bit. Will update tomorrow.
Thanks,
Justin.
[ 0.000000] Linux version 2.6.22-rc4 ([email protected]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #4 SMP Thu Jun 7 18:54:18 EDT 2007
[ 0.000000] Command line: auto BOOT_IMAGE=2.6.22-rc4-4 ro root=902 [email protected]/eth0,[email protected]/00:50:8D:ED:3C:E7
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cf58f000 (usable)
[ 0.000000] BIOS-e820: 00000000cf58f000 - 00000000cf59c000 (reserved)
[ 0.000000] BIOS-e820: 00000000cf59c000 - 00000000cf653000 (usable)
[ 0.000000] BIOS-e820: 00000000cf653000 - 00000000cf6a5000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cf6a5000 - 00000000cf6a8000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cf6a8000 - 00000000cf6ef000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cf6ef000 - 00000000cf6f1000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cf6f1000 - 00000000cf6f2000 (usable)
[ 0.000000] BIOS-e820: 00000000cf6f2000 - 00000000cf6ff000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cf6ff000 - 00000000cf700000 (usable)
[ 0.000000] BIOS-e820: 00000000cf700000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000022c000000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 143) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 849295) 1 entries of 256 used
[ 0.000000] Entering add_active_range(0, 849308, 849491) 2 entries of 256 used
[ 0.000000] Entering add_active_range(0, 849649, 849650) 3 entries of 256 used
[ 0.000000] Entering add_active_range(0, 849663, 849664) 4 entries of 256 used
[ 0.000000] Entering add_active_range(0, 1048576, 2277376) 5 entries of 256 used
[ 0.000000] end_pfn_map = 2277376
[ 0.000000] ***************
[ 0.000000] **** WARNING: likely BIOS bug
[ 0.000000] **** MTRRs don't cover all of memory, trimmed 16384 pages
[ 0.000000] ***************
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL )
[ 0.000000] ACPI: RSDT CF6FD038, 0050 (r1 INTEL DG965WH 64C 1000013)
[ 0.000000] ACPI: FACP CF6FC000, 0074 (r1 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: DSDT CF6F7000, 40E9 (r1 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: FACS CF6A8000, 0040
[ 0.000000] ACPI: APIC CF6F6000, 0078 (r1 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: WDDT CF6F5000, 0040 (r1 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: MCFG CF6F4000, 003C (r1 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: ASF! CF6F3000, 00A6 (r32 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: HPET CF6F2000, 0038 (r1 INTEL DG965WH 64C MSFT 1000013)
[ 0.000000] ACPI: SSDT CF6F0000, 01BC (r1 INTEL CpuPm 64C MSFT 1000013)
[ 0.000000] ACPI: SSDT CF6EF000, 0175 (r1 INTEL Cpu0Ist 64C MSFT 1000013)
[ 0.000000] ACPI: SSDT CF6A7000, 0175 (r1 INTEL Cpu1Ist 64C MSFT 1000013)
[ 0.000000] ACPI: SSDT CF6A6000, 0175 (r1 INTEL Cpu2Ist 64C MSFT 1000013)
[ 0.000000] ACPI: SSDT CF6A5000, 0175 (r1 INTEL Cpu3Ist 64C MSFT 1000013)
[ 0.000000] Entering add_active_range(0, 0, 143) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 256, 849295) 1 entries of 256 used
[ 0.000000] Entering add_active_range(0, 849308, 849491) 2 entries of 256 used
[ 0.000000] Entering add_active_range(0, 849649, 849650) 3 entries of 256 used
[ 0.000000] Entering add_active_range(0, 849663, 849664) 4 entries of 256 used
[ 0.000000] Entering add_active_range(0, 1048576, 2260992) 5 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 2260992
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0 -> 143
[ 0.000000] 0: 256 -> 849295
[ 0.000000] 0: 849308 -> 849491
[ 0.000000] 0: 849649 -> 849650
[ 0.000000] 0: 849663 -> 849664
[ 0.000000] 0: 1048576 -> 2260992
[ 0.000000] On node 0 totalpages: 2061783
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1395 pages reserved
[ 0.000000] DMA zone: 2532 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 831104 pages, LIFO batch:31
[ 0.000000] Normal zone: 16576 pages used for memmap
[ 0.000000] Normal zone: 1195840 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] Processor #2
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] Processor #3
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ff00000)
[ 0.000000] PERCPU: Allocating 24744 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 2029476
[ 0.000000] Kernel command line: auto BOOT_IMAGE=2.6.22-rc4-4 ro root=902 [email protected]/eth0,[email protected]/00:50:8D:ED:3C:E7
[ 0.000000] netconsole: local port 4444
[ 0.000000] netconsole: local IP 192.168.168.253
[ 0.000000] netconsole: interface eth0
[ 0.000000] netconsole: remote port 514
[ 0.000000] netconsole: remote IP 192.168.168.254
[ 0.000000] netconsole: remote ethernet address 00:50:8d:ed:3c:e7
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 48.130591] time.c: Detected 2397.606 MHz processor.
[ 48.131666] Console: colour VGA+ 80x25
[ 48.139532] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 48.145756] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 48.146855] Checking aperture...
[ 48.146909] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 48.186683] Placing software IO TLB between 0x951a000 - 0xd51a000
[ 48.256438] Memory: 8039012k/9043968k available (3549k kernel code, 207808k reserved, 1317k data, 216k init)
[ 48.315841] Calibrating delay using timer specific routine.. 4797.71 BogoMIPS (lpj=2398858)
[ 48.315963] Mount-cache hash table entries: 256
[ 48.316090] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 48.316152] CPU: L2 cache: 4096K
[ 48.316192] using mwait in idle threads.
[ 48.316234] CPU: Physical Processor ID: 0
[ 48.316275] CPU: Processor Core ID: 0
[ 48.316320] CPU0: Thermal monitoring enabled (TM2)
[ 48.316367] Freeing SMP alternatives: 33k freed
[ 48.316433] ACPI: Core revision 20070126
[ 48.329824] Using local APIC timer interrupts.
[ 48.371568] result 16650025
[ 48.371607] Detected 16.650 MHz APIC timer.
[ 48.371903] Booting processor 1/4 APIC 0x2
[ 48.382292] Initializing CPU#1
[ 48.442807] Calibrating delay using timer specific routine.. 4795.14 BogoMIPS (lpj=2397570)
[ 48.442814] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 48.442816] CPU: L2 cache: 4096K
[ 48.442818] CPU: Physical Processor ID: 0
[ 48.442819] CPU: Processor Core ID: 2
[ 48.442824] CPU1: Thermal monitoring enabled (TM2)
[ 48.443247] Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07
[ 48.443310] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 48.463868] Booting processor 2/4 APIC 0x1
[ 48.474628] Initializing CPU#2
[ 48.534787] Calibrating delay using timer specific routine.. 4795.30 BogoMIPS (lpj=2397650)
[ 48.534793] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 48.534794] CPU: L2 cache: 4096K
[ 48.534796] CPU: Physical Processor ID: 0
[ 48.534797] CPU: Processor Core ID: 1
[ 48.534802] CPU2: Thermal monitoring enabled (TM2)
[ 48.535246] Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07
[ 48.535273] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 48.555867] Booting processor 3/4 APIC 0x3
[ 48.566258] Initializing CPU#3
[ 48.626765] Calibrating delay using timer specific routine.. 4795.21 BogoMIPS (lpj=2397608)
[ 48.626771] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 48.626773] CPU: L2 cache: 4096K
[ 48.626775] CPU: Physical Processor ID: 0
[ 48.626776] CPU: Processor Core ID: 3
[ 48.626782] CPU3: Thermal monitoring enabled (TM2)
[ 48.627204] Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07
[ 48.627274] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 48.647766] Brought up 4 CPUs
[ 49.290497] migration_cost=26,3427
[ 49.290867] NET: Registered protocol family 16
[ 49.290968] ACPI: bus type pci registered
[ 49.291017] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
[ 49.291064] PCI: Not using MMCONFIG.
[ 49.291105] PCI: Using configuration type 1
[ 49.293817] ACPI: Interpreter enabled
[ 49.293859] ACPI: Using IOAPIC for interrupt routing
[ 49.297371] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 49.297430] PCI: Probing PCI hardware (bus 00)
[ 49.298083] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 49.298132] PCI quirk: region 0500-053f claimed by ICH6 GPIO
[ 49.299041] PCI: Transparent bridge - 0000:00:1e.0
[ 49.299139] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 49.299405] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 49.299607] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 49.299689] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[ 49.299768] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
[ 49.299848] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[ 49.299927] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 49.303177] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 49.303465] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
[ 49.303754] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 49.304060] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 49.304364] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11 12)
[ 49.304653] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[ 49.304938] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
[ 49.305263] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[ 49.305553] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 49.305604] pnp: PnP ACPI init
[ 49.305650] ACPI: bus type pnp registered
[ 49.307458] pnp: PnP ACPI: found 12 devices
[ 49.307500] ACPI: ACPI bus type pnp unregistered
[ 49.307664] SCSI subsystem initialized
[ 49.307760] libata version 2.21 loaded.
[ 49.307814] usbcore: registered new interface driver usbfs
[ 49.307881] usbcore: registered new interface driver hub
[ 49.307950] usbcore: registered new device driver usb
[ 49.308022] PCI: Using ACPI for IRQ routing
[ 49.308064] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 49.308236] PCI-GART: No AMD northbridge found.
[ 49.308281] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 49.308415] hpet0: 3 64-bit timers, 14318180 Hz
[ 49.309523] pnp: 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved
[ 49.309573] pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
[ 49.309622] Time: tsc clocksource has been installed.
[ 49.309667] pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 49.309715] pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 49.309768] pnp: 00:06: ioport range 0x500-0x53f has been reserved
[ 49.309814] pnp: 00:06: ioport range 0x400-0x47f has been reserved
[ 49.310422] pnp: 00:06: ioport range 0x680-0x6ff has been reserved
[ 49.310738] ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 49.360956] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0084000-e00847ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 49.361085] PCI: Bridge: 0000:00:1c.0
[ 49.361125] IO window: disabled.
[ 49.361168] MEM window: e0700000-e07fffff
[ 49.361211] PREFETCH window: disabled.
[ 49.361275] PCI: Bridge: 0000:00:1c.1
[ 49.361317] IO window: 5000-5fff
[ 49.361359] MEM window: e0400000-e04fffff
[ 49.361413] PREFETCH window: disabled.
[ 49.361466] PCI: Bridge: 0000:00:1c.2
[ 49.361508] IO window: 4000-4fff
[ 49.361552] MEM window: e0300000-e03fffff
[ 49.361597] PREFETCH window: e0800000-e08fffff
[ 49.361643] PCI: Bridge: 0000:00:1c.3
[ 49.361684] IO window: 3000-3fff
[ 49.361726] MEM window: e0200000-e02fffff
[ 49.361770] PREFETCH window: e0900000-e09fffff
[ 49.361815] PCI: Bridge: 0000:00:1c.4
[ 49.361857] IO window: 2000-2fff
[ 49.361899] MEM window: e0100000-e01fffff
[ 49.361943] PREFETCH window: e0a00000-e0afffff
[ 49.361988] PCI: Bridge: 0000:00:1e.0
[ 49.362030] IO window: 1000-1fff
[ 49.362072] MEM window: e0000000-e00fffff
[ 49.362116] PREFETCH window: e0b00000-e0bfffff
[ 49.362172] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 49.362256] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 49.362280] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 49.362373] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 49.362386] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 49.362490] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 49.362502] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 49.362586] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 49.362600] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
[ 49.362683] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 49.362691] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 49.362739] NET: Registered protocol family 2
[ 49.371587] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 49.372107] TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
[ 49.373400] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 49.373900] TCP: Hash tables configured (established 131072 bind 65536)
[ 49.373948] TCP reno registered
[ 49.377996] Installing knfsd (copyright (C) 1996 [email protected]).
[ 49.378132] SGI XFS with large block/inode numbers, no debug enabled
[ 49.378483] io scheduler noop registered
[ 49.378525] io scheduler anticipatory registered (default)
[ 49.378575] Boot video device is 0000:00:02.0
[ 49.379026] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 49.379058] assign_interrupt_mode Found MSI capability
[ 49.379129] Allocate Port Service[0000:00:1c.0:pcie00]
[ 49.379177] Allocate Port Service[0000:00:1c.0:pcie02]
[ 49.379263] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 49.379294] assign_interrupt_mode Found MSI capability
[ 49.379362] Allocate Port Service[0000:00:1c.1:pcie00]
[ 49.379410] Allocate Port Service[0000:00:1c.1:pcie02]
[ 49.379494] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 49.379525] assign_interrupt_mode Found MSI capability
[ 49.379603] Allocate Port Service[0000:00:1c.2:pcie00]
[ 49.379638] Allocate Port Service[0000:00:1c.2:pcie02]
[ 49.379725] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 49.379763] assign_interrupt_mode Found MSI capability
[ 49.379838] Allocate Port Service[0000:00:1c.3:pcie00]
[ 49.379873] Allocate Port Service[0000:00:1c.3:pcie02]
[ 49.379960] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 49.379996] assign_interrupt_mode Found MSI capability
[ 49.380073] Allocate Port Service[0000:00:1c.4:pcie00]
[ 49.380133] Allocate Port Service[0000:00:1c.4:pcie02]
[ 49.382757] lp: driver loaded but no devices found
[ 49.382849] Real Time Clock Driver v1.12ac
[ 49.383002] hpet_resources: 0xfed00000 is busy
[ 49.383012] Linux agpgart interface v0.102 (c) Dave Jones
[ 49.383135] agpgart: Detected an Intel 965G Chipset.
[ 49.384311] agpgart: Detected 7676K stolen memory.
[ 49.396970] agpgart: AGP aperture is 256M @ 0xd0000000
[ 49.397047] [drm] Initialized drm 1.1.0 20060810
[ 49.397105] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 49.397255] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 49.397396] parport_pc 00:07: reported by Plug and Play ACPI
[ 49.397520] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 49.479882] lp0: using parport0 (interrupt-driven).
[ 49.480096] loop: module loaded
[ 49.480139] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 49.480188] Copyright (c) 1999-2006 Intel Corporation.
[ 49.480275] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 49.480369] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 49.497933] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:6e:9d:43
[ 49.573213] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 49.573300] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 49.834558] e1000: 0000:06:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:00:cd:b1
[ 49.981554] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 49.981615] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 50.228621] e1000: 0000:06:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:29:37:db
[ 50.255346] e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 50.255480] netconsole: device eth0 not up yet, forcing it
[ 50.617119] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090270001c5be9f]
[ 52.334278] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 52.358716] netconsole: network logging started
[ 52.358929] ahci 0000:00:1f.2: version 2.2
[ 52.358946] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 53.359807] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 53.359880] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 53.359936] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 53.360168] scsi0 : ahci
[ 53.360286] scsi1 : ahci
[ 53.360386] scsi2 : ahci
[ 53.360487] scsi3 : ahci
[ 53.360585] scsi4 : ahci
[ 53.360700] scsi5 : ahci
[ 53.360795] ata1: SATA max UDMA/133 cmd 0xffffc2000002e100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 53.360874] ata2: SATA max UDMA/133 cmd 0xffffc2000002e180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 53.360952] ata3: SATA max UDMA/133 cmd 0xffffc2000002e200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 53.361030] ata4: SATA max UDMA/133 cmd 0xffffc2000002e280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 53.361108] ata5: SATA max UDMA/133 cmd 0xffffc2000002e300 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 53.361205] ata6: SATA max UDMA/133 cmd 0xffffc2000002e380 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 53.820558] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 53.823973] ata1.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
[ 53.824043] ata1.00: ATA-6: WDC WD740GD-00FLC0, 33.08F33, max UDMA/133
[ 53.824098] ata1.00: 145226112 sectors, multi 0: LBA48
[ 53.828532] ata1.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
[ 53.828605] ata1.00: configured for UDMA/133
[ 54.286854] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 54.290267] ata2.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
[ 54.290337] ata2.00: ATA-6: WDC WD740GD-00FLC0, 33.08F33, max UDMA/133
[ 54.290391] ata2.00: 145226112 sectors, multi 0: LBA48
[ 54.294838] ata2.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
[ 54.294909] ata2.00: configured for UDMA/133
[ 54.755252] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 54.757454] ata3.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 54.757534] ata3.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 54.757606] ata3.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 54.760453] ata3.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 54.760525] ata3.00: configured for UDMA/133
[ 55.219479] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 55.221656] ata4.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 55.221727] ata4.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 55.221783] ata4.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 55.224617] ata4.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 55.224689] ata4.00: configured for UDMA/133
[ 55.682687] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 55.684748] ata5.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 55.684819] ata5.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 55.684874] ata5.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 55.687539] ata5.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 55.687611] ata5.00: configured for UDMA/133
[ 56.146925] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 56.148986] ata6.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 56.149058] ata6.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 56.149113] ata6.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 56.151795] ata6.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 56.151867] ata6.00: configured for UDMA/133
[ 56.151994] scsi 0:0:0:0: Direct-Access ATA WDC WD740GD-00FL 33.0 PQ: 0 ANSI: 5
[ 56.152166] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
[ 56.152223] sd 0:0:0:0: [sda] Write Protect is off
[ 56.152279] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 56.152290] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.152401] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
[ 56.152468] sd 0:0:0:0: [sda] Write Protect is off
[ 56.152524] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 56.152534] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.152616] sda: sda1 sda2 sda3
[ 56.163015] sd 0:0:0:0: [sda] Attached SCSI disk
[ 56.163184] scsi 1:0:0:0: Direct-Access ATA WDC WD740GD-00FL 33.0 PQ: 0 ANSI: 5
[ 56.163310] sd 1:0:0:0: [sdb] 145226112 512-byte hardware sectors (74356 MB)
[ 56.163367] sd 1:0:0:0: [sdb] Write Protect is off
[ 56.163414] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 56.163425] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.163531] sd 1:0:0:0: [sdb] 145226112 512-byte hardware sectors (74356 MB)
[ 56.163596] sd 1:0:0:0: [sdb] Write Protect is off
[ 56.163643] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 56.163656] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.163744] sdb: sdb1 sdb2 sdb3
[ 56.167415] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 56.167520] scsi 2:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 56.167651] sd 2:0:0:0: [sdc] 293046768 512-byte hardware sectors (150040 MB)
[ 56.167713] sd 2:0:0:0: [sdc] Write Protect is off
[ 56.167760] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 56.167770] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.167880] sd 2:0:0:0: [sdc] 293046768 512-byte hardware sectors (150040 MB)
[ 56.167938] sd 2:0:0:0: [sdc] Write Protect is off
[ 56.167985] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 56.167995] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.168068] sdc: sdc1
[ 56.173303] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 56.173408] scsi 3:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 56.173528] sd 3:0:0:0: [sdd] 293046768 512-byte hardware sectors (150040 MB)
[ 56.173583] sd 3:0:0:0: [sdd] Write Protect is off
[ 56.173630] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 56.173640] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.173734] sd 3:0:0:0: [sdd] 293046768 512-byte hardware sectors (150040 MB)
[ 56.173788] sd 3:0:0:0: [sdd] Write Protect is off
[ 56.173855] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 56.173865] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.173936] sdd: sdd1
[ 56.182236] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 56.182379] scsi 4:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 56.182498] sd 4:0:0:0: [sde] 293046768 512-byte hardware sectors (150040 MB)
[ 56.182552] sd 4:0:0:0: [sde] Write Protect is off
[ 56.182599] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 56.182609] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.182704] sd 4:0:0:0: [sde] 293046768 512-byte hardware sectors (150040 MB)
[ 56.182758] sd 4:0:0:0: [sde] Write Protect is off
[ 56.182805] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 56.182815] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.182886] sde: sde1
[ 56.191616] sd 4:0:0:0: [sde] Attached SCSI disk
[ 56.191720] scsi 5:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 56.191835] sd 5:0:0:0: [sdf] 293046768 512-byte hardware sectors (150040 MB)
[ 56.191891] sd 5:0:0:0: [sdf] Write Protect is off
[ 56.191938] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 56.191949] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.192045] sd 5:0:0:0: [sdf] 293046768 512-byte hardware sectors (150040 MB)
[ 56.192099] sd 5:0:0:0: [sdf] Write Protect is off
[ 56.192146] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 56.192156] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 56.192248] sdf: sdf1
[ 56.200792] sd 5:0:0:0: [sdf] Attached SCSI disk
[ 56.200925] sata_sil24 0000:03:00.0: version 0.9
[ 56.200945] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 56.201098] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 56.201152] scsi6 : sata_sil24
[ 56.201229] scsi7 : sata_sil24
[ 56.201302] ata7: SATA max UDMA/100 cmd 0xffffc20000038000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 56.201375] ata8: SATA max UDMA/100 cmd 0xffffc2000003a000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 56.605136] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 56.607673] ata7.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 56.607744] ata7.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 56.607800] ata7.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 56.611033] ata7.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 56.611106] ata7.00: configured for UDMA/100
[ 57.015233] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 57.017747] ata8.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 57.017818] ata8.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 57.017875] ata8.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 57.021110] ata8.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 57.021182] ata8.00: configured for UDMA/100
[ 57.021288] scsi 6:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.021440] sd 6:0:0:0: [sdg] 293046768 512-byte hardware sectors (150040 MB)
[ 57.021507] sd 6:0:0:0: [sdg] Write Protect is off
[ 57.021554] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 57.021565] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.021678] sd 6:0:0:0: [sdg] 293046768 512-byte hardware sectors (150040 MB)
[ 57.021735] sd 6:0:0:0: [sdg] Write Protect is off
[ 57.021803] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 57.021813] sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.021885] sdg: sdg1
[ 57.029146] sd 6:0:0:0: [sdg] Attached SCSI disk
[ 57.029286] scsi 7:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.029404] sd 7:0:0:0: [sdh] 293046768 512-byte hardware sectors (150040 MB)
[ 57.029458] sd 7:0:0:0: [sdh] Write Protect is off
[ 57.029505] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 57.029516] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.029612] sd 7:0:0:0: [sdh] 293046768 512-byte hardware sectors (150040 MB)
[ 57.029666] sd 7:0:0:0: [sdh] Write Protect is off
[ 57.029713] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 57.029723] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.029816] sdh: sdh1
[ 57.037301] sd 7:0:0:0: [sdh] Attached SCSI disk
[ 57.037420] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 57.037567] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 57.037611] scsi8 : sata_sil24
[ 57.037687] scsi9 : sata_sil24
[ 57.037757] ata9: SATA max UDMA/100 cmd 0xffffc20000068000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 57.037832] ata10: SATA max UDMA/100 cmd 0xffffc2000006a000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 57.444772] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 57.446869] ata9.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 57.446940] ata9.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 57.447004] ata9.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 57.449754] ata9.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 57.449826] ata9.00: configured for UDMA/100
[ 57.854989] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 57.857111] ata10.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 57.857182] ata10.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 57.857256] ata10.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 57.860018] ata10.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 57.860092] ata10.00: configured for UDMA/100
[ 57.860198] scsi 8:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.860352] sd 8:0:0:0: [sdi] 293046768 512-byte hardware sectors (150040 MB)
[ 57.860406] sd 8:0:0:0: [sdi] Write Protect is off
[ 57.860453] sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 57.860464] sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.860574] sd 8:0:0:0: [sdi] 293046768 512-byte hardware sectors (150040 MB)
[ 57.860632] sd 8:0:0:0: [sdi] Write Protect is off
[ 57.860680] sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 57.860690] sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.860761] sdi: sdi1
[ 57.866025] sd 8:0:0:0: [sdi] Attached SCSI disk
[ 57.866160] scsi 9:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.866311] sd 9:0:0:0: [sdj] 293046768 512-byte hardware sectors (150040 MB)
[ 57.866365] sd 9:0:0:0: [sdj] Write Protect is off
[ 57.866412] sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 57.866422] sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.866533] sd 9:0:0:0: [sdj] 293046768 512-byte hardware sectors (150040 MB)
[ 57.866591] sd 9:0:0:0: [sdj] Write Protect is off
[ 57.866649] sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 57.866660] sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.866732] sdj: sdj1
[ 57.871781] sd 9:0:0:0: [sdj] Attached SCSI disk
[ 57.871887] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 57.872070] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 57.872120] scsi10 : sata_sil24
[ 57.872195] scsi11 : sata_sil24
[ 57.872265] ata11: SATA max UDMA/100 cmd 0xffffc20000070000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 57.872339] ata12: SATA max UDMA/100 cmd 0xffffc20000072000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
[ 58.276407] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 58.278892] ata11.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 58.278964] ata11.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 58.279019] ata11.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 58.282273] ata11.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 58.282345] ata11.00: configured for UDMA/100
[ 58.686525] ata12: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 58.689025] ata12.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 58.689096] ata12.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 58.689180] ata12.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 58.692407] ata12.00: ata_hpa_resize 1: sectors = 293046768, hpa_sectors = 293046768
[ 58.692481] ata12.00: configured for UDMA/100
[ 58.692587] scsi 10:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 58.692737] sd 10:0:0:0: [sdk] 293046768 512-byte hardware sectors (150040 MB)
[ 58.692819] sd 10:0:0:0: [sdk] Write Protect is off
[ 58.692866] sd 10:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 58.692876] sd 10:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.692988] sd 10:0:0:0: [sdk] 293046768 512-byte hardware sectors (150040 MB)
[ 58.693061] sd 10:0:0:0: [sdk] Write Protect is off
[ 58.693126] sd 10:0:0:0: [sdk] Mode Sense: 00 3a 00 00
[ 58.693136] sd 10:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.693207] sdk: sdk1
[ 58.702890] sd 10:0:0:0: [sdk] Attached SCSI disk
[ 58.703033] scsi 11:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 58.703169] sd 11:0:0:0: [sdl] 293046768 512-byte hardware sectors (150040 MB)
[ 58.703238] sd 11:0:0:0: [sdl] Write Protect is off
[ 58.703286] sd 11:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 58.703296] sd 11:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.703408] sd 11:0:0:0: [sdl] 293046768 512-byte hardware sectors (150040 MB)
[ 58.703482] sd 11:0:0:0: [sdl] Write Protect is off
[ 58.703529] sd 11:0:0:0: [sdl] Mode Sense: 00 3a 00 00
[ 58.703539] sd 11:0:0:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.703610] sdl: sdl1
[ 58.712922] sd 11:0:0:0: [sdl] Attached SCSI disk
[ 58.713060] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 58.713177] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 58.713217] scsi12 : pata_marvell
[ 58.713294] scsi13 : pata_marvell
[ 58.713386] ata13: PATA max UDMA/100 cmd 0x0000000000015018 ctl 0x0000000000015026 bmdma 0x0000000000015000 irq 0
[ 58.713458] ata14: DUMMY
[ 58.713527] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00
[ 59.019568] ata13.00: ATAPI, max UDMA/33
[ 59.178746] ata13.00: configured for UDMA/33
[ 59.179810] scsi 12:0:0:0: CD-ROM _NEC DVD_RW ND-3520A 1.04 PQ: 0 ANSI: 5
[ 59.184063] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 59.184112] Uniform CD-ROM driver Revision: 3.20
[ 59.184193] sr 12:0:0:0: Attached scsi CD-ROM sr0
[ 59.184253] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 59.184358] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 59.184361] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 59.184450] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 59.184541] ehci_hcd 0000:00:1a.7: debug port 1
[ 59.184588] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 59.184591] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0625c00
[ 59.188525] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 59.188683] usb usb1: configuration #1 chosen from 1 choice
[ 59.188755] hub 1-0:1.0: USB hub found
[ 59.188803] hub 1-0:1.0: 4 ports detected
[ 59.289605] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 59.289707] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 59.289711] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 59.289813] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 59.289900] ehci_hcd 0000:00:1d.7: debug port 1
[ 59.289970] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 59.289976] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0625800
[ 59.293909] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 59.294043] usb usb2: configuration #1 chosen from 1 choice
[ 59.294136] hub 2-0:1.0: USB hub found
[ 59.294180] hub 2-0:1.0: 6 ports detected
[ 59.395292] USB Universal Host Controller Interface driver v3.0
[ 59.395383] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 59.395508] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 59.395510] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 59.395578] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 59.395662] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000060c0
[ 59.395796] usb usb3: configuration #1 chosen from 1 choice
[ 59.395868] hub 3-0:1.0: USB hub found
[ 59.396512] hub 3-0:1.0: 2 ports detected
[ 59.498341] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 59.498438] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 59.498442] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 59.498542] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 59.498628] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000060a0
[ 59.498779] usb usb4: configuration #1 chosen from 1 choice
[ 59.498848] hub 4-0:1.0: USB hub found
[ 59.498896] hub 4-0:1.0: 2 ports detected
[ 59.599341] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 59.599439] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 59.599442] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 59.599547] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 59.599631] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00006080
[ 59.599783] usb usb5: configuration #1 chosen from 1 choice
[ 59.599855] hub 5-0:1.0: USB hub found
[ 59.599902] hub 5-0:1.0: 2 ports detected
[ 59.700337] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 59.700443] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 59.700446] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 59.700538] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 59.700619] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006060
[ 59.700772] usb usb6: configuration #1 chosen from 1 choice
[ 59.700842] hub 6-0:1.0: USB hub found
[ 59.700890] hub 6-0:1.0: 2 ports detected
[ 59.801355] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 59.801458] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 59.801461] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 59.801549] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 59.801631] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040
[ 59.801782] usb usb7: configuration #1 chosen from 1 choice
[ 59.801851] hub 7-0:1.0: USB hub found
[ 59.801898] hub 7-0:1.0: 2 ports detected
[ 59.902371] Initializing USB Mass Storage driver...
[ 59.906365] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 60.066711] usb 5-1: configuration #1 chosen from 1 choice
[ 60.069764] usbcore: registered new interface driver usb-storage
[ 60.069814] USB Mass Storage support registered.
[ 60.069933] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 60.072839] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 60.072886] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 60.072959] mice: PS/2 mouse device common for all mice
[ 60.073175] input: PC Speaker as /class/input/input0
[ 60.073224] i2c /dev entries driver
[ 60.073338] coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
[ 60.073453] coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
[ 60.073562] coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
[ 60.073675] coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
[ 60.073779] md: raid1 personality registered for level 1
[ 60.090134] raid6: int64x1 2023 MB/s
[ 60.107135] raid6: int64x2 2781 MB/s
[ 60.124120] raid6: int64x4 3109 MB/s
[ 60.141143] raid6: int64x8 1917 MB/s
[ 60.158123] raid6: sse2x1 3843 MB/s
[ 60.175118] raid6: sse2x2 4238 MB/s
[ 60.192112] raid6: sse2x4 6796 MB/s
[ 60.192154] raid6: using algorithm sse2x4 (6796 MB/s)
[ 60.192202] md: raid6 personality registered for level 6
[ 60.192247] md: raid5 personality registered for level 5
[ 60.192294] md: raid4 personality registered for level 4
[ 60.192340] raid5: automatically using best checksumming function: generic_sse
[ 60.197110] generic_sse: 8584.000 MB/sec
[ 60.197153] raid5: using function: generic_sse (8584.000 MB/sec)
[ 60.197228] usbcore: registered new interface driver hiddev
[ 60.643555] hiddev96: USB HID v1.00 Device [ UPS] on usb-0000:00:1d.0-1
[ 60.643672] usbcore: registered new interface driver usbhid
[ 60.643721] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 60.643781] Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
[ 60.643996] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 60.644106] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 60.711615] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 60.735452] input: AT Translated Set 2 keyboard as /class/input/input2
[ 60.779950] ALSA device list:
[ 60.779996] #0: HDA Intel at 0xe0620000 irq 22
[ 60.780049] u32 classifier
[ 60.780102] Actions configured
[ 60.780167] nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
[ 60.780378] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 60.780475] TCP cubic registered
[ 60.780533] NET: Registered protocol family 1
[ 60.780590] NET: Registered protocol family 17
[ 60.780895] md: Autodetecting RAID arrays.
[ 60.926037] md: autorun ...
[ 60.926077] md: considering sdl1 ...
[ 60.926145] md: adding sdl1 ...
[ 60.926190] md: adding sdk1 ...
[ 60.926235] md: adding sdj1 ...
[ 60.926290] md: adding sdi1 ...
[ 60.926345] md: adding sdh1 ...
[ 60.926389] md: adding sdg1 ...
[ 60.926434] md: adding sdf1 ...
[ 60.926479] md: adding sde1 ...
[ 60.926524] md: adding sdd1 ...
[ 60.926566] md: adding sdc1 ...
[ 60.926610] md: sdb3 has different UUID to sdl1
[ 60.926658] md: sdb2 has different UUID to sdl1
[ 60.926705] md: sdb1 has different UUID to sdl1
[ 60.926751] md: sda3 has different UUID to sdl1
[ 60.926798] md: sda2 has different UUID to sdl1
[ 60.926846] md: sda1 has different UUID to sdl1
[ 60.926926] md: created md3
[ 60.926967] md: bind<sdc1>
[ 60.927013] md: bind<sdd1>
[ 60.927058] md: bind<sde1>
[ 60.927104] md: bind<sdf1>
[ 60.927160] md: bind<sdg1>
[ 60.927216] md: bind<sdh1>
[ 60.927262] md: bind<sdi1>
[ 60.927308] md: bind<sdj1>
[ 60.927374] md: bind<sdk1>
[ 60.927420] md: bind<sdl1>
[ 60.927467] md: running: <sdl1><sdk1><sdj1><sdi1><sdh1><sdg1><sdf1><sde1><sdd1><sdc1>
[ 60.927774] raid5: device sdl1 operational as raid disk 2
[ 60.927824] raid5: device sdk1 operational as raid disk 3
[ 60.927872] raid5: device sdj1 operational as raid disk 0
[ 60.927919] raid5: device sdi1 operational as raid disk 1
[ 60.927968] raid5: device sdh1 operational as raid disk 6
[ 60.928016] raid5: device sdg1 operational as raid disk 5
[ 60.928063] raid5: device sdf1 operational as raid disk 4
[ 60.928111] raid5: device sde1 operational as raid disk 7
[ 60.928159] raid5: device sdd1 operational as raid disk 8
[ 60.928227] raid5: device sdc1 operational as raid disk 9
[ 60.928780] raid5: allocated 10562kB for md3
[ 60.928825] raid5: raid level 5 set md3 active with 10 out of 10 devices, algorithm 2
[ 60.928893] RAID5 conf printout:
[ 60.928937] --- rd:10 wd:10
[ 60.928979] disk 0, o:1, dev:sdj1
[ 60.929022] disk 1, o:1, dev:sdi1
[ 60.929065] disk 2, o:1, dev:sdl1
[ 60.929106] disk 3, o:1, dev:sdk1
[ 60.929150] disk 4, o:1, dev:sdf1
[ 60.929193] disk 5, o:1, dev:sdg1
[ 60.929236] disk 6, o:1, dev:sdh1
[ 60.929300] disk 7, o:1, dev:sde1
[ 60.929343] disk 8, o:1, dev:sdd1
[ 60.929386] disk 9, o:1, dev:sdc1
[ 60.929487] md: considering sdb3 ...
[ 60.929531] md: adding sdb3 ...
[ 60.929576] md: sdb2 has different UUID to sdb3
[ 60.929620] md: sdb1 has different UUID to sdb3
[ 60.929668] md: adding sda3 ...
[ 60.929709] md: sda2 has different UUID to sdb3
[ 60.929756] md: sda1 has different UUID to sdb3
[ 60.929832] md: created md2
[ 60.929872] md: bind<sda3>
[ 60.929918] md: bind<sdb3>
[ 60.929964] md: running: <sdb3><sda3>
[ 60.930104] raid1: raid set md2 active with 2 out of 2 mirrors
[ 60.930172] md: considering sdb2 ...
[ 60.930218] md: adding sdb2 ...
[ 60.930262] md: sdb1 has different UUID to sdb2
[ 60.930331] md: adding sda2 ...
[ 60.930375] md: sda1 has different UUID to sdb2
[ 60.930451] md: created md1
[ 60.930515] md: bind<sda2>
[ 60.930557] md: bind<sdb2>
[ 60.930604] md: running: <sdb2><sda2>
[ 60.930742] raid1: raid set md1 active with 2 out of 2 mirrors
[ 60.930813] md: considering sdb1 ...
[ 60.930860] md: adding sdb1 ...
[ 60.930904] md: adding sda1 ...
[ 60.930949] md: created md0
[ 60.930991] md: bind<sda1>
[ 60.931038] md: bind<sdb1>
[ 60.931085] md: running: <sdb1><sda1>
[ 60.931223] raid1: raid set md0 active with 2 out of 2 mirrors
[ 60.931889] md: ... autorun DONE.
[ 60.956814] UDF-fs: No VRS found
[ 60.957045] Filesystem "md2": Disabling barriers, not supported by the underlying device
[ 60.969374] XFS mounting filesystem md2
[ 61.038746] Ending clean XFS mount for filesystem: md2
[ 61.038765] VFS: Mounted root (xfs filesystem) readonly.
[ 61.038867] Freeing unused kernel memory: 216k freed
[ 63.031810] Adding 16787768k swap on /dev/md0. Priority:-1 extents:1 across:16787768k
[ 63.085652] Filesystem "md2": Disabling barriers, not supported by the underlying device
[ 63.876749] kjournald starting. Commit interval 5 seconds
[ 63.883153] EXT3 FS on md1, internal journal
[ 63.883225] EXT3-fs: mounted filesystem with ordered data mode.
[ 63.883591] Filesystem "md3": Disabling barriers, not supported by the underlying device
[ 63.883845] XFS mounting filesystem md3
[ 64.258308] Ending clean XFS mount for filesystem: md3
[ 82.579367] e1000: eth1: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 84.433542] process `syslogd' is using obsolete setsockopt SO_BSDCOMPAT
[ 105.528789] mtrr: no more MTRRs available
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
