Re: [PATCH] backlight control for Frontpath ProGear HX1050+

[Marcin Juszkiewicz <openembedded@hrw.one.pl>]

Dnia wtorek, 6 lutego 2007 20:26, Richard Purdie napisał:
> On Tue, 2007-02-06 at 14:30 +0100, Marcin Juszkiewicz wrote:

> > Add control of LCD backlight for Frontpath ProGear HX1050+.
> > Patch is based on
> > http://downloads.sf.net/progear/progear-lcd-0.2.tar.gz driver by M
> > Schacht.

> This is very similar to corgi_bl which I have some changes I was
> considering to make it a bit more efficient/clean. The same changes
> could apply to this driver:
> > +static int progearbl_intensity;
> > +static struct backlight_properties progearbl_data;
>
> Not sure you need the above line?

both removed

> > +static struct backlight_device *progear_backlight_device;
>
> You shouldn't need this structure pointer (see below)

removed

> > +static int progearbl_get_intensity(struct backlight_device *bd)
> > +{
> > +       return progearbl_intensity;
> > +}
>
> Can you read PMU_LPCR and return it (minus HW_LEVEL_MIN) here? corgi_bl
> only stores this as it can't read back from the hardware. Either
> approach is probably ok (although if the register can be updated by
> other means, it should be read).

changed to be read from hardware

> > +static int progearbl_set_intensity(struct backlight_device *bd)
> > +{
> > +       progearbl_send_intensity(progear_backlight_device);
> > +       return 0;
> > +}
>
> You can use progearbl_send_intensity(bd); here or maybe lose the
> function all together?

progearbl_set_intensity dropped, progearbl_sent_intensity renamed 
to progearbl_set_intensity

> > +static struct backlight_properties progearbl_data = {
> > +       .owner = THIS_MODULE,
> > +       .get_brightness = progearbl_get_intensity,
> > +       .update_status = progearbl_set_intensity,
>
> progearbl_send_intensity?

done

> > +       pci_read_config_byte(sb_dev, SB_MPS1, &temp);
> > +       pci_write_config_byte(sb_dev, SB_MPS1, temp | 0x20);
> > +
> > +       progear_backlight_device =
> > backlight_device_register("progear-bl", +			   &pdev->dev, NULL,
> > &progearbl_data);
> > +       if (IS_ERR(progear_backlight_device))
> > +               return PTR_ERR(progear_backlight_device);
>
> platform_set_drvdata(pdev, progear_backlight_device);

added

> > +static int progearbl_remove(struct platform_device *dev)
> > +{
> > +       backlight_device_unregister(progear_backlight_device);
>
> struct backlight_device *bd = platform_get_drvdata(pdev);
> backlight_device_unregister(bd);

changed

Updated version below:

From: Marcin Juszkiewicz <openembedded@hrw.one.pl>

Add control of LCD backlight for Frontpath ProGear HX1050+.
Patch is based on http://downloads.sf.net/progear/progear-lcd-0.2.tar.gz
driver by M Schacht.

Signed-Off-By: Marcin Juszkiewicz <openembedded@hrw.one.pl>

---
Patch follow kernel version 2.6.20

 Kconfig      |    8 +++
 Makefile     |    1 
 progear_bl.c |  154 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 163 insertions(+)

Index: git/drivers/video/backlight/Kconfig
===================================================================
--- git.orig/drivers/video/backlight/Kconfig	2006-12-29 17:31:36.511043439 +0100
+++ git/drivers/video/backlight/Kconfig	2007-02-07 08:57:31.020095845 +0100
@@ -66,3 +66,11 @@
 	  If you have a HP Jornada 680, say y to enable the
 	  backlight driver.
 
+config BACKLIGHT_PROGEAR
+       tristate "Frontpath ProGear Backlight Driver"
+       depends on BACKLIGHT_DEVICE && PCI && X86
+       default y
+       help
+         If you have a Frontpath ProGear say Y to enable the
+         backlight driver.
+
Index: git/drivers/video/backlight/progear_bl.c
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ git/drivers/video/backlight/progear_bl.c	2007-02-07 08:55:46.813993140 +0100
@@ -0,0 +1,154 @@
+/*
+ *  Backlight Driver for Frontpath ProGear HX1050+
+ *
+ *  Copyright (c) 2006 Marcin Juszkiewicz
+ *
+ *  Based on Progear LCD driver by M Schacht
+ *  <mschacht at alumni dot washington dot edu>
+ *
+ *  Based on Sharp's Corgi Backlight Driver
+ *  Based on Backlight Driver for HP Jornada 680
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/fb.h>
+#include <linux/backlight.h>
+#include <linux/pci.h>
+#include <asm/uaccess.h>
+
+#define PMU_LPCR               0xB0
+#define SB_MPS1                0x61
+#define HW_LEVEL_MAX           0x77
+#define HW_LEVEL_MIN           0x4f
+
+static struct pci_dev *pmu_dev = NULL;
+static struct pci_dev *sb_dev = NULL;
+
+static int progearbl_set_intensity(struct backlight_device *bd)
+{
+	int intensity = bd->props->brightness;
+
+	if (bd->props->power != FB_BLANK_UNBLANK)
+		intensity = 0;
+	if (bd->props->fb_blank != FB_BLANK_UNBLANK)
+		intensity = 0;
+
+	pci_write_config_byte(pmu_dev, PMU_LPCR, intensity + HW_LEVEL_MIN);
+
+	return 0;
+}
+
+static int progearbl_get_intensity(struct backlight_device *bd)
+{
+	u8 intensity;
+	pci_read_config_byte(pmu_dev, PMU_LPCR, &intensity);
+
+	return intensity - HW_LEVEL_MIN;
+}
+
+static struct backlight_properties progearbl_data = {
+	.owner = THIS_MODULE,
+	.get_brightness = progearbl_get_intensity,
+	.update_status = progearbl_set_intensity,
+};
+
+static int progearbl_probe(struct platform_device *pdev)
+{
+	u8 temp;
+	struct backlight_device *progear_backlight_device;
+
+	pmu_dev = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, 0);
+	if (!pmu_dev) {
+		printk("ALI M7101 PMU not found.\n");
+		return -ENODEV;
+	}
+
+	sb_dev = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, 0);
+	if (!sb_dev) {
+		printk("ALI 1533 SB not found.\n");
+		pci_dev_put(pmu_dev);
+		return -ENODEV;
+	}
+
+	/*     Set SB_MPS1 to enable brightness control. */
+	pci_read_config_byte(sb_dev, SB_MPS1, &temp);
+	pci_write_config_byte(sb_dev, SB_MPS1, temp | 0x20);
+
+	progear_backlight_device = backlight_device_register("progear-bl",
+							     &pdev->dev, NULL,
+							     &progearbl_data);
+	if (IS_ERR(progear_backlight_device))
+		return PTR_ERR(progear_backlight_device);
+
+	platform_set_drvdata(pdev, progear_backlight_device);
+
+	progearbl_data.power = FB_BLANK_UNBLANK;
+	progearbl_data.brightness = HW_LEVEL_MAX - HW_LEVEL_MIN;
+	progearbl_data.max_brightness = HW_LEVEL_MAX - HW_LEVEL_MIN;
+	progearbl_set_intensity(progear_backlight_device);
+
+	return 0;
+}
+
+static int progearbl_remove(struct platform_device *pdev)
+{
+	struct backlight_device *bd = platform_get_drvdata(pdev);
+	backlight_device_unregister(bd);
+
+	return 0;
+}
+
+static struct platform_driver progearbl_driver = {
+	.probe = progearbl_probe,
+	.remove = progearbl_remove,
+	.driver = {
+		   .name = "progear-bl",
+		   },
+};
+
+static struct platform_device *progearbl_device;
+
+static int __init progearbl_init(void)
+{
+	int ret = platform_driver_register(&progearbl_driver);
+
+	if (!ret) {
+		progearbl_device = platform_device_alloc("progear-bl", -1);
+		if (!progearbl_device)
+			return -ENOMEM;
+
+		ret = platform_device_add(progearbl_device);
+
+		if (ret) {
+			platform_device_put(progearbl_device);
+			platform_driver_unregister(&progearbl_driver);
+		}
+	}
+
+	return ret;
+}
+
+static void __exit progearbl_exit(void)
+{
+	pci_dev_put(pmu_dev);
+	pci_dev_put(sb_dev);
+
+	platform_device_unregister(progearbl_device);
+	platform_driver_unregister(&progearbl_driver);
+}
+
+module_init(progearbl_init);
+module_exit(progearbl_exit);
+
+MODULE_AUTHOR("Marcin Juszkiewicz <linux@hrw.one.pl>");
+MODULE_DESCRIPTION("ProGear Backlight Driver");
+MODULE_LICENSE("GPL");
Index: git/drivers/video/backlight/Makefile
===================================================================
--- git.orig/drivers/video/backlight/Makefile	2006-12-29 17:31:36.511043439 +0100
+++ git/drivers/video/backlight/Makefile	2007-02-06 21:34:54.503712923 +0100
@@ -5,3 +5,4 @@
 obj-$(CONFIG_BACKLIGHT_CORGI)	+= corgi_bl.o
 obj-$(CONFIG_BACKLIGHT_HP680)	+= hp680_bl.o
 obj-$(CONFIG_BACKLIGHT_LOCOMO)	+= locomolcd.o
+obj-$(CONFIG_BACKLIGHT_PROGEAR) += progear_bl.o

-- 
JID: hrw-jabber.org
OpenEmbedded developer/consultant

 Don't mind me, I'm just checking if you are dense enough to cause a tide


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/