[PATCH/RFC 2.6.20 2/2] fbdev: Hecuba fb driver

[Jaya Kumar <jayakumar.lkml@gmail.com>]

This patch implements support for the E-Ink/hecuba display device. It uses
deferred IO support.

Thanks,
jaya

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>

---

 hecubafb.c |  480 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 480 insertions(+)

---

diff --git a/drivers/video/hecubafb.c b/drivers/video/hecubafb.c
new file mode 100644
index 0000000..9944bee
--- /dev/null
+++ b/drivers/video/hecubafb.c
@@ -0,0 +1,480 @@
+/*
+ * linux/drivers/video/hecubafb.c -- FB driver for Hecuba controller
+ *
+ * Copyright (C) 2006, Jaya Kumar 
+ * This work was sponsored by CIS(M) Sdn Bhd
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven.
+ * This work was possible because of apollo display code from E-Ink's website
+ * http://support.eink.com/community
+ * All information used to write this code is from public material made
+ * available by E-Ink on its support site. Some commands such as 0xA4
+ * were found by looping through cmd=0x00 thru 0xFF and supplying random
+ * values. There are other commands that the display is capable of,
+ * beyond the 5 used here but they are more complex. 
+ *
+ * This driver is written to be used with the Hecuba display controller
+ * board, and tested with the EInk 800x600 display in 1 bit mode. 
+ * The interface between Hecuba and the host is TTL based GPIO. The
+ * GPIO requirements are 8 writable data lines and 6 lines for control.
+ * Only 4 of the controls are actually used here but 6 for future use.
+ * The driver requires the IO addresses for data and control GPIO at 
+ * load time. It is also possible to use this display with a standard 
+ * PC parallel port. 
+ *
+ * General notes:
+ * - User must set hecubafb_enable=1 to enable it
+ * - User must set dio_addr=0xIOADDR cio_addr=0xIOADDR c2io_addr=0xIOADDR
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/list.h>
+#include <asm/uaccess.h>
+
+/* Apollo controller specific defines */
+#define APOLLO_START_NEW_IMG	0xA0
+#define APOLLO_STOP_IMG_DATA	0xA1
+#define APOLLO_DISPLAY_IMG	0xA2
+#define APOLLO_ERASE_DISPLAY	0xA3
+#define APOLLO_INIT_DISPLAY	0xA4
+
+/* Hecuba interface specific defines */
+/* WUP is inverted, CD is inverted, DS is inverted */
+#define HCB_NWUP_BIT	0x01
+#define HCB_NDS_BIT 	0x02
+#define HCB_RW_BIT 	0x04
+#define HCB_NCD_BIT 	0x08
+#define HCB_ACK_BIT 	0x80
+
+/* Display specific information */
+#define DPY_W 600
+#define DPY_H 800
+
+struct hecubafb_par {
+	unsigned long dio_addr;
+	unsigned long cio_addr;
+	unsigned long c2io_addr;
+	unsigned char ctl;
+	struct fb_info *info;
+	unsigned int irq;
+};
+
+static struct fb_fix_screeninfo hecubafb_fix __initdata = {
+	.id =		"hecubafb",
+	.type =		FB_TYPE_PACKED_PIXELS,
+	.visual =	FB_VISUAL_MONO01,
+	.xpanstep =	0,
+	.ypanstep =	0,
+	.ywrapstep =	0,
+	.accel =	FB_ACCEL_NONE,
+};
+
+static struct fb_var_screeninfo hecubafb_var __initdata = {
+	.xres		= DPY_W,
+	.yres		= DPY_H,
+	.xres_virtual	= DPY_W,
+	.yres_virtual	= DPY_H,
+	.bits_per_pixel	= 1,
+	.nonstd		= 1,
+};
+
+static unsigned long dio_addr;
+static unsigned long cio_addr;
+static unsigned long c2io_addr;
+static unsigned long splashval;
+static unsigned int nosplash;
+static unsigned int hecubafb_enable;
+static unsigned int irq;
+
+static DECLARE_WAIT_QUEUE_HEAD(hecubafb_waitq);
+
+static void hcb_set_ctl(struct hecubafb_par *par)
+{
+	outb(par->ctl, par->cio_addr);
+}
+
+static unsigned char hcb_get_ctl(struct hecubafb_par *par)
+{
+	return inb(par->c2io_addr);
+}
+
+static void hcb_set_data(struct hecubafb_par *par, unsigned char value)
+{
+	outb(value, par->dio_addr);
+}
+
+static int __devinit apollo_init_control(struct hecubafb_par *par)
+{
+	unsigned char ctl;
+	/* for init, we want the following setup to be set:
+	WUP = lo
+	ACK = hi
+	DS = hi
+	RW = hi
+	CD = lo 
+	*/
+
+	/* write WUP to lo, DS to hi, RW to hi, CD to lo */
+	par->ctl = HCB_NWUP_BIT | HCB_RW_BIT | HCB_NCD_BIT ;
+	par->ctl &= ~HCB_NDS_BIT;
+	hcb_set_ctl(par);
+
+	/* check ACK is not lo */
+	ctl = hcb_get_ctl(par);
+	if ((ctl & HCB_ACK_BIT)) {
+		printk(KERN_ERR "Fail because ACK is already low\n");
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+void hcb_wait_for_ack(struct hecubafb_par *par)
+{
+
+	int timeout;
+	unsigned char ctl;
+
+	timeout=500;
+	do {
+		ctl = hcb_get_ctl(par);
+		if ((ctl & HCB_ACK_BIT)) 
+			return;
+		udelay(1);
+	} while (timeout--);
+	printk(KERN_ERR "timed out waiting for ack\n");
+}
+
+void hcb_wait_for_ack_clear(struct hecubafb_par *par)
+{
+
+	int timeout;
+	unsigned char ctl;
+
+	timeout=500;
+	do {
+		ctl = hcb_get_ctl(par);
+		if (!(ctl & HCB_ACK_BIT)) 
+			return;
+		udelay(1);
+	} while (timeout--);
+	printk(KERN_ERR "timed out waiting for clear\n");
+}
+
+void apollo_send_data(struct hecubafb_par *par, unsigned char data)
+{
+	/* set data */
+	hcb_set_data(par, data);
+
+	/* set DS low */
+	par->ctl |= HCB_NDS_BIT;
+	hcb_set_ctl(par);
+
+	hcb_wait_for_ack(par);
+
+	/* set DS hi */
+	par->ctl &= ~(HCB_NDS_BIT);
+	hcb_set_ctl(par);
+	
+	hcb_wait_for_ack_clear(par);
+}
+
+void apollo_send_command(struct hecubafb_par *par, unsigned char data)
+{
+	/* command so set CD to high */
+	par->ctl &= ~(HCB_NCD_BIT);
+	hcb_set_ctl(par);
+
+	/* actually strobe with command */
+	apollo_send_data(par, data);
+
+	/* clear CD back to low */
+	par->ctl |= (HCB_NCD_BIT);
+	hcb_set_ctl(par);
+}
+
+/* main hecubafb functions */
+
+static void hecubafb_dpy_update(struct hecubafb_par *par)
+{
+	int i;
+	unsigned char *buf = par->info->screen_base;
+
+	apollo_send_command(par, 0xA0);
+
+	for (i=0; i < (DPY_W*DPY_H/8); i++) {
+		apollo_send_data(par, *(buf++));
+	}
+
+	apollo_send_command(par, 0xA1);
+	apollo_send_command(par, 0xA2);
+}
+
+/* this is called back from the deferred io workqueue */
+static void hecubafb_dpy_deferred_io(struct fb_info *info, 
+				struct list_head *pagelist)
+{
+	hecubafb_dpy_update(info->par);
+}
+
+static void hecubafb_fillrect(struct fb_info *info,
+				   const struct fb_fillrect *rect)
+{
+	struct hecubafb_par *par = info->par;
+
+	cfb_fillrect(info, rect);
+
+	hecubafb_dpy_update(par);
+}
+
+static void hecubafb_copyarea(struct fb_info *info,
+				   const struct fb_copyarea *area)
+{
+	struct hecubafb_par *par = info->par;
+
+	cfb_copyarea(info, area);
+
+	hecubafb_dpy_update(par);
+}
+
+static void hecubafb_imageblit(struct fb_info *info, 
+				const struct fb_image *image)
+{
+	struct hecubafb_par *par = info->par;
+
+	cfb_imageblit(info, image);
+
+	hecubafb_dpy_update(par);
+}
+
+/*
+ * this is the slow path from userspace. they can seek and write to
+ * the fb. it's inefficient to do anything less than a full screen draw 
+ */
+static ssize_t hecubafb_write(struct file *file, const char __user *buf, 
+				size_t count, loff_t *ppos)
+{
+	struct inode *inode;
+	int fbidx;
+	struct fb_info *info;
+	unsigned long p;
+	int err=-EINVAL;
+	struct hecubafb_par *par;
+	unsigned int xres;
+	unsigned int fbmemlength;
+
+	p = *ppos;
+	inode = file->f_dentry->d_inode;
+	fbidx = iminor(inode);
+	info = registered_fb[fbidx];
+
+	if (!info || !info->screen_base)
+		return -ENODEV;
+
+	par = info->par;
+	xres = info->var.xres;
+	fbmemlength = (xres * info->var.yres)/8;
+
+	if (p > fbmemlength)
+		return -ENOSPC;
+
+	err = 0;
+	if ((count + p) > fbmemlength) {
+		count = fbmemlength - p;
+		err = -ENOSPC;
+	}
+
+	if (count) {
+		char *base_addr;
+
+		base_addr = info->screen_base;
+		count -= copy_from_user(base_addr + p, buf, count);
+		*ppos += count;
+		err = -EFAULT;
+	}
+
+	hecubafb_dpy_update(par);
+
+	if (count)
+		return count;
+
+	return err;
+}
+
+static struct fb_ops hecubafb_ops = {
+	.owner		= THIS_MODULE,
+	.fb_write	= hecubafb_write,
+	.fb_fillrect	= hecubafb_fillrect,
+	.fb_copyarea	= hecubafb_copyarea,
+	.fb_imageblit	= hecubafb_imageblit,
+};
+
+static struct fb_deferred_io hecubafb_defio = {
+	.delay		= HZ,
+	.deferred_io	= hecubafb_dpy_deferred_io,
+};
+
+static int __devinit hecubafb_probe(struct platform_device *dev)
+{
+	struct fb_info *info;
+	int retval = -ENOMEM;
+	int videomemorysize;
+	unsigned char *videomemory;
+	struct hecubafb_par *par;
+
+	videomemorysize = (DPY_W*DPY_H)/8;
+
+	if (!(videomemory = vmalloc(videomemorysize)))
+		return retval;
+
+	memset(videomemory, 0, videomemorysize);
+
+	info = framebuffer_alloc(sizeof(struct hecubafb_par), &dev->dev);
+	if (!info)
+		goto err;
+
+	info->screen_base = (char __iomem *) videomemory;
+	info->fbops = &hecubafb_ops;
+
+	info->var = hecubafb_var;
+	info->fix = hecubafb_fix;
+	info->fix.smem_len = videomemorysize;
+	par = info->par;
+	par->info = info;
+
+	if (!dio_addr || !cio_addr || !c2io_addr) {
+		printk(KERN_WARNING "no IO addresses supplied\n");
+		goto err1;
+	}
+	par->dio_addr = dio_addr;
+	par->cio_addr = cio_addr;
+	par->c2io_addr = c2io_addr;
+	info->flags = FBINFO_FLAG_DEFAULT;
+
+	info->fbdefio = &hecubafb_defio;
+	fb_deferred_io_init(info);
+
+	retval = register_framebuffer(info);
+	if (retval < 0)
+		goto err1;
+	platform_set_drvdata(dev, info);
+
+	printk(KERN_INFO
+	       "fb%d: Hecuba frame buffer device, using %dK of video memory\n",
+	       info->node, videomemorysize >> 10);
+
+	/* this inits the dpy */
+	apollo_init_control(par);
+
+	apollo_send_command(par, APOLLO_INIT_DISPLAY);
+	apollo_send_data(par, 0x81);
+
+	/* have to wait while display resets */
+	udelay(1000);
+
+	/* if we were told to splash the screen, we just clear it */
+	if (!nosplash) {
+		apollo_send_command(par, APOLLO_ERASE_DISPLAY);
+		apollo_send_data(par, splashval);
+	}
+
+	return 0;
+err1:
+	framebuffer_release(info);
+err:
+	vfree(videomemory);
+	return retval;
+}
+
+static int __devexit hecubafb_remove(struct platform_device *dev)
+{
+	struct fb_info *info = platform_get_drvdata(dev);
+
+	if (info) {
+		fb_deferred_io_cleanup(info);
+		unregister_framebuffer(info);
+		vfree(info->screen_base);
+		framebuffer_release(info);
+	}
+	return 0;
+}
+
+static struct platform_driver hecubafb_driver = {
+	.probe	= hecubafb_probe,
+	.remove = hecubafb_remove,
+	.driver	= {
+		.name	= "hecubafb",
+	},
+};
+
+static struct platform_device *hecubafb_device;
+
+static int __init hecubafb_init(void)
+{
+	int ret;
+
+	if (!hecubafb_enable) {
+		printk(KERN_ERR "Use hecubafb_enable to enable the device\n");
+		return -ENXIO;
+	}
+
+	ret = platform_driver_register(&hecubafb_driver);
+	if (!ret) {
+		hecubafb_device = platform_device_alloc("hecubafb", 0);
+		if (hecubafb_device) 
+			ret = platform_device_add(hecubafb_device);
+		else 
+			ret = -ENOMEM;
+
+		if (ret) {
+			platform_device_put(hecubafb_device);
+			platform_driver_unregister(&hecubafb_driver);
+		}
+	}
+	return ret;
+
+}
+
+static void __exit hecubafb_exit(void)
+{
+	platform_device_unregister(hecubafb_device);
+	platform_driver_unregister(&hecubafb_driver);
+}
+
+module_param(nosplash, uint, 0);
+MODULE_PARM_DESC(nosplash, "Disable doing the splash screen");
+module_param(hecubafb_enable, uint, 0);
+MODULE_PARM_DESC(hecubafb_enable, "Enable communication with Hecuba board");
+module_param(dio_addr, ulong, 0);
+MODULE_PARM_DESC(dio_addr, "IO address for data, eg: 0x480");
+module_param(cio_addr, ulong, 0);
+MODULE_PARM_DESC(cio_addr, "IO address for control, eg: 0x400");
+module_param(c2io_addr, ulong, 0);
+MODULE_PARM_DESC(c2io_addr, "IO address for secondary control, eg: 0x408");
+module_param(splashval, ulong, 0);
+MODULE_PARM_DESC(splashval, "Splash pattern: 0x00 is black, 0x01 is white");
+module_param(irq, uint, 0);
+MODULE_PARM_DESC(irq, "IRQ for the Hecuba board");
+
+module_init(hecubafb_init);
+module_exit(hecubafb_exit);
+
+MODULE_DESCRIPTION("fbdev driver for Hecuba board");
+MODULE_AUTHOR("Jaya Kumar");
+MODULE_LICENSE("GPL");
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/