[PATCH] amd74xx: implement suspend-to-ram

["Rafael J. Wysocki" <rjw@sisk.pl>]

From: Jason Lunz <lunz@falooley.org>

The amd74xx driver needs to reprogram each drive's PIO timings as well
as the DMA timings on resume from s2ram.  Otherwise, my
nforce3-150-based laptop hangs hard when ide_start_power_step() calls
drive->hwif->ide_dma_check(drive).

Suspend/resume from ram now works with the disk and the cdrom under
load, both with and without DMA enabled.

I'm hardcoding a maximum of 2 ide channels, but other aspects of this
driver (like the amd_80w global) are already doing that.

DMA is re-enabled on resume even if it wasn't on at suspend, but that
doesn't look unusual in drivers/ide/pci.

Signed-off-by: Jason Lunz <lunz@falooley.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/ide/pci/amd74xx.c |   57 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 57 insertions(+)

Index: linux-2.6.18-rc2-git1/drivers/ide/pci/amd74xx.c
--- linux-2.6.18-rc2-git1.orig/drivers/ide/pci/amd74xx.c
+++ linux-2.6.18-rc2-git1/drivers/ide/pci/amd74xx.c
@@ -83,6 +83,8 @@
 static ide_pci_device_t *amd_chipset;
 static unsigned int amd_80w;
 static unsigned int amd_clock;
+#define AMD_MAX_CHANNELS	(2)
+static ide_hwif_t *amd_hwifs[AMD_MAX_CHANNELS];
 
 static char *amd_dma[] = { "MWDMA16", "UDMA33", "UDMA66", "UDMA100", "UDMA133" };
 static unsigned char amd_cyc2udma[] = { 6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7 };
@@ -416,6 +418,8 @@
 {
 	int i;
 
+	amd_hwifs[hwif->channel] = hwif;
+
 	if (hwif->irq == 0) /* 0 is bogus but will do for now */
 		hwif->irq = pci_get_legacy_ide_irq(hwif->pci_dev, hwif->channel);
 
@@ -494,6 +498,55 @@
 	/* 19 */ DECLARE_AMD_DEV("AMD5536"),
 };
 
+#ifdef	CONFIG_PM
+
+static int amd74xx_suspend(struct pci_dev *dev, pm_message_t state)
+{
+	pci_save_state(dev);
+
+	if (state.event == PM_EVENT_SUSPEND) {
+		pci_disable_device(dev);
+		pci_set_power_state(dev, PCI_D3hot);
+	}
+	return 0;
+}
+
+static int amd74xx_resume(struct pci_dev *dev)
+{
+	int retval = 0;
+	int i;
+
+	pci_set_power_state(dev, PCI_D0);
+	retval = pci_enable_device(dev);
+	pci_restore_state(dev);
+
+	for (i = 0; i < AMD_MAX_CHANNELS; i++) {
+		int d;
+
+		if (!amd_hwifs[i])
+			continue;
+
+		for (d = 0; d < MAX_DRIVES; ++d) {
+			ide_drive_t *drive = &amd_hwifs[i]->drives[d];
+			if (drive->present && !__ide_dma_bad_drive(drive)) {
+				/* this is the primary reason this driver needs
+				 * a suspend()/resume() implementation at all.
+				 * Calling amd74xx_ide_dma_check() without also
+				 * calling amd74xx_tune_drive() hangs my
+				 * nforce3-150 system.  ide-io.c will do just
+				 * that later if we're resuming from s2ram.
+				 */
+				amd_hwifs[i]->tuneproc(drive, 255);
+				amd_hwifs[i]->ide_dma_check(drive);
+			}
+		}
+	}
+
+	return retval;
+}
+
+#endif	/* !CONFIG_PM */
+
 static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
 	amd_chipset = amd74xx_chipsets + id->driver_data;
@@ -539,6 +592,10 @@
 	.name		= "AMD_IDE",
 	.id_table	= amd74xx_pci_tbl,
 	.probe		= amd74xx_probe,
+#ifdef CONFIG_PM
+	.suspend	= amd74xx_suspend,
+	.resume		= amd74xx_resume,
+#endif
 };
 
 static int amd74xx_ide_init(void)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/