On Tue, 29 May 2007, Robert Hancock wrote:
Justin Piszcz wrote:
Short Description of Problem:
Linux 2.6.21.3 does not run properly with 8GB of ram on the Intel 965WH
motherboard.
Long Description of Problem:
When I use 8GB of memory on my x86_64 system, CPU-bound processes are VERY
slow, up to 36x slower than usual. My temporary fix is force Linux to only
use 4GB of memory, I am currently using mem=4096M. I ran memtest86 and the
memory is fine, not a single error. I tried the following to mem= 1024,
2048
4096 and blank "" to let the kernel use all 8GB of memory. What is wrong
with the kernel and how come it cannot use 8GB of memory without slowing
down
all CPU-related processes to a snail-like pace? There is something
horribly
wrong here.
Conclusion: For now, I will be using mem=4096M until someone can help me
understand what is happening here. Can anyone offer any insight?
I found it interesting in make menuconfig on x86_64 there is no 4GB/64GB
options in the kernel that I remember seeing in 32bit.
That's because that option is not applicable in 64-bit mode.
Can you send your full dmesg output from the 8GB bootup?
--
Robert Hancock Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/
Kernel dmesg attached from 8GB bootup.
Robert, how come the option is not applicable in 64-bit mode? If I want to
use all 8GB of memory I need to run a 32-bit kernel?
Justin.
000-e0bfffff
[ 49.640593] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 49.640760] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 49.640884] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 49.641100] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 49.641236] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 49.641399] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 49.641510] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 49.641674] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 49.641787] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
[ 49.641953] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 49.642061] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 49.642960] NET: Registered protocol family 2
[ 49.652907] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 49.661992] TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
[ 49.674484] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 49.678704] TCP: Hash tables configured (established 131072 bind 65536)
[ 49.678792] TCP reno registered
[ 49.734605] Installing knfsd (copyright (C) 1996 [email protected]).
[ 49.738786] SGI XFS with large block/inode numbers, no debug enabled
[ 49.751315] io scheduler noop registered
[ 49.751397] io scheduler anticipatory registered (default)
[ 49.758137] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 49.758350] assign_interrupt_mode Found MSI capability
[ 49.758914] Allocate Port Service[0000:00:1c.0:pcie00]
[ 49.761087] Allocate Port Service[0000:00:1c.0:pcie02]
[ 49.763372] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 49.763567] assign_interrupt_mode Found MSI capability
[ 49.763851] Allocate Port Service[0000:00:1c.1:pcie00]
[ 49.766170] Allocate Port Service[0000:00:1c.1:pcie02]
[ 49.768444] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 49.768636] assign_interrupt_mode Found MSI capability
[ 49.768903] Allocate Port Service[0000:00:1c.2:pcie00]
[ 49.771250] Allocate Port Service[0000:00:1c.2:pcie02]
[ 49.773535] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 49.773745] assign_interrupt_mode Found MSI capability
[ 49.774010] Allocate Port Service[0000:00:1c.3:pcie00]
[ 49.776336] Allocate Port Service[0000:00:1c.3:pcie02]
[ 49.778728] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 49.778922] assign_interrupt_mode Found MSI capability
[ 49.779166] Allocate Port Service[0000:00:1c.4:pcie00]
[ 49.781407] Allocate Port Service[0000:00:1c.4:pcie02]
[ 49.928519] lp: driver loaded but no devices found
[ 49.930317] Real Time Clock Driver v1.12ac
[ 49.932862] hpet_resources: 0xfed00000 is busy
[ 49.932999] Linux agpgart interface v0.102 (c) Dave Jones
[ 49.934495] agpgart: Detected an Intel 965G Chipset.
[ 49.935555] agpgart: Detected 7676K stolen memory.
[ 49.955435] agpgart: AGP aperture is 256M @ 0xd0000000
[ 49.955998] [drm] Initialized drm 1.1.0 20060810
[ 49.956245] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 49.959487] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 49.961590] parport: PnPBIOS parport detected.
[ 49.961837] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 50.047129] lp0: using parport0 (interrupt-driven).
[ 50.059429] loop: loaded (max 8 devices)
[ 50.059512] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 50.059601] Copyright (c) 1999-2006 Intel Corporation.
[ 50.060611] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 50.060818] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 50.078969] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:6e:9d:43
[ 50.156941] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 50.157413] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 50.423850] e1000: 0000:06:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:00:cd:b1
[ 50.574287] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 50.574507] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 50.825325] e1000: 0000:06:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:29:37:db
[ 50.854886] e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 50.857929] netconsole: device eth0 not up yet, forcing it
[ 50.900485] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090270001c5be9f]
[ 53.023002] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 53.519027] netconsole: network logging started
[ 53.525561] ahci 0000:00:1f.2: version 2.1
[ 53.525660] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 54.527020] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 54.527094] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 54.527265] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 54.529799] ata1: SATA max UDMA/133 cmd 0xffffc20000078100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 377
[ 54.532861] ata2: SATA max UDMA/133 cmd 0xffffc20000078180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 377
[ 54.535954] ata3: SATA max UDMA/133 cmd 0xffffc20000078200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 377
[ 54.538921] ata4: SATA max UDMA/133 cmd 0xffffc20000078280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 377
[ 54.540937] ata5: SATA max UDMA/133 cmd 0xffffc20000078300 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 377
[ 54.542961] ata6: SATA max UDMA/133 cmd 0xffffc20000078380 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 377
[ 54.543238] scsi0 : ahci
[ 55.005900] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 55.008490] ata1.00: ATA-6: WDC WD740GD-00FLC0, 33.08F33, max UDMA/133
[ 55.008659] ata1.00: 145226112 sectors, multi 0: LBA48
[ 55.012548] ata1.00: configured for UDMA/133
[ 55.012871] scsi1 : ahci
[ 55.473558] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 55.476111] ata2.00: ATA-6: WDC WD740GD-00FLC0, 33.08F33, max UDMA/133
[ 55.476256] ata2.00: 145226112 sectors, multi 0: LBA48
[ 55.480168] ata2.00: configured for UDMA/133
[ 55.480519] scsi2 : ahci
[ 55.941187] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 55.942994] ata3.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 55.943170] ata3.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 55.945896] ata3.00: configured for UDMA/133
[ 55.946135] scsi3 : ahci
[ 56.407830] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 56.409600] ata4.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 56.409743] ata4.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 56.412464] ata4.00: configured for UDMA/133
[ 56.412763] scsi4 : ahci
[ 56.873467] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 56.875195] ata5.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 56.875362] ata5.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 56.877986] ata5.00: configured for UDMA/133
[ 56.878375] scsi5 : ahci
[ 57.337984] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 57.339683] ata6.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 57.339878] ata6.00: 293046768 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 57.342457] ata6.00: configured for UDMA/133
[ 57.344076] scsi 0:0:0:0: Direct-Access ATA WDC WD740GD-00FL 33.0 PQ: 0 ANSI: 5
[ 57.348418] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 57.348753] sda: Write Protect is off
[ 57.348867] sda: Mode Sense: 00 3a 00 00
[ 57.349355] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.350304] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 57.350641] sda: Write Protect is off
[ 57.350751] sda: Mode Sense: 00 3a 00 00
[ 57.351205] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.351384] sda: sda1 sda2 sda3
[ 57.364283] sd 0:0:0:0: Attached scsi disk sda
[ 57.366414] scsi 1:0:0:0: Direct-Access ATA WDC WD740GD-00FL 33.0 PQ: 0 ANSI: 5
[ 57.369407] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
[ 57.369729] sdb: Write Protect is off
[ 57.369842] sdb: Mode Sense: 00 3a 00 00
[ 57.370199] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.371070] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
[ 57.371368] sdb: Write Protect is off
[ 57.371494] sdb: Mode Sense: 00 3a 00 00
[ 57.371868] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.372018] sdb: sdb1 sdb2 sdb3
[ 57.388421] sd 1:0:0:0: Attached scsi disk sdb
[ 57.390640] scsi 2:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.393573] SCSI device sdc: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.393863] sdc: Write Protect is off
[ 57.393981] sdc: Mode Sense: 00 3a 00 00
[ 57.394388] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.395180] SCSI device sdc: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.395504] sdc: Write Protect is off
[ 57.395617] sdc: Mode Sense: 00 3a 00 00
[ 57.395987] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.396145] sdc: sdc1
[ 57.404704] sd 2:0:0:0: Attached scsi disk sdc
[ 57.407759] scsi 3:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.410796] SCSI device sdd: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.411106] sdd: Write Protect is off
[ 57.411218] sdd: Mode Sense: 00 3a 00 00
[ 57.411577] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.412452] SCSI device sdd: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.412804] sdd: Write Protect is off
[ 57.412921] sdd: Mode Sense: 00 3a 00 00
[ 57.413290] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.413436] sdd: sdd1
[ 57.421753] sd 3:0:0:0: Attached scsi disk sdd
[ 57.423890] scsi 4:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.426871] SCSI device sde: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.427230] sde: Write Protect is off
[ 57.427345] sde: Mode Sense: 00 3a 00 00
[ 57.427701] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.428551] SCSI device sde: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.428844] sde: Write Protect is off
[ 57.428961] sde: Mode Sense: 00 3a 00 00
[ 57.429379] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.429525] sde: sde1
[ 57.436029] sd 4:0:0:0: Attached scsi disk sde
[ 57.438009] scsi 5:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 57.441059] SCSI device sdf: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.441354] sdf: Write Protect is off
[ 57.441493] sdf: Mode Sense: 00 3a 00 00
[ 57.441895] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.442827] SCSI device sdf: 293046768 512-byte hdwr sectors (150040 MB)
[ 57.443125] sdf: Write Protect is off
[ 57.443238] sdf: Mode Sense: 00 3a 00 00
[ 57.443585] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 57.443772] sdf: sdf1
[ 57.454230] sd 5:0:0:0: Attached scsi disk sdf
[ 57.458231] sata_sil24 0000:03:00.0: version 0.8
[ 57.458330] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 57.458846] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 57.460520] ata7: SATA max UDMA/100 cmd 0xffffc20000108000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 18
[ 57.462550] ata8: SATA max UDMA/100 cmd 0xffffc2000010a000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 18
[ 57.462791] scsi6 : sata_sil24
[ 57.868886] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 57.870905] ata7.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 57.871050] ata7.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 57.874086] ata7.00: configured for UDMA/100
[ 57.874254] scsi7 : sata_sil24
[ 58.282187] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 58.284214] ata8.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 58.284358] ata8.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 58.287439] ata8.00: configured for UDMA/100
[ 58.288621] scsi 6:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 58.291911] SCSI device sdg: 293046768 512-byte hdwr sectors (150040 MB)
[ 58.292200] sdg: Write Protect is off
[ 58.292324] sdg: Mode Sense: 00 3a 00 00
[ 58.292667] SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.293503] SCSI device sdg: 293046768 512-byte hdwr sectors (150040 MB)
[ 58.293832] sdg: Write Protect is off
[ 58.293976] sdg: Mode Sense: 00 3a 00 00
[ 58.294337] SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.295071] sdg: sdg1
[ 58.302951] sd 6:0:0:0: Attached scsi disk sdg
[ 58.306104] scsi 7:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 58.309130] SCSI device sdh: 293046768 512-byte hdwr sectors (150040 MB)
[ 58.309486] sdh: Write Protect is off
[ 58.309600] sdh: Mode Sense: 00 3a 00 00
[ 58.309956] SCSI device sdh: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.310823] SCSI device sdh: 293046768 512-byte hdwr sectors (150040 MB)
[ 58.311115] sdh: Write Protect is off
[ 58.311229] sdh: Mode Sense: 00 3a 00 00
[ 58.311640] SCSI device sdh: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 58.311790] sdh: sdh1
[ 58.320078] sd 7:0:0:0: Attached scsi disk sdh
[ 58.321348] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 58.321800] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 58.323417] ata9: SATA max UDMA/100 cmd 0xffffc20000110000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
[ 58.325432] ata10: SATA max UDMA/100 cmd 0xffffc20000112000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 19
[ 58.325647] scsi8 : sata_sil24
[ 58.733657] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 58.735434] ata9.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 58.735563] ata9.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 58.738156] ata9.00: configured for UDMA/100
[ 58.738362] scsi9 : sata_sil24
[ 59.144898] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 59.146631] ata10.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 59.146779] ata10.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 59.149416] ata10.00: configured for UDMA/100
[ 59.150639] scsi 8:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 59.153672] SCSI device sdi: 293046768 512-byte hdwr sectors (150040 MB)
[ 59.153966] sdi: Write Protect is off
[ 59.154090] sdi: Mode Sense: 00 3a 00 00
[ 59.154501] SCSI device sdi: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 59.155336] SCSI device sdi: 293046768 512-byte hdwr sectors (150040 MB)
[ 59.155686] sdi: Write Protect is off
[ 59.155798] sdi: Mode Sense: 00 3a 00 00
[ 59.156159] SCSI device sdi: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 59.156306] sdi: sdi1
[ 59.166753] sd 8:0:0:0: Attached scsi disk sdi
[ 59.169023] scsi 9:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 59.171901] SCSI device sdj: 293046768 512-byte hdwr sectors (150040 MB)
[ 59.172223] sdj: Write Protect is off
[ 59.172347] sdj: Mode Sense: 00 3a 00 00
[ 59.172667] SCSI device sdj: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 59.173502] SCSI device sdj: 293046768 512-byte hdwr sectors (150040 MB)
[ 59.173797] sdj: Write Protect is off
[ 59.173908] sdj: Mode Sense: 00 3a 00 00
[ 59.174294] SCSI device sdj: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 59.174526] sdj: sdj1
[ 59.185042] sd 9:0:0:0: Attached scsi disk sdj
[ 59.186240] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 59.186777] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 59.188276] ata11: SATA max UDMA/100 cmd 0xffffc20000118000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
[ 59.190299] ata12: SATA max UDMA/100 cmd 0xffffc2000011a000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
[ 59.190596] scsi10 : sata_sil24
[ 59.596870] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 59.598911] ata11.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 59.599074] ata11.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 59.602172] ata11.00: configured for UDMA/100
[ 59.602343] scsi11 : sata_sil24
[ 60.008363] ata12: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 60.010395] ata12.00: ATA-7: WDC WD1500ADFD-00NLR1, 20.07P20, max UDMA/133
[ 60.010565] ata12.00: 293046768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 60.013634] ata12.00: configured for UDMA/100
[ 60.014772] scsi 10:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 60.017135] SCSI device sdk: 293046768 512-byte hdwr sectors (150040 MB)
[ 60.017428] sdk: Write Protect is off
[ 60.017578] sdk: Mode Sense: 00 3a 00 00
[ 60.017958] SCSI device sdk: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 60.018811] SCSI device sdk: 293046768 512-byte hdwr sectors (150040 MB)
[ 60.019098] sdk: Write Protect is off
[ 60.019208] sdk: Mode Sense: 00 3a 00 00
[ 60.019574] SCSI device sdk: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 60.019766] sdk: sdk1
[ 60.027242] sd 10:0:0:0: Attached scsi disk sdk
[ 60.029522] scsi 11:0:0:0: Direct-Access ATA WDC WD1500ADFD-0 20.0 PQ: 0 ANSI: 5
[ 60.032343] SCSI device sdl: 293046768 512-byte hdwr sectors (150040 MB)
[ 60.032627] sdl: Write Protect is off
[ 60.032746] sdl: Mode Sense: 00 3a 00 00
[ 60.033132] SCSI device sdl: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 60.033951] SCSI device sdl: 293046768 512-byte hdwr sectors (150040 MB)
[ 60.034305] sdl: Write Protect is off
[ 60.034417] sdl: Mode Sense: 00 3a 00 00
[ 60.034782] SCSI device sdl: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 60.034928] sdl: sdl1
[ 60.042358] sd 11:0:0:0: Attached scsi disk sdl
[ 60.044446] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 60.044876] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 60.046191] ata13: PATA max UDMA/100 cmd 0x0000000000015018 ctl 0x0000000000015026 bmdma 0x0000000000015000 irq 17
[ 60.046482] scsi12 : pata_marvell
[ 60.049123] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00
[ 60.357681] ata13.00: ATAPI, max UDMA/33
[ 60.511908] ata13.00: configured for UDMA/33
[ 60.514242] scsi 12:0:0:0: CD-ROM _NEC DVD_RW ND-3520A 1.04 PQ: 0 ANSI: 5
[ 60.522460] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 60.522608] Uniform CD-ROM driver Revision: 3.20
[ 60.524264] sr 12:0:0:0: Attached scsi CD-ROM sr0
[ 60.526162] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 60.526488] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 60.526528] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 60.528219] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 60.528706] ehci_hcd 0000:00:1a.7: debug port 1
[ 60.528858] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 60.528953] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0625c00
[ 60.532957] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 60.537324] usb usb1: configuration #1 chosen from 1 choice
[ 60.539211] hub 1-0:1.0: USB hub found
[ 60.539382] hub 1-0:1.0: 4 ports detected
[ 60.643405] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 60.643725] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 60.643767] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 60.645247] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 60.645754] ehci_hcd 0000:00:1d.7: debug port 1
[ 60.645895] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 60.646009] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0625800
[ 60.650021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 60.654403] usb usb2: configuration #1 chosen from 1 choice
[ 60.656306] hub 2-0:1.0: USB hub found
[ 60.656477] hub 2-0:1.0: 6 ports detected
[ 60.761478] USB Universal Host Controller Interface driver v3.0
[ 60.762558] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 60.762838] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 60.762888] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 60.764431] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 60.764660] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000060c0
[ 60.768583] usb usb3: configuration #1 chosen from 1 choice
[ 60.770496] hub 3-0:1.0: USB hub found
[ 60.770667] hub 3-0:1.0: 2 ports detected
[ 60.875709] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 60.875977] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 60.876018] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 60.877630] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 60.877881] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000060a0
[ 60.881780] usb usb4: configuration #1 chosen from 1 choice
[ 60.883704] hub 4-0:1.0: USB hub found
[ 60.883873] hub 4-0:1.0: 2 ports detected
[ 60.987952] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 60.988221] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 60.988261] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 60.989797] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 60.990028] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00006080
[ 60.993964] usb usb5: configuration #1 chosen from 1 choice
[ 60.995826] hub 5-0:1.0: USB hub found
[ 60.996041] hub 5-0:1.0: 2 ports detected
[ 61.100070] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 61.100346] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 61.100388] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 61.101896] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 61.102183] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006060
[ 61.106057] usb usb6: configuration #1 chosen from 1 choice
[ 61.107967] hub 6-0:1.0: USB hub found
[ 61.108142] hub 6-0:1.0: 2 ports detected
[ 61.212093] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 61.212358] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 61.212412] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 61.214107] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 61.214339] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040
[ 61.218173] usb usb7: configuration #1 chosen from 1 choice
[ 61.220096] hub 7-0:1.0: USB hub found
[ 61.220270] hub 7-0:1.0: 2 ports detected
[ 61.306473] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 61.325345] Initializing USB Mass Storage driver...
[ 61.473424] usb 5-1: configuration #1 chosen from 1 choice
[ 61.480883] usbcore: registered new interface driver usb-storage
[ 61.481015] USB Mass Storage support registered.
[ 61.482491] usbcore: registered new interface driver hiddev
[ 61.978902] hiddev96: USB HID v1.00 Device [ UPS] on usb-0000:00:1d.0-1
[ 61.979246] usbcore: registered new interface driver usbhid
[ 61.979406] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 61.982163] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 61.986899] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 61.987036] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 61.988264] mice: PS/2 mouse device common for all mice
[ 61.993425] input: PC Speaker as /class/input/input0
[ 61.993643] i2c /dev entries driver
[ 61.995182] md: raid1 personality registered for level 1
[ 62.012377] raid6: int64x1 66 MB/s
[ 62.029504] raid6: int64x2 97 MB/s
[ 62.047329] raid6: int64x4 35 MB/s
[ 62.068731] raid6: int64x8 15 MB/s
[ 62.085968] raid6: sse2x1 152 MB/s
[ 62.102982] raid6: sse2x2 285 MB/s
[ 62.119904] raid6: sse2x4 484 MB/s
[ 62.120036] raid6: using algorithm sse2x4 (484 MB/s)
[ 62.120177] md: raid6 personality registered for level 6
[ 62.120321] md: raid5 personality registered for level 5
[ 62.120435] md: raid4 personality registered for level 4
[ 62.120579] raid5: automatically using best checksumming function: generic_sse
[ 62.124860] generic_sse: 56.000 MB/sec
[ 62.124973] raid5: using function: generic_sse (56.000 MB/sec)
[ 62.125489] Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC).
[ 62.131442] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 62.131831] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 62.281613] ALSA device list:
[ 62.281730] #0: HDA Intel at 0xe0620000 irq 22
[ 62.281912] u32 classifier
[ 62.282010] Actions configured
[ 62.282147] nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
[ 62.284736] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 62.285856] TCP cubic registered
[ 62.286229] NET: Registered protocol family 1
[ 62.286374] NET: Registered protocol family 17
[ 62.654025] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 62.681530] input: AT Translated Set 2 keyboard as /class/input/input2
[ 62.695712] md: Autodetecting RAID arrays.
[ 62.864377] md: autorun ...
[ 62.864501] md: considering sdl1 ...
[ 62.864888] md: adding sdl1 ...
[ 62.865262] md: adding sdk1 ...
[ 62.865596] md: adding sdj1 ...
[ 62.865951] md: adding sdi1 ...
[ 62.866304] md: adding sdh1 ...
[ 62.866641] md: adding sdg1 ...
[ 62.866992] md: adding sdf1 ...
[ 62.867346] md: adding sde1 ...
[ 62.867688] md: adding sdd1 ...
[ 62.868041] md: adding sdc1 ...
[ 62.868250] md: sdb3 has different UUID to sdl1
[ 62.868441] md: sdb2 has different UUID to sdl1
[ 62.868628] md: sdb1 has different UUID to sdl1
[ 62.868818] md: sda3 has different UUID to sdl1
[ 62.869005] md: sda2 has different UUID to sdl1
[ 62.869255] md: sda1 has different UUID to sdl1
[ 62.871018] md: created md3
[ 62.871156] md: bind<sdc1>
[ 62.871472] md: bind<sdd1>
[ 62.871744] md: bind<sde1>
[ 62.872062] md: bind<sdf1>
[ 62.872524] md: bind<sdg1>
[ 62.872869] md: bind<sdh1>
[ 62.873158] md: bind<sdi1>
[ 62.873521] md: bind<sdj1>
[ 62.873823] md: bind<sdk1>
[ 62.874123] md: bind<sdl1>
[ 62.874573] md: running: <sdl1><sdk1><sdj1><sdi1><sdh1><sdg1><sdf1><sde1><sdd1><sdc1>
[ 62.877780] raid5: device sdl1 operational as raid disk 2
[ 62.877903] raid5: device sdk1 operational as raid disk 3
[ 62.878059] raid5: device sdj1 operational as raid disk 0
[ 62.878183] raid5: device sdi1 operational as raid disk 1
[ 62.878341] raid5: device sdh1 operational as raid disk 6
[ 62.878512] raid5: device sdg1 operational as raid disk 5
[ 62.878668] raid5: device sdf1 operational as raid disk 4
[ 62.878812] raid5: device sde1 operational as raid disk 7
[ 62.878966] raid5: device sdd1 operational as raid disk 8
[ 62.879088] raid5: device sdc1 operational as raid disk 9
[ 62.899044] raid5: allocated 10562kB for md3
[ 62.899164] raid5: raid level 5 set md3 active with 10 out of 10 devices, algorithm 2
[ 62.899371] RAID5 conf printout:
[ 62.899497] --- rd:10 wd:10
[ 62.899630] disk 0, o:1, dev:sdj1
[ 62.899762] disk 1, o:1, dev:sdi1
[ 62.899895] disk 2, o:1, dev:sdl1
[ 62.900025] disk 3, o:1, dev:sdk1
[ 62.900154] disk 4, o:1, dev:sdf1
[ 62.900316] disk 5, o:1, dev:sdg1
[ 62.900460] disk 6, o:1, dev:sdh1
[ 62.900606] disk 7, o:1, dev:sde1
[ 62.900720] disk 8, o:1, dev:sdd1
[ 62.900864] disk 9, o:1, dev:sdc1
[ 62.902910] md: considering sdb3 ...
[ 62.903255] md: adding sdb3 ...
[ 62.903492] md: sdb2 has different UUID to sdb3
[ 62.903696] md: sdb1 has different UUID to sdb3
[ 62.904029] md: adding sda3 ...
[ 62.904213] md: sda2 has different UUID to sdb3
[ 62.904428] md: sda1 has different UUID to sdb3
[ 62.906017] md: created md2
[ 62.906131] md: bind<sda3>
[ 62.906521] md: bind<sdb3>
[ 62.906856] md: running: <sdb3><sda3>
[ 62.909833] raid1: raid set md2 active with 2 out of 2 mirrors
[ 62.911031] md: considering sdb2 ...
[ 62.911359] md: adding sdb2 ...
[ 62.911550] md: sdb1 has different UUID to sdb2
[ 62.911945] md: adding sda2 ...
[ 62.912126] md: sda1 has different UUID to sdb2
[ 62.914168] md: created md1
[ 62.914280] md: bind<sda2>
[ 62.914600] md: bind<sdb2>
[ 62.914949] md: running: <sdb2><sda2>
[ 62.917888] raid1: raid set md1 active with 2 out of 2 mirrors
[ 62.919053] md: considering sdb1 ...
[ 62.919382] md: adding sdb1 ...
[ 62.919735] md: adding sda1 ...
[ 62.919843] md: created md0
[ 62.920029] md: bind<sda1>
[ 62.920313] md: bind<sdb1>
[ 62.920759] md: running: <sdb1><sda1>
[ 62.923893] raid1: raid set md0 active with 2 out of 2 mirrors
[ 62.925114] md: ... autorun DONE.
[ 62.986800] UDF-fs: No VRS found
[ 62.989910] Filesystem "md2": Disabling barriers, not supported by the underlying device
[ 63.003218] XFS mounting filesystem md2
[ 63.086036] Ending clean XFS mount for filesystem: md2
[ 63.088268] VFS: Mounted root (xfs filesystem) readonly.
[ 63.088664] Freeing unused kernel memory: 220k freed
[ 140.336426] Adding 16787768k swap on /dev/md0. Priority:-1 extents:1 across:16787768k
[ 141.392860] Filesystem "md2": Disabling barriers, not supported by the underlying device
[ 164.783967] kjournald starting. Commit interval 5 seconds
[ 164.798654] EXT3 FS on md1, internal journal
[ 164.798884] EXT3-fs: mounted filesystem with ordered data mode.
[ 164.813348] Filesystem "md3": Disabling barriers, not supported by the underlying device
[ 164.820025] XFS mounting filesystem md3
[ 165.142472] Ending clean XFS mount for filesystem: md3
[ 214.133325] e1000: eth1: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 246.230184] process `syslogd' is using obsolete setsockopt SO_BSDCOMPAT
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
