Re: [RESEND] [PATCH 2/2] ipaq.c timing parameters

["Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br>]

On Mon, 19 Jun 2006 19:34:28 +0200
Frank Gevaerts <frank.gevaerts@fks.be> wrote:

| On Mon, Jun 19, 2006 at 01:42:40PM -0300, Luiz Fernando N. Capitulino wrote:
| > On Mon, 19 Jun 2006 10:46:19 +0200
| > Frank Gevaerts <frank.gevaerts@fks.be> wrote:
| > 
| > | Adds configurable waiting periods to the ipaq connection code. These are
| > | not needed when the pocketpc device is running normally when plugged in,
| > | but they need extra delays if they are physically connected while
| > | rebooting.
| > | There are two parameters :
| > | * initial_wait : this is the delay before the driver attemts to start the
| > |   connection. This is needed because the pocktpc device takes much
| > |   longer to boot if the driver starts sending control packets too soon.
| > | * connect_retries : this is the number of times the control urb is
| > |   retried before finally giving up. The patch also adds a 1 second delay
| > |   between retries.
| > | I'm not sure if the cases where this patch is useful are general enough
| > | to include this in the kernel.
| > | 
| > | Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
| > | 
| > | diff -urp linux-2.6.17-rc6.a/drivers/usb/serial/ipaq.c linux-2.6.17-rc6.b/drivers/usb/serial/ipaq.c
| > | --- linux-2.6.17-rc6.a/drivers/usb/serial/ipaq.c	2006-06-14 16:02:03.000000000 +0200
| > | +++ linux-2.6.17-rc6.b/drivers/usb/serial/ipaq.c	2006-06-14 16:06:44.000000000 +0200
| > | @@ -71,6 +71,8 @@
| > |  
| > |  static __u16 product, vendor;
| > |  static int debug;
| > | +static int connect_retries = KP_RETRIES;
| > | +static int initial_wait;
| > |  
| > |  /* Function prototypes for an ipaq */
| > |  static int  ipaq_open (struct usb_serial_port *port, struct file *filp);
| > | @@ -583,7 +585,7 @@ static int ipaq_open(struct usb_serial_p
| > |  	struct ipaq_private	*priv;
| > |  	struct ipaq_packet	*pkt;
| > |  	int			i, result = 0;
| > | -	int			retries = KP_RETRIES;
| > | +	int			retries = connect_retries;
| > |  
| > |  	dbg("%s - port %d", __FUNCTION__, port->number);
| > |  
| > | @@ -647,6 +649,7 @@ static int ipaq_open(struct usb_serial_p
| > |  	port->read_urb->transfer_buffer_length = URBDATA_SIZE;
| > |  	port->bulk_out_size = port->write_urb->transfer_buffer_length = URBDATA_SIZE;
| > |  	
| > | +	msleep(1000*initial_wait);
| > 
| >  I was going to say you should use ssleep() here, but I can't find a
| > ssleep_interruptible(). Then either: use msleep_interruptible() or
| > creates a new ssleep_interruptible().
| 
| I wasn't sure if that was safe here, so I used the non-interruptible
| version. I'll change it when I redo the patch.
| Is it worth it creating ssleep_interruptible() just for this one call?

 You could grep around to check it.

-- 
Luiz Fernando N. Capitulino
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/