[RFC][PATCH 2/2] x86_64: earlyprintk usb debug device support.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This patch is still a little rough but it gets all of the major pieces
correct.  With a little more work this should become a maintainable
driver.

In particular I believe the ehci debug port code is fairly solid
(with rough edges).  However there are several nasty bits that
need to be resolved before we can push this upstream.  Like
my include of ehci.h  And general early kernel space dependency
problems.

But the code works for me so it should at least be a reasonable starting
point for others looking to make the debug port work in a reasonable fashion.

Signed-off-by: Eric W. Biederman <[email protected]>
---
 arch/x86_64/kernel/early_printk.c |  574 +++++++++++++++++++++++++++++++++++++
 drivers/usb/host/ehci.h           |    8 +
 include/asm-x86_64/fixmap.h       |    1 
 3 files changed, 583 insertions(+), 0 deletions(-)

diff --git a/arch/x86_64/kernel/early_printk.c b/arch/x86_64/kernel/early_printk.c
index d4050a5..cb5182d 100644
--- a/arch/x86_64/kernel/early_printk.c
+++ b/arch/x86_64/kernel/early_printk.c
@@ -3,9 +3,19 @@ #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/string.h>
 #include <linux/screen_info.h>
+#include <linux/usb_ch9.h>
+#include <linux/pci_regs.h>
+#include <linux/pci_ids.h>
+#include <linux/errno.h>
 #include <asm/io.h>
 #include <asm/processor.h>
 #include <asm/fcntl.h>
+#include <asm/pci-direct.h>
+#include <asm/pgtable.h>
+#include <asm/fixmap.h>
+#define EARLY_PRINTK
+#include "../../../drivers/usb/host/ehci.h"
+
 
 /* Simple VGA output */
 
@@ -155,6 +165,558 @@ static struct console early_serial_conso
 	.index =	-1,
 };
 
+
+static struct ehci_caps __iomem *ehci_caps;
+static struct ehci_regs __iomem *ehci_regs;
+static struct ehci_dbg_port __iomem *ehci_debug;
+static unsigned dbgp_endpoint_out;
+
+#define USB_DEBUG_DEVNUM 127
+
+#define DBGP_DATA_TOGGLE	0x8800
+#define DBGP_PID_UPDATE(x, tok) \
+	((((x) ^ DBGP_DATA_TOGGLE) & 0xffff00) | ((tok) & 0xff))
+
+#define DBGP_LEN_UPDATE(x, len) (((x) & ~0x0f) | ((len) & 0x0f))
+/*
+ * USB Packet IDs (PIDs)
+ */
+
+/* token */
+#define USB_PID_OUT		0xe1
+#define USB_PID_IN		0x69
+#define USB_PID_SOF		0xa5
+#define USB_PID_SETUP		0x2d
+/* handshake */
+#define USB_PID_ACK		0xd2
+#define USB_PID_NAK		0x5a
+#define USB_PID_STALL		0x1e
+#define USB_PID_NYET		0x96
+/* data */
+#define USB_PID_DATA0		0xc3
+#define USB_PID_DATA1		0x4b
+#define USB_PID_DATA2		0x87
+#define USB_PID_MDATA		0x0f
+/* Special */
+#define USB_PID_PREAMBLE	0x3c
+#define USB_PID_ERR		0x3c
+#define USB_PID_SPLIT		0x78
+#define USB_PID_PING		0xb4
+#define USB_PID_UNDEF_0		0xf0
+
+#define USB_PID_DATA_TOGGLE	0x88
+#define DBGP_CLAIM (DBGP_OWNER | DBGP_ENABLED | DBGP_INUSE)
+
+#define PCI_CAP_ID_EHCI_DEBUG	0xa
+
+#define HUB_ROOT_RESET_TIME	50	/* times are in msec */
+#define HUB_SHORT_RESET_TIME	10
+#define HUB_LONG_RESET_TIME	200
+#define HUB_RESET_TIMEOUT	500
+
+#define DBGP_MAX_PACKET		8
+
+static int dbgp_wait_until_complete(void)
+{
+	unsigned ctrl;
+	for (;;) {
+		ctrl = readl(&ehci_debug->control);
+		/* Stop when the transaction is finished */
+		if (ctrl & DBGP_DONE)
+			break;
+	}
+	/* Now that we have observed the completed transaction,
+	 * clear the done bit.
+	 */
+	writel(ctrl | DBGP_DONE, &ehci_debug->control);
+	return (ctrl & DBGP_ERROR) ? -DBGP_ERRCODE(ctrl) : DBGP_LEN(ctrl);
+}
+
+static void dbgp_mdelay(int ms)
+{
+	int i;
+	while (ms--) {
+		for (i = 0; i < 1000; i++)
+			outb(0x1, 0x80);
+	}
+}
+
+static void dbgp_breath(void)
+{
+	/* Sleep to give the debug port a chance to breathe */
+}
+
+static int dbgp_wait_until_done(unsigned ctrl)
+{
+	unsigned pids, lpid;
+	int ret;
+
+retry:
+	writel(ctrl | DBGP_GO, &ehci_debug->control);
+	ret = dbgp_wait_until_complete();
+	pids = readl(&ehci_debug->pids);
+	lpid = DBGP_PID_GET(pids);
+
+	if (ret < 0)
+		return ret;
+
+	/* If the port is getting full or it has dropped data
+	 * start pacing ourselves, not necessary but it's friendly.
+	 */
+	if ((lpid == USB_PID_NAK) || (lpid == USB_PID_NYET))
+		dbgp_breath();
+	
+	/* If I get a NACK reissue the transmission */
+	if (lpid == USB_PID_NAK)
+		goto retry;
+
+	return ret;
+}
+
+static void dbgp_set_data(const void *buf, int size)
+{
+	const unsigned char *bytes = buf;
+	unsigned lo, hi;
+	int i;
+	lo = hi = 0;
+	for (i = 0; i < 4 && i < size; i++)
+		lo |= bytes[i] << (8*i);
+	for (; i < 8 && i < size; i++)
+		hi |= bytes[i] << (8*(i - 4));
+	writel(lo, &ehci_debug->data03);
+	writel(hi, &ehci_debug->data47);
+}
+
+static void dbgp_get_data(void *buf, int size)
+{
+	unsigned char *bytes = buf;
+	unsigned lo, hi;
+	int i;
+	lo = readl(&ehci_debug->data03);
+	hi = readl(&ehci_debug->data47);
+	for (i = 0; i < 4 && i < size; i++)
+		bytes[i] = (lo >> (8*i)) & 0xff;
+	for (; i < 8 && i < size; i++)
+		bytes[i] = (hi >> (8*(i - 4))) & 0xff;
+}
+
+static int dbgp_bulk_write(unsigned devnum, unsigned endpoint, const char *bytes, int size)
+{
+	unsigned pids, addr, ctrl;
+	int ret;
+	if (size > DBGP_MAX_PACKET)
+		return -1;
+
+	addr = DBGP_EPADDR(devnum, endpoint);
+
+	pids = readl(&ehci_debug->pids);
+	pids = DBGP_PID_UPDATE(pids, USB_PID_OUT);
+	
+	ctrl = readl(&ehci_debug->control);
+	ctrl = DBGP_LEN_UPDATE(ctrl, size);
+	ctrl |= DBGP_OUT;
+	ctrl |= DBGP_GO;
+
+	dbgp_set_data(bytes, size);
+	writel(addr, &ehci_debug->address);
+	writel(pids, &ehci_debug->pids);
+
+	ret = dbgp_wait_until_done(ctrl);
+	if (ret < 0) {
+		return ret;
+	}
+	return ret;
+}
+
+static int dbgp_bulk_read(unsigned devnum, unsigned endpoint, void *data, int size)
+{
+	unsigned pids, addr, ctrl;
+	int ret;
+
+	if (size > DBGP_MAX_PACKET)
+		return -1;
+
+	addr = DBGP_EPADDR(devnum, endpoint);
+
+	pids = readl(&ehci_debug->pids);
+	pids = DBGP_PID_UPDATE(pids, USB_PID_IN);
+		
+	ctrl = readl(&ehci_debug->control);
+	ctrl = DBGP_LEN_UPDATE(ctrl, size);
+	ctrl &= ~DBGP_OUT;
+	ctrl |= DBGP_GO;
+		
+	writel(addr, &ehci_debug->address);
+	writel(pids, &ehci_debug->pids);
+	ret = dbgp_wait_until_done(ctrl);
+	if (ret < 0)
+		return ret;
+	if (size > ret)
+		size = ret;
+	dbgp_get_data(data, size);
+	return ret;
+}
+
+static int dbgp_control_msg(unsigned devnum, int requesttype, int request, 
+	int value, int index, void *data, int size)
+{
+	unsigned pids, addr, ctrl;
+	struct usb_ctrlrequest req;
+	int read;
+	int ret;
+
+	read = (requesttype & USB_DIR_IN) != 0;
+	if (size > (read?DBGP_MAX_PACKET:0))
+		return -1;
+	
+	/* Compute the control message */
+	req.bRequestType = requesttype;
+	req.bRequest = request;
+	req.wValue = value;
+	req.wIndex = index;
+	req.wLength = size;
+
+	pids = DBGP_PID_SET(USB_PID_DATA0, USB_PID_SETUP);
+	addr = DBGP_EPADDR(devnum, 0);
+
+	ctrl = readl(&ehci_debug->control);
+	ctrl = DBGP_LEN_UPDATE(ctrl, sizeof(req));
+	ctrl |= DBGP_OUT;
+	ctrl |= DBGP_GO;
+
+	/* Send the setup message */
+	dbgp_set_data(&req, sizeof(req));
+	writel(addr, &ehci_debug->address);
+	writel(pids, &ehci_debug->pids);
+	ret = dbgp_wait_until_done(ctrl);
+	if (ret < 0)
+		return ret;
+
+
+	/* Read the result */
+	ret = dbgp_bulk_read(devnum, 0, data, size);
+	return ret;
+}
+
+
+/* Find a PCI capability */
+static __u32 __init find_cap(int num, int slot, int func, int cap) 
+{ 
+	u8 pos;
+	int bytes;
+	if (!(read_pci_config_16(num,slot,func,PCI_STATUS) & PCI_STATUS_CAP_LIST))
+		return 0;
+	pos = read_pci_config_byte(num,slot,func,PCI_CAPABILITY_LIST);
+	for (bytes = 0; bytes < 48 && pos >= 0x40; bytes++) { 
+		u8 id;
+		pos &= ~3; 
+		id = read_pci_config_byte(num,slot,func,pos+PCI_CAP_LIST_ID);
+		if (id == 0xff)
+			break;
+		if (id == cap) 
+			return pos; 
+		pos = read_pci_config_byte(num,slot,func,pos+PCI_CAP_LIST_NEXT); 
+	} 
+	return 0;
+} 
+
+static __u32 __init find_dbgp(int ehci_num, unsigned *rbus, unsigned *rslot, unsigned *rfunc)
+{
+	unsigned bus, slot, func;
+	
+	for (bus = 0; bus < 256; bus++) {
+		for (slot = 0; slot < 32; slot++) {
+			for (func = 0; func < 8; func++) {
+				u32 class;
+				unsigned cap;
+				class = read_pci_config(bus, slot, func, PCI_CLASS_REVISION);
+				if ((class >> 8) != PCI_CLASS_SERIAL_USB_EHCI)
+					continue;
+				cap = find_cap(bus, slot, func, PCI_CAP_ID_EHCI_DEBUG);
+				if (!cap)
+					continue;
+				if (ehci_num-- != 0)
+					continue;
+				*rbus = bus;
+				*rslot = slot;
+				*rfunc = func;
+				return cap;
+			}
+		}
+	}
+	return 0;
+}
+
+static int ehci_reset_port(int port)
+{
+	unsigned portsc;
+	unsigned delay_time, delay;
+
+	/* Reset the usb debug port */
+	portsc = readl(&ehci_regs->port_status[port - 1]);
+	portsc &= ~PORT_PE;
+	portsc |= PORT_RESET;
+	writel(portsc, &ehci_regs->port_status[port - 1]);
+
+	delay = HUB_ROOT_RESET_TIME;
+	for (delay_time = 0; delay_time < HUB_RESET_TIMEOUT;
+	     delay_time += delay) {
+		dbgp_mdelay(delay);
+
+		portsc = readl(&ehci_regs->port_status[port - 1]);
+		if (portsc & PORT_RESET) {
+			/* force reset to complete */
+			writel(portsc & ~(PORT_RWC_BITS | PORT_RESET), 
+				&ehci_regs->port_status[port - 1]);
+			while (portsc & PORT_RESET)
+				portsc = readl(&ehci_regs->port_status[port - 1]);
+		}
+
+		/* Device went away? */
+		if (!(portsc & PORT_CONNECT))
+			return -ENOTCONN;
+
+		/* bomb out completely if something weird happend */
+		if ((portsc & PORT_CSC))
+			return -EINVAL;
+
+		/* If we've finished resetting, then break out of the loop */
+		if (!(portsc & PORT_RESET) && (portsc & PORT_PE))
+			return 0;
+	}
+	return -EBUSY;
+}
+
+static int ehci_wait_for_port(int port)
+{
+	unsigned status;
+	int ret, reps;
+	for (reps = 0; reps >= 0; reps++) {
+		status = readl(&ehci_regs->status);
+		if (status & STS_PCD) {
+			ret = ehci_reset_port(port);
+			if (ret == 0)
+				return 0;
+		}
+	}
+	return -ENOTCONN;
+}
+
+
+#define DBGP_DEBUG 0
+#if DBGP_DEBUG
+void early_printk(const char *fmt, ...);
+# define dbgp_printk early_printk
+#else
+static inline void dbgp_printk(const char *fmt, ...) { }
+#endif
+
+static int ehci_setup(void)
+{
+	unsigned cmd, ctrl, status, portsc, hcs_params, debug_port, n_ports;
+	int ret;
+	int i;
+
+	hcs_params = readl(&ehci_caps->hcs_params);
+	debug_port = HCS_DEBUG_PORT(hcs_params);
+	n_ports    = HCS_N_PORTS(hcs_params);
+
+	dbgp_printk("debug_port: %d\n", debug_port);
+	dbgp_printk("n_ports:    %d\n", n_ports);
+
+	/* Reset the EHCI controller */
+	cmd = readl(&ehci_regs->command);
+	cmd |=CMD_RESET;
+	writel(cmd, &ehci_regs->command);
+	while (cmd & CMD_RESET)
+		cmd = readl(&ehci_regs->command);
+
+	/* Claim ownership, but do not enable yet */
+	ctrl = readl(&ehci_debug->control);
+	ctrl |= DBGP_OWNER;
+	ctrl &= ~(DBGP_ENABLED | DBGP_INUSE);
+	writel(ctrl, &ehci_debug->control);
+
+	/* Start the ehci running */
+	cmd = readl(&ehci_regs->command);
+	cmd &= ~(CMD_LRESET | CMD_IAAD | CMD_PSE | CMD_ASE | CMD_RESET);
+	cmd |= CMD_RUN;
+	writel(cmd, &ehci_regs->command);
+
+	/* Ensure everything is routed to the EHCI */
+	writel(FLAG_CF, &ehci_regs->configured_flag);
+
+	/* Wait until the controller is no longer halted */
+	do {
+		status = readl(&ehci_regs->status);
+	} while (status & STS_HALT);
+
+	/* Wait for a device to show up in the debug port */
+	ret = ehci_wait_for_port(debug_port);
+	if (ret < 0) {
+		dbgp_printk("No device found in debug port\n");
+		return -1;
+	}
+
+	/* Enable the debug port */
+	ctrl = readl(&ehci_debug->control);
+	ctrl |= DBGP_CLAIM;
+	writel(ctrl, &ehci_debug->control);
+	ctrl = readl(&ehci_debug->control);
+	if ((ctrl & DBGP_CLAIM) != DBGP_CLAIM) {
+		dbgp_printk("No device in debug port\n");
+		writel(ctrl & ~DBGP_CLAIM, &ehci_debug->control);
+		return -1;
+
+	}
+
+	/* Completely transfer the debug device to the debug controller */
+	portsc = readl(&ehci_regs->port_status[debug_port - 1]);
+	portsc &= ~PORT_PE;
+	writel(portsc, &ehci_regs->port_status[debug_port - 1]);
+
+	return 0;
+}
+
+static __init void early_dbgp_init(char *s)
+{
+	struct usb_debug_descriptor dbgp_desc;
+	void __iomem *ehci_bar;
+	unsigned ctrl, devnum;
+	unsigned bus, slot, func, cap;
+	unsigned debug_port, bar, offset;
+	unsigned bar_val;
+	unsigned dbgp_num;
+	char *e;
+	int ret;
+
+	if (!early_pci_allowed())
+		return;
+
+	dbgp_num = 0;
+	if (*s) {
+		dbgp_num = simple_strtoul(s, &e, 10);
+	}
+	dbgp_printk("dbgp_num: %d\n", dbgp_num);
+	cap = find_dbgp(dbgp_num, &bus, &slot, &func);
+	if (!cap)
+		return;
+
+	dbgp_printk("Found EHCI debug port\n");
+
+	debug_port = read_pci_config(bus, slot, func, cap);
+	bar = (debug_port >> 29) & 0x7;
+	bar = (bar * 4) + 0xc;
+	offset = (debug_port >> 16) & 0xfff;
+	if (bar != PCI_BASE_ADDRESS_0) {
+		dbgp_printk("only debug ports on bar 1 handled.\n");
+		return;
+	}
+
+	/* FIXME this assumes the bar is a 32bit mmio bar */
+	bar_val = read_pci_config(bus, slot, func, PCI_BASE_ADDRESS_0);
+
+	/* FIXME I don't have the bar size so just guess PAGE_SIZE is more
+	 * than enough.  1K is the biggest I have seen.
+	 */
+	set_fixmap_nocache(FIX_DBGP_BASE, bar_val & PAGE_MASK);
+	ehci_bar = (void __iomem *)__fix_to_virt(FIX_DBGP_BASE);
+	ehci_bar += bar_val & ~PAGE_MASK;
+
+	ehci_caps  = ehci_bar;
+	ehci_regs  = ehci_bar + HC_LENGTH(readl(&ehci_caps->hc_capbase));
+	ehci_debug = ehci_bar + offset;
+
+	ret = ehci_setup();
+	if (ret < 0) {
+		dbgp_printk("ehci_setup failed\n");
+		return;
+	}
+
+	/* Find the debug device and make it device number 127 */
+	for (devnum = 0; devnum <= 127; devnum++) {
+		ret = dbgp_control_msg(devnum,
+			USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+			USB_REQ_GET_DESCRIPTOR, (USB_DT_DEBUG << 8), 0,
+			&dbgp_desc, sizeof(dbgp_desc));
+		if (ret > 0)
+			break;
+	}
+	if (devnum > 127) {
+		dbgp_printk("Could not find attached debug device\n");
+		goto err;
+	}
+	if (ret < 0) {
+		dbgp_printk("Attached device is not a debug device\n");
+		goto err;
+	}
+	dbgp_endpoint_out = dbgp_desc.bDebugOutEndpoint;
+
+	/* Move the device to 127 if it isn't already there */
+	if (devnum != USB_DEBUG_DEVNUM) {
+		ret = dbgp_control_msg(devnum,
+			USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+			USB_REQ_SET_ADDRESS, USB_DEBUG_DEVNUM, 0, NULL, 0);
+		if (ret < 0) {
+			dbgp_printk("Could not move attached device to %d\n", 
+				USB_DEBUG_DEVNUM);
+			goto err;
+		}
+		devnum = USB_DEBUG_DEVNUM;
+	}
+
+	/* Enable the debug interface */
+	ret = dbgp_control_msg(USB_DEBUG_DEVNUM,
+		USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+		USB_REQ_SET_FEATURE, USB_DEVICE_DEBUG_MODE, 0, NULL, 0);
+	if (ret < 0) {
+		dbgp_printk(" Could not enable the debug device\n");
+		goto err;
+	}
+
+	/* Perform a small write to get the even/odd data state in sync
+	 */
+	ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, dbgp_endpoint_out, " ",1);
+	if (ret < 0) {
+		dbgp_printk("dbgp_bulk_write failed: %d\n", ret);
+		goto err;
+	}
+
+
+	return;
+err:
+	/* Things didn't work so remove my claim */
+	ctrl = readl(&ehci_debug->control);
+	ctrl &= ~(DBGP_CLAIM | DBGP_OUT);
+	writel(ctrl, &ehci_debug->control);
+	return;
+}
+
+static void early_dbgp_write(struct console *con, const char *str, unsigned n)
+{
+	int chunk, ret;
+	if (!ehci_debug)
+		return;
+	while (n > 0) {
+		chunk = n;
+		if (chunk > DBGP_MAX_PACKET)
+			chunk = DBGP_MAX_PACKET;
+		ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, 
+			dbgp_endpoint_out, str, chunk);
+		str += chunk;
+		n -= chunk;
+	}
+}
+
+static struct console early_dbgp_console = {
+	.name =		"earlydbg",
+	.write =	early_dbgp_write,
+	.flags = 	CON_PRINTBUFFER,
+	.index = 	-1,
+};
+
+#endif
+
 /* Console interface to a host file on AMD's SimNow! */
 
 static int simnow_fd;
@@ -242,8 +804,20 @@ static int __init setup_early_printk(cha
  		simnow_init(buf + 6);
  		early_console = &simnow_console;
  		keep_early = 1;
+	} else if (!strncmp(buf, "dbgp", 4)) {
+		early_dbgp_init(buf + 4);
+		early_console = &early_dbgp_console;
 	}
 	register_console(early_console);
+#if DBGP_DEBUG
+	{
+		static const char dbgp_test_str[] = 
+			"The quick brown fox jumped over the lazy dog!\n";
+		early_dbgp_init("");
+		early_dbgp_write(&early_dbgp_console, 
+			dbgp_test_str, sizeof(dbgp_test_str) - 1);
+	}
+#endif
 	return 0;
 }
 
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index bbc3082..0a67192 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -46,6 +46,7 @@ struct ehci_stats {
 
 #define	EHCI_MAX_ROOT_PORTS	15		/* see HCS_N_PORTS */
 
+#ifndef EARLY_PRINTK
 struct ehci_hcd {			/* one per controller */
 	/* glue to PCI and HCD framework */
 	struct ehci_caps __iomem *caps;
@@ -160,6 +161,7 @@ timer_action (struct ehci_hcd *ehci, enu
 		mod_timer (&ehci->watchdog, t);
 	}
 }
+#endif /* EARLY_PRINTK */
 
 /*-------------------------------------------------------------------------*/
 
@@ -384,6 +386,7 @@ union ehci_shadow {
  * These appear in both the async and (for interrupt) periodic schedules.
  */
 
+#ifndef EARLY_PRINTK
 struct ehci_qh {
 	/* first part defined by EHCI spec */
 	__le32			hw_next;	 /* see EHCI 3.6.1 */
@@ -432,6 +435,7 @@ #define	QH_STATE_COMPLETING	5		/* don't 
 #define NO_FRAME ((unsigned short)~0)			/* pick new start */
 	struct usb_device	*dev;		/* access to TT */
 } __attribute__ ((aligned (32)));
+#endif /* EARLY_PRITNK */
 
 /*-------------------------------------------------------------------------*/
 
@@ -601,6 +605,8 @@ struct ehci_fstn {
 	union ehci_shadow	fstn_next;	/* ptr to periodic q entry */
 } __attribute__ ((aligned (32)));
 
+#ifndef EARLY_PRINTK
+
 /*-------------------------------------------------------------------------*/
 
 #ifdef CONFIG_USB_EHCI_ROOT_HUB_TT
@@ -659,4 +665,6 @@ #endif	/* DEBUG */
 
 /*-------------------------------------------------------------------------*/
 
+#endif /* EARLY_PRINTK */
+
 #endif /* __LINUX_EHCI_HCD_H */
diff --git a/include/asm-x86_64/fixmap.h b/include/asm-x86_64/fixmap.h
index 1b620db..1f2978a 100644
--- a/include/asm-x86_64/fixmap.h
+++ b/include/asm-x86_64/fixmap.h
@@ -36,6 +36,7 @@ enum fixed_addresses {
 	VSYSCALL_LAST_PAGE,
 	VSYSCALL_FIRST_PAGE = VSYSCALL_LAST_PAGE + ((VSYSCALL_END-VSYSCALL_START) >> PAGE_SHIFT) - 1,
 	VSYSCALL_HPET,
+	FIX_DBGP_BASE,
 	FIX_HPET_BASE,
 	FIX_APIC_BASE,	/* local (CPU) APIC) -- required for SMP or not */
 	FIX_IO_APIC_BASE_0,
-- 
1.4.2.rc3.g7e18e-dirty

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux