This issue appears to be identical to the one reported here:
http://lists.opensuse.org/opensuse-amd64/2007-04/msg00001.html
By manually adding mem=4096M to my boot line, the system is able to
come up fine. Otherwise, it will randomly hang during boot after the
line:
agpgart: detected an Intel 965G chipset.
This is a Gigabyte GA-965P-DQ6 motherboard at the latest F10 BIOS
level. The full dmesg output from a working boot with mem=4096M is
attached.
Thanks -Andrew
Linux version 2.6.22-rc2-plateado (root@plateado) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #3 SMP Mon May 21 19:38:38 EDT 2007
Command line: root=/dev/sdg3 ro mem=4096M
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000097c00 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable)
BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS)
BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data)
BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Entering add_active_range(0, 0, 151) 0 entries of 256 used
Entering add_active_range(0, 256, 917216) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F6E70, 0014 (r0 GBT )
ACPI: RSDT DFEE3040, 0034 (r1 GBT GBTUACPI 42302E31 GBTU 1010101)
ACPI: FACP DFEE30C0, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101)
ACPI: DSDT DFEE3180, 49F4 (r1 GBT GBTUACPI 1000 MSFT 100000C)
ACPI: FACS DFEE0000, 0040
ACPI: HPET DFEE7CC0, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98)
ACPI: MCFG DFEE7D40, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101)
ACPI: APIC DFEE7BC0, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101)
Entering add_active_range(0, 0, 151) 0 entries of 256 used
Entering add_active_range(0, 256, 917216) 1 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 151
0: 256 -> 917216
On node 0 totalpages: 917111
DMA zone: 56 pages used for memmap
DMA zone: 960 pages reserved
DMA zone: 2975 pages, LIFO batch:0
DMA32 zone: 12484 pages used for memmap
DMA32 zone: 900636 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 0000000000097000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at e0000000 (gap: dff00000:10100000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 37128 bytes of per cpu data
Built 1 zonelists. Total pages: 903611
Kernel command line: root=/dev/sdg3 ro mem=4096M
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 2400.000 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
Memory: 3604856k/3668864k available (1953k kernel code, 63184k reserved, 974k data, 204k init)
Calibrating delay using timer specific routine.. 4803.25 BogoMIPS (lpj=9606519)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 16666647
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.02 BogoMIPS (lpj=9600045)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=19
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at f0000000 - f3ffffff
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0400
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid INT0800
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.20 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
BUG: at /usr/src/linux-2.6.22-rc2/mm/slab.c:777 __find_general_cachep()
Call Trace:
[<ffffffff802743dc>] __kmalloc+0x3e/0xbe
[<ffffffff8021d65f>] cache_k8_northbridges+0x7f/0xf0
[<ffffffff8052bb53>] gart_iommu_init+0x13/0x4f8
[<ffffffff802d15e1>] kobject_shadow_add+0xef/0x1a2
[<ffffffff802d13fb>] kobject_get+0x12/0x17
[<ffffffff8033b2a4>] class_register+0x10a/0x13d
[<ffffffff80527964>] pci_iommu_init+0x9/0x12
[<ffffffff8052060e>] kernel_init+0x167/0x2d7
[<ffffffff8020aba8>] child_rip+0xa/0x12
[<ffffffff802fb7e4>] acpi_ds_init_one_object+0x0/0x7c
[<ffffffff805204a7>] kernel_init+0x0/0x2d7
[<ffffffff8020ab9e>] child_rip+0x0/0x12
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: 00:09: ioport range 0x400-0x4bf could not be reserved
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: 00:0a: iomem range 0xf0000000-0xf3ffffff could not be reserved
pnp: match found with the PnP device '00:0b' and the driver 'system'
pnp: 00:0b: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:0b: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:0b: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0b: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: 7000-7fff
MEM window: f4000000-f6ffffff
PREFETCH window: e0000000-efffffff
PCI: Bridge: 0000:00:1c.0
IO window: 6000-6fff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: 8000-8fff
MEM window: f7000000-f8ffffff
PREFETCH window: f9300000-f93fffff
PCI: Bridge: 0000:00:1c.5
IO window: 9000-afff
MEM window: f9000000-f90fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: b000-bfff
MEM window: f9100000-f91fffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
Time: tsc clocksource has been installed.
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2610k freed
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
Allocate Port Service[0000:00:1c.4:pcie03]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
Allocate Port Service[0000:00:1c.5:pcie03]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:07' and the driver 'serial'
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
ahci 0000:00:1f.2: version 2.1
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000016100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/133 cmd 0xffffc20000016180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata3: SATA max UDMA/133 cmd 0xffffc20000016200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata4: SATA max UDMA/133 cmd 0xffffc20000016280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata5: SATA max UDMA/133 cmd 0xffffc20000016300 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata6: SATA max UDMA/133 cmd 0xffffc20000016380 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
ata1.00: ATA-7: ST3500630AS, 3.AAE, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
ata2.00: ATA-7: ST3500630AS, 3.AAE, max UDMA/133
ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
ata2.00: configured for UDMA/133
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata3.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata3.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata4.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata4.00: configured for UDMA/133
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata5.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata5.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata5.00: configured for UDMA/133
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata6.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata6.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata6.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:04:00.0 to 64
scsi6 : ahci
scsi7 : ahci
ata7: SATA max UDMA/133 cmd 0xffffc20000018100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata8: SATA max UDMA/133 cmd 0xffffc20000018180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata8.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata8.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata8.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata8.00: configured for UDMA/133
scsi 7:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:04:00.1 to 64
scsi8 : pata_jmicron
scsi9 : pata_jmicron
ata9: PATA max UDMA/100 cmd 0x0000000000019000 ctl 0x0000000000019402 bmdma 0x000000000001a000 irq 0
ata10: PATA max UDMA/100 cmd 0x0000000000019800 ctl 0x0000000000019c02 bmdma 0x000000000001a008 irq 0
ata9.00: ATAPI, max UDMA/33
ata9.00: configured for UDMA/33
ATA: abnormal status 0x7F on port 0x0000000000019807
scsi 8:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S182M SB03 PQ: 0 ANSI: 5
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 204k freed
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Processor [CPU1] (supports 2 throttling states)
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sda: p1 exceeds device capacity
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: unknown partition table
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sdc: p1 exceeds device capacity
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: unknown partition table
sd 3:0:0:0: [sdd] Attached SCSI disk
sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: unknown partition table
sd 4:0:0:0: [sde] Attached SCSI disk
sd 5:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB)
sd 5:0:0:0: [sdf] Write Protect is off
sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB)
sd 5:0:0:0: [sdf] Write Protect is off
sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf:<6>USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sdf1
sdf: p1 exceeds device capacity
sd 5:0:0:0: [sdf] Attached SCSI disk
sd 7:0:0:0: [sdg] 625142448 512-byte hardware sectors (320073 MB)
sd 7:0:0:0: [sdg] Write Protect is off
sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 7:0:0:0: [sdg] 625142448 512-byte hardware sectors (320073 MB)
sd 7:0:0:0: [sdg] Write Protect is off
sd 7:0:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 7:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg:sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 8:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 4:0:0:0: Attached scsi generic sg4 type 0
sd 5:0:0:0: Attached scsi generic sg5 type 0
sd 7:0:0:0: Attached scsi generic sg6 type 0
sr 8:0:0:0: Attached scsi generic sg7 type 5
sdg1 sdg2 sdg3
sd 7:0:0:0: [sdg] Attached SCSI disk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
attempt to access beyond end of device
sda: rw=0, want=1953533832, limit=976773168
Buffer I/O error on device sda1, logical block 244191472
attempt to access beyond end of device
sda: rw=0, want=1953533832, limit=976773168
Buffer I/O error on device sda1, logical block 244191472
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
Buffer I/O error on device sda1, logical block 244191487
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
Buffer I/O error on device sda1, logical block 244191487
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
Buffer I/O error on device sda1, logical block 244191487
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
Buffer I/O error on device sda1, logical block 244191487
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
Buffer I/O error on device sda1, logical block 244191487
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
Buffer I/O error on device sda1, logical block 244191487
attempt to access beyond end of device
sda: rw=0, want=1953533896, limit=976773168
Buffer I/O error on device sda1, logical block 244191480
attempt to access beyond end of device
sda: rw=0, want=1953533944, limit=976773168
Buffer I/O error on device sda1, logical block 244191486
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
attempt to access beyond end of device
sdf: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410888, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410936, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410888, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410936, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9205000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[f9104000-f91047ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9204000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c800
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000cc00
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usb 3-1: new high speed USB device using ehci_hcd and address 2
Attempting manual resume
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-01:1023] GUID[0016e60000bb7d74]
usb 7-1: new low speed USB device using uhci_hcd and address 2
usb 7-1: configuration #1 chosen from 1 choice
attempt to access beyond end of device
sdf: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410888, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410936, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdf: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410824, limit=625142448
attempt to access beyond end of device
sda: rw=0, want=1953533832, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533832, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410888, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410936, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
attempt to access beyond end of device
sdc: rw=0, want=1875410944, limit=625142448
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533896, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533944, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
attempt to access beyond end of device
sda: rw=0, want=1953533952, limit=976773168
usb 7-2: new full speed USB device using uhci_hcd and address 3
agpgart: Detected an Intel 965G Chipset.
agpgart: AGP aperture is 256M @ 0x0
usb 7-2: configuration #1 chosen from 1 choice
hub 7-2:1.0: USB hub found
hub 7-2:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
sky2 0000:03:00.0: v1.14 addr 0xf8000000 irq 16 Yukon-EC (0xb6) rev 2
sky2 eth0: addr 00:16:e6:88:62:d5
input: PC Speaker as /class/input/input0
usb 3-1.1: new high speed USB device using ehci_hcd and address 4
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
usb 3-1.1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
Initializing USB Mass Storage driver...
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
usb 1-2: new full speed USB device using uhci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 20
usb 7-2.1: new low speed USB device using uhci_hcd and address 4
hiddev96: USB HID v1.11 Device [Belkin Belkin UPS] on usb-0000:00:1d.2-1
usb 7-2.1: configuration #1 chosen from 1 choice
scsi10 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input1
input: USB HID v1.11 Keyboard [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:1d.2-2.1
input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input2
input: USB HID v1.11 Device [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:1d.2-2.1
input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input3
input: USB HID v1.10 Mouse [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:1d.2-2.1
usbcore: registered new interface driver usbhid
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
/usr/src/linux-2.6.22-rc2/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Adding 262136k swap on /dev/sdg2. Priority:-1 extents:1 across:262136k
EXT3 FS on sdg3, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected]
sky2 eth1: enabling interface
sky2 eth1: ram buffer 48K
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
