On (01/09/06 20:24), Paul Jackson didst pronounce:
> > That is a bit of a sickener. It may be worth getting your good lab tech
> > to check if there is a configuration setting in the hardware for
> > simulating console output before you make the trip.
>
> Apparently my lab setup simply lacks correct flow control on the serial
> console line. I hacked the 8250 serial driver in my kernel to put a one
> msec delay between each character output, and it no longer drops
> console output during boot.
>
Nice work.
> > > This may take a day or three to yield results, unless I get lucky.
> > >
> >
> > I have Keith's problem with reserve-based-hot-add to keep me occupied in
> > the meantime. Whenever you get the chance will be fine. Thanks a lot
>
> Ok, below is the console output for one of these crashes.
>
> This output is missing the first couple dozen lines commencing with
> grub announcing it is loading my kernel, as those lines seem to go via
> a different serial driver that I didn't chase down to hack. Those
> initial lines were still dropping lotsa chars. If you need those
> initial lines bad, holler, and I can probably hack something to get
> them to show up.
>
I could do with those lines, but I believe there was enough information
printed to determine why it failed to boot. I've attached a patch that
should boot the machine and assuming it works, I just need the output of
dmesg.
> By the way, the crash continues to happen 100% with the patch:
>
> patches/account-for-memmap-and-optionally-the-kernel-image-as-holes.patch
>
Not suprising considering what the min_free_kbytes is from this output!
> Node 0 DMA free:1616kB min:143085642166168kB low:178857052707708kB high:214628463249252kB active:0kB inactive:0kB present:18446744073709538996kB pages_scanned:0 all_unreclaimable? yes
> lowmem_reserve[]: 0 2026 2026
> Node 0 DMA32 free:2036328kB min:5776kB low:7220kB high:8664kB active:0kB inactive:0kB present:2075356kB pages_scanned:0 all_unreclaimable? no
>
I believe it is because memmap was calculated to be bigger than it
possibly could be. Can you try booting the following patch with
loglevel=8 and send me the dmesg output if it boots please? Thanks
diff -rup -X /usr/src/patchset-0.6/bin//dontdiff linux-2.6.18-rc4-mm3-clean/mm/page_alloc.c linux-2.6.18-rc4-mm3-fix_accountmemmap/mm/page_alloc.c
--- linux-2.6.18-rc4-mm3-clean/mm/page_alloc.c 2006-08-28 15:05:30.000000000 +0100
+++ linux-2.6.18-rc4-mm3-fix_accountmemmap/mm/page_alloc.c 2006-09-04 10:36:04.000000000 +0100
@@ -2373,7 +2373,9 @@ unsigned long __meminit account_memmap(s
if (zone_index == memmap_zone_idx(pgdat->node_mem_map)) {
pages = pgdat->node_spanned_pages;
pages = (pages * sizeof(struct page)) >> PAGE_SHIFT;
- printk(KERN_DEBUG "%lu pages used for memmap\n", pages);
+ printk(KERN_DEBUG
+ " %s zone: %lu pages used for memmap\n",
+ zone_names[zone_index], pages);
}
return pages;
}
@@ -2411,7 +2413,9 @@ unsigned long account_memmap(struct pgli
}
pages >>= PAGE_SHIFT;
- printk(KERN_DEBUG "%lu pages used for SPARSE memmap\n", pages);
+ printk(KERN_DEBUG
+ " %s zone: %lu pages used for SPARSEMEM memmap\n",
+ zone_names[zone_index], pages);
return pages;
}
#endif
@@ -2437,17 +2441,24 @@ static void __meminit free_area_init_cor
for (j = 0; j < MAX_NR_ZONES; j++) {
struct zone *zone = pgdat->node_zones + j;
- unsigned long size, realsize;
+ unsigned long size, realsize, memmap_size;
size = zone_spanned_pages_in_node(nid, j, zones_size);
realsize = size - zone_absent_pages_in_node(nid, j,
zholes_size);
- realsize -= account_memmap(pgdat, j);
+ /* Account for the size of mem_map */
+ memmap_size = account_memmap(pgdat, j);
+ if (realsize >= memmap_size)
+ realsize -= memmap_size;
+ else
+ printk(KERN_WARNING "memmap_size of %lu exceeds %lu\n",
+ memmap_size, realsize);
+
/* Account for reserved DMA pages */
if (j == ZONE_DMA && realsize > dma_reserve) {
realsize -= dma_reserve;
- printk(KERN_DEBUG "%lu pages DMA reserved\n",
+ printk(KERN_DEBUG " DMA zone: %lu pages reserved\n",
dma_reserve);
}
--
VGER BF report: U 0.499996
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]