Re: suspend broken in 2.6.18.1

[Eric Sandall <eric@sandall.us>]

Pavel Machek wrote:
> Hi!
> 
>> After updating from 2.6.17.13 to 2.6.18 (using `make oldconfig`),
>> suspend no longer suspends my laptop (Dell Inspiron 5100).
>>
>> # s2ram -f
>> Switching from vt7 to vt1
>> s2ram_do: Invalid argument
>> switching back to vt7
>>
>> The screen blanks, but then comes back up after a few seconds. This
>> happens both with and without X running.
>>
>> I've attached the output of `lspci -vvv` and my
>> /usr/src/linux-2.6.18/.config for more information. Please let me know
>> if there are any patches to try or if more information is required.
> 
> Relevant part of dmesg after failed attempt is neccessary... and you
> can probably read it yourself and figure what is wrong. I'd guess some
> device just failed to suspend... rmmod it.

(This is now with 2.6.18.1)

Stopping tasks: =====================================================|
ACPI: PCI interrupt for device 0000:02:04.0 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
Class driver suspend failed for cpu0
Could not power down device firmware: error -22
Some devices failed to power down

I've attached my entire dmesg as well.

-sandalle

-- 
Eric Sandall                     |  Source Mage GNU/Linux Developer
eric@sandall.us                  |  http://www.sourcemage.org/
http://eric.sandall.us/          |  SysAdmin @ Shock Physics @ WSU
http://counter.li.org/  #196285  |  http://www.shock.wsu.edu/

808
Allocating PCI resources starting at 50000000 (gap: 40000000:beda0000)
Detected 2392.116 MHz processor.
Built 1 zonelists.  Total pages: 262089
Kernel command line: root=/dev/hdc1
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01803000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1033064k/1048356k available (2274k kernel code, 14496k reserved, 711k data, 260k init, 130852k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4791.78 BogoMIPS (lpj=2395894)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2000k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfcfae, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
Intel 82802 RNG detected
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: c000-cfff
  MEM window: fc000000-fdffffff
  PREFETCH window: e8000000-efffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
  IO window: 0000d000-0000d0ff
  IO window: 0000d400-0000d4ff
  PREFETCH window: 50000000-51ffffff
  MEM window: f6000000-f7ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-efff
  MEM window: f6000000-fbffffff
  PREFETCH window: 50000000-51ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:04.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1161033919.628:1): initialized
highmem bounce pool size: 64 pages
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
ACPI: Video Device [VID2] (multi-head: yes  rom: no  post: no)
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (76 C)
Real Time Clock Driver v1.12ac
RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HL-DT-STCD-RW/DVD-ROM GCC-4240N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: FUJITSU MHT2030AT, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 128KiB
hdc: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(100)
hdc: cache flushes supported
 hdc: hdc1 hdc2
hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
i8042.c: Warning: Keylock active.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
input: AT Translated Set 2 keyboard as /class/input/input0
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-2)
Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.5 to 64
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x254ab1, caps: 0x804713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
intel8x0_measure_ac97_clock: measured 50992 usecs
intel8x0: clocking to 48000
ALSA device list:
  #0: Intel 82801DB-ICH4 with STAC9750,51 at 0xf4fff800, irq 7
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 2000KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (ext2 filesystem).
ReiserFS: hdc1: found reiserfs format "3.6" with standard journal
ReiserFS: hdc1: using ordered data mode
ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc1: checking transaction log (hdc1)
ReiserFS: hdc1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... /initrd does not exist. Ignored.
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 260k freed
Linux agpgart interface v0.101 (c) Dave Jones
usbcore: registered new driver usbfs
usbcore: registered new driver hub
agpgart: Detected an Intel 845G Chipset.
agpgart: AGP aperture is 128M @ 0xe0000000
Yenta: CardBus bridge found at 0000:02:04.0 [1028:0149]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x00001002, devctl 0x64
ieee1394: Initialized config rom entry `ip1394'
USB Universal Host Controller Interface driver v3.0
Yenta: ISA IRQ mask 0x0478, PCI irq 11
Socket status: 30000086
Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xefff
cs: IO port probe 0xd000-0xefff: clean.
pcmcia: parent PCI bridge Memory window: 0xf6000000 - 0xfbffffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
ACPI: PCI Interrupt 0000:02:04.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11]  MMIO=[faffb800-faffbfff]  Max Packet=[2048]  IR/IT contexts=[4/8]
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0d:56:31:21:10
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[4a4fc0003dc1a861]
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
drm: version magic '2.6.17.13 preempt mod_unload PENTIUM4 gcc-4.0' should be '2.6.18.1 preempt mod_unload PENTIUM4 gcc-4.0'
radeon: version magic '2.6.17.13 preempt mod_unload PENTIUM4 gcc-4.0' should be '2.6.18.1 preempt mod_unload PENTIUM4 gcc-4.0'
fuse init (API version 7.7)
fuse distribution version: 2.6.0-rc1
Adding 1470664k swap on /dev/hdc2.  Priority:-1 extents:1 across:1470664k
ndiswrapper version 1.26 loaded (preempt=yes,smp=no)
ndiswrapper: driver bcmwl5 (Broadcom,02/10/2005, 3.100.35.1) loaded
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ndiswrapper: using IRQ 11
wlan0: vendor: ''
wlan0: ethernet device 00:90:4b:2d:98:01 using NDIS driver bcmwl5, 14E4:4320:1028:0001.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
usbcore: registered new driver ndiswrapper
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8190 buckets, 65520 max) - 192 bytes per conntrack
ip6_tables: (C) 2000-2006 Netfilter Core Team
drm: version magic '2.6.17.13 preempt mod_unload PENTIUM4 gcc-4.0' should be '2.6.18.1 preempt mod_unload PENTIUM4 gcc-4.0'
radeon: version magic '2.6.17.13 preempt mod_unload PENTIUM4 gcc-4.0' should be '2.6.18.1 preempt mod_unload PENTIUM4 gcc-4.0'
Stopping tasks: =====================================================|
ACPI: PCI interrupt for device 0000:02:04.0 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
Class driver suspend failed for cpu0
Could not power down device firmware: error -22
Some devices failed to power down
PCI: Enabling device 0000:00:1d.0 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 400, writing 40b)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing f4fffc00)
PM: Writing back config space on device 0000:00:1d.7 at offset 1 (was 2900006, writing 2900106)
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:00:1f.5 (0000 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:02:04.0 at offset 1 (was 2100000, writing 2100007)
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Restarting tasks... done