Re: [PATCH 9/12] repost: cciss: add busy_configuring flag

[Jens Axboe <jens.axboe@oracle.com>]

On Fri, Jan 19 2007, dann frazier wrote:
> On Wed, Dec 13, 2006 at 01:52:36PM +0100, Jens Axboe wrote:
> > On Tue, Dec 12 2006, Mike Miller (OS Dev) wrote:
> > > On Mon, Nov 06, 2006 at 09:32:00PM +0100, Jens Axboe wrote:
> > > > On Mon, Nov 06 2006, Mike Miller (OS Dev) wrote:
> > > > > PATCH 9 of 12
> > > > > 
> > > > > This patch adds a check for busy_configuring to prevent starting a queue
> > > > > on a drive that may be in the midst of updating, configuring, deleting, etc.
> > > > > 
> > > > > This had a test for if the queue was stopped or plugged but that seemed
> > > > > to cause issues.
> > > > > Please consider this for inclusion.
> > > > > 
> > > > > Thanks,
> > > > > mikem
> > > > > 
> > > > > Signed-off-by: Mike Miller <mike.miller@hp.com>
> > > > > 
> > > > > --------------------------------------------------------------------------------
> > > > > 
> > > > > ---
> > > > > 
> > > > >  drivers/block/cciss.c |    5 ++++-
> > > > >  1 files changed, 4 insertions(+), 1 deletion(-)
> > > > > 
> > > > > diff -puN drivers/block/cciss.c~cciss_busy_conf_for_lx2619-rc4 drivers/block/cciss.c
> > > > > --- linux-2.6/drivers/block/cciss.c~cciss_busy_conf_for_lx2619-rc4	2006-11-06 13:27:53.000000000 -0600
> > > > > +++ linux-2.6-root/drivers/block/cciss.c	2006-11-06 13:27:53.000000000 -0600
> > > > > @@ -1190,8 +1190,11 @@ static void cciss_check_queues(ctlr_info
> > > > >  		/* make sure the disk has been added and the drive is real
> > > > >  		 * because this can be called from the middle of init_one.
> > > > >  		 */
> > > > > -		if (!(h->drv[curr_queue].queue) || !(h->drv[curr_queue].heads))
> > > > > +		if (!(h->drv[curr_queue].queue) ||
> > > > > +		    !(h->drv[curr_queue].heads) ||
> > > > > +		    h->drv[curr_queue].busy_configuring)
> > > > >  			continue;
> > > > > +
> > > > >  		blk_start_queue(h->gendisk[curr_queue]->queue);
> > > > 
> > > > This is racy, because you don't start the queue when you unset
> > > > ->busy_configuring later on. For this to be safe, you need to call
> > > > blk_start_queue() when you set ->busy_configuring to 0.
> > > 
> > > Jens, please see Chase's reply to your concerns:
> > > > busy_configuring - I do not think this is racy.  This
> > > > flag is used only when we are removing/deleting a disk.  In
> > > > this case the queue is cleaned up and the disk is deleted.
> > > > If we are doing that then there is no queue to start later.
> > > > The check of this flag in the interrupt handler is to prevent
> > > > us from trying to start a queue that is in the middle of
> > > > being deleted.  This flag could be called busy_deleting.
> > 
> > Ok, no worries then if it's simply a going away flag. I wonder if it's
> > needed at all, but it certainly doesn't hurt.
> 
> hey Jens,
>   Just a poke since I haven't seen this change go into your block
> tree. Is it still in-plan?

I had it stashed for a 2.6.21 merge, it'll go in by then.

-- 
Jens Axboe

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/