Re: 2.6.16.32 stuck in generic_file_aio_write()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

> If you are working on arcmsr 1.20.00.13 for official kernel version.
> This is the last version.

I'm already on that version. I'll see if I can upgrade to 2.6.19 today.

> Could you check your RAID controller event and tell someting to me?
> You can check "MBIOS"=>"Physical Drive Information"=>"View Drive 
> Information"=>"Select The Drive"=>"Timeout Count"......
> It could tell you which disk had bad behavior cause your RAID volume 
> offline.

I need to be in the BIOS right ? I couldn't find anything usefull with the 
cli32 tool.

> About the message dump from arcmsr, it said that your RAID volume had 
> something wrong and kicked out from the system.
> How about your RAID config?

CLI> disk info
Ch   ModelName        Serial#          FirmRev     Capacity  State
===============================================================================
 1   HDT722516DLA380  VDK71BTCDB90KE   V43OA91A     164.7GB  RaidSet 
Member(1)
 2   HDT722516DLA380  VDN71BTCDEPH7G   V43OA91A     164.7GB  RaidSet 
Member(1)
 3   HDT722516DLA380  VDN71BTCDES96G   V43OA91A     164.7GB  RaidSet 
Member(1)
 4   HDT722516DLA380  VDN71BTCDE15KG   V43OA91A     164.7GB  RaidSet 
Member(1)
===============================================================================

CLI> rsf info
Num Name             Disks TotalCap  FreeCap DiskChannels       State
===============================================================================
 1  Raid Set # 00        4  640.0GB    0.0GB 1234               Normal
===============================================================================

CLI> vsf info
 # Name             Raid# Level   Capacity Ch/Id/Lun  State
===============================================================================
 1 ARC-1110-VOL#00    1   Raid5    480.0GB 00/00/00   Normal
===============================================================================

A plain RAID 5 config with 4 disks. 


> Areca had new firmware released (1.42).
> If you are working on "sg" device with scsi passthrough ioctl method to feed 
> data into Areca's RAID volume.
> You need to limit your data under 512 blocks (256K) each transfer.
> The new firmware will enlarge it into 4096 blocks (2M) each transfer.
> The firmware version 1.42 is on releasing procedure but not yet put it on 
> Areca ftp site.

I don't use the sg driver at all. Is the upgrade worth it ? I usually 
don't mess with firmware unless being told to do so.

> If you need it, please tell me again.

Can you send it to me ? Installing it won't hurt I guess :)


Regards,


	Igmar


-- 
Igmar Palsenberg
JDI ICT

Zutphensestraatweg 85
6953 CJ Dieren
Tel: +31 (0)313 - 496741
Fax: +31 (0)313 - 420996
The Netherlands

mailto: [email protected]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux