Re: hwsusp defunct

[Jiri Slaby <jirislaby@gmail.com>]

Cc: linux-acpi
not-cc: linux-pm

Rafael J. Wysocki napsal(a):
> On Tuesday, 6 February 2007 12:18, Jiri Slaby wrote:
> > This is blindly written dmesg after resume. See it whole at [2]:
> > Suspending device 0.0
> > ACPI Exception (exoparg2-0442): AE_AML_PACKAGE_LIMIT, Index (000000007) is beyon
> > d end of object [20070126]
> > ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.GTM_]
> > (Node dfe64fcc), AE_AML_PACKAGE_LIMIT
> > ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN0._
> > GTM] (Node dfe649f0), AE_AML_PACKAGE_LIMIT
> > ...
> > hda: selected mode 0x45
> > ACPI Error (dsopcode-0481): Attempt to CreateField of length zero [20070126]
> > ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA]
> > (Node dfe64ec8), AE_AML_OPERAND_VALUE
> > ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN0.D
> > RV1._GTF] (Node dfe64964), AE_AML_OPERAND_VALUE
> > do_drive_get_GTF: Run _GTF error: status = 0x3006
>
> This looks like an ACPI-vs-IDE problem.  You can try to use libata drivers instead
> of the "old IDE" ones.
>
> > $ ls -l /sys/block/hda/device
> > lrwxrwxrwx 1 root root 0 úno  6 12:14 /sys/block/hda/device -> 
> > ../../devices/pci0000:00/0000:00:1f.1/ide0/0.0
> > $ ls -l /sys/block/hda/device/driver
> > lrwxrwxrwx 1 root root 0 úno  6 12:15 /sys/block/hda/device/driver -> 
> > ../../../../../bus/ide/drivers/ide-disk
> > $ ls -l /sys/block/hda/device/driver/0.0
> > lrwxrwxrwx 1 root root 0 úno  6 12:16 /sys/block/hda/device/driver/0.0 -> 
> > ../../../../devices/pci0000:00/0000:00:1f.1/ide0/0.0
> > # lspci -vvvxxs 0000:00:1f.1
> > 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller 
> > (rev 02) (prog-if 8a [Master SecP PriP])
> >          Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
> >          Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> > Stepping- SERR- FastB2B-
> >          Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> > <TAbort- <MAbort- >SERR- <PERR-
> >          Latency: 0
> >          Interrupt: pin A routed to IRQ 5
> >          Region 0: I/O ports at 01f0 [size=8]
> >          Region 1: I/O ports at 03f4 [size=1]
> >          Region 2: I/O ports at 0170 [size=8]
> >          Region 3: I/O ports at 0374 [size=1]
> >          Region 4: I/O ports at fc00 [size=16]
> >          Region 5: Memory at 30100000 (32-bit, non-prefetchable) [size=1K]
> > 00: 86 80 db 24 07 00 80 02 02 8a 01 01 00 00 00 00
> > 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
> > 20: 01 fc 00 00 00 00 10 30 00 00 00 00 43 10 a6 80
> > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
> >
> > Do you want acpidump?
>
> I'm not an ACPI expert, it won't tell me a lot, but perhaps you should add
> linux-acpi to the Cc list. ;-)
[...]
> [1]
>   http://www.fi.muni.cz/~xslaby/sklad/config-mm
> [2]
>   http://www.fi.muni.cz/~xpapiez/test/dmesg-mm.txt

Ok, acpi folks, any suggests?

thanks,
--
http://www.fi.muni.cz/~xslaby/            Jiri Slaby
faculty of informatics, masaryk university, brno, cz
e-mail: jirislaby gmail com, gpg pubkey fingerprint:
B674 9967 0407 CE62 ACC8  22A0 32CC 55C3 39D4 7A7E
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/