(REG, Still broken sata (VIA) on Asus A8V (kernel 2.6.14+) with irqbalance)
Ok, a little late,
Heikki Orsila, can you send dmesg from working kernel
and /proc/interrupts too ?
and if you have a dmesg from a not working kernel can you send too ?
Vladimir B. Savkin , have you try the patch if so , please send the
results
Thanks,
On Sun, 2006-07-30 at 13:48 +0300, Heikki Orsila wrote:
> On Sat, Jul 29, 2006 at 05:08:09AM +0100, Sergio Monteiro Basto wrote:
> > cat DMESG | grep -i fixup
> > PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 0
> > PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 3
> > PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 3
> > PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 3
> >
> > with IO-APIC working , you could try patches to not "VIA IRQ quirk
> > fixup", but could not be the main problem.
> >
> > I have a very experimental patch
> > http://lkml.org/lkml/2006/7/28/99
> >
> >
> > Which you can just apply and make bzImage, install and reboot , don't
> > need to recompile all over again.
>
> Applied, tried and it worked! I couldn't reproduce the error in 30
> minutes of stress testing. With a buggy kernel it only took a matter of
> minutes to reproduce it. Thank you for your effort.
>
> Heikki Orsila
-------------
I was getting these sata messages after about 8 to 10 hours of uptime and the computer would freeze at least twice a day repeatedly for a week.
Oct 16 05:36:17 O1600 kernel: ata1: command 0x35 timeout, stat 0x50 host_stat 0x4
Oct 16 05:36:47 O1600 kernel: ata1: command 0xea timeout, stat 0x50 host_stat 0x0
I tried kernel 2.6.19-rc2 and I would get this message instead with the computer freezing.
Oct 15 00:04:36 O1600 kernel: APIC error on CPU0: 00(08)
I put in the patch mentioned below to get rid of the VIA IRQ fixup for a VIA K8T800 SMP machine and the computer hasn't froze yet after 19 hours.
The motherboard is a MSI K8T Master2-FAR with two Opteron 242s.
Here is the IRQ fixup messages pre patch running kernel 2.6.16.21-0.25-custom (SuSE 10.1):
<6>PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
<6>VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
<6>PCI: VIA IRQ fixup for 0000:00:10.0, from 10 to 1
<6>PCI: VIA IRQ fixup for 0000:00:10.1, from 10 to 1
<6>PCI: VIA IRQ fixup for 0000:00:10.2, from 11 to 1
Post patch I don't have any VIA fixup messages.
The lspci and interrupts look the same before and after the patch. eth0 and nvidia weren't irq balancing pre or post the patch - I'm not sure why.
Here is my interrupts: -post patch
CPU0 CPU1
0: 32807264 32848573 IO-APIC-edge timer
1: 1701 1693 IO-APIC-edge i8042
7: 0 2 IO-APIC-edge parport0
8: 0 0 IO-APIC-edge rtc
9: 0 1 IO-APIC-level acpi
12: 212960 207505 IO-APIC-edge i8042
14: 558126 566095 IO-APIC-edge ide0
15: 295527 293224 IO-APIC-edge ide1
169: 267097 277613 IO-APIC-level libata
177: 9915860 10 IO-APIC-level eth0, nvidia
185: 0 0 IO-APIC-level uhci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3, ehci_hcd:usb4
193: 30462 29909 IO-APIC-level EMU10K1
201: 0 3 IO-APIC-level ohci1394
209: 0 0 IO-APIC-level cx88[0]
NMI: 64698 64682
LOC: 65647942 65646061
ERR: 0
MIS: 0
Here is my lspci -vvv post patch
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [80] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW+ Rate=x8
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: e0000000-efffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: Creative Labs SB Audigy (rev 03)
Subsystem: Creative Labs SB0090 Audigy Player
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 193
Region 0: I/O ports at 9000 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.1 Input device controller: Creative Labs SB Audigy MIDI/Game port (rev 03)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at 9400 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size 08
Interrupt: pin B routed to IRQ 201
Region 0: Memory at fb014000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fb010000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:08.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: ATI Technologies Inc ATI TV Wonder Pro
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 13750ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 209
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705 Gigabit Ethernet (rev 03)
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (16000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 177
Region 0: Memory at fb000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: ffffff7ffffffdf4 Data: ffff
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin B routed to IRQ 169
Region 0: I/O ports at 9800 [size=8]
Region 1: I/O ports at 9c00 [size=4]
Region 2: I/O ports at a000 [size=8]
Region 3: I/O ports at a400 [size=4]
Region 4: I/O ports at a800 [size=16]
Region 5: I/O ports at ac00 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 169
Region 4: I/O ports at b000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 185
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 185
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 185
Region 4: I/O ports at bc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 10
Interrupt: pin C routed to IRQ 185
Region 0: Memory at fb015000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
Subsystem: Micro-Star International Co., Ltd. Unknown device 1300
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: nVidia Corporation NV36.1 [GeForce FX 5700 Ultra] (rev a1) (prog-if 00 [VGA])
Subsystem: Chaintech Computer Co. Ltd Unknown device 194c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 177
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
[virtual] Expansion ROM at f9000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW+ Rate=x8
Thanks,
Dyson
-----------------------------------------------------------------
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
