Re: qlogic 2312 problems on 2.6.16.22, 2.6.18rc4

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wednesday 16 August 2006 20:14, Andrew Vasquez wrote:

> > Everything works fine on 32-bit dual xeon machine with card inserted into
> > PCI slot. Here in new dual core opteron machine the card sits in PCI-X
> > slot. It's Thunder K8SRE S2891 mainboard, Transport GT24 B2891 1U
> > barebone, Tyan M2075 riser card, 2 x Opteron 270, 6GB ram.
>
> Have you ruled out motherboard/memory issues?  We've run 23xx and 24xx
> boards on a variety of AMD64 motherboards with more than 4GB of
> memory.
Not exactly. I have three such servers (the same board, cpu, ram).

One of these has PCI-E scsi raid controller and works without any problem. 

Second one (which I'm using for testing) has Adaptec SCSI controller 
in Tyan specific TARRO slot (which afaik sits on the same PCI-X bus as PCI-X slot).
I had an array on that adaptec for some time and there were no problems.
The second one also got own qlogic 2312 card.

Third machine has other qlogic 2312 card and I tried it two times,
too - the same issues observed.

So mainboards and memory should be fine but I guess there is possibility
that PCI-X slot is somehow broken there. I'll test that in several weeks
(unfortunately I have no physical access to these now) by putting some
typical scsi controller into that pci-x slot.

> > Note that booting with 32-bit kernel (which works fine on Xeon system)
> > doesn't cure the problem on Opteron system. Booting 64bit 2.6.18rc4
> > kernel with mem=3G also doesn't fix anything.
>
> Hmm...  Can you send your dmesg output post boot and driver load?

dmesg and lspci -vvv attached.

There is one thing that worries me:
  QLogic QLA2340 - 
  ISP2312: PCI-X (133 MHz) @ 0000:09:08.0 hdma+, host#=0, fw=3.03.20 IPX

Why it's showing 133MHz here? 

Tyan manual ftp://ftp.tyan.com/manuals/m_s2891_100.pdf says on page 4
,,One PCI-X 100MHz slot (PCI-X B)''.

Hm, while looking at that manual I see that on page 13 it says ,,one pci-x 100MHz device''.
Maybe that's the problem since I didn't remove Adaptec TARO controller. I should be able to
get this tested again without adaptec sooner than several weeks. Maybe I misunderstand
what documentation says here.

Anyway still don't know why driver displays 133Mhz while manual says about
100MHz one pci-x slot.

> > /t is on tmpfs, /dev/sda2 in on FC array. Reading the same data several
> > times and I get different md5sum results each time, see below.
> >
> > How I can track where corruption occurs?

I started dd'ing text file onto /dev/sda2, then back to tmpfs and diffing these. Corruption
is one byte, several not corrupted bytes and again one corrupted byte. Some regular pattern.

>
> Regards,
> Andrew Vasquez

Bootdata ok (command line is initrd=/initrd-test.gz init=/linuxrc root=/dev/ram0 ramdisk_size=54000 console=tty0 console=ttyS0,115200n81 panic=60 BOOT_IMAGE=vmlinuz-test ip=192.168.0.127:192.168.0.1:192.168.0.1:255.255.255.0 )
Linux version 2.6.18-rc4-dirty (root@db01new) (gcc version 3.3.6 (PLD Linux)) #7 Wed Aug 16 22:43:23 CEST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
 BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
 BIOS-e820: 000000007ff90000 - 000000007ff99000 (ACPI data)
 BIOS-e820: 000000007ff99000 - 0000000080000000 (ACPI NVS)
 BIOS-e820: 0000000080000000 - 00000000bff80000 (usable)
 BIOS-e820: 00000000bff80000 - 00000000c0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000e8000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 00000001c0000000 (usable)
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x00000000000f7040
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x000000007ff95407
ACPI: FADT (v001 NVIDIA CK8S     0x06040000 PTL_ 0x000f4240) @ 0x000000007ff98d72
ACPI: SRAT (v001 AMD    HAMMER   0x06040000 AMD  0x00000001) @ 0x000000007ff98de6
ACPI: SPCR (v001 PTLTD  $UCRTBL$ 0x06040000 PTL  0x00000001) @ 0x000000007ff98ef6
ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @ 0x000000007ff98f46
ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x000000007ff98fd8
ACPI: DSDT (v001 NVIDIA      CK8 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 1545657
  DMA zone: 2161 pages, LIFO batch:0
  DMA32 zone: 767816 pages, LIFO batch:31
  Normal zone: 775680 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:1 APIC version 16
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2 15:1 APIC version 16
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 15:1 APIC version 16
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xdf200000] gsi_base[24])
IOAPIC[1]: apic_id 5, version 17, address 0xdf200000, GSI 24-27
ACPI: IOAPIC (id[0x06] address[0xdf201000] gsi_base[28])
IOAPIC[2]: apic_id 6, version 17, address 0xdf201000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
Built 1 zonelists.  Total pages: 1545657
Kernel command line: initrd=/initrd-test.gz init=/linuxrc root=/dev/ram0 ramdisk_size=54000 console=tty0 console=ttyS0,115200n81 panic=60 BOOT_IMAGE=vmlinuz-test ip=192.168.0.127:192.168.0.1:192.168.0.1:255.255.255.0 
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2009.273 MHz processor.
Console: colour VGA+ 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      8192
... CHAINHASH_SIZE:          4096
 memory used by lock dependency info: 1120 kB
 per task-struct memory footprint: 1680 bytes
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Checking aperture...
CPU 0: aperture @ c0000000 size 256 MB
CPU 1: aperture @ c0000000 size 256 MB
Memory: 6168496k/7340032k available (2114k kernel code, 121284k reserved, 1130k data, 192k init)
Calibrating delay using timer specific routine.. 4021.70 BogoMIPS (lpj=8043410)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: Dual Core AMD Opteron(tm) Processor 270 stepping 02
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12557973
Detected 12.557 MHz APIC timer.
testing NMI watchdog ... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 780k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:07.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Root Bridge [PCI2] (0000:08)
PCI: Probing PCI hardware (bus 08)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PB._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ c0000000 size 262144 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 256MB of IOMMU area in the AGP aperture
pnp: 00:08: ioport range 0x8000-0x807f could not be reserved
pnp: 00:08: ioport range 0x8080-0x80ff has been reserved
pnp: 00:08: ioport range 0x8400-0x847f has been reserved
pnp: 00:08: ioport range 0x8480-0x84ff has been reserved
pnp: 00:08: ioport range 0x8800-0x887f has been reserved
pnp: 00:08: ioport range 0x8880-0x88ff has been reserved
pnp: 00:08: ioport range 0x5000-0x503f has been reserved
pnp: 00:08: ioport range 0x5040-0x507f has been reserved
PCI: Bridge: 0000:00:09.0
  IO window: 2000-2fff
  MEM window: dd100000-deffffff
  PREFETCH window: c2000000-c20fffff
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Bridge: 0000:08:0a.0
  IO window: 3000-3fff
  MEM window: df300000-df3fffff
  PREFETCH window: c2100000-c21fffff
PCI: Bridge: 0000:08:0b.0
  IO window: disabled.
  MEM window: df400000-df4fffff
  PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 32768 (order: 9, 2359296 bytes)
TCP bind hash table entries: 16384 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 32768 bind 16384)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1155768349.728:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for subordinate bus.
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for subordinate bus.
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:02: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 54000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
IP-Config: No network devices available.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (romfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
tg3.c:v3.64 (July 31, 2006)
GSI 16 sharing vector 0xC1 and IRQ 16
ACPI: PCI Interrupt 0000:0a:09.0[A] -> GSI 28 (level, low) -> IRQ 193
eth0: Tigon3 [partno(BCM95704) rev 2003 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:33:5e:ae
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0] 
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
GSI 17 sharing vector 0xC9 and IRQ 17
ACPI: PCI Interrupt 0000:0a:09.1[B] -> GSI 29 (level, low) -> IRQ 201
eth1: Tigon3 [partno(BCM95704) rev 2003 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:33:5e:af
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] 
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
PM: Writing back config space on device 0000:0a:09.0 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device 0000:0a:09.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:0a:09.0 at offset 1 (was 2b00000, writing 2b00106)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
SCSI subsystem initialized
QLogic Fibre Channel HBA Driver
GSI 18 sharing vector 0xD1 and IRQ 18
ACPI: PCI Interrupt 0000:09:08.0[A] -> GSI 24 (level, low) -> IRQ 209
qla2xxx 0000:09:08.0: Found an ISP2312, irq 209, iobase 0xffffc20000004000
qla2xxx 0000:09:08.0: Configuring PCI space...
qla2xxx 0000:09:08.0: Configure NVRAM parameters...
qla2xxx 0000:09:08.0: Verifying loaded RISC code...
scsi(0): **** Load RISC code ****
scsi(0): Verifying Checksum of loaded RISC code.
scsi(0): Checksum OK, start firmware.
qla2xxx 0000:09:08.0: Allocated (412 KB) for firmware dump...
scsi(0): Issue init firmware.
scsi(0): Asynchronous LIP RESET (f7f7).
qla2xxx 0000:09:08.0: LIP reset occured (f7f7).
qla2xxx 0000:09:08.0: Waiting for LIP to complete...
scsi(0): Asynchronous P2P MODE received.
scsi(0): Asynchronous LOOP UP (2 Gbps).
qla2xxx 0000:09:08.0: LOOP UP detected (2 Gbps).
scsi(0): Asynchronous PORT UPDATE.
scsi(0): Port database changed ffff 0006 0000.
scsi(0): F/W Ready - OK 
scsi(0): fw_state=3 curr time=ffff0467.
qla2xxx 0000:09:08.0: Topology - (F_Port), Host Loop address 0xffff
scsi(0): Configure loop -- dpc flags =0x4080040
scsi(0): RSCN queue entry[0] = [00/000000].
scsi(0): device_resync: rscn overflow.
scsi(0): RFT_ID exiting normally.
scsi(0): RFF_ID exiting normally.
scsi(0): RNN_ID exiting normally.
scsi(0): RSNN_NN exiting normally.
scsi(0): Asynchronous PORT UPDATE ignored 0000/0006/bd92.
scsi(0): GID_PT entry - nn 500508b300917e50 pn 500508b300917e51 portid=010000.
scsi(0): GID_PT entry - nn 200000e08b8051d6 pn 210000e08b8051d6 portid=010100.
scsi(0): GID_PT entry - nn 200000e08b950428 pn 210000e08b950428 portid=010200.
scsi(0): device wrap (010200)
scsi(0): Trying Fabric Login w/loop id 0x0081 for port 010000.
scsi(0): Trying Fabric Login w/loop id 0x0082 for port 010100.
qla2x00_mailbox_command(0): **** FAILED. mbx0=4007, mbx1=0, mbx2=100, cmd=6f ****
qla2x00_login_fabric(0): failed=102 mb[0]=4007 mb[1]=0 mb[2]=100.
Fabric Login: port in use - next loop id=0x0000, port Id=010100.
scsi(0): Trying Fabric Login w/loop id 0x0000 for port 010100.
scsi(0): LOOP READY
DEBUG: detect hba 0 at address = ffff8101bd9807e0
scsi0 : qla2xxx
qla2xxx 0000:09:08.0: 
 QLogic Fibre Channel HBA Driver: 8.01.05-k3
  QLogic QLA2340 - 
  ISP2312: PCI-X (133 MHz) @ 0000:09:08.0 hdma+, host#=0, fw=3.03.20 IPX
  Vendor: COMPAQ    Model: MSA1000           Rev: 4.96
  Type:   RAID                               ANSI SCSI revision: 04
  Vendor: COMPAQ    Model: MSA1000 VOLUME    Rev: 4.96
  Type:   Direct-Access                      ANSI SCSI revision: 04
  Vendor: COMPAQ    Model: MSA1000 VOLUME    Rev: 4.96
  Type:   Direct-Access                      ANSI SCSI revision: 04
scsi(0): Asynchronous PORT UPDATE ignored 0001/0006/bd92.
scsi(0): Asynchronous PORT UPDATE ignored 0001/0007/bd92.
scsi(0): Asynchronous PORT UPDATE ignored 0001/0004/bd92.
SCSI device sda: 513790830 512-byte hdwr sectors (263061 MB)
sda: Write Protect is off
sda: Mode Sense: 83 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 513790830 512-byte hdwr sectors (263061 MB)
sda: Write Protect is off
sda: Mode Sense: 83 00 00 08
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:2: Attached scsi disk sda
SCSI device sdb: 1381590 512-byte hdwr sectors (707 MB)
sdb: Write Protect is off
sdb: Mode Sense: 83 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 1381590 512-byte hdwr sectors (707 MB)
sdb: Write Protect is off
sdb: Mode Sense: 83 00 00 08
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2
 sdb: p2 exceeds device capacity
sd 0:0:0:4: Attached scsi disk sdb


00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [44] HyperTransport: Slave or Primary Interface
		Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
		Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
		Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
		Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
		Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
		Revision ID: 1.03
		Link Frequency 0: 800MHz
		Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
		Link Frequency 1: 200MHz
		Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
		Prefetchable memory behind bridge Upper: 00-00
		Bus Number: 00
	Capabilities: [e0] HyperTransport: MSI Mapping

00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 0: I/O ports at <ignored>

00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 0
	Region 0: I/O ports at 1000 [size=32]
	Region 4: I/O ports at 5000 [size=64]
	Region 5: I/O ports at 5040 [size=64]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin B routed to IRQ 7
	Region 0: Memory at dd001000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [44] Debug port
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Region 4: I/O ports at 1400 [size=16]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 1440 [size=8]
	Region 1: I/O ports at 1434 [size=4]
	Region 2: I/O ports at 1438 [size=8]
	Region 3: I/O ports at 1430 [size=4]
	Region 4: I/O ports at 1410 [size=16]
	Region 5: Memory at dd002000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 1458 [size=8]
	Region 1: I/O ports at 144c [size=4]
	Region 2: I/O ports at 1450 [size=8]
	Region 3: I/O ports at 1448 [size=4]
	Region 4: I/O ports at 1420 [size=16]
	Region 5: Memory at dd003000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: dd100000-deffffff
	Prefetchable memory behind bridge: c2000000-c20fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size 10
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
		Address: 00000000fee00000  Data: 40b9
	Capabilities: [58] HyperTransport: MSI Mapping
	Capabilities: [80] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 <4us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
		Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 0
		Link: Latency L0s <512ns, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x16
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
		Slot: Number 0, PowerLimit 0.000000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
		Slot: AttnInd Unknown, PwrInd Unknown, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Revision ID: 1.02
	Capabilities: [a0] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Revision ID: 1.02
	Capabilities: [c0] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Revision ID: 1.02

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Revision ID: 1.02
	Capabilities: [a0] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
		Revision ID: 1.02
	Capabilities: [c0] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
		Revision ID: 1.02

00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

01:07.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
	Subsystem: ATI Technologies Inc Rage XL
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66 (2000ns min), Cache Line Size 10
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at 2000 [size=256]
	Region 2: Memory at dd100000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at c2000000 [disabled] [size=128K]
	Capabilities: [5c] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

08:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Bus: primary=08, secondary=09, subordinate=09, sec-latency=72
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: df300000-df3fffff
	Prefetchable memory behind bridge: 00000000c2100000-00000000c2100000
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR+
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [a0] PCI-X bridge device
		Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
		Status: Dev=08:0a.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
		Upstream: Capacity=14 CommitmentLimit=65535
		Downstream: Capacity=2 CommitmentLimit=65535
	Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
	Capabilities: [c0] HyperTransport: Slave or Primary Interface
		!!! Possibly incomplete decoding
		Command: BaseUnitID=10 UnitCnt=2 MastHost- DefDir-
		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
		Link Config 1: MLWI=8bit MLWO=8bit LWI=N/C LWO=N/C
		Revision ID: 1.02

08:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 0: Memory at df200000 (64-bit, non-prefetchable) [size=4K]

08:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Bus: primary=08, secondary=0a, subordinate=0a, sec-latency=64
	Memory behind bridge: df400000-df4fffff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [a0] PCI-X bridge device
		Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
		Status: Dev=08:0b.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
		Upstream: Capacity=14 CommitmentLimit=65535
		Downstream: Capacity=2 CommitmentLimit=65535
	Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration

08:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
	Subsystem: Tyan Computer Unknown device 2891
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 0: Memory at df201000 (64-bit, non-prefetchable) [size=4K]

09:08.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev 02)
	Subsystem: Compaq Computer Corporation Unknown device 0100
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 128 (16000ns min), Cache Line Size 10
	Interrupt: pin A routed to IRQ 209
	Region 0: I/O ports at 3000 [size=256]
	Region 1: Memory at df300000 (64-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at c2180000 [disabled] [size=128K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [4c] PCI-X non-bridge device
		Command: DPERE- ERO+ RBC=1024 OST=2
		Status: Dev=09:08.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=4096 DMOST=3 DMCRS=32 RSCEM- 266MHz- 533MHz-
	Capabilities: [54] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [64] #06 [0080]

09:0a.0 SCSI storage controller: Adaptec AIC-7901 U320 (rev 10)
	Subsystem: Adaptec Unknown device 005f
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 72 (10000ns min, 6250ns max), Cache Line Size 10
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 3800 [size=256]
	Region 1: Memory at df302000 (64-bit, non-prefetchable) [size=8K]
	Region 3: I/O ports at 3400 [size=256]
	[virtual] Expansion ROM at c2100000 [disabled] [size=512K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a0] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [94] PCI-X non-bridge device
		Command: DPERE- ERO+ RBC=512 OST=3
		Status: Dev=09:0a.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-

0a:09.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
	Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (16000ns min), Cache Line Size 10
	Interrupt: pin A routed to IRQ 193
	Region 0: Memory at df410000 (64-bit, non-prefetchable) [size=64K]
	Region 2: Memory at df400000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] PCI-X non-bridge device
		Command: DPERE- ERO- RBC=2048 OST=1
		Status: Dev=0a:09.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
		Address: 0000000100000000  Data: 00a0

0a:09.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
	Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (16000ns min), Cache Line Size 10
	Interrupt: pin B routed to IRQ 201
	Region 0: Memory at df430000 (64-bit, non-prefetchable) [size=64K]
	Region 2: Memory at df420000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] PCI-X non-bridge device
		Command: DPERE- ERO- RBC=2048 OST=1
		Status: Dev=0a:09.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
		Address: 0000000100000000  Data: 0000



-- 
Arkadiusz Miśkiewicz        PLD/Linux Team
arekm / maven.pl            http://ftp.pld-linux.org/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux