On Fri, 15 Dec 2006 15:45:55 +0059
Jiri Slaby <[email protected]> wrote:
> Andrew Morton wrote:
> > Temporarily at
> >
> > http://userweb.kernel.org/~akpm/2.6.20-rc1-mm1/
> >
> > Will appear later at
> >
> > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc1/2.6.20-rc1-mm1/
>
> The kernel panics at boot in pdc_port_start+0x82 with deref of 0x14:
> http://www.fi.muni.cz/~xslaby/sklad/pdc_oops.png
>
> ATA port is not connected, only 2 SATA disks on my
> # lspci -vvxs 02:01.0
> 02:01.0 Mass storage controller: Promise Technology, Inc. PDC40775 (SATA 300
> TX2plus) (rev 02)
> Subsystem: Promise Technology, Inc. PDC40775 (SATA 300 TX2plus)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 72 (1000ns min, 4500ns max), Cache Line Size: 4 bytes
> Interrupt: pin A routed to IRQ 19
> Region 0: I/O ports at 8000 [size=128]
> Region 2: I/O ports at 8400 [size=256]
> Region 3: Memory at fb025000 (32-bit, non-prefetchable) [size=4K]
> Region 4: Memory at fb000000 (32-bit, non-prefetchable) [size=128K]
> [virtual] Expansion ROM at 50000000 [disabled] [size=32K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: 5a 10 73 3d 07 00 30 02 02 00 80 01 01 48 00 00
> 10: 01 80 00 00 00 00 00 00 01 84 00 00 00 50 02 fb
> 20: 00 00 00 fb 00 00 00 00 00 00 00 00 5a 10 73 3d
> 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 04 12
>
Presumably
void __iomem *mmio = (void __iomem *) ap->ioaddr.scr_addr;
gave us a null pointer.
Something like this:
diff -puN drivers/ata/sata_promise.c~a drivers/ata/sata_promise.c
--- a/drivers/ata/sata_promise.c~a
+++ a/drivers/ata/sata_promise.c
@@ -294,6 +294,10 @@ static int pdc_port_start(struct ata_por
void __iomem *mmio = (void __iomem *) ap->ioaddr.scr_addr;
unsigned int tmp;
+ if (!mmio) {
+ rc = -EDOM;
+ goto out_kfree;
+ }
tmp = readl(mmio + 0x014);
tmp = (tmp & ~3) | 1; /* set bits 1:0 = 0:1 */
writel(tmp, mmio + 0x014);
_
should perhaps let you wobble to a state where you can get us the full
dmesg output, please.
Actually, that should already be possible simply using netconsole.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
