[PATCH] [2.6.17] Add tsi108 Ethernet device driver support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This patch adds a net device driver and configuration options for
Tundra Semiconductor Tsi108 integrated dual port Gigabit 
Ethernet controller
  
Signed-off-by: Alexandre Bounine <[email protected]>
Signed-off-by: Roy Zang	<[email protected]>
  
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 0c6b45a..360b85f 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2196,6 +2196,14 @@ config SPIDER_NET
 	  This driver supports the Gigabit Ethernet chips present on the
 	  Cell Processor-Based Blades from IBM.
 
+config TSI108_ETH
+	   tristate "Tundra TSI108 gigabit Ethernet support"
+	   depends on TSI108_BRIDGE
+	   help
+	     This driver supports Tundra TSI108 gigabit Ethernet ports.
+	     To compile this driver as a module, choose M here: the module
+	     will be called tsi108_eth.
+
 config GIANFAR
 	tristate "Gianfar Ethernet"
 	depends on 85xx || 83xx
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 1eced32..6bf8186 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -109,6 +109,7 @@ obj-$(CONFIG_B44) += b44.o
 obj-$(CONFIG_FORCEDETH) += forcedeth.o
 obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o
 
+obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
 
 obj-$(CONFIG_PPP) += ppp_generic.o slhc.o
diff --git a/drivers/net/tsi108_eth.c b/drivers/net/tsi108_eth.c
new file mode 100644
index 0000000..77d5a11
--- /dev/null
+++ b/drivers/net/tsi108_eth.c
@@ -0,0 +1,1755 @@
+/*******************************************************************************
+  
+  Copyright(c) 2005 Tundra Semiconductor Corporation.
+  
+  This program is free software; you can redistribute it and/or modify it 
+  under the terms of the GNU General Public License as published by the Free 
+  Software Foundation; either version 2 of the License, or (at your option) 
+  any later version.
+  
+  This program is distributed in the hope that it will be useful, but WITHOUT 
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for 
+  more details.
+  
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc., 59 
+  Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+
+*******************************************************************************/
+
+/* This driver is based on the driver code originally developed	
+ * for the Intel IOC80314 (ForestLake) Gigabit Ethernet by
+ * [email protected]  * Copyright (C) 2003 TimeSys Corporation
+ *
+ * Currently changes from original version are:
+ * - portig to Tsi108-based platform and kernel 2.6 ([email protected])
+ * - modifications to handle two ports independently and support for
+ *   additional PHY devices ([email protected])
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/net.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/device.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <linux/pci.h>
+#include <linux/rtnetlink.h>
+#include <linux/timer.h>
+#include <linux/platform_device.h>
+
+#include <asm/tsi108_irq.h>
+#include <asm/tsi108.h>
+#include "tsi108_eth.h"
+
+#undef DEBUG
+#ifdef DEBUG
+#define DBG(fmt...) do { printk(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+typedef struct net_device net_device;
+typedef struct sk_buff sk_buff;
+
+#define MII_READ_DELAY 10000	/* max link wait time in msec */
+
+#define TSI108_RXRING_LEN     256
+
+/* NOTE: The driver currently does not support receiving packets
+ * larger than the buffer size, so don't decrease this (unless you
+ * want to add such support).
+ */
+#define TSI108_RXBUF_SIZE     1536
+
+#define TSI108_TXRING_LEN     256
+
+#define TSI108_TX_INT_FREQ    64
+
+/* Check the phy status every half a second. */
+#define CHECK_PHY_INTERVAL (HZ/2)
+
+static int tsi108_init_one(struct platform_device *pdev);
+static int tsi108_ether_remove(struct platform_device *pdev);
+
+typedef struct {
+	volatile u32 regs;	/* Base of normal regs */
+	volatile u32 phyregs;	/* Base of register bank used for PHY access */
+	int phy;		/* Index of PHY for this interface */
+	int irq_num;
+
+	struct timer_list timer;/* Timer that triggers the check phy function */
+	int rxtail;		/* Next entry in rxring to read */
+	int rxhead;		/* Next entry in rxring to give a new buffer */
+	int rxfree;		/* Number of free, allocated RX buffers */
+
+	int rxpending;		/* Non-zero if there are still descriptors
+				 * to be processed from a previous descriptor
+				 * interrupt condition that has been cleared */
+
+	int txtail;		/* Next TX descriptor to check status on */
+	int txhead;		/* Next TX descriptor to use */
+
+	/* Number of free TX descriptors.  This could be calculated from
+	 * rxhead and rxtail if one descriptor were left unused to disambiguate
+	 * full and empty conditions, but it's simpler to just keep track
+	 * explicitly. */
+
+	int txfree;
+
+	int phy_ok;		/* The PHY is currently powered on. */
+
+	/* PHY status (duplex is 1 for half, 2 for full,
+	 * so that the default 0 indicates that neither has
+	 * yet been configured). */
+
+	int link_up;
+	int speed;
+	int duplex;
+
+	tx_desc *txring;
+	rx_desc *rxring;
+	sk_buff *txskbs[TSI108_TXRING_LEN];
+	sk_buff *rxskbs[TSI108_RXRING_LEN];
+
+	dma_addr_t txdma, rxdma;
+
+	/* txlock nests in misclock and phy_lock */
+
+	spinlock_t txlock, misclock;
+
+	/* stats is used to hold the upper bits of each hardware counter,
+	 * and tmpstats is used to hold the full values for returning
+	 * to the caller of get_stats().  They must be separate in case
+	 * an overflow interrupt occurs before the stats are consumed.
+	 */
+
+	struct net_device_stats stats;
+	struct net_device_stats tmpstats;
+
+	/* These stats are kept separate in hardware, thus require individual
+	 * fields for handling carry.  They are combined in get_stats.
+	 */
+
+	unsigned long rx_fcs;	/* Add to rx_frame_errors */
+	unsigned long rx_short_fcs;	/* Add to rx_frame_errors */
+	unsigned long rx_long_fcs;	/* Add to rx_frame_errors */
+	unsigned long rx_underruns;	/* Add to rx_length_errors */
+	unsigned long rx_overruns;	/* Add to rx_length_errors */
+
+	unsigned long tx_coll_abort;	/* Add to tx_aborted_errors/collisions */
+	unsigned long tx_pause_drop;	/* Add to tx_aborted_errors */
+
+	unsigned long mc_hash[16];
+} tsi108_prv_data;
+
+/* Structure for a device driver */
+
+static struct platform_driver tsi_eth_driver = {
+	.probe = tsi108_init_one,
+	.remove = tsi108_ether_remove,
+	.driver	= {
+		.name = "tsi-ethernet",
+	},
+};
+
+static void tsi108_timed_checker(unsigned long dev_ptr);
+
+static void dump_eth_one(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	printk("Dumping %s...\n", dev->name);
+	printk("intstat %x intmask %x phy_ok %d"
+	       " link %d speed %d duplex %d\n",
+	       TSI108_ETH_READ_REG(TSI108_EC_INTSTAT),
+	       TSI108_ETH_READ_REG(TSI108_EC_INTMASK), data->phy_ok,
+	       data->link_up, data->speed, data->duplex);
+
+	printk("TX: head %d, tail %d, free %d, stat %x, estat %x, err %x\n",
+	       data->txhead, data->txtail, data->txfree,
+	       TSI108_ETH_READ_REG(TSI108_EC_TXSTAT),
+	       TSI108_ETH_READ_REG(TSI108_EC_TXESTAT),
+	       TSI108_ETH_READ_REG(TSI108_EC_TXERR));
+
+	printk("RX: head %d, tail %d, free %d, stat %x,"
+	       " estat %x, err %x, pending %d\n\n",
+	       data->rxhead, data->rxtail, data->rxfree,
+	       TSI108_ETH_READ_REG(TSI108_EC_RXSTAT),
+	       TSI108_ETH_READ_REG(TSI108_EC_RXESTAT),
+	       TSI108_ETH_READ_REG(TSI108_EC_RXERR), data->rxpending);
+}
+
+/* Synchronization is needed between the thread and up/down events.
+ * Note that the PHY is accessed through the same registers for both
+ * interfaces, so this can't be made interface-specific.
+ */
+
+static spinlock_t phy_lock = SPIN_LOCK_UNLOCKED;
+
+static inline u16 tsi108_read_mii(tsi108_prv_data * data, int reg, int *status)
+{
+	int i;
+	u16 ret;
+
+	TSI108_ETH_WRITE_PHYREG(TSI108_MAC_MII_ADDR,
+				(data->phy << TSI108_MAC_MII_ADDR_PHY) |
+				(reg << TSI108_MAC_MII_ADDR_REG));
+	mb();
+	TSI108_ETH_WRITE_PHYREG(TSI108_MAC_MII_CMD, 0);
+	mb();
+	TSI108_ETH_WRITE_PHYREG(TSI108_MAC_MII_CMD, TSI108_MAC_MII_CMD_READ);
+	mb();
+	for (i = 0; i < 100; i++) {
+		if (!(TSI108_ETH_READ_PHYREG(TSI108_MAC_MII_IND) &
+		      (TSI108_MAC_MII_IND_NOTVALID | TSI108_MAC_MII_IND_BUSY)))
+			break;
+		udelay(10);
+	}
+
+	if (i == 100) {
+		if (status)
+			*status = -EBUSY;
+
+		ret = 0xffff;
+	} else {
+		if (status)
+			*status = 0;
+
+		ret = TSI108_ETH_READ_PHYREG(TSI108_MAC_MII_DATAIN);
+	}
+
+	return ret;
+}
+
+static inline void tsi108_write_mii(tsi108_prv_data * data, int reg, u16 val)
+{
+	TSI108_ETH_WRITE_PHYREG(TSI108_MAC_MII_ADDR,
+				(data->phy << TSI108_MAC_MII_ADDR_PHY) |
+				(reg << TSI108_MAC_MII_ADDR_REG));
+	mb();
+	TSI108_ETH_WRITE_PHYREG(TSI108_MAC_MII_DATAOUT, val);
+	mb();
+	while (TSI108_ETH_READ_PHYREG(TSI108_MAC_MII_IND) &
+	       TSI108_MAC_MII_IND_BUSY) ;
+}
+
+static inline void tsi108_write_tbi(tsi108_prv_data * data, int reg, u16 val)
+{
+
+	TSI108_ETH_WRITE_REG(TSI108_MAC_MII_ADDR,
+			     (0x1e << TSI108_MAC_MII_ADDR_PHY)
+			     | (reg << TSI108_MAC_MII_ADDR_REG));
+	mb();
+
+	TSI108_ETH_WRITE_REG(TSI108_MAC_MII_DATAOUT, val);
+	mb();
+	while (TSI108_ETH_READ_REG(TSI108_MAC_MII_IND) &
+	       TSI108_MAC_MII_IND_BUSY) ;
+}
+
+static void tsi108_check_phy(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u16 sumstat;
+	u32 mac_cfg2_reg, portctrl_reg;
+	u32 fdx_flag = 0, reg_update = 0;
+
+	/* Do a dummy read, as for some reason the first read
+	 * after a link becomes up returns link down, even if
+	 * it's been a while since the link came up.
+	 */
+
+	spin_lock(&phy_lock);
+
+	if (!data->phy_ok)
+		goto out;
+
+	tsi108_read_mii(data, PHY_STAT, NULL);
+
+	if (!(tsi108_read_mii(data, PHY_STAT, NULL) & PHY_STAT_LINKUP)) {
+		if (data->link_up == 1) {
+			netif_stop_queue(dev);
+			data->link_up = 0;
+			printk(KERN_NOTICE "%s : link is down\n", dev->name);
+			netif_carrier_off(dev);
+		}
+
+		goto out;
+	}
+
+	{
+		mac_cfg2_reg = TSI108_ETH_READ_REG(TSI108_MAC_CFG2);
+		portctrl_reg = TSI108_ETH_READ_REG(TSI108_EC_PORTCTRL);
+
+		sumstat = tsi108_read_mii(data, PHY_SUM_STAT, NULL);
+
+		switch (sumstat & PHY_SUM_STAT_SPEED_MASK) {
+		case PHY_SUM_STAT_1000T_FD:
+			fdx_flag++;
+		case PHY_SUM_STAT_1000T_HD:
+			if (data->speed != 1000) {
+				mac_cfg2_reg &= ~TSI108_MAC_CFG2_IFACE_MASK;
+				mac_cfg2_reg |= TSI108_MAC_CFG2_GIG;
+				portctrl_reg &= ~TSI108_EC_PORTCTRL_NOGIG;
+				data->speed = 1000;
+				reg_update++;
+			}
+			break;
+		case PHY_SUM_STAT_100TX_FD:
+			fdx_flag++;
+		case PHY_SUM_STAT_100TX_HD:
+			if (data->speed != 100) {
+				mac_cfg2_reg &= ~TSI108_MAC_CFG2_IFACE_MASK;
+				mac_cfg2_reg |= TSI108_MAC_CFG2_NOGIG;
+				portctrl_reg |= TSI108_EC_PORTCTRL_NOGIG;
+				data->speed = 100;
+				reg_update++;
+			}
+			break;
+
+		case PHY_SUM_STAT_10T_FD:
+			fdx_flag++;
+		case PHY_SUM_STAT_10T_HD:
+			if (data->speed != 10) {
+				mac_cfg2_reg &= ~TSI108_MAC_CFG2_IFACE_MASK;
+				mac_cfg2_reg |= TSI108_MAC_CFG2_NOGIG;
+				portctrl_reg |= TSI108_EC_PORTCTRL_NOGIG;
+				data->speed = 10;
+				reg_update++;
+			}
+			break;
+
+		default:
+			if (net_ratelimit())
+				printk(KERN_ERR "PHY reported invalid speed,"
+				       KERN_ERR " summary status %x\n",
+				       sumstat);
+			goto out;
+		}
+
+		if (fdx_flag || (sumstat & PHY_SUM_STAT_FULLDUPLEX)) {
+			if (data->duplex != 2) {
+				mac_cfg2_reg |= TSI108_MAC_CFG2_FULLDUPLEX;
+				portctrl_reg &= ~TSI108_EC_PORTCTRL_HALFDUPLEX;
+				data->duplex = 2;
+				reg_update++;
+			}
+		} else {
+			if (data->duplex != 1) {
+				mac_cfg2_reg &= ~TSI108_MAC_CFG2_FULLDUPLEX;
+				portctrl_reg |= TSI108_EC_PORTCTRL_HALFDUPLEX;
+				data->duplex = 1;
+				reg_update++;
+			}
+		}
+
+		if (reg_update) {
+			TSI108_ETH_WRITE_REG(TSI108_MAC_CFG2, mac_cfg2_reg);
+			mb();
+			TSI108_ETH_WRITE_REG(TSI108_EC_PORTCTRL, portctrl_reg);
+			mb();
+		}
+
+	}
+
+	if (data->link_up == 0) {
+		/* The manual says it can take 3-4 usecs for the speed change
+		 * to take effect.
+		 */
+		udelay(5);
+
+		spin_lock(&data->txlock);
+		if (netif_queue_stopped(dev)
+		    && is_valid_ether_addr(dev->dev_addr) && data->txfree)
+			netif_wake_queue(dev);
+
+		data->link_up = 1;
+		spin_unlock(&data->txlock);
+		printk("%s : link is up: %dMb %s-duplex\n",
+		       dev->name, data->speed,
+		       (data->duplex == 2) ? "full" : "half");
+		netif_carrier_on(dev);
+	}
+
+      out:
+	spin_unlock(&phy_lock);
+}
+
+static inline void
+tsi108_stat_carry_one(int carry, int carry_bit, int carry_shift,
+		      unsigned long *upper)
+{
+	if (carry & carry_bit)
+		*upper += carry_shift;
+}
+
+static void tsi108_stat_carry(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 carry1, carry2;
+
+	spin_lock_irq(&data->misclock);
+
+	carry1 = TSI108_ETH_READ_REG(TSI108_STAT_CARRY1);
+	carry2 = TSI108_ETH_READ_REG(TSI108_STAT_CARRY2);
+
+	TSI108_ETH_WRITE_REG(TSI108_STAT_CARRY1, carry1);
+	TSI108_ETH_WRITE_REG(TSI108_STAT_CARRY2, carry2);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXBYTES,
+			      TSI108_STAT_RXBYTES_CARRY, &data->stats.rx_bytes);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXPKTS,
+			      TSI108_STAT_RXPKTS_CARRY,
+			      &data->stats.rx_packets);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXFCS,
+			      TSI108_STAT_RXFCS_CARRY, &data->rx_fcs);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXMCAST,
+			      TSI108_STAT_RXMCAST_CARRY,
+			      &data->stats.multicast);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXALIGN,
+			      TSI108_STAT_RXALIGN_CARRY,
+			      &data->stats.rx_frame_errors);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXLENGTH,
+			      TSI108_STAT_RXLENGTH_CARRY,
+			      &data->stats.rx_length_errors);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXRUNT,
+			      TSI108_STAT_RXRUNT_CARRY, &data->rx_underruns);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXJUMBO,
+			      TSI108_STAT_RXJUMBO_CARRY, &data->rx_overruns);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXFRAG,
+			      TSI108_STAT_RXFRAG_CARRY, &data->rx_short_fcs);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXJABBER,
+			      TSI108_STAT_RXJABBER_CARRY, &data->rx_long_fcs);
+
+	tsi108_stat_carry_one(carry1, TSI108_STAT_CARRY1_RXDROP,
+			      TSI108_STAT_RXDROP_CARRY,
+			      &data->stats.rx_missed_errors);
+
+	tsi108_stat_carry_one(carry2, TSI108_STAT_CARRY2_TXBYTES,
+			      TSI108_STAT_TXBYTES_CARRY, &data->stats.tx_bytes);
+
+	tsi108_stat_carry_one(carry2, TSI108_STAT_CARRY2_TXPKTS,
+			      TSI108_STAT_TXPKTS_CARRY,
+			      &data->stats.tx_packets);
+
+	tsi108_stat_carry_one(carry2, TSI108_STAT_CARRY2_TXEXDEF,
+			      TSI108_STAT_TXEXDEF_CARRY,
+			      &data->stats.tx_aborted_errors);
+
+	tsi108_stat_carry_one(carry2, TSI108_STAT_CARRY2_TXEXCOL,
+			      TSI108_STAT_TXEXCOL_CARRY, &data->tx_coll_abort);
+
+	tsi108_stat_carry_one(carry2, TSI108_STAT_CARRY2_TXTCOL,
+			      TSI108_STAT_TXTCOL_CARRY,
+			      &data->stats.collisions);
+
+	tsi108_stat_carry_one(carry2, TSI108_STAT_CARRY2_TXPAUSE,
+			      TSI108_STAT_TXPAUSEDROP_CARRY,
+			      &data->tx_pause_drop);
+
+	spin_unlock_irq(&data->misclock);
+}
+
+/* Read a stat counter atomically with respect to carries.
+ * data->misclock must be held.
+ */
+static inline unsigned long
+tsi108_read_stat(tsi108_prv_data * data, int reg, int carry_bit,
+		 int carry_shift, unsigned long *upper)
+{
+	int carryreg;
+	unsigned long val;
+
+	if (reg < 0xb0)
+		carryreg = TSI108_STAT_CARRY1;
+	else
+		carryreg = TSI108_STAT_CARRY2;
+
+      again:
+	val = TSI108_ETH_READ_REG(reg) | *upper;
+
+	rmb();
+
+	/* Check to see if it overflowed, but the interrupt hasn't
+	 * been serviced yet.  If so, handle the carry here, and
+	 * try again.
+	 */
+
+	if (unlikely(TSI108_ETH_READ_REG(carryreg) & carry_bit)) {
+		*upper += carry_shift;
+		TSI108_ETH_WRITE_REG(carryreg, carry_bit);
+		mb();
+
+		goto again;
+	}
+
+	return val;
+}
+
+static struct net_device_stats *tsi108_get_stats(net_device * dev)
+{
+	unsigned long excol;
+
+	tsi108_prv_data *data = netdev_priv(dev);
+	spin_lock_irq(&data->misclock);
+
+	data->tmpstats.rx_packets =
+	    tsi108_read_stat(data, TSI108_STAT_RXPKTS,
+			     TSI108_STAT_CARRY1_RXPKTS,
+			     TSI108_STAT_RXPKTS_CARRY, &data->stats.rx_packets);
+
+	data->tmpstats.tx_packets =
+	    tsi108_read_stat(data, TSI108_STAT_TXPKTS,
+			     TSI108_STAT_CARRY2_TXPKTS,
+			     TSI108_STAT_TXPKTS_CARRY, &data->stats.tx_packets);
+
+	data->tmpstats.rx_bytes =
+	    tsi108_read_stat(data, TSI108_STAT_RXBYTES,
+			     TSI108_STAT_CARRY1_RXBYTES,
+			     TSI108_STAT_RXBYTES_CARRY, &data->stats.rx_bytes);
+
+	data->tmpstats.tx_bytes =
+	    tsi108_read_stat(data, TSI108_STAT_TXBYTES,
+			     TSI108_STAT_CARRY2_TXBYTES,
+			     TSI108_STAT_TXBYTES_CARRY, &data->stats.tx_bytes);
+
+	data->tmpstats.multicast =
+	    tsi108_read_stat(data, TSI108_STAT_RXMCAST,
+			     TSI108_STAT_CARRY1_RXMCAST,
+			     TSI108_STAT_RXMCAST_CARRY, &data->stats.multicast);
+
+	excol = tsi108_read_stat(data, TSI108_STAT_TXEXCOL,
+				 TSI108_STAT_CARRY2_TXEXCOL,
+				 TSI108_STAT_TXEXCOL_CARRY,
+				 &data->tx_coll_abort);
+
+	data->tmpstats.collisions =
+	    tsi108_read_stat(data, TSI108_STAT_TXTCOL,
+			     TSI108_STAT_CARRY2_TXTCOL,
+			     TSI108_STAT_TXTCOL_CARRY, &data->stats.collisions);
+
+	data->tmpstats.collisions += excol;
+
+	data->tmpstats.rx_length_errors =
+	    tsi108_read_stat(data, TSI108_STAT_RXLENGTH,
+			     TSI108_STAT_CARRY1_RXLENGTH,
+			     TSI108_STAT_RXLENGTH_CARRY,
+			     &data->stats.rx_length_errors);
+
+	data->tmpstats.rx_length_errors +=
+	    tsi108_read_stat(data, TSI108_STAT_RXRUNT,
+			     TSI108_STAT_CARRY1_RXRUNT,
+			     TSI108_STAT_RXRUNT_CARRY, &data->rx_underruns);
+
+	data->tmpstats.rx_length_errors +=
+	    tsi108_read_stat(data, TSI108_STAT_RXJUMBO,
+			     TSI108_STAT_CARRY1_RXJUMBO,
+			     TSI108_STAT_RXJUMBO_CARRY, &data->rx_overruns);
+
+	data->tmpstats.rx_frame_errors =
+	    tsi108_read_stat(data, TSI108_STAT_RXALIGN,
+			     TSI108_STAT_CARRY1_RXALIGN,
+			     TSI108_STAT_RXALIGN_CARRY,
+			     &data->stats.rx_frame_errors);
+
+	data->tmpstats.rx_frame_errors +=
+	    tsi108_read_stat(data, TSI108_STAT_RXFCS,
+			     TSI108_STAT_CARRY1_RXFCS, TSI108_STAT_RXFCS_CARRY,
+			     &data->rx_fcs);
+
+	data->tmpstats.rx_frame_errors +=
+	    tsi108_read_stat(data, TSI108_STAT_RXFRAG,
+			     TSI108_STAT_CARRY1_RXFRAG,
+			     TSI108_STAT_RXFRAG_CARRY, &data->rx_short_fcs);
+
+	data->tmpstats.rx_missed_errors =
+	    tsi108_read_stat(data, TSI108_STAT_RXDROP,
+			     TSI108_STAT_CARRY1_RXDROP,
+			     TSI108_STAT_RXDROP_CARRY,
+			     &data->stats.rx_missed_errors);
+
+	/* These three are maintained by software. */
+	data->tmpstats.rx_fifo_errors = data->stats.rx_fifo_errors;
+	data->tmpstats.rx_crc_errors = data->stats.rx_crc_errors;
+
+	data->tmpstats.tx_aborted_errors =
+	    tsi108_read_stat(data, TSI108_STAT_TXEXDEF,
+			     TSI108_STAT_CARRY2_TXEXDEF,
+			     TSI108_STAT_TXEXDEF_CARRY,
+			     &data->stats.tx_aborted_errors);
+
+	data->tmpstats.tx_aborted_errors +=
+	    tsi108_read_stat(data, TSI108_STAT_TXPAUSEDROP,
+			     TSI108_STAT_CARRY2_TXPAUSE,
+			     TSI108_STAT_TXPAUSEDROP_CARRY,
+			     &data->tx_pause_drop);
+
+	data->tmpstats.tx_aborted_errors += excol;
+
+	data->tmpstats.tx_errors = data->tmpstats.tx_aborted_errors;
+	data->tmpstats.rx_errors = data->tmpstats.rx_length_errors +
+	    data->tmpstats.rx_crc_errors +
+	    data->tmpstats.rx_frame_errors +
+	    data->tmpstats.rx_fifo_errors + data->tmpstats.rx_missed_errors;
+
+	spin_unlock_irq(&data->misclock);
+	return &data->tmpstats;
+}
+
+static void tsi108_restart_rx(tsi108_prv_data * data, net_device * dev)
+{
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXQ_PTRHIGH,
+			     TSI108_EC_RXQ_PTRHIGH_VALID);
+
+	wmb();
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXCTRL, TSI108_EC_RXCTRL_GO
+			     | TSI108_EC_RXCTRL_QUEUE0);
+}
+
+static void tsi108_restart_tx(tsi108_prv_data * data)
+{
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXQ_PTRHIGH,
+			     TSI108_EC_TXQ_PTRHIGH_VALID);
+
+	wmb();
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXCTRL, TSI108_EC_TXCTRL_IDLEINT |
+			     TSI108_EC_TXCTRL_GO | TSI108_EC_TXCTRL_QUEUE0);
+}
+
+/* txlock must be held by caller, with IRQs disabled, and
+ * with permission to re-enable them when the lock is dropped.
+ */
+static void tsi108_check_for_completed_tx(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	int tx;
+	struct sk_buff *skb;
+	int release = 0;
+
+	while (!data->txfree || data->txhead != data->txtail) {
+		tx = data->txtail;
+
+		if (data->txring[tx].misc & TSI108_TX_OWN)
+			break;
+
+		skb = data->txskbs[tx];
+
+		if (!(data->txring[tx].misc & TSI108_TX_OK))
+			printk("%s: bad tx packet, misc %x\n",
+			       dev->name, data->txring[tx].misc);
+
+		data->txtail = (data->txtail + 1) % TSI108_TXRING_LEN;
+		data->txfree++;
+
+		if (data->txring[tx].misc & TSI108_TX_EOF) {
+			dev_kfree_skb_any(skb);
+			release++;
+		}
+	}
+
+	if (release) {
+
+		if (netif_queue_stopped(dev)
+		    && is_valid_ether_addr(dev->dev_addr) && data->link_up)
+			netif_wake_queue(dev);
+	}
+}
+
+static int tsi108_send_packet(sk_buff * skb, net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	int frags = skb_shinfo(skb)->nr_frags + 1;
+	int i;
+#ifdef FIXME_SG_CSUM_NOT_TESTED	/* FIXME: Not supported now. */
+	long csstart;
+	long csum;
+
+	csstart = skb->len - skb->data_len;
+	if (csstart > skb->len - skb->data_len)
+		BUG();
+	csum = 0;
+	if (csstart != skb->len)
+		csum = skb_checksum(skb, csstart, skb->len - csstart, 0);
+#endif
+
+	if (!data->phy_ok && net_ratelimit())
+		printk(KERN_ERR "%s: Transmit while PHY is down!\n", dev->name);
+
+	if (!data->link_up) {
+		printk(KERN_ERR "%s: Transmit while link is down!\n",
+		       dev->name);
+		netif_stop_queue(dev);
+		return 1;
+	}
+
+	if (data->txfree < MAX_SKB_FRAGS + 1) {
+		netif_stop_queue(dev);
+
+		if (net_ratelimit())
+			printk(KERN_ERR "%s: Transmit with full tx ring!\n",
+			       dev->name);
+		return 1;
+	}
+
+	if (data->txfree - frags < MAX_SKB_FRAGS + 1) {
+		netif_stop_queue(dev);
+	}
+
+	spin_lock_irq(&data->txlock);
+
+	for (i = 0; i < frags; i++) {
+		int misc = 0;
+		int tx = data->txhead;
+
+		/* This is done to mark every TSI108_TX_INT_FREQ tx buffers with
+		 * the interrupt bit.  TX descriptor-complete interrupts are
+		 * enabled when the queue fills up, and masked when there is
+		 * still free space.  This way, when saturating the outbound
+		 * link, the tx interrupts are kept to a reasonable level. 
+		 * When the queue is not full, reclamation of skbs still occurs
+		 * as new packets are transmitted, or on a queue-empty
+		 * interrupt.
+		 */
+
+		if ((tx % TSI108_TX_INT_FREQ == 0) &&
+		    ((TSI108_TXRING_LEN - data->txfree) >= TSI108_TX_INT_FREQ)
+		    )
+			misc = TSI108_TX_INT;
+
+		data->txskbs[tx] = skb;
+
+		if (i == 0) {
+			data->txring[tx].buf0 = virt_to_phys(skb->data);
+			data->txring[tx].len = skb->len - skb->data_len;
+			misc |= TSI108_TX_SOF;
+		} else {
+			skb_frag_t *frag = &skb_shinfo(skb)->frags[i - 1];
+
+			data->txring[tx].buf0 =
+			    page_to_phys(frag->page) + frag->page_offset;
+			data->txring[tx].len = frag->size;
+		}
+
+		if (i == frags - 1)
+			misc |= TSI108_TX_EOF;
+
+#ifdef TSI108_PRINT_TX_FRAME
+		{
+			int i;
+			printk("%s: Tx Frame contents (%d)\n", dev->name,
+			       skb->len);
+			for (i = 0; i < skb->len; i++)
+				printk(" %2.2x", skb->data[i]);
+			printk(".\n");
+		}
+#endif				/* TSI108_PRINT_TX_FRAME */
+
+		mb();
+		data->txring[tx].misc = misc | TSI108_TX_OWN;
+
+		data->txhead = (data->txhead + 1) % TSI108_TXRING_LEN;
+		data->txfree--;
+	}
+
+	tsi108_check_for_completed_tx(dev);
+
+	/* This must be done after the check for completed tx descriptors,
+	 * so that the tail pointer is correct.
+	 */
+
+	if (!(TSI108_ETH_READ_REG(TSI108_EC_TXSTAT) & TSI108_EC_TXSTAT_QUEUE0))
+		tsi108_restart_tx(data);
+
+	spin_unlock_irq(&data->txlock);
+	return 0;
+}
+
+static int tsi108_check_for_completed_rx(net_device * dev, int budget)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	int done = 0;
+
+	while (data->rxfree && done != budget) {
+		int rx = data->rxtail;
+		struct sk_buff *skb;
+
+		if (data->rxring[rx].misc & TSI108_RX_OWN)
+			break;
+
+		skb = data->rxskbs[rx];
+		data->rxtail = (data->rxtail + 1) % TSI108_RXRING_LEN;
+		data->rxfree--;
+		done++;
+
+		if (data->rxring[rx].misc & TSI108_RX_BAD) {
+			spin_lock_irq(&data->misclock);
+
+			if (data->rxring[rx].misc & TSI108_RX_CRC)
+				data->stats.rx_crc_errors++;
+			if (data->rxring[rx].misc & TSI108_RX_OVER)
+				data->stats.rx_fifo_errors++;
+
+			spin_unlock_irq(&data->misclock);
+
+			dev_kfree_skb_any(skb);
+			continue;
+		}
+#ifdef TSI108_PRINT_RX_FRAME
+		{
+			int i;
+			printk("%s: Rx Frame contents (%d)\n",
+			       dev->name, data->rxring[rx].len);
+			for (i = 0; i < data->rxring[rx].len; i++)
+				printk(" %2.2x", skb->data[i]);
+			printk(".\n");
+		}
+#endif				/* TSI108_PRINT_RX_FRAME */
+
+		skb->dev = dev;
+		skb_put(skb, data->rxring[rx].len);
+		skb->protocol = eth_type_trans(skb, dev);
+		netif_receive_skb(skb);
+		dev->last_rx = jiffies;
+	}
+
+	return done;
+}
+
+static int tsi108_refill_rx(net_device * dev, int budget)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	int done = 0;
+
+	while (data->rxfree != TSI108_RXRING_LEN && done != budget) {
+		int rx = data->rxhead;
+		sk_buff *skb;
+
+		data->rxskbs[rx] = skb = dev_alloc_skb(TSI108_RXBUF_SIZE + 2);
+		if (!skb)
+			break;
+
+		skb_reserve(skb, 2);	/* Align the data on a 4-byte boundary. */
+
+		data->rxring[rx].buf0 = virt_to_phys(skb->data);
+
+		/* Sometimes the hardware sets blen to zero after packet
+		 * reception, even though the manual says that it's only ever
+		 * modified by the driver.
+		 */
+
+		data->rxring[rx].blen = 1536;
+		mb();
+		data->rxring[rx].misc = TSI108_RX_OWN | TSI108_RX_INT;
+
+		data->rxhead = (data->rxhead + 1) % TSI108_RXRING_LEN;
+		data->rxfree++;
+		done++;
+	}
+
+	mb();
+
+	if (done != 0 && !(TSI108_ETH_READ_REG(TSI108_EC_RXSTAT) &
+			   TSI108_EC_RXSTAT_QUEUE0))
+		tsi108_restart_rx(data, dev);
+
+	return done;
+}
+
+static int tsi108_poll(net_device * dev, int *budget)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 estat = TSI108_ETH_READ_REG(TSI108_EC_RXESTAT);
+	u32 intstat = TSI108_ETH_READ_REG(TSI108_EC_INTSTAT);
+	int total_budget = min(*budget, dev->quota);
+	int num_received = 0, num_filled = 0, budget_used;
+
+	intstat &= TSI108_INT_RXQUEUE0 | TSI108_INT_RXTHRESH |
+	    TSI108_INT_RXOVERRUN | TSI108_INT_RXERROR | TSI108_INT_RXWAIT;
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXESTAT, estat);
+	TSI108_ETH_WRITE_REG(TSI108_EC_INTSTAT, intstat);
+
+	if (data->rxpending || (estat & TSI108_EC_RXESTAT_Q0_DESCINT))
+		num_received = tsi108_check_for_completed_rx(dev, total_budget);
+
+	/* This should normally fill no more slots than the number of
+	 * packets received in tsi108_check_for_completed_rx().  The exception
+	 * is when we previously ran out of memory for RX SKBs.  In that
+	 * case, it's helpful to obey the budget, not only so that the
+	 * CPU isn't hogged, but so that memory (which may still be low)
+	 * is not hogged by one device.
+	 *
+	 * A work unit is considered to be two SKBs to allow us to catch
+	 * up when the ring has shrunk due to out-of-memory but we're
+	 * still removing the full budget's worth of packets each time.
+	 */
+
+	if (data->rxfree < TSI108_RXRING_LEN)
+		num_filled = tsi108_refill_rx(dev, total_budget * 2);
+
+	if (intstat & TSI108_INT_RXERROR) {
+		u32 err = TSI108_ETH_READ_REG(TSI108_EC_RXERR);
+		TSI108_ETH_WRITE_REG(TSI108_EC_RXERR, err);
+
+		if (err) {
+			if (net_ratelimit())
+				printk(KERN_DEBUG "%s: RX error %x\n",
+				       dev->name, err);
+
+			if (!(TSI108_ETH_READ_REG(TSI108_EC_RXSTAT) &
+			      TSI108_EC_RXSTAT_QUEUE0))
+				tsi108_restart_rx(data, dev);
+		}
+	}
+
+	if (intstat & TSI108_INT_RXOVERRUN) {
+		spin_lock_irq(&data->misclock);
+		data->stats.rx_fifo_errors++;
+		spin_unlock_irq(&data->misclock);
+	}
+
+	budget_used = max(num_received, num_filled / 2);
+
+	*budget -= budget_used;
+	dev->quota -= budget_used;
+
+	if (budget_used != total_budget) {
+		data->rxpending = 0;
+		netif_rx_complete(dev);
+
+		TSI108_ETH_WRITE_REG(TSI108_EC_INTMASK,
+				     TSI108_ETH_READ_REG(TSI108_EC_INTMASK)
+				     & ~(TSI108_INT_RXQUEUE0
+					 | TSI108_INT_RXTHRESH |
+					 TSI108_INT_RXOVERRUN |
+					 TSI108_INT_RXERROR |
+					 TSI108_INT_RXWAIT));
+
+		mb();
+
+		/* IRQs are level-triggered, so no need to re-check */
+		return 0;
+	} else {
+		data->rxpending = 1;
+	}
+
+	return 1;
+}
+
+static void tsi108_rx_int(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	/* A race could cause dev to already be scheduled, so it's not an
+	 * error if that happens (and interrupts shouldn't be re-masked,
+	 * because that can cause harmful races, if poll has already
+	 * unmasked them but not cleared LINK_STATE_SCHED).  
+	 *
+	 * This can happen if this code races with tsi108_poll(), which masks
+	 * the interrupts after tsi108_irq_one() read the mask, but before
+	 * netif_rx_schedule is called.  It could also happen due to calls
+	 * from tsi108_check_rxring().
+	 */
+
+	if (netif_rx_schedule_prep(dev)) {
+		/* Mask, rather than ack, the receive interrupts.  The ack
+		 * will happen in tsi108_poll().
+		 */
+
+		TSI108_ETH_WRITE_REG(TSI108_EC_INTMASK,
+				     TSI108_ETH_READ_REG(TSI108_EC_INTMASK) |
+				     TSI108_INT_RXQUEUE0
+				     | TSI108_INT_RXTHRESH |
+				     TSI108_INT_RXOVERRUN | TSI108_INT_RXERROR |
+				     TSI108_INT_RXWAIT);
+		mb();
+		__netif_rx_schedule(dev);
+	} else {
+		if (!netif_running(dev)) {
+			/* This can happen if an interrupt occurs while the
+			 * interface is being brought down, as the START
+			 * bit is cleared before the stop function is called.
+			 *
+			 * In this case, the interrupts must be masked, or
+			 * they will continue indefinitely.
+			 *
+			 * There's a race here if the interface is brought down
+			 * and then up in rapid succession, as the device could
+			 * be made running after the above check and before
+			 * the masking below.  This will only happen if the IRQ
+			 * thread has a lower priority than the task brining
+			 * up the interface.  Fixing this race would likely
+			 * require changes in generic code.
+			 */
+
+			TSI108_ETH_WRITE_REG(TSI108_EC_INTMASK,
+					     TSI108_ETH_READ_REG
+					     (TSI108_EC_INTMASK) |
+					     TSI108_INT_RXQUEUE0 |
+					     TSI108_INT_RXTHRESH |
+					     TSI108_INT_RXOVERRUN |
+					     TSI108_INT_RXERROR |
+					     TSI108_INT_RXWAIT);
+			mb();
+		}
+	}
+}
+
+/* If the RX ring has run out of memory, try periodically
+ * to allocate some more, as otherwise poll would never
+ * get called (apart from the initial end-of-queue condition).
+ *
+ * This is called once per second (by default) from the thread.
+ */
+
+static void tsi108_check_rxring(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	/* A poll is scheduled, as opposed to caling tsi108_refill_rx 
+	 * directly, so as to keep the receive path single-threaded
+	 * (and thus not needing a lock).
+	 */
+
+	if (netif_running(dev) && data->rxfree < TSI108_RXRING_LEN / 4)
+		tsi108_rx_int(dev);
+}
+
+static void tsi108_tx_int(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 estat = TSI108_ETH_READ_REG(TSI108_EC_TXESTAT);
+
+	mb();
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXESTAT, estat);
+	mb();
+	TSI108_ETH_WRITE_REG(TSI108_EC_INTSTAT, TSI108_INT_TXQUEUE0 |
+			     TSI108_INT_TXIDLE | TSI108_INT_TXERROR);
+	mb();
+	if (estat & TSI108_EC_TXESTAT_Q0_ERR) {
+		u32 err = TSI108_ETH_READ_REG(TSI108_EC_TXERR);
+		TSI108_ETH_WRITE_REG(TSI108_EC_TXERR, err);
+
+		if (err && net_ratelimit())
+			printk(KERN_ERR "%s: TX error %x\n", dev->name, err);
+	}
+
+	if (estat & (TSI108_EC_TXESTAT_Q0_DESCINT | TSI108_EC_TXESTAT_Q0_EOQ)) {
+		spin_lock(&data->txlock);
+		tsi108_check_for_completed_tx(dev);
+		spin_unlock(&data->txlock);
+	}
+}
+
+static irqreturn_t tsi108_irq_one(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 stat = TSI108_ETH_READ_REG(TSI108_EC_INTSTAT);
+
+	if (!(stat & TSI108_INT_ANY))
+		return IRQ_NONE;	/* Not our interrupt */
+
+	stat &= ~TSI108_ETH_READ_REG(TSI108_EC_INTMASK);
+
+	if (stat & (TSI108_INT_TXQUEUE0 | TSI108_INT_TXIDLE |
+		    TSI108_INT_TXERROR))
+		tsi108_tx_int(dev);
+	if (stat & (TSI108_INT_RXQUEUE0 | TSI108_INT_RXTHRESH |
+		    TSI108_INT_RXWAIT | TSI108_INT_RXOVERRUN |
+		    TSI108_INT_RXERROR))
+		tsi108_rx_int(dev);
+
+	if (stat & TSI108_INT_SFN) {
+		if (net_ratelimit())
+			printk(KERN_DEBUG "%s: SFN error\n", dev->name);
+		TSI108_ETH_WRITE_REG(TSI108_EC_INTSTAT, TSI108_INT_SFN);
+	}
+
+	if (stat & TSI108_INT_STATCARRY) {
+		tsi108_stat_carry(dev);
+		TSI108_ETH_WRITE_REG(TSI108_EC_INTSTAT, TSI108_INT_STATCARRY);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t tsi108_irq(int irq, void *dev_id, struct pt_regs *regs)
+{
+	if ((IRQ_TSI108_GIGE0 != irq) && (IRQ_TSI108_GIGE1 != irq))
+		return IRQ_NONE;	/* Not our interrupt */
+
+	return tsi108_irq_one((struct net_device *)dev_id);
+}
+
+static void tsi108_stop_ethernet(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	/* Disable all TX and RX queues ... */
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXCTRL, 0);
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXCTRL, 0);
+
+	/* ...and wait for them to become idle */
+	mb();
+	while (TSI108_ETH_READ_REG(TSI108_EC_TXSTAT) &
+	       TSI108_EC_TXSTAT_ACTIVE) ;
+	while (TSI108_ETH_READ_REG(TSI108_EC_RXSTAT) &
+	       TSI108_EC_RXSTAT_ACTIVE) ;
+}
+
+static void tsi108_reset_ether(tsi108_prv_data * data)
+{
+	TSI108_ETH_WRITE_REG(TSI108_MAC_CFG1, TSI108_MAC_CFG1_SOFTRST);
+	udelay(100);
+	TSI108_ETH_WRITE_REG(TSI108_MAC_CFG1, 0);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_PORTCTRL, TSI108_EC_PORTCTRL_STATRST);
+	udelay(100);
+	TSI108_ETH_WRITE_REG(TSI108_EC_PORTCTRL,
+			     TSI108_ETH_READ_REG(TSI108_EC_PORTCTRL) &
+			     ~TSI108_EC_PORTCTRL_STATRST);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXCFG, TSI108_EC_TXCFG_RST);
+	udelay(100);
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXCFG,
+			     TSI108_ETH_READ_REG(TSI108_EC_TXCFG) &
+			     ~TSI108_EC_TXCFG_RST);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXCFG, TSI108_EC_RXCFG_RST);
+	udelay(100);
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXCFG,
+			     TSI108_ETH_READ_REG(TSI108_EC_RXCFG) &
+			     ~TSI108_EC_RXCFG_RST);
+
+	TSI108_ETH_WRITE_REG(TSI108_MAC_MII_MGMT_CFG,
+			     TSI108_ETH_READ_REG(TSI108_MAC_MII_MGMT_CFG) |
+			     TSI108_MAC_MII_MGMT_RST);
+	udelay(100);
+	TSI108_ETH_WRITE_REG(TSI108_MAC_MII_MGMT_CFG,
+			     TSI108_ETH_READ_REG(TSI108_MAC_MII_MGMT_CFG) &
+			     ~(TSI108_MAC_MII_MGMT_RST |
+			       TSI108_MAC_MII_MGMT_CLK));
+
+	TSI108_ETH_WRITE_REG(TSI108_MAC_MII_MGMT_CFG,
+			     TSI108_ETH_READ_REG(TSI108_MAC_MII_MGMT_CFG) |
+			     TSI108_MAC_MII_MGMT_CLK);
+}
+
+static int tsi108_get_mac(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	u32 word1 = TSI108_ETH_READ_REG(TSI108_MAC_ADDR1);
+	u32 word2 = TSI108_ETH_READ_REG(TSI108_MAC_ADDR2);
+
+	/* Note that the octets are reversed from what the manual says,
+	 * producing an even weirder ordering...
+	 */
+	if (word2 == 0 && word1 == 0) {
+		dev->dev_addr[0] = 0x00;
+		dev->dev_addr[1] = 0x06;
+		dev->dev_addr[2] = 0xd2;
+		dev->dev_addr[3] = 0x00;
+		dev->dev_addr[4] = 0x00;
+		if (0x8 == data->phy)
+			dev->dev_addr[5] = 0x01;
+		else
+			dev->dev_addr[5] = 0x02;
+
+		word2 = (dev->dev_addr[0] << 16) | (dev->dev_addr[1] << 24);
+
+		word1 = (dev->dev_addr[2] << 0) | (dev->dev_addr[3] << 8) |
+		    (dev->dev_addr[4] << 16) | (dev->dev_addr[5] << 24);
+
+		TSI108_ETH_WRITE_REG(TSI108_MAC_ADDR1, word1);
+		TSI108_ETH_WRITE_REG(TSI108_MAC_ADDR2, word2);
+	} else {
+		dev->dev_addr[0] = (word2 >> 16) & 0xff;
+		dev->dev_addr[1] = (word2 >> 24) & 0xff;
+		dev->dev_addr[2] = (word1 >> 0) & 0xff;
+		dev->dev_addr[3] = (word1 >> 8) & 0xff;
+		dev->dev_addr[4] = (word1 >> 16) & 0xff;
+		dev->dev_addr[5] = (word1 >> 24) & 0xff;
+	}
+
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		printk("KERN_ERR: word1: %08x, word2: %08x\n", word1, word2);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int tsi108_set_mac(net_device * dev, void *addr)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 word1, word2;
+	int i;
+
+	if (!is_valid_ether_addr(addr))
+		return -EINVAL;
+
+	for (i = 0; i < 6; i++)
+		/* +2 is for the offset of the HW addr type */
+		dev->dev_addr[i] = ((unsigned char *)addr)[i + 2];
+
+	word2 = (dev->dev_addr[0] << 16) | (dev->dev_addr[1] << 24);
+
+	word1 = (dev->dev_addr[2] << 0) | (dev->dev_addr[3] << 8) |
+	    (dev->dev_addr[4] << 16) | (dev->dev_addr[5] << 24);
+
+	spin_lock_irq(&data->misclock);
+	TSI108_ETH_WRITE_REG(TSI108_MAC_ADDR1, word1);
+	TSI108_ETH_WRITE_REG(TSI108_MAC_ADDR2, word2);
+	spin_lock(&data->txlock);
+
+	if (netif_queue_stopped(dev) && data->txfree && data->link_up)
+		netif_wake_queue(dev);
+
+	spin_unlock(&data->txlock);
+	spin_unlock_irq(&data->misclock);
+	return 0;
+}
+
+/* Protected by dev->xmit_lock. */
+static void tsi108_set_rx_mode(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 rxcfg = TSI108_ETH_READ_REG(TSI108_EC_RXCFG);
+
+	if (dev->flags & IFF_PROMISC) {
+		rxcfg &= ~(TSI108_EC_RXCFG_UC_HASH | TSI108_EC_RXCFG_MC_HASH);
+		rxcfg |= TSI108_EC_RXCFG_UFE | TSI108_EC_RXCFG_MFE;
+		goto out;
+	}
+
+	rxcfg &= ~(TSI108_EC_RXCFG_UFE | TSI108_EC_RXCFG_MFE);
+
+	if (dev->mc_count) {
+		int i;
+		struct dev_mc_list *mc = dev->mc_list;
+		rxcfg |= TSI108_EC_RXCFG_MFE | TSI108_EC_RXCFG_MC_HASH;
+
+		memset(data->mc_hash, 0, sizeof(data->mc_hash));
+
+		while (mc) {
+			u32 hash, crc;
+
+			if (mc->dmi_addrlen == 6) {
+				crc = ether_crc(6, mc->dmi_addr);
+				hash = crc >> 23;
+
+				__set_bit(hash, &data->mc_hash[0]);
+			} else {
+				printk(KERN_ERR
+				       "%s: got multicast address of length %d "
+				       "instead of 6.\n", dev->name,
+				       mc->dmi_addrlen);
+			}
+
+			mc = mc->next;
+		}
+
+		TSI108_ETH_WRITE_REG(TSI108_EC_HASHADDR,
+				     TSI108_EC_HASHADDR_AUTOINC |
+				     TSI108_EC_HASHADDR_MCAST);
+
+		for (i = 0; i < 16; i++) {
+			/* The manual says that the hardware may drop
+			 * back-to-back writes to the data register.
+			 */
+			udelay(1);
+			mb();
+			TSI108_ETH_WRITE_REG(TSI108_EC_HASHDATA,
+					     data->mc_hash[i]);
+			mb();
+		}
+	}
+
+      out:
+	mb();
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXCFG, rxcfg);
+}
+
+static void tsi108_init_phy(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	u32 i = 0;
+	u16 phyVal = 0;
+
+	spin_lock_irq(&phy_lock);
+
+	tsi108_write_mii(data, PHY_CTRL, PHY_CTRL_RESET);
+	mb();
+	while (tsi108_read_mii(data, PHY_CTRL, NULL) & PHY_CTRL_RESET) ;
+
+#if (TSI108_PHY_TYPE == PHY_BCM54XX)	/* Broadcom BCM54xx PHY */
+	tsi108_write_mii(data, 0x09, 0x0300);
+	tsi108_write_mii(data, 0x10, 0x1020);
+	tsi108_write_mii(data, 0x1c, 0x8c00);
+	mb();
+#endif
+
+	tsi108_write_mii(data,
+			 PHY_CTRL,
+			 PHY_CTRL_AUTONEG_EN | PHY_CTRL_AUTONEG_START);
+	mb();
+	while (tsi108_read_mii(data, PHY_CTRL, NULL) & PHY_CTRL_AUTONEG_START) ;
+
+	/* Set G/MII mode and receive clock select in TBI control #2.  The
+	 * second port won't work if this isn't done, even though we don't
+	 * use TBI mode.
+	 */
+
+	tsi108_write_tbi(data, 0x11, 0x30);
+
+	/* FIXME: It seems to take more than 2 back-to-back reads to the
+	 * PHY_STAT register before the link up status bit is set.
+	 */
+
+	data->link_up = 1;
+
+	while (!((phyVal = tsi108_read_mii(data, PHY_STAT, NULL)) &
+		 PHY_STAT_LINKUP)) {
+		if (i++ > (MII_READ_DELAY / 10)) {
+			data->link_up = 0;
+			break;
+		}
+		mdelay(10);
+	}
+
+	printk(KERN_DEBUG "PHY_STAT reg contains %08x\n", phyVal);
+	data->phy_ok = 1;
+	spin_unlock_irq(&phy_lock);
+}
+
+static void tsi108_kill_phy(struct net_device *dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	spin_lock_irq(&phy_lock);
+	tsi108_write_mii(data, PHY_CTRL, PHY_CTRL_POWERDOWN);
+	data->phy_ok = 0;
+	spin_unlock_irq(&phy_lock);
+}
+
+static int tsi108_open(struct net_device *dev)
+{
+	int i;
+	tsi108_prv_data *data = netdev_priv(dev);
+	unsigned int rxring_size = TSI108_RXRING_LEN * sizeof(rx_desc);
+	unsigned int txring_size = TSI108_TXRING_LEN * sizeof(tx_desc);
+
+	printk(KERN_DEBUG "Inside tsi108_open()!\n");
+
+	i = request_irq(data->irq_num, tsi108_irq, 0, dev->name, dev);
+	if (i != 0) {
+		printk(KERN_ERR "tsi108_eth%d: Could not allocate IRQ%d.\n",
+		       data->irq_num % IRQ_TSI108_GIGE0, data->irq_num);
+		return i;
+	} else {
+		dev->irq = data->irq_num;
+		printk(KERN_NOTICE
+		       "tsi108_open : Port %d Assigned IRQ %d to %s\n",
+		       data->irq_num % IRQ_TSI108_GIGE0, dev->irq, dev->name);
+	}
+
+	data->rxring = pci_alloc_consistent(NULL, rxring_size, &data->rxdma);
+
+	if (!data->rxring) {
+		printk(KERN_DEBUG
+		       "TSI108_ETH: failed to allocate memory for rxring!\n");
+		return -ENOMEM;
+	} else {
+		memset(data->rxring, 0, rxring_size);
+	}
+
+	data->txring = pci_alloc_consistent(NULL, txring_size, &data->txdma);
+
+	if (!data->txring) {
+		printk(KERN_DEBUG
+		       "TSI108_ETH: failed to allocate memory for txring!\n");
+		pci_free_consistent(0, rxring_size, data->rxring, data->rxdma);
+		return -ENOMEM;
+	} else {
+		memset(data->txring, 0, txring_size);
+	}
+
+	for (i = 0; i < TSI108_RXRING_LEN; i++) {
+		data->rxring[i].next0 = data->rxdma + (i + 1) * sizeof(rx_desc);
+		data->rxring[i].blen = TSI108_RXBUF_SIZE;
+		data->rxring[i].vlan = 0;
+	}
+
+	data->rxring[TSI108_RXRING_LEN - 1].next0 = data->rxdma;
+
+	data->rxtail = 0;
+	data->rxhead = 0;
+
+	for (i = 0; i < TSI108_RXRING_LEN; i++) {
+		sk_buff *skb = dev_alloc_skb(TSI108_RXBUF_SIZE + NET_IP_ALIGN);
+
+		if (!skb) {
+			/* Bah.  No memory for now, but maybe we'll get
+			 * some more later.
+			 * For now, we'll live with the smaller ring.
+			 */
+			printk(KERN_WARNING
+			       "%s: Could only allocate %d receive skb(s).\n",
+			       dev->name, i);
+			data->rxhead = i;
+			break;
+		}
+
+		data->rxskbs[i] = skb;
+		/* Align the payload on a 4-byte boundary */
+		skb_reserve(skb, 2);
+		data->rxskbs[i] = skb;
+		data->rxring[i].buf0 = virt_to_phys(data->rxskbs[i]->data);
+		data->rxring[i].misc = TSI108_RX_OWN | TSI108_RX_INT;
+	}
+
+	data->rxfree = i;
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXQ_PTRLOW, data->rxdma);
+
+	for (i = 0; i < TSI108_TXRING_LEN; i++) {
+		data->txring[i].next0 = data->txdma + (i + 1) * sizeof(tx_desc);
+		data->txring[i].misc = 0;
+	}
+
+	data->txring[TSI108_TXRING_LEN - 1].next0 = data->txdma;
+	data->txtail = 0;
+	data->txhead = 0;
+	data->txfree = TSI108_TXRING_LEN;
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXQ_PTRLOW, data->txdma);
+	tsi108_init_phy(dev);
+
+	init_timer(&data->timer);
+	data->timer.expires = jiffies + 1;
+	data->timer.data = (unsigned long)dev;
+	data->timer.function = &tsi108_timed_checker;	/* timer handler */
+	add_timer(&data->timer);
+
+	tsi108_restart_rx(data, dev);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_INTSTAT, ~0);
+	mb();
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_INTMASK,
+			     ~(TSI108_INT_TXQUEUE0 | TSI108_INT_RXERROR |
+			       TSI108_INT_RXTHRESH | TSI108_INT_RXQUEUE0 |
+			       TSI108_INT_RXOVERRUN | TSI108_INT_RXWAIT |
+			       TSI108_INT_SFN | TSI108_INT_STATCARRY));
+
+	TSI108_ETH_WRITE_REG(TSI108_MAC_CFG1,
+			     TSI108_MAC_CFG1_RXEN | TSI108_MAC_CFG1_TXEN);
+	netif_start_queue(dev);
+	return 0;
+}
+
+static int tsi108_close(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	netif_stop_queue(dev);
+
+	del_timer_sync(&data->timer);
+
+	printk(KERN_DEBUG "Inside tsi108_ifdown!\n");
+
+	tsi108_stop_ethernet(dev);
+	tsi108_kill_phy(dev);
+	TSI108_ETH_WRITE_REG(TSI108_EC_INTMASK, ~0);
+	TSI108_ETH_WRITE_REG(TSI108_MAC_CFG1, 0);
+
+	/* Check for any pending TX packets, and drop them. */
+
+	while (!data->txfree || data->txhead != data->txtail) {
+		int tx = data->txtail;
+		struct sk_buff *skb;
+		skb = data->txskbs[tx];
+		data->txtail = (data->txtail + 1) % TSI108_TXRING_LEN;
+		data->txfree++;
+		dev_kfree_skb(skb);
+	}
+
+	synchronize_irq(data->irq_num);
+	free_irq(data->irq_num, dev);
+
+	/* Discard the RX ring. */
+
+	while (data->rxfree) {
+		int rx = data->rxtail;
+		struct sk_buff *skb;
+
+		skb = data->rxskbs[rx];
+		data->rxtail = (data->rxtail + 1) % TSI108_RXRING_LEN;
+		data->rxfree--;
+		dev_kfree_skb(skb);
+	}
+
+	pci_free_consistent(0,
+			    TSI108_RXRING_LEN * sizeof(rx_desc),
+			    data->rxring, data->rxdma);
+	pci_free_consistent(0,
+			    TSI108_TXRING_LEN * sizeof(tx_desc),
+			    data->txring, data->txdma);
+
+	return 0;
+}
+
+static void tsi108_init_mac(net_device * dev)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	TSI108_ETH_WRITE_REG(TSI108_MAC_CFG2, TSI108_MAC_CFG2_DFLT_PREAMBLE |
+			     TSI108_MAC_CFG2_PADCRC);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXTHRESH,
+			     (192 << TSI108_EC_TXTHRESH_STARTFILL) |
+			     (192 << TSI108_EC_TXTHRESH_STOPFILL));
+
+	TSI108_ETH_WRITE_REG(TSI108_STAT_CARRYMASK1,
+			     ~(TSI108_STAT_CARRY1_RXBYTES |
+			       TSI108_STAT_CARRY1_RXPKTS |
+			       TSI108_STAT_CARRY1_RXFCS |
+			       TSI108_STAT_CARRY1_RXMCAST |
+			       TSI108_STAT_CARRY1_RXALIGN |
+			       TSI108_STAT_CARRY1_RXLENGTH |
+			       TSI108_STAT_CARRY1_RXRUNT |
+			       TSI108_STAT_CARRY1_RXJUMBO |
+			       TSI108_STAT_CARRY1_RXFRAG |
+			       TSI108_STAT_CARRY1_RXJABBER |
+			       TSI108_STAT_CARRY1_RXDROP));
+
+	TSI108_ETH_WRITE_REG(TSI108_STAT_CARRYMASK2,
+			     ~(TSI108_STAT_CARRY2_TXBYTES |
+			       TSI108_STAT_CARRY2_TXPKTS |
+			       TSI108_STAT_CARRY2_TXEXDEF |
+			       TSI108_STAT_CARRY2_TXEXCOL |
+			       TSI108_STAT_CARRY2_TXTCOL |
+			       TSI108_STAT_CARRY2_TXPAUSE));
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_PORTCTRL, TSI108_EC_PORTCTRL_STATEN);
+	TSI108_ETH_WRITE_REG(TSI108_MAC_CFG1, 0);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXCFG,
+			     TSI108_EC_RXCFG_SE | TSI108_EC_RXCFG_BFE);
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXQ_CFG, TSI108_EC_TXQ_CFG_DESC_INT |
+			     TSI108_EC_TXQ_CFG_EOQ_OWN_INT |
+			     TSI108_EC_TXQ_CFG_WSWP | (TSI108_PBM_PORT <<
+						       TSI108_EC_TXQ_CFG_SFNPORT));
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXQ_CFG, TSI108_EC_RXQ_CFG_DESC_INT |
+			     TSI108_EC_RXQ_CFG_EOQ_OWN_INT |
+			     TSI108_EC_RXQ_CFG_WSWP | (TSI108_PBM_PORT <<
+						       TSI108_EC_RXQ_CFG_SFNPORT));
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_TXQ_BUFCFG,
+			     TSI108_EC_TXQ_BUFCFG_BURST256 |
+			     TSI108_EC_TXQ_BUFCFG_BSWP | (TSI108_PBM_PORT <<
+							  TSI108_EC_TXQ_BUFCFG_SFNPORT));
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_RXQ_BUFCFG,
+			     TSI108_EC_RXQ_BUFCFG_BURST256 |
+			     TSI108_EC_RXQ_BUFCFG_BSWP | (TSI108_PBM_PORT <<
+							  TSI108_EC_RXQ_BUFCFG_SFNPORT));
+
+	TSI108_ETH_WRITE_REG(TSI108_EC_INTMASK, ~0);
+}
+
+static int tsi108_ioctl(net_device * dev, struct ifreq *rq, int cmd)
+{
+	tsi108_prv_data *data = netdev_priv(dev);
+	struct mii_ioctl_data *mii_data =
+	    (struct mii_ioctl_data *)&rq->ifr_data;
+	int ret;
+
+	switch (cmd) {
+	case SIOCGMIIPHY:
+		mii_data->phy_id = data->phy;
+		ret = 0;
+		break;
+
+	case SIOCGMIIREG:
+		spin_lock_irq(&phy_lock);
+		mii_data->val_out =
+		    tsi108_read_mii(data, mii_data->reg_num, &ret);
+		spin_unlock_irq(&phy_lock);
+		break;
+
+	default:
+		ret = -EOPNOTSUPP;
+	}
+
+	return ret;
+}
+
+static int
+tsi108_init_one(struct platform_device *pdev)
+{
+	struct net_device *dev = NULL;
+	tsi108_prv_data *data = NULL;
+	hw_info *einfo;
+	int ret;
+	
+	einfo = ( hw_info *) pdev->dev.platform_data;
+	
+	if (NULL == einfo) {
+		printk(KERN_ERR "tsi-eth %d: Missing additional data!\n",
+		       pdev->id);
+		return -ENODEV;
+	}
+
+	/* Create an ethernet device instance */
+
+	dev = alloc_etherdev(sizeof(tsi108_prv_data));
+	if (!dev) {
+		printk("tsi108_eth: Could not allocate a device structure\n");
+		return -ENOMEM;
+	}
+
+	printk("tsi108_eth%d: probe...\n", pdev->id);
+	data = netdev_priv(dev);
+	memset(data, 0, sizeof(tsi108_prv_data));
+
+	DBG("tsi108_eth%d: regs:phyresgs:phy:irq_num=0x%x:0x%x:0x%x:0x%x\n",
+			pdev->id, einfo->regs, einfo->phyregs,
+			einfo->phy, einfo->irq_num);
+
+	data->regs = (u32)ioremap(einfo->regs, 0x400);	/*FIX ME */
+	data->phyregs = (u32)ioremap(einfo->phyregs, 0x400); 	/*FIX ME */
+	data->phy = einfo->phy;
+	data->irq_num = einfo->irq_num;
+	dev->open = tsi108_open;
+	dev->stop = tsi108_close;
+	dev->hard_start_xmit = tsi108_send_packet;
+	dev->set_mac_address = tsi108_set_mac;
+	dev->set_multicast_list = tsi108_set_rx_mode;
+	dev->get_stats = tsi108_get_stats;
+	dev->poll = tsi108_poll;
+	dev->do_ioctl = tsi108_ioctl;
+	dev->weight = 64;	/* 64 is more suitable for GigE interface - klai */
+
+	/* Apparently, the Linux networking code won't use scatter-gather
+	 * if the hardware doesn't do checksums.  However, it's faster
+	 * to checksum in place and use SG, as (among other reasons)
+	 * the cache won't be dirtied (which then has to be flushed
+	 * before DMA).  The checksumming is done by the driver (via
+	 * a new function skb_csum_dev() in net/core/skbuff.c).
+	 */
+
+#ifdef FIXME_SG_CSUM_NOT_TESTED	/* FIXME: Not supported now. */
+	dev->features = NETIF_F_HIGHDMA | NETIF_F_SG | NETIF_F_HW_CSUM;
+#else
+	dev->features = NETIF_F_HIGHDMA;
+#endif
+	SET_MODULE_OWNER(dev);
+
+	spin_lock_init(&data->txlock);
+	spin_lock_init(&data->misclock);
+
+	tsi108_reset_ether(data);
+	tsi108_kill_phy(dev);
+
+	if (tsi108_get_mac(dev) != 0)
+		printk(KERN_ERR "%s: Invalid MAC address.  Please correct.\n",
+		       dev->name);
+
+	tsi108_init_mac(dev);
+	ret = register_netdev(dev);
+	if (ret < 0) {
+		kfree(dev);
+		return ret;
+	}
+
+	printk(KERN_INFO "%s: Tsi108 Gigabit Ethernet, MAC: "
+	       "%02x:%02x:%02x:%02x:%02x:%02x\n", dev->name,
+	       dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
+	       dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
+#ifdef DEBUG
+	dump_eth_one(dev);
+#endif
+
+	return 0;
+}
+
+/* There's no way to either get interrupts from the PHY when
+ * something changes, or to have the Tsi108 automatically communicate
+ * with the PHY to reconfigure itself.
+ *
+ * Thus, we have to do it using a timer. 
+ */
+
+static void tsi108_timed_checker(unsigned long dev_ptr)
+{
+	struct net_device *dev = (struct net_device *)dev_ptr;
+	tsi108_prv_data *data = netdev_priv(dev);
+
+	tsi108_check_phy(dev);
+	tsi108_check_rxring(dev);
+	data->timer.expires = jiffies + CHECK_PHY_INTERVAL;
+	add_timer(&data->timer);
+}
+
+static int tsi108_ether_init(void)
+{
+	int ret;
+	ret = platform_driver_register (&tsi_eth_driver);
+	if (ret < 0){
+		printk("tsi108_ether_init: error initializing ethernet "
+		       "device\n");
+		return ret;
+	}
+	return 0;
+}
+
+static int tsi108_ether_remove(struct platform_device *pdev)
+{
+	struct net_device *dev = platform_get_drvdata(pdev);
+	tsi108_prv_data *priv = netdev_priv(dev);
+	
+	unregister_netdev(dev);
+	tsi108_stop_ethernet(dev);
+	platform_set_drvdata(pdev, NULL);
+	iounmap((void __iomem *)priv->regs);
+	iounmap((void __iomem *)priv->phyregs);
+	free_netdev(dev);
+	
+	return 0;
+}
+static void tsi108_ether_exit(void)
+{
+	platform_driver_unregister(&tsi_eth_driver);
+}
+
+module_init(tsi108_ether_init);
+module_exit(tsi108_ether_exit);
+
+MODULE_AUTHOR("Tundra Semiconductor Corporation");
+MODULE_DESCRIPTION("Tsi108 Gigabit Ethernet driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/tsi108_eth.h b/drivers/net/tsi108_eth.h
new file mode 100644
index 0000000..e491056
--- /dev/null
+++ b/drivers/net/tsi108_eth.h
@@ -0,0 +1,401 @@
+/*
+ * (C) Copyright 2005 Tundra Semiconductor Corp.
+ * Kong Lai, <[email protected]).
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * net/tsi108_eth.h - definitions for Tsi108 GIGE network controller.
+ */
+
+#ifndef __TSI108_ETH_H
+#define __TSI108_ETH_H
+
+#include <linux/config.h>
+#include <linux/types.h>
+
+#define TSI108_ETH_WRITE_REG(offset, val) \
+	out_be32((volatile u32 *)(data->regs + offset), val)
+
+#define TSI108_ETH_READ_REG(offset) \
+	in_be32((volatile u32 *)(data->regs + offset))
+
+#define TSI108_ETH_WRITE_PHYREG(offset, val) \
+	out_be32((volatile u32 *)(data->phyregs + offset), val)
+
+#define TSI108_ETH_READ_PHYREG(offset) \
+	in_be32((volatile u32 *)(data->phyregs + offset))
+
+/*
+ * PHY Configuration Options
+ *
+ * NOTE: Enable set of definitions corresponding to your board type
+ */
+#define PHY_MV88E	1	/* Marvel 88Exxxx PHY */
+#define PHY_BCM54XX	2	/* Broardcom BCM54xx PHY */
+#define TSI108_PHY_TYPE	PHY_MV88E
+
+/*
+ * TSI108 GIGE port registers
+ */
+
+#define TSI108_ETH_PORT_NUM		2
+#define TSI108_PBM_PORT			2
+#define TSI108_SDRAM_PORT		4
+
+#define TSI108_MAC_CFG1			(0x000)
+#define TSI108_MAC_CFG1_SOFTRST		(1 << 31)
+#define TSI108_MAC_CFG1_LOOPBACK	(1 << 8)
+#define TSI108_MAC_CFG1_RXEN		(1 << 2)
+#define TSI108_MAC_CFG1_TXEN		(1 << 0)
+
+#define TSI108_MAC_CFG2			(0x004)
+#define TSI108_MAC_CFG2_DFLT_PREAMBLE	(7 << 12)
+#define TSI108_MAC_CFG2_IFACE_MASK	(3 << 8)
+#define TSI108_MAC_CFG2_NOGIG		(1 << 8)
+#define TSI108_MAC_CFG2_GIG		(2 << 8)
+#define TSI108_MAC_CFG2_PADCRC		(1 << 2)
+#define TSI108_MAC_CFG2_FULLDUPLEX	(1 << 0)
+
+#define TSI108_MAC_MII_MGMT_CFG		(0x020)
+#define TSI108_MAC_MII_MGMT_CLK		(7 << 0)
+#define TSI108_MAC_MII_MGMT_RST		(1 << 31)
+
+#define TSI108_MAC_MII_CMD		(0x024)
+#define TSI108_MAC_MII_CMD_READ		(1 << 0)
+
+#define TSI108_MAC_MII_ADDR		(0x028)
+#define TSI108_MAC_MII_ADDR_REG		0
+#define TSI108_MAC_MII_ADDR_PHY		8
+
+#define TSI108_MAC_MII_DATAOUT		(0x02c)
+#define TSI108_MAC_MII_DATAIN		(0x030)
+
+#define TSI108_MAC_MII_IND		(0x034)
+#define TSI108_MAC_MII_IND_NOTVALID	(1 << 2)
+#define TSI108_MAC_MII_IND_SCANNING	(1 << 1)
+#define TSI108_MAC_MII_IND_BUSY		(1 << 0)
+
+#define TSI108_MAC_IFCTRL		(0x038)
+#define TSI108_MAC_IFCTRL_PHYMODE	(1 << 24)
+
+#define TSI108_MAC_ADDR1		(0x040)
+#define TSI108_MAC_ADDR2		(0x044)
+
+#define TSI108_STAT_RXBYTES		(0x06c)
+#define TSI108_STAT_RXBYTES_CARRY	(1 << 24)
+
+#define TSI108_STAT_RXPKTS		(0x070)
+#define TSI108_STAT_RXPKTS_CARRY	(1 << 18)
+
+#define TSI108_STAT_RXFCS		(0x074)
+#define TSI108_STAT_RXFCS_CARRY		(1 << 12)
+
+#define TSI108_STAT_RXMCAST		(0x078)
+#define TSI108_STAT_RXMCAST_CARRY	(1 << 18)
+
+#define TSI108_STAT_RXALIGN		(0x08c)
+#define TSI108_STAT_RXALIGN_CARRY	(1 << 12)
+
+#define TSI108_STAT_RXLENGTH		(0x090)
+#define TSI108_STAT_RXLENGTH_CARRY	(1 << 12)
+
+#define TSI108_STAT_RXRUNT		(0x09c)
+#define TSI108_STAT_RXRUNT_CARRY	(1 << 12)
+
+#define TSI108_STAT_RXJUMBO		(0x0a0)
+#define TSI108_STAT_RXJUMBO_CARRY	(1 << 12)
+
+#define TSI108_STAT_RXFRAG		(0x0a4)
+#define TSI108_STAT_RXFRAG_CARRY	(1 << 12)
+
+#define TSI108_STAT_RXJABBER		(0x0a8)
+#define TSI108_STAT_RXJABBER_CARRY	(1 << 12)
+
+#define TSI108_STAT_RXDROP		(0x0ac)
+#define TSI108_STAT_RXDROP_CARRY	(1 << 12)
+
+#define TSI108_STAT_TXBYTES		(0x0b0)
+#define TSI108_STAT_TXBYTES_CARRY	(1 << 24)
+
+#define TSI108_STAT_TXPKTS		(0x0b4)
+#define TSI108_STAT_TXPKTS_CARRY	(1 << 18)
+
+#define TSI108_STAT_TXEXDEF		(0x0c8)
+#define TSI108_STAT_TXEXDEF_CARRY	(1 << 12)
+
+#define TSI108_STAT_TXEXCOL		(0x0d8)
+#define TSI108_STAT_TXEXCOL_CARRY	(1 << 12)
+
+#define TSI108_STAT_TXTCOL		(0x0dc)
+#define TSI108_STAT_TXTCOL_CARRY	(1 << 13)
+
+#define TSI108_STAT_TXPAUSEDROP		(0x0e4)
+#define TSI108_STAT_TXPAUSEDROP_CARRY	(1 << 12)
+
+#define TSI108_STAT_CARRY1		(0x100)
+#define TSI108_STAT_CARRY1_RXBYTES	(1 << 16)
+#define TSI108_STAT_CARRY1_RXPKTS	(1 << 15)
+#define TSI108_STAT_CARRY1_RXFCS	(1 << 14)
+#define TSI108_STAT_CARRY1_RXMCAST	(1 << 13)
+#define TSI108_STAT_CARRY1_RXALIGN	(1 << 8)
+#define TSI108_STAT_CARRY1_RXLENGTH	(1 << 7)
+#define TSI108_STAT_CARRY1_RXRUNT	(1 << 4)
+#define TSI108_STAT_CARRY1_RXJUMBO	(1 << 3)
+#define TSI108_STAT_CARRY1_RXFRAG	(1 << 2)
+#define TSI108_STAT_CARRY1_RXJABBER	(1 << 1)
+#define TSI108_STAT_CARRY1_RXDROP	(1 << 0)
+
+#define TSI108_STAT_CARRY2		(0x104)
+#define TSI108_STAT_CARRY2_TXBYTES	(1 << 13)
+#define TSI108_STAT_CARRY2_TXPKTS	(1 << 12)
+#define TSI108_STAT_CARRY2_TXEXDEF	(1 << 7)
+#define TSI108_STAT_CARRY2_TXEXCOL	(1 << 3)
+#define TSI108_STAT_CARRY2_TXTCOL	(1 << 2)
+#define TSI108_STAT_CARRY2_TXPAUSE	(1 << 0)
+
+#define TSI108_STAT_CARRYMASK1		(0x108)
+#define TSI108_STAT_CARRYMASK2		(0x10c)
+
+#define TSI108_EC_PORTCTRL		(0x200)
+#define TSI108_EC_PORTCTRL_STATRST	(1 << 31)
+#define TSI108_EC_PORTCTRL_STATEN	(1 << 28)
+#define TSI108_EC_PORTCTRL_NOGIG	(1 << 18)
+#define TSI108_EC_PORTCTRL_HALFDUPLEX	(1 << 16)
+
+#define TSI108_EC_INTSTAT		(0x204)
+#define TSI108_EC_INTMASK		(0x208)
+
+#define TSI108_INT_ANY			(1 << 31)
+#define TSI108_INT_SFN			(1 << 30)
+#define TSI108_INT_RXIDLE		(1 << 29)
+#define TSI108_INT_RXABORT		(1 << 28)
+#define TSI108_INT_RXERROR		(1 << 27)
+#define TSI108_INT_RXOVERRUN		(1 << 26)
+#define TSI108_INT_RXTHRESH		(1 << 25)
+#define TSI108_INT_RXWAIT		(1 << 24)
+#define TSI108_INT_RXQUEUE0		(1 << 16)
+#define TSI108_INT_STATCARRY		(1 << 15)
+#define TSI108_INT_TXIDLE		(1 << 13)
+#define TSI108_INT_TXABORT		(1 << 12)
+#define TSI108_INT_TXERROR		(1 << 11)
+#define TSI108_INT_TXUNDERRUN		(1 << 10)
+#define TSI108_INT_TXTHRESH		(1 <<  9)
+#define TSI108_INT_TXWAIT		(1 <<  8)
+#define TSI108_INT_TXQUEUE0		(1 <<  0)
+
+#define TSI108_EC_TXCFG			(0x220)
+#define TSI108_EC_TXCFG_RST		(1 << 31)
+
+#define TSI108_EC_TXCTRL		(0x224)
+#define TSI108_EC_TXCTRL_IDLEINT	(1 << 31)
+#define TSI108_EC_TXCTRL_ABORT		(1 << 30)
+#define TSI108_EC_TXCTRL_GO		(1 << 15)
+#define TSI108_EC_TXCTRL_QUEUE0		(1 <<  0)
+
+#define TSI108_EC_TXSTAT		(0x228)
+#define TSI108_EC_TXSTAT_ACTIVE		(1 << 15)
+#define TSI108_EC_TXSTAT_QUEUE0		(1 << 0)
+
+#define TSI108_EC_TXESTAT		(0x22c)
+#define TSI108_EC_TXESTAT_Q0_ERR	(1 << 24)
+#define TSI108_EC_TXESTAT_Q0_DESCINT	(1 << 16)
+#define TSI108_EC_TXESTAT_Q0_EOF	(1 <<  8)
+#define TSI108_EC_TXESTAT_Q0_EOQ	(1 <<  0)
+
+#define TSI108_EC_TXERR			(0x278)
+
+#define TSI108_EC_TXQ_CFG		(0x280)
+#define TSI108_EC_TXQ_CFG_DESC_INT	(1 << 20)
+#define TSI108_EC_TXQ_CFG_EOQ_OWN_INT	(1 << 19)
+#define TSI108_EC_TXQ_CFG_WSWP		(1 << 11)
+#define TSI108_EC_TXQ_CFG_BSWP		(1 << 10)
+#define TSI108_EC_TXQ_CFG_SFNPORT	0
+
+#define TSI108_EC_TXQ_BUFCFG		(0x284)
+#define TSI108_EC_TXQ_BUFCFG_BURST8	(0 << 8)
+#define TSI108_EC_TXQ_BUFCFG_BURST32	(1 << 8)
+#define TSI108_EC_TXQ_BUFCFG_BURST128	(2 << 8)
+#define TSI108_EC_TXQ_BUFCFG_BURST256	(3 << 8)
+#define TSI108_EC_TXQ_BUFCFG_WSWP	(1 << 11)
+#define TSI108_EC_TXQ_BUFCFG_BSWP	(1 << 10)
+#define TSI108_EC_TXQ_BUFCFG_SFNPORT	0
+
+#define TSI108_EC_TXQ_PTRLOW		(0x288)
+
+#define TSI108_EC_TXQ_PTRHIGH		(0x28c)
+#define TSI108_EC_TXQ_PTRHIGH_VALID	(1 << 31)
+
+#define TSI108_EC_TXTHRESH		(0x230)
+#define TSI108_EC_TXTHRESH_STARTFILL	0
+#define TSI108_EC_TXTHRESH_STOPFILL	16
+
+#define TSI108_EC_RXCFG			(0x320)
+#define TSI108_EC_RXCFG_RST		(1 << 31)
+
+#define TSI108_EC_RXSTAT		(0x328)
+#define TSI108_EC_RXSTAT_ACTIVE		(1 << 15)
+#define TSI108_EC_RXSTAT_QUEUE0		(1 << 0)
+
+#define TSI108_EC_RXESTAT		(0x32c)
+#define TSI108_EC_RXESTAT_Q0_ERR	(1 << 24)
+#define TSI108_EC_RXESTAT_Q0_DESCINT	(1 << 16)
+#define TSI108_EC_RXESTAT_Q0_EOF	(1 <<  8)
+#define TSI108_EC_RXESTAT_Q0_EOQ	(1 <<  0)
+
+#define TSI108_EC_HASHADDR		(0x360)
+#define TSI108_EC_HASHADDR_AUTOINC	(1 << 31)
+#define TSI108_EC_HASHADDR_DO1STREAD	(1 << 30)
+#define TSI108_EC_HASHADDR_UNICAST	(0 <<  4)
+#define TSI108_EC_HASHADDR_MCAST	(1 <<  4)
+
+#define TSI108_EC_HASHDATA		(0x364)
+
+#define TSI108_EC_RXQ_PTRLOW		(0x388)
+
+#define TSI108_EC_RXQ_PTRHIGH		(0x38c)
+#define TSI108_EC_RXQ_PTRHIGH_VALID	(1 << 31)
+
+/* Station Enable -- accept packets destined for us */
+#define TSI108_EC_RXCFG_SE		(1 << 13)
+/* Unicast Frame Enable -- for packets not destined for us */
+#define TSI108_EC_RXCFG_UFE		(1 << 12)
+/* Multicast Frame Enable */
+#define TSI108_EC_RXCFG_MFE		(1 << 11)
+/* Broadcast Frame Enable */
+#define TSI108_EC_RXCFG_BFE		(1 << 10)
+#define TSI108_EC_RXCFG_UC_HASH		(1 <<  9)
+#define TSI108_EC_RXCFG_MC_HASH		(1 <<  8)
+
+#define TSI108_EC_RXQ_CFG		(0x380)
+#define TSI108_EC_RXQ_CFG_DESC_INT	(1 << 20)
+#define TSI108_EC_RXQ_CFG_EOQ_OWN_INT	(1 << 19)
+#define TSI108_EC_RXQ_CFG_WSWP		(1 << 11)
+#define TSI108_EC_RXQ_CFG_BSWP		(1 << 10)
+#define TSI108_EC_RXQ_CFG_SFNPORT	0
+
+#define TSI108_EC_RXQ_BUFCFG		(0x384)
+#define TSI108_EC_RXQ_BUFCFG_BURST8	(0 << 8)
+#define TSI108_EC_RXQ_BUFCFG_BURST32	(1 << 8)
+#define TSI108_EC_RXQ_BUFCFG_BURST128	(2 << 8)
+#define TSI108_EC_RXQ_BUFCFG_BURST256	(3 << 8)
+#define TSI108_EC_RXQ_BUFCFG_WSWP	(1 << 11)
+#define TSI108_EC_RXQ_BUFCFG_BSWP	(1 << 10)
+#define TSI108_EC_RXQ_BUFCFG_SFNPORT	0
+
+#define TSI108_EC_RXCTRL		(0x324)
+#define TSI108_EC_RXCTRL_ABORT		(1 << 30)
+#define TSI108_EC_RXCTRL_GO		(1 << 15)
+#define TSI108_EC_RXCTRL_QUEUE0		(1 << 0)
+
+#define TSI108_EC_RXERR			(0x378)
+
+#define PHY_CTRL			0
+#define PHY_CTRL_RESET			(1 << 15)
+#define PHY_CTRL_AUTONEG_EN		(1 << 12)
+#define PHY_CTRL_POWERDOWN		(1 << 11)
+#define PHY_CTRL_AUTONEG_START		(1 << 9)
+
+#define PHY_STAT			1
+#define PHY_STAT_LINKUP			(1 << 2)
+
+#if (TSI108_PHY_TYPE == PHY_MV88E)
+/* Marvel 88E1xxx-specific */
+#define PHY_SUM_STAT			0x11
+#define PHY_SUM_STAT_SPEED_MASK		(3 << 14)
+#define PHY_SUM_STAT_SPEED_10		(0 << 14)
+#define PHY_SUM_STAT_SPEED_100		(1 << 14)
+#define PHY_SUM_STAT_SPEED_1000		(2 << 14)
+#define PHY_SUM_STAT_FULLDUPLEX		(1 << 13)
+
+#define PHY_SUM_STAT_1000T_FD    (PHY_SUM_STAT_SPEED_1000 | PHY_SUM_STAT_FULLDUPLEX)
+#define PHY_SUM_STAT_1000T_HD    (PHY_SUM_STAT_SPEED_1000)
+#define PHY_SUM_STAT_100TX_FD    (PHY_SUM_STAT_SPEED_100 | PHY_SUM_STAT_FULLDUPLEX)
+#define PHY_SUM_STAT_100TX_HD    (PHY_SUM_STAT_SPEED_100)
+#define PHY_SUM_STAT_10T_FD	    (PHY_SUM_STAT_SPEED_10 | PHY_SUM_STAT_FULLDUPLEX)
+#define PHY_SUM_STAT_10T_HD	    (PHY_SUM_STAT_SPEED_10)
+#elif (TSI108_PHY_TYPE == PHY_BCM54XX)
+/*Broadcom BCM54xx */
+#define PHY_SUM_STAT			0x19
+#define PHY_SUM_STAT_SPEED_MASK		(7 << 8)	/* Auto Negotiation HCD */
+#define PHY_SUM_STAT_1000T_FD		(7 << 8)	/* 1000BASE-T Full-Duplex */
+#define PHY_SUM_STAT_1000T_HD		(6 << 8)	/* 1000BASE-T Half-Duplex */
+#define PHY_SUM_STAT_100TX_FD		(5 << 8)	/* 100BASE-TX Full-Duplex */
+#define PHY_SUM_STAT_100T4		(4 << 8)	/* 100BASE-T4 */
+#define PHY_SUM_STAT_100TX_HD		(3 << 8)	/* 100BASE-TX Half-Duplex */
+#define PHY_SUM_STAT_10T_FD		(2 << 8)	/* 10BASE-T Full-Duplex */
+#define PHY_SUM_STAT_10T_HD		(1 << 8)	/* 10BASE-T Half-Duplex */
+#define PHY_SUM_STAT_AN_FAIL		(0 << 8)	/* 1000BASE-T Half-Duplex */
+#else
+#error "PHY Device not specified"
+#endif				/* MV88_PHY */
+
+#define TSI108_TX_EOF	(1 << 0)	/* End of frame; last fragment of packet */
+#define TSI108_TX_SOF	(1 << 1)	/* Start of frame; first frag. of packet */
+#define TSI108_TX_VLAN	(1 << 2)	/* Per-frame VLAN: enables VLAN override */
+#define TSI108_TX_HUGE	(1 << 3)	/* Huge frame enable */
+#define TSI108_TX_PAD	(1 << 4)	/* Pad the packet if too short */
+#define TSI108_TX_CRC	(1 << 5)	/* Generate CRC for this packet */
+#define TSI108_TX_INT	(1 << 14)	/* Generate an IRQ after frag. processed */
+#define TSI108_TX_RETRY	16	/* 4 bit field indicating num. of retries */
+#define TSI108_TX_COL	(1 << 20)	/* Set if a collision occured */
+#define TSI108_TX_LCOL	(1 << 24)	/* Set if a late collision occured */
+#define TSI108_TX_UNDER	(1 << 25)	/* Set if a FIFO underrun occured */
+#define TSI108_TX_RLIM	(1 << 26)	/* Set if the retry limit was reached */
+#define TSI108_TX_OK	(1 << 30)	/* Set if the frame TX was successful */
+#define TSI108_TX_OWN	(1 << 31)	/* Set if the device owns the descriptor */
+
+/* Note: the descriptor layouts assume big-endian byte order. */
+typedef struct {
+	u32 buf0;
+	u32 buf1;		/* Base address of buffer */
+	u32 next0;		/* Address of next descriptor, if any */
+	u32 next1;
+	u16 vlan;		/* VLAN, if override enabled for this packet */
+	u16 len;		/* Length of buffer in bytes */
+	u32 misc;		/* See TSI108_TX_* above */
+	u32 reserved0;		/*reserved0 and reserved1 are added to make the desc */
+	u32 reserved1;		/* 32-byte aligned */
+} __attribute__ ((aligned(32))) tx_desc;
+
+#define TSI108_RX_EOF	(1 << 0)	/* End of frame; last fragment of packet */
+#define TSI108_RX_SOF	(1 << 1)	/* Start of frame; first frag. of packet */
+#define TSI108_RX_VLAN	(1 << 2)	/* Set on SOF if packet has a VLAN */
+#define TSI108_RX_FTYPE	(1 << 3)	/* Length/Type field is type, not length */
+#define TSI108_RX_RUNT	(1 << 4)/* Packet is less than minimum size */
+#define TSI108_RX_HASH	(1 << 7)/* Hash table match */
+#define TSI108_RX_BAD	(1 << 8)	/* Bad frame */
+#define TSI108_RX_OVER	(1 << 9)	/* FIFO overrun occured */
+#define TSI108_RX_TRUNC	(1 << 11)	/* Packet truncated due to excess length */
+#define TSI108_RX_CRC	(1 << 12)	/* Packet had a CRC error */
+#define TSI108_RX_INT	(1 << 13)	/* Generate an IRQ after frag. processed */
+#define TSI108_RX_OWN	(1 << 15)	/* Set if the device owns the descriptor */
+
+typedef struct {
+	u32 buf0;		/* Base address of buffer */
+	u32 buf1;		/* Base address of buffer */
+	u32 next0;		/* Address of next descriptor, if any */
+	u32 next1;		/* Address of next descriptor, if any */
+	u16 vlan;		/* VLAN of received packet, first frag only */
+	u16 len;		/* Length of received fragment in bytes */
+	u16 blen;		/* Length of buffer in bytes */
+	u16 misc;		/* See TSI108_RX_* above */
+	u32 reserved0;		/* reserved0 and reserved1 are added to make the desc */
+	u32 reserved1;		/* 32-byte aligned */
+} __attribute__ ((aligned(32))) rx_desc;
+
+#endif				/* __TSI108_ETH_H */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux