Status of HPT372A driver?

[Jonathan McDowell <noodles@earth.li>]

Hi.

I recently acquired a HighPoint RocketRaid 1520 SATA controller (I know,
I know, bad choice but I just need something to tide me over until I can
upgrade to a motherboard with AHCI love). This presents as a HPT372A:

00:09.0 RAID bus controller: Triones Technologies, Inc. HPT372A/372N (rev 01)
00:09.0 0104: 1103:0005 (rev 01)

The 2.6.17 hpt366.c driver is at version 0.36. I also found your patches
to l-k earlier this year, but I'm not sure whether I got them all as I
had some rejects; I ended up with a version 1.00 driver as at:

http://the.earth.li/~noodles/hpt366.c

Is there somewhere I can get your latest work without having to try to
pick the right patches from the l-k archives?

Also I'm getting fairly appalling speeds; I don't know if this is thie
card or not, but I have a SATA II capable drive (I know the controller
 is only SATA I) attached that's getting detected as:

hde: 488397168 sectors (250059 MB) w/16384KiB Cache, CHS=30401/255/63, UDMA(33)

I'd expect UDMA(133) or similar instead? hdparm -Tt gives:

/dev/sda:
 Timing cached reads:   984 MB in  2.00 seconds = 491.58 MB/sec
 Timing buffered disk reads:   90 MB in  3.00 seconds =  30.00 MB/sec

/dev/hda:
 Timing cached reads:   940 MB in  2.00 seconds = 469.89 MB/sec
 Timing buffered disk reads:  172 MB in  3.04 seconds =  56.66 MB/sec

/dev/hde:
 Timing cached reads:   1012 MB in  2.01 seconds = 504.48 MB/sec
 Timing buffered disk reads:   44 MB in  3.05 seconds =  14.43 MB/sec

(sda is an old 36GB SCSI disk on an Adaptec 2940, hda is a Maxtor on the
internal VIA PATA controller. I'd expected hde to at least outperform
sda.)

Relevent dmesg output is:

HPT372A: IDE controller at PCI slot 0000:00:09.0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] - > GSI 11 (level, low) -> IRQ 11
HPT372A: chipset revision 1
HPT372A: DPLL base: 66 MHz, f_CNT: 99, assuming 33 MHz PCI
HPT372A: using 66 MHz DPLL clock
HPT372A: 100%% native mode on irq 11
    ide2: BM-DMA at 0xb000-0xb007, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0xb008-0xb00f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: WDC WD2500KS-00MJB0, ATA DISK drive
ide2 at 0xa000-0xa007,0xa402 on irq 11

J.

-- 
/-\                             | noodles is really a meal in itself
|@/  Debian GNU/Linux Developer |
\-                              |
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/