[PATCH 07/12] md: move raid5 parity checks to raid5_run_ops

[Dan Williams <dan.j.williams@intel.com>]

From: Dan Williams <dan.j.williams@intel.com>

handle_stripe sets STRIPE_OP_CHECK to request a check operation in
raid5_run_ops.  If raid5_run_ops is able to perform the check with a
dma engine the parity will be preserved in memory removing the need to
re-read it from disk, as is necessary in the synchronous case.

'Repair' operations re-use the same logic as compute block, with the caveat
that the results of the compute block are immediately written back to the
parity disk.  To differentiate these operations the STRIPE_OP_MOD_REPAIR_PD
flag is added.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---

 drivers/md/raid5.c |   81 ++++++++++++++++++++++++++++++++++++++++------------
 1 files changed, 62 insertions(+), 19 deletions(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 279a30c..2422253 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -2411,32 +2411,75 @@ static void handle_stripe5(struct stripe_head *sh)
 			locked += handle_write_operations5(sh, rcw, 0);
 	}
 
-	/* maybe we need to check and possibly fix the parity for this stripe
-	 * Any reads will already have been scheduled, so we just see if enough data
-	 * is available
+	/* 1/ Maybe we need to check and possibly fix the parity for this stripe.
+	 *    Any reads will already have been scheduled, so we just see if enough data
+	 *    is available.
+	 * 2/ Hold off parity checks while parity dependent operations are in flight
+	 *    (conflicting writes are protected by the 'locked' variable)
 	 */
-	if (syncing && locked == 0 &&
-	    !test_bit(STRIPE_INSYNC, &sh->state)) {
+	if ((syncing && locked == 0 && !test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending) &&
+		!test_bit(STRIPE_INSYNC, &sh->state)) ||
+	    	test_bit(STRIPE_OP_CHECK, &sh->ops.pending) ||
+	    	test_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending)) {
+
 		set_bit(STRIPE_HANDLE, &sh->state);
-		if (failed == 0) {
-			BUG_ON(uptodate != disks);
-			compute_parity5(sh, CHECK_PARITY);
-			uptodate--;
-			if (page_is_zero(sh->dev[sh->pd_idx].page)) {
-				/* parity is correct (on disc, not in buffer any more) */
-				set_bit(STRIPE_INSYNC, &sh->state);
-			} else {
-				conf->mddev->resync_mismatches += STRIPE_SECTORS;
-				if (test_bit(MD_RECOVERY_CHECK, &conf->mddev->recovery))
-					/* don't try to repair!! */
+		/* Take one of the following actions:
+		 * 1/ start a check parity operation if (uptodate == disks)
+		 * 2/ finish a check parity operation and act on the result
+		 * 3/ skip to the writeback section if we previously
+		 *    initiated a recovery operation
+		 */
+		if (failed == 0 && !test_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending)) {
+			if (!test_and_set_bit(STRIPE_OP_CHECK, &sh->ops.pending)) {
+				BUG_ON(uptodate != disks);
+				clear_bit(R5_UPTODATE, &sh->dev[sh->pd_idx].flags);
+				sh->ops.count++;
+				uptodate--;
+			} else if (test_and_clear_bit(STRIPE_OP_CHECK, &sh->ops.complete)) {
+				clear_bit(STRIPE_OP_CHECK, &sh->ops.ack);
+				clear_bit(STRIPE_OP_CHECK, &sh->ops.pending);
+
+				if (sh->ops.zero_sum_result == 0)
+					/* parity is correct (on disc, not in buffer any more) */
 					set_bit(STRIPE_INSYNC, &sh->state);
 				else {
-					compute_block(sh, sh->pd_idx);
-					uptodate++;
+					conf->mddev->resync_mismatches += STRIPE_SECTORS;
+					if (test_bit(MD_RECOVERY_CHECK, &conf->mddev->recovery))
+						/* don't try to repair!! */
+						set_bit(STRIPE_INSYNC, &sh->state);
+					else {
+						BUG_ON(test_and_set_bit(
+							STRIPE_OP_COMPUTE_BLK,
+							&sh->ops.pending));
+						set_bit(STRIPE_OP_MOD_REPAIR_PD,
+							&sh->ops.pending);
+						BUG_ON(test_and_set_bit(R5_Wantcompute,
+							&sh->dev[sh->pd_idx].flags));
+						sh->ops.target = sh->pd_idx;
+						sh->ops.count++;
+						uptodate++;
+					}
 				}
 			}
 		}
-		if (!test_bit(STRIPE_INSYNC, &sh->state)) {
+
+		/* check if we can clear a parity disk reconstruct */
+		if (test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.complete) &&
+			test_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending)) {
+
+			clear_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending);
+			clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.complete);
+			clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.ack);
+			clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending);
+		}
+
+		/* Wait for check parity and compute block operations to complete
+		 * before write-back
+		 */
+		if (!test_bit(STRIPE_INSYNC, &sh->state) &&
+			!test_bit(STRIPE_OP_CHECK, &sh->ops.pending) &&
+			!test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending)) {
+
 			/* either failed parity check, or recovery is happening */
 			if (failed==0)
 				failed_num = sh->pd_idx;
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/