I'm testing Linux kernel version 2.6.22-rc1 using Debian Testing on an Acer Ferrari 3400 Laptop. This has a VIA IDE controller with the internal HDD and DVD writer attached. The via_pata module and SCSI disk support is compiled into the kernel and the old ATA subsystem is not. At bootup the log messages state that the main HDD is detected as being connected using a 40-pin cable which causes its speed to be limited to UDMA33 rather then UDMA100, the limit of the HD. This works fine under the old ATA system.
I've attached the output of 'dmesg', 'lspci -vvnn' and 'lshw' to this file.
Please let me know if I can provide more information and please CC me on any responses.
Many thanks,
Francis Russell
0x342
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2004.732 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1294252k/1309632k available (2072k kernel code, 14224k reserved, 714k data, 196k init, 392128k highmem)
virtual kernel memory layout:
fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc03bc000 - 0xc03ed000 ( 196 kB)
.data : 0xc030618f - 0xc03b8b94 ( 714 kB)
.text : 0xc0100000 - 0xc030618f (2072 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4011.53 BogoMIPS (lpj=2005765)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Mobile AMD Athlon 64 Processor 3000+ stepping 00
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd64c, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 8100-810f claimed by vt8235 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *5, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *9, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *5, disabled.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 12 14 15) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.20 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:05: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:05: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:05: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:05: iomem range 0xffee0000-0xffefffff has been reserved
pnp: 00:06: ioport range 0x600-0x60f has been reserved
pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:06: ioport range 0xfe10-0xfe11 has been reserved
pnp: 00:06: ioport range 0xfe00-0xfe00 has been reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: 2000-2fff
MEM window: d0100000-d01fffff
PREFETCH window: d8000000-dfffffff
PCI: Bus 2, cardbus bridge: 0000:00:07.0
IO window: 00001c00-00001cff
IO window: 00003000-000030ff
PREFETCH window: 60000000-63ffffff
MEM window: 64000000-67ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x37 set to 0x80
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:01:00.0
vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 5742k, total 131072k
vesafb: mode is 1400x1050x16, linelength=2800, pages=44
vesafb: protected mode interface info at c000:56ac
vesafb: pmi: set display start = c00c571a, set palette = c00c5754
vesafb: pmi: ports = 2010 2016 2054 2038 203c 205c 2000 2004 20b0 20b2 20b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 175x65
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.102 (c) Dave Jones
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
tg3.c:v3.76 (May 5, 2007)
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 16
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:c0:9f:67:01:5f
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
pata_via 0000:00:11.1: version 0.3.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011860 irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011868 irq 15
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: ATA-6: HTS721010G9AT00, MCZOA51A, max UDMA/100
ata1.00: 195371568 sectors, multi 16: LBA48
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: configured for UDMA/33
Switched to high resolution mode on CPU 0
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA HTS721010G9AT00 MCZO PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-835S GQM5 PQ: 0 ANSI: 5
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[email protected]>
ieee80211_crypt: registered algorithm 'NULL'
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 196k freed
Real Time Clock Driver v1.12ac
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
irda_init()
NET: Registered protocol family 23
input: PC Speaker as /class/input/input1
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 17
ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda caddy
USB Universal Host Controller Interface driver v3.0
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ipw2200: Detected geography ZZE (13 802.11bg channels, 19 802.11a channels)
IrDA: Registered device irda0
nsc-ircc, Found dongle: HP HSDL-1100/HSDL-2100
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xe0000000
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 18, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 18, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sr 1:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 18
usb 1-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 18, io base 0x00001840
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: SynPS/2 Synaptics TouchPad as /class/input/input2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 18, io mem 0xd0015800
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-1: USB disconnect, address 2
Yenta: CardBus bridge found at 0000:00:07.0 [1025:0057]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:07.0, mfunc 0x007c1b22, devctl 0x44
Yenta: ISA IRQ mask 0x0a70, PCI irq 16
Socket status: 30000086
ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 18 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d0015000-d00157ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:11.6 to 64
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 3-1: new full speed USB device using uhci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f0000304fb1]
usb 3-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: ata_hpa_resize 1: sectors = 195371568, hpa_sectors = 195371568
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Adding 1566328k swap on /dev/sda3. Priority:-1 extents:1 across:1566328k
EXT3 FS on sda4, internal journal
loop: module loaded
fuse init (API version 7.8)
ACPI: CPU0 (power states: C1[C1] C2[C2])
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
powernow-k8: Found 1 Mobile AMD Athlon 64 Processor 3000+ processors (version 2.00.00)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xc
powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0xe
powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x17
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected]
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access Generic Flash R/W 2002 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
ieee80211_crypt: registered algorithm 'TKIP'
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
ACPI: Thermal Zone [THRM] (46 C)
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
PM: Writing back config space on device 0000:00:0b.0 at offset b (was 3ed173b, writing 571025)
PM: Writing back config space on device 0000:00:0b.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:00:0b.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:00:0b.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:00:0b.0 at offset 0 (was 3ed173b, writing 169c14e4)
Clocksource tsc unstable (delta = -66479724 ns)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[drm] Initialized radeon 1.27.0 20060524 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
eth1: no IPv6 routers present
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge [1106:3188] (rev 01)
Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge [1106:3188]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [80] AGP version 3.5
Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] [1106:b188] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: d8000000-dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 CardBus bridge [0607]: Texas Instruments PCI4510 PC card Cardbus Controller [104c:ac44] (rev 02)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 68000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 60000000-63fff000 (prefetchable)
Memory window 1: 64000000-67fff000
I/O window 0: 00001c00-00001cff
I/O window 1: 00003000-000030ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:07.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4510 IEEE-1394 Controller [104c:8029] (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d0015000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0010000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:09.0 Network controller [0280]: Intel Corporation PRO/Wireless 2915ABG Network Connection [8086:4223] (rev 05)
Subsystem: Intel Corporation Unknown device [8086:1001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d0014000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
00:0b.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet [14e4:169c] (rev 03)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: fefffffffffafff4 Data: bfff
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 4: I/O ports at 1800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 1820 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 82) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 18
Region 0: Memory at d0015800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177]
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 1860 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 50)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 20
Region 0: I/O ports at 1000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.6 Communication controller [0780]: VIA Technologies, Inc. AC'97 Modem Controller [1106:3068] (rev 80)
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 20
Region 0: I/O ports at 1400 [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI] Unknown device [1025:0057]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
francis
description: Notebook
product: Ferrari 3400
vendor: Acer,Inc.
version: Not Applicable
serial: LXFR305002451009A7EF22
width: 32 bits
capabilities: smbios-2.3 dmi-2.3
configuration: administrator_password=enabled boot=oem-specific chassis=notebook frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=80CCB12F-2B64-0010-B169-00C09F67015F
*-core
description: Motherboard
product: Ferrari 3400
vendor: Acer,Inc.
physical id: 0
version: Not Applicable
serial: None
*-firmware
description: BIOS
vendor: Acer
physical id: 0
version: 3C23 (10/19/04)
size: 121KB
capacity: 448KB
capabilities: isa pci pcmcia pnp upgrade shadowing escd cdboot bootselect socketedrom int5printscreen int9keyboard int14serial int17printer int10video acpi usb agp smartbattery biosbootspecification
*-cpu
description: CPU
product: Mobile AMD Athlon 64 Processor 3000+
vendor: Advanced Micro Devices [AMD]
physical id: 4
bus info: cpu@0
version: 15.12.0
slot: Socket A
size: 800MHz
capacity: 2500MHz
width: 64 bits
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt x86-64 3dnowext 3dnow ts fid vid ttp cpufreq
*-cache:0
description: L1 cache
physical id: 8
slot: L1 Cache
size: 128KB
capabilities: asynchronous internal write-back
*-cache:1
description: L2 cache
physical id: 9
slot: L2 Cache
size: 512KB
capacity: 512KB
capabilities: synchronous external write-back unified
*-memory
description: System Memory
physical id: 12
slot: System board or motherboard
size: 1264MB
*-bank:0
description: DIMM DRAM Synchronous
physical id: 0
slot: S1
size: 256MB
width: 32 bits
*-bank:1
description: DIMM DRAM Synchronous [empty]
physical id: 1
slot: S2
width: 32 bits
*-pci:0
description: Host bridge
product: VT8385 [K8T800 AGP] Host Bridge
vendor: VIA Technologies, Inc.
physical id: e0000000
bus info: pci@00:00.0
version: 01
width: 32 bits
clock: 66MHz
configuration: latency=8
resources: iomemory:e0000000-efffffff
*-pci
description: PCI bridge
product: VT8237 PCI bridge [K8T800/K8T890 South]
vendor: VIA Technologies, Inc.
physical id: 1
bus info: pci@00:01.0
version: 00
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master cap_list
*-display
description: VGA compatible controller
product: RV350 [Mobility Radeon 9600 M10]
vendor: ATI Technologies Inc
physical id: 0
bus info: pci@01:00.0
logical name: /dev/fb0
version: 00
size: 128MB
width: 32 bits
clock: 66MHz
capabilities: vga bus_master cap_list fb
configuration: depth=16 frequency=77.44Hz latency=66 mingnt=8 mode=1400x1050 visual=truecolor xres=1400 yres=1050
resources: iomemory:d8000000-dfffffff ioport:2000-20ff iomemory:d0100000-d010ffff irq:21
*-pcmcia
description: CardBus bridge
product: PCI4510 PC card Cardbus Controller
vendor: Texas Instruments
physical id: 7
bus info: pci@00:07.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pcmcia bus_master cap_list
configuration: driver=yenta_cardbus latency=176 maxlatency=5 mingnt=192
resources: iomemory:68000000-68000fff irq:16
*-firewire
description: FireWire (IEEE 1394)
product: PCI4510 IEEE-1394 Controller
vendor: Texas Instruments
physical id: 7.1
bus info: pci@00:07.1
version: 00
width: 32 bits
clock: 33MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci1394 latency=64 maxlatency=4 mingnt=3
resources: iomemory:d0015000-d00157ff iomemory:d0010000-d0013fff irq:19
*-network:0
description: Wireless interface
product: PRO/Wireless 2915ABG Network Connection
vendor: Intel Corporation
physical id: 9
bus info: pci@00:09.0
logical name: eth1
version: 05
serial: 00:12:f0:26:ba:5f
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=ipw2200 driverversion=1.2.0kmprq firmware=ABG:9.0.2.6 (Mar 22 2005) ip=192.168.0.2 latency=64 link=yes maxlatency=24 mingnt=3 multicast=yes wireless=IEEE 802.11g
resources: iomemory:d0014000-d0014fff irq:17
*-network:1
description: Ethernet interface
product: NetXtreme BCM5788 Gigabit Ethernet
vendor: Broadcom Corporation
physical id: b
bus info: pci@00:0b.0
logical name: eth0
version: 03
serial: 00:c0:9f:67:01:5f
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.76 firmware=5788-v3.03 latency=64 link=no mingnt=64 multicast=yes port=twisted pair
resources: iomemory:d0000000-d000ffff irq:16
*-usb:0
description: USB Controller
product: VT82xxxxx UHCI USB 1.1 Controller
vendor: VIA Technologies, Inc.
physical id: 10
bus info: pci@00:10.0
version: 80
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master cap_list
configuration: driver=uhci_hcd latency=64
resources: ioport:1800-181f irq:18
*-usb:1
description: USB Controller
product: VT82xxxxx UHCI USB 1.1 Controller
vendor: VIA Technologies, Inc.
physical id: 10.1
bus info: pci@00:10.1
version: 80
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master cap_list
configuration: driver=uhci_hcd latency=64
resources: ioport:1820-183f irq:18
*-usb:2
description: USB Controller
product: VT82xxxxx UHCI USB 1.1 Controller
vendor: VIA Technologies, Inc.
physical id: 10.2
bus info: pci@00:10.2
version: 80
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master cap_list
configuration: driver=uhci_hcd latency=64
resources: ioport:1840-185f irq:18
*-usb:3
description: USB Controller
product: USB 2.0
vendor: VIA Technologies, Inc.
physical id: 10.3
bus info: pci@00:10.3
version: 82
width: 32 bits
clock: 33MHz
capabilities: ehci bus_master cap_list
configuration: driver=ehci_hcd latency=64
resources: iomemory:d0015800-d00158ff irq:18
*-isa
description: ISA bridge
product: VT8235 ISA Bridge
vendor: VIA Technologies, Inc.
physical id: 11
bus info: pci@00:11.0
version: 00
width: 32 bits
clock: 33MHz
capabilities: isa bus_master cap_list
configuration: latency=0
*-ide
description: IDE interface
product: VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE
vendor: VIA Technologies, Inc.
physical id: 11.1
bus info: pci@00:11.1
logical name: scsi0
logical name: scsi1
version: 06
width: 32 bits
clock: 33MHz
capabilities: ide bus_master cap_list emulated
configuration: driver=pata_via latency=64
resources: iomemory:1f0-1f7 iomemory:3f0-3ef iomemory:170-177 iomemory:370-36f ioport:1860-186f
*-disk
description: SCSI Disk
product: HTS721010G9AT00
vendor: ATA
physical id: 0
bus info: scsi@0:0.0.0
logical name: /dev/sda
version: MCZO
serial: MPC0N2Y0GTJY2H
size: 93GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume:0
description: Linux filesystem partition
physical id: 1
bus info: scsi@0:0.0.0,1
logical name: /dev/sda1
capacity: 101MB
capabilities: primary
*-volume:1
description: HPFS/NTFS partition
physical id: 2
bus info: scsi@0:0.0.0,2
logical name: /dev/sda2
capacity: 40GB
capabilities: primary bootable
*-volume:2
description: Linux swap / Solaris partition
physical id: 3
bus info: scsi@0:0.0.0,3
logical name: /dev/sda3
capacity: 1529MB
capabilities: primary nofs
*-volume:3
description: Linux filesystem partition
physical id: 4
bus info: scsi@0:0.0.0,4
logical name: /dev/sda4
capacity: 51GB
capabilities: primary
*-cdrom
description: DVD-RAM writer
product: DVD-RAM UJ-835S
vendor: MATSHITA
physical id: 1
bus info: scsi@1:0.0.0
logical name: /dev/cdrom1
logical name: /dev/dvd1
logical name: /dev/scd0
logical name: /dev/sr0
version: GQM5
capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram
configuration: ansiversion=5
*-disc
physical id: 0
logical name: /dev/cdrom1
*-multimedia
description: Multimedia audio controller
product: VT8233/A/8235/8237 AC97 Audio Controller
vendor: VIA Technologies, Inc.
physical id: 11.5
bus info: pci@00:11.5
version: 50
width: 32 bits
clock: 33MHz
capabilities: cap_list
configuration: driver=VIA 82xx Audio latency=0
resources: ioport:1000-10ff irq:20
*-communication
description: Communication controller
product: AC'97 Modem Controller
vendor: VIA Technologies, Inc.
physical id: 11.6
bus info: pci@00:11.6
version: 80
width: 32 bits
clock: 33MHz
capabilities: cap_list
configuration: driver=VIA 82xx Modem latency=0
resources: ioport:1400-14ff irq:20
*-pci:1
description: Host bridge
product: K8 [Athlon64/Opteron] HyperTransport Technology Configuration
vendor: Advanced Micro Devices [AMD]
physical id: 100
bus info: pci@00:18.0
version: 00
width: 32 bits
clock: 33MHz
*-pci:2
description: Host bridge
product: K8 [Athlon64/Opteron] Address Map
vendor: Advanced Micro Devices [AMD]
physical id: 101
bus info: pci@00:18.1
version: 00
width: 32 bits
clock: 33MHz
*-pci:3
description: Host bridge
product: K8 [Athlon64/Opteron] DRAM Controller
vendor: Advanced Micro Devices [AMD]
physical id: 102
bus info: pci@00:18.2
version: 00
width: 32 bits
clock: 33MHz
*-pci:4
description: Host bridge
product: K8 [Athlon64/Opteron] Miscellaneous Control
vendor: Advanced Micro Devices [AMD]
physical id: 103
bus info: pci@00:18.3
version: 00
width: 32 bits
clock: 33MHz
*-scsi
physical id: 1
bus info: usb@3:1
logical name: scsi2
capabilities: emulated scsi-host
configuration: driver=usb-storage
*-disk
description: SCSI Disk
product: Flash R/W
vendor: Generic
physical id: 0.0.0
bus info: scsi@2:0.0.0
logical name: /dev/sdb
version: 2002
serial: ST7265-2002
capabilities: removable
configuration: ansiversion=2
*-disc
physical id: 0
logical name: /dev/sdb
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
