Hello linux-kernel,
Intro: This is a header with hardware definitions for ASIC3 chip,
contributed by HP/Compaq. It is provided as-is, as a vendor-originated
header.
---------
ipaq-asic3.h: Hardware definitions for ASIC3 chip, found in ~12
handheld devices from HP/Compaq and HTC.
Signed-off-by: Paul Sokolovsky <[email protected]>
include/asm-arm/hardware/ipaq-asic3.h | 609 +++++++++++++++++++++++++++++++++
1 files changed, 609 insertions(+), 0 deletions(-)
diff --git a/include/asm-arm/hardware/ipaq-asic3.h b/include/asm-arm/hardware/ipaq-asic3.h
new file mode 100644
index 0000000..789bb16
--- /dev/null
+++ b/include/asm-arm/hardware/ipaq-asic3.h
@@ -0,0 +1,609 @@
+/*
+ *
+ * Definitions for the HTC ASIC3 chip found in several handheld devices
+ *
+ * Copyright 2001 Compaq Computer Corporation.
+ *
+ * Use consistent with the GNU GPL is permitted,
+ * provided that this copyright notice is
+ * preserved in its entirety in all copies and derived works.
+ *
+ * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
+ * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
+ * FITNESS FOR ANY PARTICULAR PURPOSE.
+ *
+ * Author: Andrew Christian
+ *
+ */
+
+#ifndef IPAQ_ASIC3_H
+#define IPAQ_ASIC3_H
+
+/****************************************************/
+/* IPAQ, ASIC #3, replaces ASIC #1 */
+
+#define IPAQ_ASIC3(_b,s,x,y) \
+ (*((volatile s *) (_b + _IPAQ_ASIC3_ ## x ## _Base + (_IPAQ_ASIC3_ ## x ## _ ## y))))
+#define IPAQ_ASIC3_N(_b,s,x,y,z) \
+ (*((volatile s *) (_b + _IPAQ_ASIC3_ ## x ## _ ## y ## _Base + (_IPAQ_ASIC3_ ## x ## _ ## z))))
+
+#define IPAQ_ASIC3_GPIO(_b,s,x,y) \
+ (*((volatile s *) (_b + _IPAQ_ASIC3_GPIO_ ## x ## _Base + (_IPAQ_ASIC3_GPIO_ ## y))))
+
+#define IPAQ_ASIC3_OFFSET(x,y) (_IPAQ_ASIC3_ ## x ## _Base + _IPAQ_ASIC3_ ## x ## _ ## y)
+#define IPAQ_ASIC3_GPIO_OFFSET(x,y) (_IPAQ_ASIC3_GPIO_ ## x ## _Base + _IPAQ_ASIC3_GPIO_ ## y)
+
+
+/* All offsets below are specified with this address bus shift */
+#define ASIC3_DEFAULT_ADDR_SHIFT 2
+
+#define _IPAQ_ASIC3_GPIO_A_Base 0x0000
+#define _IPAQ_ASIC3_GPIO_B_Base 0x0100
+#define _IPAQ_ASIC3_GPIO_C_Base 0x0200
+#define _IPAQ_ASIC3_GPIO_D_Base 0x0300
+
+#define _IPAQ_ASIC3_GPIO_Mask 0x00 /* R/W 0:don't mask, 1:mask interrupt */
+#define _IPAQ_ASIC3_GPIO_Direction 0x04 /* R/W 0:input, 1:output */
+#define _IPAQ_ASIC3_GPIO_Out 0x08 /* R/W 0:output low, 1:output high */
+#define _IPAQ_ASIC3_GPIO_TriggerType 0x0c /* R/W 0:level, 1:edge */
+#define _IPAQ_ASIC3_GPIO_EdgeTrigger 0x10 /* R/W 0:falling, 1:rising */
+#define _IPAQ_ASIC3_GPIO_LevelTrigger 0x14 /* R/W 0:low, 1:high level detect */
+#define _IPAQ_ASIC3_GPIO_SleepMask 0x18 /* R/W 0:don't mask, 1:mask trigger in sleep mode */
+#define _IPAQ_ASIC3_GPIO_SleepOut 0x1c /* R/W level 0:low, 1:high in sleep mode */
+#define _IPAQ_ASIC3_GPIO_BattFaultOut 0x20 /* R/W level 0:low, 1:high in batt_fault */
+#define _IPAQ_ASIC3_GPIO_IntStatus 0x24 /* R/W 0:none, 1:detect */
+#define _IPAQ_ASIC3_GPIO_AltFunction 0x28 /* R/W 0:normal control 1:LED register control */
+#define _IPAQ_ASIC3_GPIO_SleepConf 0x2c /* R/W bit 1: autosleep 0: disable gposlpout in normal mode, enable gposlpout in sleep mode */
+#define _IPAQ_ASIC3_GPIO_Status 0x30 /* R Pin status */
+
+#define IPAQ_ASIC3_GPIO_A_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, A, Mask )
+#define IPAQ_ASIC3_GPIO_A_DIR(_b) IPAQ_ASIC3_GPIO( _b, u16, A, Direction )
+#define IPAQ_ASIC3_GPIO_A_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, A, Out )
+#define IPAQ_ASIC3_GPIO_A_LEVELTRI(_b) IPAQ_ASIC3_GPIO( _b, u16, A, TriggerType )
+#define IPAQ_ASIC3_GPIO_A_RISING(_b) IPAQ_ASIC3_GPIO( _b, u16, A, EdgeTrigger )
+#define IPAQ_ASIC3_GPIO_A_LEVEL(_b) IPAQ_ASIC3_GPIO( _b, u16, A, LevelTrigger )
+#define IPAQ_ASIC3_GPIO_A_SLEEP_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, A, SleepMask )
+#define IPAQ_ASIC3_GPIO_A_SLEEP_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, A, SleepOut )
+#define IPAQ_ASIC3_GPIO_A_BATT_FAULT_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, A, BattFaultOut )
+#define IPAQ_ASIC3_GPIO_A_INT_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, A, IntStatus )
+#define IPAQ_ASIC3_GPIO_A_ALT_FUNCTION(_b) IPAQ_ASIC3_GPIO( _b, u16, A, AltFunction )
+#define IPAQ_ASIC3_GPIO_A_SLEEP_CONF(_b) IPAQ_ASIC3_GPIO( _b, u16, A, SleepConf )
+#define IPAQ_ASIC3_GPIO_A_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, A, Status )
+
+#define IPAQ_ASIC3_GPIO_B_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, B, Mask )
+#define IPAQ_ASIC3_GPIO_B_DIR(_b) IPAQ_ASIC3_GPIO( _b, u16, B, Direction )
+#define IPAQ_ASIC3_GPIO_B_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, B, Out )
+#define IPAQ_ASIC3_GPIO_B_LEVELTRI(_b) IPAQ_ASIC3_GPIO( _b, u16, B, TriggerType )
+#define IPAQ_ASIC3_GPIO_B_RISING(_b) IPAQ_ASIC3_GPIO( _b, u16, B, EdgeTrigger )
+#define IPAQ_ASIC3_GPIO_B_LEVEL(_b) IPAQ_ASIC3_GPIO( _b, u16, B, LevelTrigger )
+#define IPAQ_ASIC3_GPIO_B_SLEEP_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, B, SleepMask )
+#define IPAQ_ASIC3_GPIO_B_SLEEP_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, B, SleepOut )
+#define IPAQ_ASIC3_GPIO_B_BATT_FAULT_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, B, BattFaultOut )
+#define IPAQ_ASIC3_GPIO_B_INT_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, B, IntStatus )
+#define IPAQ_ASIC3_GPIO_B_ALT_FUNCTION(_b) IPAQ_ASIC3_GPIO( _b, u16, B, AltFunction )
+#define IPAQ_ASIC3_GPIO_B_SLEEP_CONF(_b) IPAQ_ASIC3_GPIO( _b, u16, B, SleepConf )
+#define IPAQ_ASIC3_GPIO_B_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, B, Status )
+
+#define IPAQ_ASIC3_GPIO_C_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, C, Mask )
+#define IPAQ_ASIC3_GPIO_C_DIR(_b) IPAQ_ASIC3_GPIO( _b, u16, C, Direction )
+#define IPAQ_ASIC3_GPIO_C_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, C, Out )
+#define IPAQ_ASIC3_GPIO_C_LEVELTRI(_b) IPAQ_ASIC3_GPIO( _b, u16, C, TriggerType )
+#define IPAQ_ASIC3_GPIO_C_RISING(_b) IPAQ_ASIC3_GPIO( _b, u16, C, EdgeTrigger )
+#define IPAQ_ASIC3_GPIO_C_LEVEL(_b) IPAQ_ASIC3_GPIO( _b, u16, C, LevelTrigger )
+#define IPAQ_ASIC3_GPIO_C_SLEEP_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, C, SleepMask )
+#define IPAQ_ASIC3_GPIO_C_SLEEP_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, C, SleepOut )
+#define IPAQ_ASIC3_GPIO_C_BATT_FAULT_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, C, BattFaultOut )
+#define IPAQ_ASIC3_GPIO_C_INT_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, C, IntStatus )
+#define IPAQ_ASIC3_GPIO_C_ALT_FUNCTION(_b) IPAQ_ASIC3_GPIO( _b, u16, C, AltFunction )
+#define IPAQ_ASIC3_GPIO_C_SLEEP_CONF(_b) IPAQ_ASIC3_GPIO( _b, u16, C, SleepConf )
+#define IPAQ_ASIC3_GPIO_C_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, C, Status )
+
+#define IPAQ_ASIC3_GPIO_D_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, D, Mask )
+#define IPAQ_ASIC3_GPIO_D_DIR(_b) IPAQ_ASIC3_GPIO( _b, u16, D, Direction )
+#define IPAQ_ASIC3_GPIO_D_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, D, Out )
+#define IPAQ_ASIC3_GPIO_D_LEVELTRI(_b) IPAQ_ASIC3_GPIO( _b, u16, D, TriggerType )
+#define IPAQ_ASIC3_GPIO_D_RISING(_b) IPAQ_ASIC3_GPIO( _b, u16, D, EdgeTrigger )
+#define IPAQ_ASIC3_GPIO_D_LEVEL(_b) IPAQ_ASIC3_GPIO( _b, u16, D, LevelTrigger )
+#define IPAQ_ASIC3_GPIO_D_SLEEP_MASK(_b) IPAQ_ASIC3_GPIO( _b, u16, D, SleepMask )
+#define IPAQ_ASIC3_GPIO_D_SLEEP_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, D, SleepOut )
+#define IPAQ_ASIC3_GPIO_D_BATT_FAULT_OUT(_b) IPAQ_ASIC3_GPIO( _b, u16, D, BattFaultOut )
+#define IPAQ_ASIC3_GPIO_D_INT_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, D, IntStatus )
+#define IPAQ_ASIC3_GPIO_D_ALT_FUNCTION(_b) IPAQ_ASIC3_GPIO( _b, u16, D, AltFunction )
+#define IPAQ_ASIC3_GPIO_D_SLEEP_CONF(_b) IPAQ_ASIC3_GPIO( _b, u16, D, SleepConf )
+#define IPAQ_ASIC3_GPIO_D_STATUS(_b) IPAQ_ASIC3_GPIO( _b, u16, D, Status )
+
+#define _IPAQ_ASIC3_SPI_Base 0x0400
+#define _IPAQ_ASIC3_SPI_Control 0x0000
+#define _IPAQ_ASIC3_SPI_TxData 0x0004
+#define _IPAQ_ASIC3_SPI_RxData 0x0008
+#define _IPAQ_ASIC3_SPI_Int 0x000c
+#define _IPAQ_ASIC3_SPI_Status 0x0010
+
+#define IPAQ_ASIC3_SPI_Control(_b) IPAQ_ASIC3( _b, u16, SPI, Control )
+#define IPAQ_ASIC3_SPI_TxData(_b) IPAQ_ASIC3( _b, u16, SPI, TxData )
+#define IPAQ_ASIC3_SPI_RxData(_b) IPAQ_ASIC3( _b, u16, SPI, RxData )
+#define IPAQ_ASIC3_SPI_Int(_b) IPAQ_ASIC3( _b, u16, SPI, Int )
+#define IPAQ_ASIC3_SPI_Status(_b) IPAQ_ASIC3( _b, u16, SPI, Status )
+
+#define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */
+
+#define _IPAQ_ASIC3_PWM_0_Base 0x0500
+#define _IPAQ_ASIC3_PWM_1_Base 0x0600
+#define _IPAQ_ASIC3_PWM_TimeBase 0x0000
+#define _IPAQ_ASIC3_PWM_PeriodTime 0x0004
+#define _IPAQ_ASIC3_PWM_DutyTime 0x0008
+
+#define IPAQ_ASIC3_PWM_TimeBase(_b, x) IPAQ_ASIC3_N( _b, u16, PWM, x, TimeBase )
+#define IPAQ_ASIC3_PWM_PeriodTime(_b, x) IPAQ_ASIC3_N( _b, u16, PWM, x, PeriodTime )
+#define IPAQ_ASIC3_PWM_DutyTime(_b, x) IPAQ_ASIC3_N( _b, u16, PWM, x, DutyTime )
+
+#define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */
+#define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */
+
+#define _IPAQ_ASIC3_LED_0_Base 0x0700
+#define _IPAQ_ASIC3_LED_1_Base 0x0800
+#define _IPAQ_ASIC3_LED_2_Base 0x0900
+#define _IPAQ_ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */
+#define _IPAQ_ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */
+#define _IPAQ_ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */
+#define _IPAQ_ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */
+
+#define IPAQ_ASIC3_LED_TimeBase(_b, x) IPAQ_ASIC3_N( _b, u8, LED, x, TimeBase )
+#define IPAQ_ASIC3_LED_PeriodTime(_b, x) IPAQ_ASIC3_N( _b, u16, LED, x, PeriodTime )
+#define IPAQ_ASIC3_LED_DutyTime(_b, x) IPAQ_ASIC3_N( _b, u16, LED, x, DutyTime )
+#define IPAQ_ASIC3_LED_AutoStopCount(_b, x) IPAQ_ASIC3_N( _b, u16, LED, x, AutoStopCount )
+
+/* LED TimeBase bits - match ASIC2 */
+#define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */
+ /* Note: max = 5 on hx4700 */
+ /* 0: maximum time base */
+ /* 1: maximum time base / 2 */
+ /* n: maximum time base / 2^n */
+
+#define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */
+#define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop set 0:disable, 1:enable */
+#define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */
+
+#define _IPAQ_ASIC3_CLOCK_Base 0x0A00
+#define _IPAQ_ASIC3_CLOCK_CDEX 0x00
+#define _IPAQ_ASIC3_CLOCK_SEL 0x04
+
+#define IPAQ_ASIC3_CLOCK_CDEX(_b) IPAQ_ASIC3( _b, u16, CLOCK, CDEX )
+#define IPAQ_ASIC3_CLOCK_SEL(_b) IPAQ_ASIC3( _b, u16, CLOCK, SEL )
+
+#define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */
+#define CLOCK_CDEX_SOURCE0 (1 << 0)
+#define CLOCK_CDEX_SOURCE1 (1 << 1)
+#define CLOCK_CDEX_SPI (1 << 2)
+#define CLOCK_CDEX_OWM (1 << 3)
+#define CLOCK_CDEX_PWM0 (1 << 4)
+#define CLOCK_CDEX_PWM1 (1 << 5)
+#define CLOCK_CDEX_LED0 (1 << 6)
+#define CLOCK_CDEX_LED1 (1 << 7)
+#define CLOCK_CDEX_LED2 (1 << 8)
+
+#define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source 24.576M/12.288M */
+#define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source control 24.576M/12.288M */
+#define CLOCK_CDEX_SMBUS (1 << 11)
+#define CLOCK_CDEX_CONTROL_CX (1 << 12)
+
+#define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */
+#define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */
+
+#define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select - 1: 24.576 Mhz, 0: 12.288 MHz */
+#define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select - 1: 24.576 MHz, 0: 12.288 MHz */
+#define CLOCK_SEL_CX (1 << 2) /* R/W: INT clock source control (32.768 kHz) */
+
+
+#define _IPAQ_ASIC3_INTR_Base 0x0B00
+
+#define _IPAQ_ASIC3_INTR_IntMask 0x00 /* Interrupt mask control */
+#define _IPAQ_ASIC3_INTR_PIntStat 0x04 /* Peripheral interrupt status */
+#define _IPAQ_ASIC3_INTR_IntCPS 0x08 /* Interrupt timer clock pre-scale */
+#define _IPAQ_ASIC3_INTR_IntTBS 0x0c /* Interrupt timer set */
+
+#define IPAQ_ASIC3_INTR_IntMask(_b) IPAQ_ASIC3( _b, u8, INTR, IntMask )
+#define IPAQ_ASIC3_INTR_PIntStat(_b) IPAQ_ASIC3( _b, u8, INTR, PIntStat )
+#define IPAQ_ASIC3_INTR_IntCPS(_b) IPAQ_ASIC3( _b, u8, INTR, IntCPS )
+#define IPAQ_ASIC3_INTR_IntTBS(_b) IPAQ_ASIC3( _b, u16, INTR, IntTBS )
+
+#define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global interrupt mask 1:enable */
+#define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */
+#define ASIC3_INTMASK_MASK0 (1 << 2)
+#define ASIC3_INTMASK_MASK1 (1 << 3)
+#define ASIC3_INTMASK_MASK2 (1 << 4)
+#define ASIC3_INTMASK_MASK3 (1 << 5)
+#define ASIC3_INTMASK_MASK4 (1 << 6)
+#define ASIC3_INTMASK_MASK5 (1 << 7)
+
+#define ASIC3_INTR_PERIPHERAL_A (1 << 0)
+#define ASIC3_INTR_PERIPHERAL_B (1 << 1)
+#define ASIC3_INTR_PERIPHERAL_C (1 << 2)
+#define ASIC3_INTR_PERIPHERAL_D (1 << 3)
+#define ASIC3_INTR_LED0 (1 << 4)
+#define ASIC3_INTR_LED1 (1 << 5)
+#define ASIC3_INTR_LED2 (1 << 6)
+#define ASIC3_INTR_SPI (1 << 7)
+#define ASIC3_INTR_SMBUS (1 << 8)
+#define ASIC3_INTR_OWM (1 << 9)
+
+#define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */
+#define ASIC3_INTR_CPS_SET ( 1 << 4 ) /* Time base enable */
+
+
+/* Basic control of the SD ASIC */
+#define _IPAQ_ASIC3_SDHWCTRL_Base 0x0E00
+
+#define _IPAQ_ASIC3_SDHWCTRL_SDConf 0x00
+#define IPAQ_ASIC3_SDHWCTRL_SDConf(_b) IPAQ_ASIC3( _b, u8, SDHWCTRL, SDConf )
+
+#define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */
+#define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */
+#define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */
+#define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* Level of SD card detection: 1:high, 0:low */
+#define ASIC3_SDHWCTRL_LEVWP (1 << 4) /* Level of SD card write protection: 1=low, 0=high */
+#define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 1=enable, 0=disable */
+#define ASIC3_SDHWCTRL_SDPWR (1 << 6) /* SD card power supply control 1=enable */
+
+
+/* This is a pointer to an array of 12 u32 values - but only the lower 2 bytes matter */
+/* Use it as "IPAQ_ASIC3_HWPROTECT_ARRAY[x]" */
+
+#define _IPAQ_ASIC3_HWPROTECT_Base 0x1000
+#define IPAQ_ASIC3_HWPROTECT_ARRAY ((volatile u32*)(_IPAQ_ASIC3_Base + _IPAQ_ASIC3_HWPROTECT_Base))
+#define HWPROTECT_ARRAY_LEN 12
+#define HWPROTECT_ARRAY_VALUES {0x4854,0x432d,0x5344,0x494f,0x2050,0x2f4e,0x3a33,0x3048,0x3830,0x3032,0x382d,0x3030}
+
+
+#define _IPAQ_ASIC3_EXTCF_Base 0x1100
+
+#define _IPAQ_ASIC3_EXTCF_Select 0x00
+#define _IPAQ_ASIC3_EXTCF_Reset 0x04
+
+#define IPAQ_ASIC3_EXTCF_Select(_b) IPAQ_ASIC3( _b, u16, EXTCF, Select )
+#define IPAQ_ASIC3_EXTCF_Reset(_b) IPAQ_ASIC3( _b, u16, EXTCF, Reset )
+
+#define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */
+#define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */
+#define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */
+#define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */
+#define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */
+#define ASIC3_EXTCF_OWM_RESET (1 << 6) /* undocumented, used by OWM and CF */
+#define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state control */
+#define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state control */
+#define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */
+#define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */
+#define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */
+#define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */
+#define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14)
+#define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */
+
+/*****************************************************************************
+ * The Onewire interface registers
+ *
+ * OWM_CMD
+ * OWM_DAT
+ * OWM_INTR
+ * OWM_INTEN
+ * OWM_CLKDIV
+ *
+ *****************************************************************************/
+
+#define _IPAQ_ASIC3_OWM_Base 0xC00
+
+#define _IPAQ_ASIC3_OWM_CMD 0x00
+#define _IPAQ_ASIC3_OWM_DAT 0x04
+#define _IPAQ_ASIC3_OWM_INTR 0x08
+#define _IPAQ_ASIC3_OWM_INTEN 0x0C
+#define _IPAQ_ASIC3_OWM_CLKDIV 0x10
+
+#define ASIC3_OWM_CMD_ONEWR (1 << 0)
+#define ASIC3_OWM_CMD_SRA (1 << 1)
+#define ASIC3_OWM_CMD_DQO (1 << 2)
+#define ASIC3_OWM_CMD_DQI (1 << 3)
+
+#define ASIC3_OWM_INTR_PD (1 << 0)
+#define ASIC3_OWM_INTR_PDR (1 << 1)
+#define ASIC3_OWM_INTR_TBE (1 << 2)
+#define ASIC3_OWM_INTR_TEMP (1 << 3)
+#define ASIC3_OWM_INTR_RBF (1 << 4)
+
+#define ASIC3_OWM_INTEN_EPD (1 << 0)
+#define ASIC3_OWM_INTEN_IAS (1 << 1)
+#define ASIC3_OWM_INTEN_ETBE (1 << 2)
+#define ASIC3_OWM_INTEN_ETMT (1 << 3)
+#define ASIC3_OWM_INTEN_ERBF (1 << 4)
+
+#define ASIC3_OWM_CLKDIV_PRE (3 << 0) /* two bits wide at bit position 0 */
+#define ASIC3_OWM_CLKDIV_DIV (7 << 2) /* 3 bits wide at bit position 2 */
+
+
+/*****************************************************************************
+ * The SD configuration registers are at a completely different location
+ * in memory. They are divided into three sets of registers:
+ *
+ * SD_CONFIG Core configuration register
+ * SD_CTRL Control registers for SD operations
+ * SDIO_CTRL Control registers for SDIO operations
+ *
+ *****************************************************************************/
+
+#define IPAQ_ASIC3_SD_CONFIG(_b, s,x) \
+ (*((volatile s *) ((_b) + _IPAQ_ASIC3_SD_CONFIG_Base + (_IPAQ_ASIC3_SD_CONFIG_ ## x))))
+
+#define _IPAQ_ASIC3_SD_CONFIG_Base 0x0400 // Assumes 32 bit addressing
+
+#define _IPAQ_ASIC3_SD_CONFIG_Command 0x08 /* R/W: Command */
+#define _IPAQ_ASIC3_SD_CONFIG_Addr0 0x20 /* [9:31] SD Control Register Base Address */
+#define _IPAQ_ASIC3_SD_CONFIG_Addr1 0x24 /* [9:31] SD Control Register Base Address */
+#define _IPAQ_ASIC3_SD_CONFIG_IntPin 0x78 /* R/O: interrupt assigned to pin */
+#define _IPAQ_ASIC3_SD_CONFIG_ClkStop 0x80 /* Set to 0x1f to clock SD controller, 0 otherwise. */
+ /* at 0x82 - Gated Clock Control */
+#define _IPAQ_ASIC3_SD_CONFIG_ClockMode 0x84 /* Control clock of SD controller */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_PinStatus 0x88 /* R/0: read status of SD pins */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_Power1 0x90 /* Power1 - manual power control */
+ /* Power2 is at 0x92 - auto power up after card inserted */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_Power3 0x94 /* auto power down when card removed */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_CardDetect 0x98 /* */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_Slot 0xA0 /* R/O: define support slot number */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_ExtGateClk1 0x1E0 /* Could be used for gated clock (don't use) */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_ExtGateClk2 0x1E2 /* Could be used for gated clock (don't use) */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_GPIO_OutAndEnable 0x1E8 /* GPIO Output Reg. , at 0x1EA - GPIO Output Enable Reg. */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_GPIO_Status 0x1EC /* GPIO Status Reg. */
+#define _IPAQ_ASIC3_SD_CONFIG_SDHC_ExtGateClk3 0x1F0 /* Bit 1: double buffer/single buffer */
+
+#define IPAQ_ASIC3_SD_CONFIG_Command(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, Command )
+#define IPAQ_ASIC3_SD_CONFIG_Addr0(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, Addr0 )
+#define IPAQ_ASIC3_SD_CONFIG_Addr1(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, Addr1 )
+#define IPAQ_ASIC3_SD_CONFIG_IntPin(_b) IPAQ_ASIC3_SD_CONFIG(_b, u8, IntPin )
+#define IPAQ_ASIC3_SD_CONFIG_ClkStop(_b) IPAQ_ASIC3_SD_CONFIG(_b, u8, ClkStop )
+#define IPAQ_ASIC3_SD_CONFIG_ClockMode(_b) IPAQ_ASIC3_SD_CONFIG(_b, u8, ClockMode )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_PinStatus(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_PinStatus )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_Power1(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_Power1 )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_Power3(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_Power3 )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_CardDetect(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_CardDetect )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_Slot(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_Slot )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_ExtGateClk1(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_ExtGateClk1 )
+#define IPAQ_ASIC3_SD_CONFIG_SDHC_ExtGateClk3(_b) IPAQ_ASIC3_SD_CONFIG(_b, u16, SDHC_ExtGateClk3 )
+
+#define SD_CONFIG_
+
+#define SD_CONFIG_COMMAND_MAE (1<<1) /* Memory access enable (set to 1 to access SD Controller) */
+
+#define SD_CONFIG_CLK_ENABLE_ALL 0x1f
+
+#define SD_CONFIG_POWER1_PC_33V 0x0200 /* Set for 3.3 volts */
+#define SD_CONFIG_POWER1_PC_OFF 0x0000 /* Turn off power */
+
+#define SD_CONFIG_CARDDETECTMODE_CLK ((x)&0x3) /* two bits - number of cycles for card detection */
+
+
+#define _IPAQ_ASIC3_SD_CTRL_Base 0x1000
+
+#define IPAQ_ASIC3_SD(_b, s,x) \
+ (*((volatile s *) ((_b) + _IPAQ_ASIC3_SD_CTRL_Base + (_IPAQ_ASIC3_SD_CTRL_ ## x))))
+
+#define _IPAQ_ASIC3_SD_CTRL_Cmd 0x00
+#define _IPAQ_ASIC3_SD_CTRL_Arg0 0x08
+#define _IPAQ_ASIC3_SD_CTRL_Arg1 0x0C
+#define _IPAQ_ASIC3_SD_CTRL_StopInternal 0x10
+#define _IPAQ_ASIC3_SD_CTRL_TransferSectorCount 0x14
+#define _IPAQ_ASIC3_SD_CTRL_Response0 0x18
+#define _IPAQ_ASIC3_SD_CTRL_Response1 0x1C
+#define _IPAQ_ASIC3_SD_CTRL_Response2 0x20
+#define _IPAQ_ASIC3_SD_CTRL_Response3 0x24
+#define _IPAQ_ASIC3_SD_CTRL_Response4 0x28
+#define _IPAQ_ASIC3_SD_CTRL_Response5 0x2C
+#define _IPAQ_ASIC3_SD_CTRL_Response6 0x30
+#define _IPAQ_ASIC3_SD_CTRL_Response7 0x34
+#define _IPAQ_ASIC3_SD_CTRL_CardStatus 0x38
+#define _IPAQ_ASIC3_SD_CTRL_BufferCtrl 0x3C
+#define _IPAQ_ASIC3_SD_CTRL_IntMaskCard 0x40
+#define _IPAQ_ASIC3_SD_CTRL_IntMaskBuffer 0x44
+#define _IPAQ_ASIC3_SD_CTRL_CardClockCtrl 0x48
+#define _IPAQ_ASIC3_SD_CTRL_MemCardXferDataLen 0x4C
+#define _IPAQ_ASIC3_SD_CTRL_MemCardOptionSetup 0x50
+#define _IPAQ_ASIC3_SD_CTRL_ErrorStatus0 0x58
+#define _IPAQ_ASIC3_SD_CTRL_ErrorStatus1 0x5C
+#define _IPAQ_ASIC3_SD_CTRL_DataPort 0x60
+#define _IPAQ_ASIC3_SD_CTRL_TransactionCtrl 0x68
+#define _IPAQ_ASIC3_SD_CTRL_SoftwareReset 0x1C0
+
+#define IPAQ_ASIC3_SD_CTRL_Cmd(_b) IPAQ_ASIC3_SD( _b, u16, Cmd ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Arg0(_b) IPAQ_ASIC3_SD( _b, u16, Arg0 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Arg1(_b) IPAQ_ASIC3_SD( _b, u16, Arg1 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_StopInternal(_b) IPAQ_ASIC3_SD( _b, u16, StopInternal ) /* */
+#define IPAQ_ASIC3_SD_CTRL_TransferSectorCount(_b) IPAQ_ASIC3_SD( _b, u16, TransferSectorCount ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response0(_b) IPAQ_ASIC3_SD( _b, u16, Response0 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response1(_b) IPAQ_ASIC3_SD( _b, u16, Response1 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response2(_b) IPAQ_ASIC3_SD( _b, u16, Response2 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response3(_b) IPAQ_ASIC3_SD( _b, u16, Response3 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response4(_b) IPAQ_ASIC3_SD( _b, u16, Response4 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response5(_b) IPAQ_ASIC3_SD( _b, u16, Response5 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response6(_b) IPAQ_ASIC3_SD( _b, u16, Response6 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_Response7(_b) IPAQ_ASIC3_SD( _b, u16, Response7 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_CardStatus(_b) IPAQ_ASIC3_SD( _b, u16, CardStatus ) /* */
+#define IPAQ_ASIC3_SD_CTRL_BufferCtrl(_b) IPAQ_ASIC3_SD( _b, u16, BufferCtrl ) /* and error status*/
+#define IPAQ_ASIC3_SD_CTRL_IntMaskCard(_b) IPAQ_ASIC3_SD( _b, u16, IntMaskCard ) /* */
+#define IPAQ_ASIC3_SD_CTRL_IntMaskBuffer(_b) IPAQ_ASIC3_SD( _b, u16, IntMaskBuffer ) /* */
+#define IPAQ_ASIC3_SD_CTRL_CardClockCtrl(_b) IPAQ_ASIC3_SD( _b, u16, CardClockCtrl ) /* */
+#define IPAQ_ASIC3_SD_CTRL_MemCardXferDataLen(_b) IPAQ_ASIC3_SD( _b, u16, MemCardXferDataLen ) /* */
+#define IPAQ_ASIC3_SD_CTRL_MemCardOptionSetup(_b) IPAQ_ASIC3_SD( _b, u16, MemCardOptionSetup ) /* */
+#define IPAQ_ASIC3_SD_CTRL_ErrorStatus0(_b) IPAQ_ASIC3_SD( _b, u16, ErrorStatus0 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_ErrorStatus1(_b) IPAQ_ASIC3_SD( _b, u16, ErrorStatus1 ) /* */
+#define IPAQ_ASIC3_SD_CTRL_DataPort(_b) IPAQ_ASIC3_SD( _b, u16, DataPort ) /* */
+#define IPAQ_ASIC3_SD_CTRL_TransactionCtrl(_b) IPAQ_ASIC3_SD( _b, u16, TransactionCtrl ) /* */
+#define IPAQ_ASIC3_SD_CTRL_SoftwareReset(_b) IPAQ_ASIC3_SD( _b, u16, SoftwareReset ) /* */
+
+#define SD_CTRL_SOFTWARE_RESET_CLEAR (1<<0)
+
+#define SD_CTRL_TRANSACTIONCONTROL_SET (1<<8) // 0x0100
+
+#define SD_CTRL_CARDCLOCKCONTROL_FOR_SD_CARD (1<<15)// 0x8000
+#define SD_CTRL_CARDCLOCKCONTROL_ENABLE_CLOCK (1<<8) // 0x0100
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_512 (1<<7) // 0x0080
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_256 (1<<6) // 0x0040
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_128 (1<<5) // 0x0020
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_64 (1<<4) // 0x0010
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_32 (1<<3) // 0x0008
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_16 (1<<2) // 0x0004
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_8 (1<<1) // 0x0002
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_4 (1<<0) // 0x0001
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_2 (0<<0) // 0x0000
+
+#define MEM_CARD_OPTION_REQUIRED 0x000e
+#define MEM_CARD_OPTION_DATA_RESPONSE_TIMEOUT(x) (((x)&0x0f)<<4) /* Four bits */
+#define MEM_CARD_OPTION_C2_MODULE_NOT_PRESENT (1<<14) // 0x4000
+#define MEM_CARD_OPTION_DATA_XFR_WIDTH_1 (1<<15) // 0x8000
+#define MEM_CARD_OPTION_DATA_XFR_WIDTH_4 (0<<15) //~0x8000
+
+#define SD_CTRL_COMMAND_INDEX(x) ((x)&0x3f) /* 0=CMD0, 1=CMD1, ..., 63=CMD63 */
+#define SD_CTRL_COMMAND_TYPE_CMD (0 << 6)
+#define SD_CTRL_COMMAND_TYPE_ACMD (1 << 6)
+#define SD_CTRL_COMMAND_TYPE_AUTHENTICATION (2 << 6)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_NORMAL (0 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1 (4 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1B (5 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R2 (6 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R3 (7 << 8)
+#define SD_CTRL_COMMAND_DATA_PRESENT (1 << 11)
+#define SD_CTRL_COMMAND_TRANSFER_READ (1 << 12)
+#define SD_CTRL_COMMAND_TRANSFER_WRITE (0 << 12)
+#define SD_CTRL_COMMAND_MULTI_BLOCK (1 << 13)
+#define SD_CTRL_COMMAND_SECURITY_CMD (1 << 14)
+
+#define SD_CTRL_STOP_INTERNAL_ISSSUE_CMD12 (1 << 0)
+#define SD_CTRL_STOP_INTERNAL_AUTO_ISSUE_CMD12 (1 << 8)
+
+#define SD_CTRL_CARDSTATUS_RESPONSE_END (1 << 0)
+#define SD_CTRL_CARDSTATUS_RW_END (1 << 2)
+#define SD_CTRL_CARDSTATUS_CARD_REMOVED_0 (1 << 3)
+#define SD_CTRL_CARDSTATUS_CARD_INSERTED_0 (1 << 4)
+#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_0 (1 << 5)
+#define SD_CTRL_CARDSTATUS_WRITE_PROTECT (1 << 7)
+#define SD_CTRL_CARDSTATUS_CARD_REMOVED_3 (1 << 8)
+#define SD_CTRL_CARDSTATUS_CARD_INSERTED_3 (1 << 9)
+#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_3 (1 << 10)
+
+#define SD_CTRL_BUFFERSTATUS_CMD_INDEX_ERROR (1 << 0) // 0x0001
+#define SD_CTRL_BUFFERSTATUS_CRC_ERROR (1 << 1) // 0x0002
+#define SD_CTRL_BUFFERSTATUS_STOP_BIT_END_ERROR (1 << 2) // 0x0004
+#define SD_CTRL_BUFFERSTATUS_DATA_TIMEOUT (1 << 3) // 0x0008
+#define SD_CTRL_BUFFERSTATUS_BUFFER_OVERFLOW (1 << 4) // 0x0010
+#define SD_CTRL_BUFFERSTATUS_BUFFER_UNDERFLOW (1 << 5) // 0x0020
+#define SD_CTRL_BUFFERSTATUS_CMD_TIMEOUT (1 << 6) // 0x0040
+#define SD_CTRL_BUFFERSTATUS_UNK7 (1 << 7) // 0x0080
+#define SD_CTRL_BUFFERSTATUS_BUFFER_READ_ENABLE (1 << 8) // 0x0100
+#define SD_CTRL_BUFFERSTATUS_BUFFER_WRITE_ENABLE (1 << 9) // 0x0200
+#define SD_CTRL_BUFFERSTATUS_ILLEGAL_FUNCTION (1 << 13)// 0x2000
+#define SD_CTRL_BUFFERSTATUS_CMD_BUSY (1 << 14)// 0x4000
+#define SD_CTRL_BUFFERSTATUS_ILLEGAL_ACCESS (1 << 15)// 0x8000
+
+#define SD_CTRL_INTMASKCARD_RESPONSE_END (1 << 0) // 0x0001
+#define SD_CTRL_INTMASKCARD_RW_END (1 << 2) // 0x0004
+#define SD_CTRL_INTMASKCARD_CARD_REMOVED_0 (1 << 3) // 0x0008
+#define SD_CTRL_INTMASKCARD_CARD_INSERTED_0 (1 << 4) // 0x0010
+#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_0 (1 << 5) // 0x0020
+#define SD_CTRL_INTMASKCARD_UNK6 (1 << 6) // 0x0040
+#define SD_CTRL_INTMASKCARD_WRITE_PROTECT (1 << 7) // 0x0080
+#define SD_CTRL_INTMASKCARD_CARD_REMOVED_3 (1 << 8) // 0x0100
+#define SD_CTRL_INTMASKCARD_CARD_INSERTED_3 (1 << 9) // 0x0200
+#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_3 (1 << 10)// 0x0400
+
+#define SD_CTRL_INTMASKBUFFER_CMD_INDEX_ERROR (1 << 0) // 0x0001
+#define SD_CTRL_INTMASKBUFFER_CRC_ERROR (1 << 1) // 0x0002
+#define SD_CTRL_INTMASKBUFFER_STOP_BIT_END_ERROR (1 << 2) // 0x0004
+#define SD_CTRL_INTMASKBUFFER_DATA_TIMEOUT (1 << 3) // 0x0008
+#define SD_CTRL_INTMASKBUFFER_BUFFER_OVERFLOW (1 << 4) // 0x0010
+#define SD_CTRL_INTMASKBUFFER_BUFFER_UNDERFLOW (1 << 5) // 0x0020
+#define SD_CTRL_INTMASKBUFFER_CMD_TIMEOUT (1 << 6) // 0x0040
+#define SD_CTRL_INTMASKBUFFER_UNK7 (1 << 7) // 0x0080
+#define SD_CTRL_INTMASKBUFFER_BUFFER_READ_ENABLE (1 << 8) // 0x0100
+#define SD_CTRL_INTMASKBUFFER_BUFFER_WRITE_ENABLE (1 << 9) // 0x0200
+#define SD_CTRL_INTMASKBUFFER_ILLEGAL_FUNCTION (1 << 13)// 0x2000
+#define SD_CTRL_INTMASKBUFFER_CMD_BUSY (1 << 14)// 0x4000
+#define SD_CTRL_INTMASKBUFFER_ILLEGAL_ACCESS (1 << 15)// 0x8000
+
+#define SD_CTRL_DETAIL0_RESPONSE_CMD_ERROR (1 << 0) // 0x0001
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 2) // 0x0004
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_CMD12 (1 << 3) // 0x0008
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_READ_DATA (1 << 4) // 0x0010
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_WRITE_CRC_STATUS (1 << 5) // 0x0020
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 8) // 0x0100
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_CMD12 (1 << 9) // 0x0200
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_READ_DATA (1 << 10)// 0x0400
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_WRITE_CMD (1 << 11)// 0x0800
+
+#define SD_CTRL_DETAIL1_NO_CMD_RESPONSE (1 << 0) // 0x0001
+#define SD_CTRL_DETAIL1_TIMEOUT_READ_DATA (1 << 4) // 0x0010
+#define SD_CTRL_DETAIL1_TIMEOUT_CRS_STATUS (1 << 5) // 0x0020
+#define SD_CTRL_DETAIL1_TIMEOUT_CRC_BUSY (1 << 6) // 0x0040
+
+#define _IPAQ_ASIC3_SDIO_CTRL_Base 0x1200
+
+#define IPAQ_ASIC3_SDIO(_b, s,x) \
+ (*((volatile s *) ((_b) + _IPAQ_ASIC3_SDIO_CTRL_Base + (_IPAQ_ASIC3_SDIO_CTRL_ ## x))))
+
+#define _IPAQ_ASIC3_SDIO_CTRL_Cmd 0x00
+#define _IPAQ_ASIC3_SDIO_CTRL_CardPortSel 0x04
+#define _IPAQ_ASIC3_SDIO_CTRL_Arg0 0x08
+#define _IPAQ_ASIC3_SDIO_CTRL_Arg1 0x0C
+#define _IPAQ_ASIC3_SDIO_CTRL_TransferBlockCount 0x14
+#define _IPAQ_ASIC3_SDIO_CTRL_Response0 0x18
+#define _IPAQ_ASIC3_SDIO_CTRL_Response1 0x1C
+#define _IPAQ_ASIC3_SDIO_CTRL_Response2 0x20
+#define _IPAQ_ASIC3_SDIO_CTRL_Response3 0x24
+#define _IPAQ_ASIC3_SDIO_CTRL_Response4 0x28
+#define _IPAQ_ASIC3_SDIO_CTRL_Response5 0x2C
+#define _IPAQ_ASIC3_SDIO_CTRL_Response6 0x30
+#define _IPAQ_ASIC3_SDIO_CTRL_Response7 0x34
+#define _IPAQ_ASIC3_SDIO_CTRL_CardStatus 0x38
+#define _IPAQ_ASIC3_SDIO_CTRL_BufferCtrl 0x3C
+#define _IPAQ_ASIC3_SDIO_CTRL_IntMaskCard 0x40
+#define _IPAQ_ASIC3_SDIO_CTRL_IntMaskBuffer 0x44
+#define _IPAQ_ASIC3_SDIO_CTRL_CardXferDataLen 0x4C
+#define _IPAQ_ASIC3_SDIO_CTRL_CardOptionSetup 0x50
+#define _IPAQ_ASIC3_SDIO_CTRL_ErrorStatus0 0x54
+#define _IPAQ_ASIC3_SDIO_CTRL_ErrorStatus1 0x58
+#define _IPAQ_ASIC3_SDIO_CTRL_DataPort 0x60
+#define _IPAQ_ASIC3_SDIO_CTRL_TransactionCtrl 0x68
+#define _IPAQ_ASIC3_SDIO_CTRL_CardIntCtrl 0x6C
+#define _IPAQ_ASIC3_SDIO_CTRL_ClocknWaitCtrl 0x70
+#define _IPAQ_ASIC3_SDIO_CTRL_HostInformation 0x74
+#define _IPAQ_ASIC3_SDIO_CTRL_ErrorCtrl 0x78
+#define _IPAQ_ASIC3_SDIO_CTRL_LEDCtrl 0x7C
+#define _IPAQ_ASIC3_SDIO_CTRL_SoftwareReset 0x1C0
+
+#define IPAQ_ASIC3_SDIO_CTRL_Cmd(_b) IPAQ_ASIC3_SDIO( _b, u16, Cmd ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_CardPortSel(_b) IPAQ_ASIC3_SDIO( _b, u16, CardPortSel ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Arg0(_b) IPAQ_ASIC3_SDIO( _b, u16, Arg0 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Arg1(_b) IPAQ_ASIC3_SDIO( _b, u16, Arg1 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_TransferBlockCount(_b) IPAQ_ASIC3_SDIO( _b, u16, TransferBlockCount ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response0(_b) IPAQ_ASIC3_SDIO( _b, u16, Response0 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response1(_b) IPAQ_ASIC3_SDIO( _b, u16, Response1 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response2(_b) IPAQ_ASIC3_SDIO( _b, u16, Response2 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response3(_b) IPAQ_ASIC3_SDIO( _b, u16, Response3 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response4(_b) IPAQ_ASIC3_SDIO( _b, u16, Response4 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response5(_b) IPAQ_ASIC3_SDIO( _b, u16, Response5 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response6(_b) IPAQ_ASIC3_SDIO( _b, u16, Response6 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_Response7(_b) IPAQ_ASIC3_SDIO( _b, u16, Response7 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_CardStatus(_b) IPAQ_ASIC3_SDIO( _b, u16, CardStatus ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_BufferCtrl(_b) IPAQ_ASIC3_SDIO( _b, u16, BufferCtrl ) /* and error status*/
+#define IPAQ_ASIC3_SDIO_CTRL_IntMaskCard(_b) IPAQ_ASIC3_SDIO( _b, u16, IntMaskCard ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_IntMaskBuffer(_b) IPAQ_ASIC3_SDIO( _b, u16, IntMaskBuffer ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_CardXferDataLen(_b) IPAQ_ASIC3_SDIO( _b, u16, CardXferDataLen ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_CardOptionSetup(_b) IPAQ_ASIC3_SDIO( _b, u16, CardOptionSetup ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_ErrorStatus0(_b) IPAQ_ASIC3_SDIO( _b, u16, ErrorStatus0 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_ErrorStatus1(_b) IPAQ_ASIC3_SDIO( _b, u16, ErrorStatus1 ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_DataPort(_b) IPAQ_ASIC3_SDIO( _b, u16, DataPort ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_TransactionCtrl(_b) IPAQ_ASIC3_SDIO( _b, u16, TransactionCtrl ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_CardIntCtrl(_b) IPAQ_ASIC3_SDIO( _b, u16, CardIntCtrl ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_ClocknWaitCtrl(_b) IPAQ_ASIC3_SDIO( _b, u16, ClocknWaitCtrl ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_HostInformation(_b) IPAQ_ASIC3_SDIO( _b, u16, HostInformation ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_ErrorCtrl(_b) IPAQ_ASIC3_SDIO( _b, u16, ErrorCtrl ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_LEDCtrl(_b) IPAQ_ASIC3_SDIO( _b, u16, LEDCtrl ) /* */
+#define IPAQ_ASIC3_SDIO_CTRL_SoftwareReset(_b) IPAQ_ASIC3_SDIO( _b, u16, SoftwareReset ) /* */
+
+#define IPAQ_ASIC3_MAP_SIZE 0x2000
+
+#endif
--
Best regards,
Paul mailto:[email protected]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
