Re: [Bug 7174] New: init run before all EXT3 drives are detected, stopping init

[Andrew Morton <akpm@osdl.org>]

(Switched from bugzilla to email.  Please retaain all cc's).

On Wed, 20 Sep 2006 14:27:56 -0700
bugme-daemon@bugzilla.kernel.org wrote:

> http://bugzilla.kernel.org/show_bug.cgi?id=7174
> 
>            Summary: init run before all EXT3 drives are detected, stopping
>                     init
>     Kernel Version: 2.6.18
>             Status: NEW
>           Severity: low
>              Owner: akpm@osdl.org
>          Submitter: ajberry@usa.net
> 
> 
> Most recent kernel where this bug did not occur:
> Distribution:
> Hardware Environment:
> Intel DG965MS  (ICH8)
> 2 GB Ram
> 200GB Sata II Hard Drive 2 ext3 partitions, 1 swap
> 
> Software Environment:
> Ubuntu 6.06.1 Desktop
> All of EXT3 and SATA is Build into the kernel, no initrd at boottime.
> 
> Problem Description:
> When booting init starts running fsck and /dev/sda2 is "no such file or
> directory".  Boot stops and Control-D must be pressed. After this the partition
> is dectected and the drive comes up and is properly mounted. I can boot 2.6.15
> with out this problem (but with acpi=off).  I have not run into this on other
> systems with similar configurations with 2.6.16/17.
> 
> Excpert From Console Log:
>  * Checking all filesystems...        fsck.ext3: No such file or directory
> while trying to open /dev/sda2
> 
> /dev/sda2: 
> The superblock could not be read or does not describe a correct ext2
> filesystem.  If the device is valid and it really contains an ext2
> filesystem (and not swap or ufs or something else), then the superblock
> is corrupt, and you might try running e2fsck with an alternate superblock:
>     e2fsck -b 8193 <device>
> 
> 
> [ ok ]
>  * File system check failed.  Please repair manually.
>  * CONTROL-D will exit from this shell and continue syste[  
> 68.657843] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
> m startup.
> root@ubuntu:~# [   70.313668] NET: Registered protocol family 10
> [   70.318177] lo: Disabled Privacy Extensions
> [   70.322825] IPv6 over IPv4 tunneling driver
> exit
> [   77.191994] kjournald starting.  Commit interval 5 seconds
> [   77.192165] EXT3 FS on sda2, internal journal
> [   77.192170] EXT3-fs: mounted filesystem with ordered data mode.
> [   77.234688] Adding 1036184k swap on /dev/sda3.  Priority:-1 extents:1
> across:1036184k
>  * Configuring network interfaces...        
> [ ok ]
> 
>  * INIT: Entering runlevel: 2
> 

What version of udev are you running?

All I can think of is that udev was too slow in creating the /dev/sda2
device node.  I could understand that happening if the sata drivers were
modular (perhaps), but you have CONFIG_SCSI_SATA=y CONFIG_SCSI_SATA_AHCI=y,
CONFIG_SCSI_ATA_PIIX=y.

[ lots snipped - it's at http://bugzilla.kernel.org/show_bug.cgi?id=7174 ]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/